TAS 100 is the World’s Most
Popular Family of Modem &
Fax Test Instruments
For years, TAS 100 Series Telephone
Network Emulators have been the choice
of leading data communications
equipment manufacturers and
evaluators worldwide. TAS 100 now
gives you all of the tools necessary to
test the latest and most complex modem
and fax modulation schemes. TAS 100
assures high product quality and
eliminates costly and embarrassing field
failures by providing a comprehensive
set of testing capabilities. The investment
in a TAS 100 Series Telephone Network
Emulator can return many times its cost
by eliminating product repairs and lost
sales due to poor product quality.
The latest member of the TAS 100 Series
family, the TAS 192 thoroughly tests all
types of modems. TAS 192 meets and
exceeds the requirements of the latest
EIA/TIA industry testing standards,
including TSB 37A. Enhanced frequency
response characteristics provide a more
accurate test bench for V.34 and V.34+
modems. TAS 192 also emulates
conditions typically associated with local
network connections, including short
transmission delay and low trunk loss.
Modem performance in one of today’s
most common applications, Internet
access over local telephone lines, can
now be accurately evaluated. TAS 192
also contains a wide range of other
impairments to fully exercise modem
performance in a variety of real-world
conditions.
TAS 100 Provides a Thorough,
Accurate Test for any Device
that Communicates over
Voice-Bandwidth Telephone
Networks
All TAS 100 Series models emulate a
complete, end-to-end telephone
connection and can be configured to
represent 2-wire dial, 2-wire private,
and 4-wire private lines. The units can
also be configured as 4-wire at one
station and 2-wire at the other station
to facilitate testing cellular modems
and remote access servers. In addition,
the TAS 192 can be configured with a
new line mode to allow two units to be
cascaded together to simulate the
effects of digital loop carrier (DLC)
systems and private branch exchange
(PBX) environments on modem
performance. TAS 100 also includes
programmable control of network
configuration, central office (exchange)
configuration, analog transmission
impairments, digital facility
impairments such as PCM and robbed
bit signalling, and delay and echo levels.
TAS 100 provides the mix of critical
features required for thorough
evaluation in a compact, easy-to-use
package. Designers can drama-tically
reduce development testing time and
costs. Manufacturers can detect and
stop defective products before they
reach the field. Product evaluators
can select between data
communications products based on
real-life performance, not just the
specification sheet.
In short, TAS 100 helps you to
insure the quality of your modem,
fax, or other data communications
products.
Every TAS 100 Series Telephone
Network Emulator lets you quickly
and easily evaluate
communications equipment
performance with respect to:
■
Central office conditions such
as loop current, ring voltage,
call progress tones, etc.
■
Transmission impairments such
as attenuation, gain distortion,
group delay distortion, PCM
distortion, robbed-bit signalling,
and much more
■
Satellite delay and echo
TAS 100 is the easy way to test modems,
fax machines, telephone sets, and more!
Applications:
■
Product
Development
■
Engineering Test
■
Quality Assurance
■
Manufacturing Test
/QC
TAS 100 tests and evaluates data
communications products such as:
TAS 100 Series provides bidirectional impairments and echo emulation for
accurate results and adherence to current modem testing standards.
AB
Impairments
Generator
BA
Impairments
Generator
Echo
Central
Office
Emulator
A
TAS 100 also tests and evaluates products that
contain modems, such as:
■
Credit Card
Verification
Terminals
■
Automatic Teller
Machines
■
Facsimile Machines
■
Stock Transaction
Terminals
■
Remote Data Entry
Terminals
Station
Set
B
1-800-927-2660
www.spirentcom.com
TAS 100 Series
Telephone Network Emulators
Pre-defined network
conditions for many
countries can be recalled at
the touch of a button!
TAS 100 Puts the World’s Telephone
Networks at Your Fingertips
Pre-defined network conditions for many countries
can be recalled at the touch of a button! TAS 100
also includes pre-defined
transmission impairments conditions
according to published Electronic
Industries Association (EIA)
specifications. Non-volatile storage
is provided for user-defined test
conditions.
TAS 100 Complies With U.S. and
International Standards for Modem
and Fax Testing
The TAS 100 Series meets or exceeds impairment
generation specifications put forth by EIA/TIA, ITU
(CCITT), Nippon Telephone and Telegraph (NTT),
AT&T, Bell System, RITT (China), and U.S.
