Atec MT8212E, MT8213E User Manual

Technical Data Sheet

™

Cell Master

Compact Handheld Base Station Analyzer

MT8212E MT8213E

2 MHz to 4 GHz 2 MHz to 6 GHz Cable & Antenna Analyzer 9 kHz to 4 GHz 9 kHz to 6 GHz Spectrum Analyzer 10 MHz to 4 GHz 10 MHz to 6 GHz Power Meter

Introduction

Anritsu introduces its latest generation compact handheld Base Station Analyzer for installation and maintenance of wireless networks. Designed as a lightweight base station analyzer meeting virtually all the testing needs of an RF technician, the Cell Master features Signal Analyzer options for 2G, 3G, and 4G cellular networks including LTE, WiMAX, and for digital broadcast.

Cable and Antenna Analyzer Highlights Spectrum and Interference Analyzer Highlights

• Measurements: RL, VSWR, Cable Loss, DTF, Phase

• 2-port Transmission Measurement: High/Low Power

• Sweep Speed: 1 ms/data point, typical

• Display: Single or Dual Measurement Touchscreen

• Calibration: OSL, InstaCal™, and FlexCal™

• Bias Tee: 32 V internal

Capabilities and Functional Highlights

• LTE , TD-LTE (20 MHz B/W)

• GSM/EDGE

• W-CDMA/HSPA+

• TD-SCDMA/HSPA+

• CDMA, EV-DO

• Fixed, Mobile WiMAX

• ISDB-T, ISDB-T SFN

• DVB-T/H, DVB-T/H SFN

• PIM Analyzer

• Interference Analyzer

• GPS information on stored

traces

• Measurements: Occupied Bandwidth, Channel Power, ACPR, C/I

• Interference Analyzer: Spectrogram, Signal Strength, RSSI,

Interference Mapping

• Dynamic Range: > 102 dB in 1 Hz RBW

• DANL: –162 dBm in 1 Hz RBW

• Phase Noise: –100 dBc/Hz max @ 10 kHz offset at 1 GHz

• Frequency Accuracy: ± 50 ppb with GPS On

• Built-in Bias Tee

• Internal Power Meter

• High Accuracy Power Meter

• USB Power Sensors, 4 GHz to

26 GHz

• Coverage Mapping

• E1, T1, T3 Backhaul Analyzer

• 3 hour battery operation time

• USB data transfer

• Master Software Tools™

• Line Sweep Tools™

• easyTest Tools™

Cell Master™ MT8212E/MT8213E Base Station Analyzer featuring 8.4 inch Daylight Viewable Touchscreen

Compact Size: 273 mm x 199 mm x 91 mm, (10.7 inch x 7.8 inch x 3.6 inch), Lightweight: 3.71 kg, (8.2 lbs)

Specifications Cell Master™ MT8212E and MT8213E

Cable and Antenna Analyzer

Measurements

Setup Parameters

Measurement Display

Frequency

Windowing

Amplitude

Sweep

Data Points

Markers

Tra ce s

Limit Line

Calibration

Save/Recall

Frequency

Frequency Range

Frequency Accuracy≤ ± 2.5 ppm @ 25 ºC

Frequency Resolution

Output Power

Interference Immunity

On-Channel

On-Frequency

Measurement Speed

Return Loss≤ 1.00 ms/data point, RF immunity low, typical

Distance-to-Fault≤ 1.25 ms/data point, RF immunity low, typical

Return Loss

Measurement Range

Resolution

VSWR

Measurement Range

Resolution

Cable Loss

Measurement Range

Resolution

Distance-to-Fault

Vertical Range Return Loss

Vert ic al Range VSW R

Fault Resolution (meters)

Horizontal Range (meters)

1-Port Phase

Measurement Range

Resolution

Smith Chart

Resolution

VSWR Return Loss Cable Loss Distance-to-Fault (DTF) Return Loss Distance-to-Fault (DTF) VSWR 1-Port Phase

Smith Chart (50/75

Single/Dual Measurement Display with independent markers Start/Stop, Signal Standard, Start Cal

DTF

Start/Stop, DTF Aid, Units (m/ft), Cable Loss, Propagation Velocity, Cable, Windowing Rectangular, Normal Side Lobe, Low Side Lobe, Minimum Side Lobe Top, Bottom Auto Scale, Full Scale Run/Hold, Single/Continuous, RF Immunity (High/Low), Data Points, Averaging/Smoothing,

Output Power (High/Low), RF Pwr When Hold (On/Off) 137, 275, 551, 1102, 2204 Markers 1-6 (On/Off), Delta Makers 1-6 (On/Off), Marker to Peak/Valley, Peak/Valley Auto,

Marker Table (On/Off ), All Markers Off Recall, Copy to Display Memory, No Trace Math, Trace ± Memory, Trace Overlay (On/Off) On/Off, Single Limit, Multi-segment Edit, Limit Alarm (On/Off), Pass Fail Message (On/Off), Pass/Fail

(Unbounded/Bounded), Warning Limit Offset, Clear Limit Start Cal, Cal Type (Standard/FlexCal), Disp Valid Cal Temp Range Setups, Measurements, Screen Shots (.jpg) (save only)

2 MHz to 4 GHz (MT8212E), 2 MHz to 6 GHz (MT8213E)

1 kHz (RF immunity low), 100 kHz (RF immunity high)

High

0 dBm, typical

Low

–30 dBm, typical

+17 dBm @ > 1.0 MHz from carrier frequency 0 dBm within ± 10 kHz of the carrier frequency

0 dB to 60 dB

0.01 dB

1:1 to 65:1

0.01

0 dB to 30 dB

0.01 dB

0 dB to 60 dB 1:1 to 65:1 (1.5 x 108 x vp) / ΔF (vp = velocity propagation constant, ΔF is F2–F1 in Hz) 0 to (Data Points–1) x Fault Resolution, to a maximum of 1500 meters (4921 feet)

–180º to +180º

0.01º

0.01 50/75 Ohm Selectable

selectable)

2 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

0.1

-40 -30 -20 Return Loss (dB)

Uncertainity (dB)

-10 0

Reecon Magnitude Uncertainty

< 4 GHz

4 to 6 GHz

100

-40 -30 -20 Return Loss (dB)

Uncertainity (degrees)

-10 0

Reecon Phase Uncertainty

< 4 GHz

4 to 6 GHz

Cable and Antenna Analyzer (Continued)

Measurement Accuracy

Corrected Directivity

> 42 dB, OSL Calibration > 38 dB, InstaCal™ Calibration

Measurement Uncertainty

PIM Analyzer (Requires PIM Master™)

See Product Brochure 11410-00546

2-Port Transmission Measurement (Option 0021)

Frequency

Frequency Range

Frequency Resolution

2 MHz to 4 GHz (MT8212E), 2 MHz to 6 GHz (MT8213E) 10 Hz

Output Power

High

0 dBm, typical

Low

–30 dBm, typical

High Dynamic Range (On)

2 MHz to 4 GHz 4 GHz to 6 GHz

Application Options

80 dB, 95 dB, typical 70 dB, 85 dB, typical Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)

Bias-Tee (Option 0010)

Setup

Voltage Range

Current (Low/High)

Resolution

On/Off, Voltage, Current (Low/High) +12 V to +32 V 250 mA/450 mA, 1 A surge for 100 ms

0.1 V

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 3 of 32

Specifications Cell Master™ MT8212E and MT8213E

Spectrum Analyzer

Measurements

Smart Measurements

Setup Parameters

Frequency

Amplitude

Bandwidth

Save/Recall

Save-on-Event

Delete

Directory Management

Application Options

Sweep Functions

Sweep

Detection

Triggers

Trace Functions

Tra ce s Trace A Operations Trace B OperationsA → Trace C OperationsA →

Marker Functions

Markers

Marker Types

Marker Auto-Position

Marker Table

Limit Line Functions

Limit Lines

Limit Line Edit

Limit Line Move

Limit Line Envelope

Limit Line Advanced

Frequency

Frequency Range

Tuning Resolution

Frequency Reference

Frequency Span

Sweep Time

Sweep Time Accuracy

Bandwidth

Resolution Bandwidth (RBW)

Video Bandwidth (VBW) RBW with Quasi-Peak Detection VBW with Quasi-Peak Detection

Field Strength (uses antenna calibration tables to measure dBm/m2, dBmV/m, dBV/m, dBμV/m, Volt/m,

Watt/m

, dBW/m2, A/m, dBA/m and Watt/cm2) Occupied Bandwidth (measures 99 % to 1 % power channel of a signal) Channel Power (measures the total power in a specified bandwidth) ACPR (adjacent channel power ratio) AM/FM/SSB Demodulation (wide/narrow FM, USB and LSB), (audio out only) C/I (carrier-to-interference ratio) Emission Mask Coverage Mapping (requires Option 0431)

Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Channel Increment Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection

Span

Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span R B W, A u t o R B W, V B W, A u t o V B W, R BW / VB W, Sp a n/ R BW

File

Save, Recall, Delete, Directory Management Setups, Measurements, Limit Lines, Screen Shots (.jpg) (save only), Save-on-Event Crossing Limit Line, Sweep Complete, Save-then-Stop, Clear All Selected File, All Measurements, All Mode Files, All Content Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy, Format USB Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)