Department of Defense. Built-in ROM files include
setups for standard test conditions to assure
compliance with existing and emerging
test standards.
No Other Solution Packs So Much
Testing Power Into A Single, Compact
Enclosure
TAS 100 Series Telephone Network Emulators give
you complete, bi-directional impairments emulation
(models 182 and 192) and fully automatic, dual
central office emulation, all in one compact package.
Unidirectional impairments models (151) are
upgradable to full impairments without adding
additional boxes.
TAS 100 Is Easy To Set Up
and Easy To Use
All TAS 100 operations are accessible via easy to
use front panel menus. TAS 100 also provides a
straightforward, logical set of remote commands
to facilitate remote control via RS-232 or GPIB. If
you’re designing your own automatic test software,
you’ll find that programming the TAS 100 is a
breeze.
TAS 100 Employs Advanced Digital Signal
Processing Technology Throughout for
Unsurpassed Accuracy, Repeatability, and
Reliability
The TAS 100 Series provides precise, all-digital
emulation of transmission impairments and call
progress tones for precisely repeatable test results.
Digital processing yields extremely low background
noise, so you get accurate test results even at the
lowest signal levels. Digital processing also yields
high reliability, because the overall component count
is kept to a minimum.
All-digital impairments mean rock-solid compatibility
among TAS 100 family members. TAS 100
impairments are compatible with IEEE 743-1984
specifications to facilitate easy verification of emulator
performance using standard measuring equipment.
Built-In Diagnostic Routines Insure the
Integrity of Your Test Results
Built-in diagnostics check the performance of all TAS
100 subsystems. TAS 100 executes a complete set
of self-diagnostics auto-matically upon power-up,
and upon user command.
The Icing on the Cake... Advanced
Measurement and Monitor Features!
The convenient Network Status Monitor shows call
progress status at a glance. TAS 100 also includes
several measurement functions to allow complete
evaluation of DCE performance.
These include:
■
True-RMS Level Meter
■
Dialed Digit Monitor/Display
■
Scope Monitor Port
■
Audio Monitor
2
TAS 100 is the Heart of a
Powerful Series of Advanced
Automatic Modem Test Systems:
TAS 100 Series Telephone Network
Emulators are designed to work with other
TAS products to provide complete solutions
for testing modems, fax machines, and a
host of other data communications
equipment. The TAS 100GT Series Automatic
Modem Test Systems provide a
comprehensive, automatic solution for testing
and evaluating virtually all types of modems,
including V.34 and V.34+. Each TAS 100GT
system includes:
■
TAS 100 Series Telephone Network Emulator
■
TAS Gemini Dual Terminal Emulator
■
TASKIT® Lab Suite for Windows Automatic
Modem Test Software
■
TAS 240 Voiceband Subscriber Loop
Emulator (optional)
■
TAS 3508A Modem Test Switch (optional)
With TAS 100GT, you can immediately begin
testing and evaluating modems. Each 100GT
system includes TASKIT Lab Suite for
Windows, which consists of TASKIT/Auto
and TASKIT for Windows instrument control
programs. TASKIT/Auto executes automatic
modem test procedures while the TASKIT
instrument control programs provide
interactive, menu-driven control of each
instrument in the test station. TASKIT Lab
Suite for Windows also includes pre-defined
test procedures based on the latest modem
industry standards, including EIA/TIA TSB
37A and TSB 38.
TAS 100GT Series Automatic Modem Test Systems provide a complete solution for testing virtually all modem types.
The Gemini Dual Terminal Emulator is by far the
most advanced solution available for testing modem
bit-error rate, file transfer throughput, call setup,
and call connect reliability. Gemini is the only data
analyzer that gives you complete end-to-end testing
in one compact package. Control of Gemini is
integrated into TASKIT/Gemini software menus.
The TAS 240 Voiceband Subscriber Loop Emulator
(VSLE) provides advanced loop emulation features
for testing echo-cancelling modems and high-speed
fax devices. TAS 240 accurately emulates subscriber
loop conditions to allow thorough evaluation of
loop loss and impedance characteristics. TAS 240
includes RS-232 and GPIB control interfaces for
easy inclusion in custom automatic test
procedures. TASKIT/240 provides integrated
control of the TAS 240.
The TAS 3508A Modem Test Switch works with
the TAS 100 to provide automatic modem selection
for development, manufacturing, or evaluation test
applications. TAS 3508A includes RS-232 and GPIB
remote control interfaces for easy integration into
the test station. TASKIT/Auto provides control
options for the TAS 3508A.
modem performance in the presence of real-world
New TASKIT®/100 for
Windows Software:
The powerful new TASKIT/100 for Windows
software provides an easy-to-use graphical
interface that gives point-and-click control
of all TAS 100 Series Telephone Network
Emulators. TASKIT/100 for Windows makes
it easy to create and save test network
configuration files.
TASKIT/100 for Windows software
provides point-and-click control
of all TAS 100 Series Telephone
Network Emulators, including the
new TAS 192.
3
TAS 100 Series
Telephone Network Emulators
Tas 100 Series At-A-Glance
Convenient Network
Status Monitor
shows network mode
and call progress
states at a glance.
Large, easy-to-read
display presents all
menu information
in a consistent
format.
TAS 100 provides easy-to-use menus for A
and B
➞
A impairments, central office settings,
signal measurement functions, system
configuration options, and file save and recall.
At the touch of a
single button, you can
perform an AGC operation
or bypass impairments in
either transmission
direction.
➞
B
All network interface signals are
available at rear panel terminal
strips as well as front panel RJ45
connectors.
Four-wire path breakout
capability allows you to insert
other equipment into the
transmission path.
Built-in GPIB and
RS-232 control ports make
it easy for you to include
TAS 100 in your own
automatic test system.
TAS 100 provides external hybrid balance ports:
essential for interfacing to a loop emulator for
complete characterization of high-speed echo
cancelling modems.
New! TAS 100 now provides ports
for quick and easy connection to
the TAS 240 Loop Emulator.
4
TAS 100 Series Applications
TAS 100 can be applied as a standalone telephone network emulator, or as part of an automatic test
system. TAS 100 can be used to test any product that communicates over the public switched telephone
network (PSTN). Simply replace the real network with the TAS 100 Series Telephone Network Emulator
and start testing!
Modem Evaluation
TAS 100 is the heart of a powerful,
advanced, automatic modem test
system. Test modems to the latest
industry standards.
Modem
Manufacturing Test
TAS provides cost-effective, complete
solutions for manufacturing test of
modems and FAX devices.
Modem
A
Test Data
Reference
Modem
RS-232 DataRS-232 Data
TAS 100 Series Telephone Network Emulator
Main
Loop A1
or Pad
LineLine
Hybrid
Balance
Loop A2
Voiceband Subscriber Loop Emulator (VSLE)
AB
Telephone Network Emulator
Dual Data Analyzer
A
TAS Gemini
TAS 100 Series
GEMINI
IMP
IMP
TAS 240
Hybrid
B
Balance
Loop B2
BA
Main
Loop B1
or Pad
Modem
B
Test Data
TAS 3508A
Modem Test Switch
Modem 1
Modem 2
Modem 9
PC Bus Modem Test
TAS PC-PodTM software accessory
makes testing PC internal modems
a snap. PC-Pod
between modem ports and serial
ports, so that bus modems can be
tested by standard data analyzers
such as TAS Gemini.
TM
shuttles data
RS-232
Data
Serial
Port
Telephone
Line
Modified Null
Modem Connector
RS-232
DTE
A
Internal
Modem
Serial
Port
TAS Gemini
TAS 100 Series
Telephone Network Emulator
Host PC with
PC-Pod Software
Parallel
Port
GPIB
DTE
Internal
Modem
Serial
Port
Software
Key
B
Telephone
Line
Modified Null
Modem Connector
RS-232
Data
5
TAS 100 Series
Telephone Network Emulators
TAS 100 Series Applications
FAX Testing
TAS 100 is the choice of FAX
manufacturers worldwide.
TAS 100 accurately simulates
network conditions to allow
thorough evaluation of FAX image
quality and call setup performance.
Communication
Software Evaluation
TAS 100 lets you evaluate
real-world performance of
communication software.
Facilitates thorough evaluation
of protocol error recovery,
throughput, and data
compression performance.
FAX Machine AFAX Machine B
Telephone
Line
DataLine
Modem
TAS 100 Series
Telephone Network Emulator
TAS 100 Series
Telephone Network Emulator
Telephone
Line
LineData
BA
Modem
Testing Systems with
Embedded Modems
Evaluate performance of products
that contain modems, such as credit
card verification terminals and point
of sale terminals.
Transmission Measuring
Set Evalualtion
TAS 100 makes it easy to verify
proper operation and accuracy of
transmission measuring sets.
Credit Card
Verification
Terminal
LineLine
BA
TAS 100 Series
Telephone Network Emulator
TAS 100 Series
Telephone Network Emulator
Transmission
XMTRCV
Impairments
Measuring Set
Host
Data
Modem
Host Computer
6
TAS 100 Series
Selection Guide:
The TAS 100 Series consists of four models. These models differ only in their impairments emulation
capabilities. All of the models have equal central office emulation capabilities. The TAS 100 Series Selection
Guide provides a comparison of the various models.
Feature150 151182192
Front Panel Menus●● ●●
GPIB and RS-232 Control●● ●●
Central Office Emulation●● ●●
Network Status Monitor●● ●●
Signal Level Measurement●● ●●
Dialed Number Display & Report●● ●●
DTMF & Dial Pulse Detection●● ●●
Input & Output AGCs●● ●●
Attenuation●● ●●
Echo●● ●●
Satellite Delay●●●
White Noise●●●
Gain and Delay Distortion●●●
Intermodulation Distortion●●
TAS 100 Series
Ordering Information:
Model
TAS 100 Series Models:
TAS 192 Telephone Network Emulator
TAS 182 Telephone Network Emulator
TAS 151 Telephone Network Emulator
TAS 150 Telephone Network Emulator
Model
Feature150 151182192
Frequency Offset●●
Phase Jitter●●
Impulses●●
Gain Hits●●
Phase Hits●●
Single Frequency Interface●●
Amplitude Jitter●●
PCM Emulation: # of links01 3 3
Robbed Bit Signalling Emulation●●●
TIA TSB-37A Test Files●●
Bidirectional Impairments●●
Enhanced Delay Emulation●
Enhanced TIA Gain and
Delay Curves
True-VoiceTM is a trademark of AT&T
●
TAS 100 Series Accessories:
TAS 100-0 Extra Operations Manual
TAS 100-RMRack Mount Kit
TAS LIA-01Line Interface Adaptor
TAS 100-HCHard Shipping Case
TAS 100-SCSoft Carrying Case
7
TAS 100 Series
Telephone Network Emulators
TAS 100 Series Specifications
Impairments Generator
Input Level Range+7.0 dBm to -23.0 dBm
Output Level Range0.0 dBm to -50.0 dBm
PCM
Number of Links0-3
Sampling Rate8.0 kHz
Sample Codingnone, mu-law, or A-law
Positionbefore or after analog impairments
Robbed Bit Signalling
Bits Affectedleast significant bit of every 6th PCM sample
Patternalternating 1/0
2nd Order Range20 dB to 55 dB below signal
3rd Order Range20 dB to 55 dB below signal
Typeexpansive or compressive
Frequency Shift
Offset-19.75 to 19.75 Hz
Phase Jitter
Level Range0.0 to 45.0 degrees p-p
Frequency Range0.0 to 300.0 Hz
Gain Hits
Level Range-20.0 to +6.0 dB
Risetime Range0.2 to 990 msec.
Duration Range1.0 to 20000 msec.
Interval Range0.1 to 320.0 sec.
Phase Hits
Level Range0.0 to 90.0 degrees
Risetime Range0.2 to 990 msec.
Duration Range1.0 to 20000 msec.
Interval Range0.1 to 320.0 sec.
Impulse Noise
TypeIEEE Standard
Level Range0.0 to 55.0 dB below signal
Interval Range0.1 to 320.0 sec.
CalibrationC-notched
Amplitude Jitter
Level Range0.0 to 98.0%
Frequency Range0.0 to 300.0 Hz
Single Frequency Interference
Frequency Range0.0 to 3400.0 Hz
Level Range0.0 to 50.0 dB below signal output level
Gain Distortion
Note: Gain Distortion characteristics are independent of group delay distortion characteristics. TAS
192 contains only the gain distortion characteristics listed in bold. Those TAS 192 gain distortion
characteristics have better frequency responses at the upper and lower edges of the voiceband than
the same gain distortion characteristics in other TAS 100 Series models.
Filter TypeDigital FIR
Gain Distortion
CharacteristicsFlat, AD1-7, “V.FAST”/ ITU Cable-1, Cable-2, and Cable-3, JAPAN 1-
Group Delay Distortion
Note: Group Delay Distortion characteristics are independent of gain distortion characteristics. TAS
192 contains only the group delay distortion characteristics listed in bold. Those TAS 192 group delay
distortion characteristics have better frequency responses at the upper and lower edges of the voiceband
than the same group delay distortion characteristics in other TAS 100 Series models.
Filter TypeDigital IIR
Group Delay Distortion
CharacteristicsFlat, EDD1, TAS-1, JAPAN 1-7, RITT 1-2 (China),
Propagation Delay
Range0 to 1599.875 msec.
Resolution125
Echo
Far Echo Attenuation Level -20.0 to +30.0 dB
Near Echo Attenuation Level -10.0 to +40.0 dB
7, RITT (China), TR50150 (True Voice), TAS 3002, SEG 3002, Bell C1,
Bell C2, Bell C4, CCITT 1020, CCITT M1025, CCITT M1040, EIA A, EIA
B, EIA C, CONUS MD, CONUS MV, CONUS PD, CONUS PV, DOD NSB,
DOD NTB, EUROPEAN MD, EUROPEAN MV, EUROPEAN PD, EUROPEAN
PV, CCITT R.28
TAS 3002, SEG 3002, Bell C1, Bell C2, Bell C4, CCITT M1020, CCITT
M1025, EIA 1-5, CONUS MD, CONUS MV, CONUS PD, CONUS PV,
DOD NSB, DOD NTB, EUROPEAN MD, EUROPEAN MV, EUROPEAN PD,
EUROPEAN PV, CCITT R.28
* The site A 2-wire switched and site B 2-wire switched central office operating modes are present only
in the TAS 192. These operating modes have been added to support connecting two TAS 192 units
together to simulate digital loop carrier (DLC) facilities and private branch exchange (PBX) environments.
4-wire private line, 4-wire private/2-wire switched, site A 2-wire switched
(*), site B 2-wire switched (*)
Range8 to 120 mA in 8 mA steps
Polaritytip to ring, ring to tip
Ring Generator
Level1 to 100 Vrms (open circuit), 1V steps
Frequency14.0 to 75.0 Hz
Cadence1-3 ON intervals, 1-3 OFF intervals
Ring ON/OFF Intervals0 to 10,000 msec.
Source Impedance2100 ohms typical
Network Signalling Tones
Tones Supportedprimary and secondary dial tones, busy, audible ringing
Dial Tone/Audible
Ring Cadence1-3 ON intervals, 1-3 OFF intervals
Busy Cadence1 ON intervals, 1 OFF interval
ON/OFF Intervals0 to 10,000 msec.
Tone Frequency100.0 to 720.0 Hz
Touch Tone Detection
Detection Range0.0 to -25.0 dBrn
Max. Invalid Tone Duration 20.0 msec.
Max. Interdigit Pause40.0 msec.
Max. Dropout20.0 msec.
Dial Pulse Detection
Make/Break Interval Range 10 to 90 msec.
Min. Interdigit Pause300 msec.
Call Progress Parameters
Max. Digits in
Telephone Number15
Switching Delay1 to 25,000 msec.
Off Hook Delay2 to 25,000 msec.
On Hook Delay1 to 255 msec.
Disconnect Signalling
Signal Optionsno signal, busy tone, dial tone
Delay Before Signal1 to 30,000 msec. in 1 msec. steps
- continued
Signal Level Measurements
Range+10.0 to -50.0 dBrn
Resolution0.1 dB
Accuracy±0.4 dBm
Measurement Pointsinput and output of each transmission channel
Control Interfaces
Interfaces Provided
Serial Control Port Parameters
Bit Rates1200, 2400, 4800, 9600 bps
Formatasynchronous
Bits/Char7 or 8
Parityeven, odd, none
Stop Bits1, 1.5, 2
AC Line
Voltage115/ 230 VAC (selectable) +10%, -13%
Frequency48 to 63 Hz
Max. Power Dissipation100 Watts
Operating Environment
Temperature0 to 50o C (32 to 122o F)
Humidity10 to 90%, non-condensing