Single/Continuous, Sweep Mode (Fast, Performance, No FFT), Reset, Detection, Minimum Sweep Time, Trigger Type, Gated Sweep (see Option 0090)

Peak, RMS, Negative, Sample, Quasi-peak Free Run, External, Video, Change Position, Manual

Up to three Traces (A, B, C), View/Blank, Write/Hold, Trace A/B/C Operations Normal, Max Hold, Min Hold, Average, # of Averages, (always the live trace)

B, B ↔ C, Max Hold, Min Hold

C, B ↔ C, Max Hold, Min Hold, A – B → C, B – A → C, Relative Reference (dB), Scale

Markers 1-6 each with a Delta Marker, or Marker 1 Reference with Six Delta Markers, Marker Table (On/Off), All Markers Off

Style (Fixed/Tracking), Noise Marker, Frequency Counter Marker Peak Search, Next Peak (Right/Left), Peak Threshold %, Set Marker to Channel, Marker Frequency to

Center, Delta Marker to Span, Marker to Reference Level 1-6 markers frequency and amplitude plus delta markers frequency amplitude and offset

Upper/Lower, On/Off, Edit, Move, Envelope, Advanced, Limit Alarm, Default Limit Frequency, Amplitude, Add Point, Add Vertical, Delete Point, Next Point Left/Right To Current Center Frequency, By dB or Hz, To Marker 1, Offset from Marker 1 Create Envelope, Update Amplitude, Points (41 max), Offset, Shape Square/Slope Type (Absolute/Relative), Mirror, Save/Recall

9 kHz to 4 GHz (MT8212E), 9 kHz to 6 GHz (MT8213E) 1 Hz Aging: ± 1.0 ppm/year

Accuracy: ± 1.5 ppm (25 °C ± 25 °C) + aging, < ± 50 ppb with GPS On 10 Hz to 4 GHz including zero span (MT8212E), 10 Hz to 6 GHz including zero span (MT8213E) Minimum 100 ms, 10 µs to 600 s in zero span ± 2 % in zero span

1 Hz to 3 MHz in 1–3 sequence ± 10% (1 MHz max in zero-span) (–3 dB bandwidth) 1 Hz to 3 MHz in 1–3 sequence (–3 dB bandwidth) 200 Hz, 9 kHz, 120 kHz (–6 dB bandwidth) Auto VBW is On, RBW/VBW = 1

4 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

Spectrum Analyzer (Continued)

Spectral Purity

SSB Phase Noise @ 1 GHz

Amplitude Ranges

Dynamic Range

Measurement Range

Display Range

Reference Level Range

Maximum Continuous Input Power

Attenuator Range

Amplitude Units

Amplitude Accuracy

9 kHz to 100 kHz 100 kHz to 4.0 GHz > 4.0 GHz to 6 GHz

Displayed Average Noise Level (DANL)

(RBW = 1 Hz, 0 dB attenuation) Maximum Typical Maximum Typical

10 MHz to 2.4 GHz –141 dBm –146 dBm –157 dBm –162 dBm

> 2.4 GHz to 4 GHz –137 dBm –141 dBm –154 dBm –159 dBm

> 4 GHz to 5 GHz –134 dBm –138 dBm –150 dBm –155 dBm

> 5 GHz to 6 GHz –126 dBm –131 dBm –143 dBm –150 dBm

–100 dBc/Hz, –110 dBc/Hz typical @ 10 kHz offset –105 dBc/Hz, –112 dBc/Hz typical @ 100 kHz offset –115 dBc/Hz, –121 dBc/Hz typical @ 1 MHz offset

> 102 dB (2.4 GHz), 2/3 (TOI-DANL) in 1 Hz RBW DANL to +26 dBm 1 dB to 15 dB/div in 1 dB steps, ten divisions displayed –120 dBm to +30 dBm +30 dBm 0 dB to 55 dB in 5 dB steps Log Scale Modes: dBm, dBV, dBmV, dBμV, dBW, dBmW, dBμW, dBA, dBmA, dBμA

Linear Scale Modes: nV,

± 2.00 dB typical ± 1.25 dB, ± 0.5 dB typical ± 1.50 dB, ± 0.5 dB typical

(Reference Level –20 dBm)

V, m V, V, kV, n W, μW, m W, W, k W, n A , μA, mA, A

Preamp Off

Preamp On

(Reference Level –50 dBm)

Spurs

Residual Spurious

Input-Related Spurious

Exceptions, typical

Third-Order Intercept (TOI)

800 MHz

2400 MHz

200 MHz to 2200 MHz

> 2.2 GHz to 5.0 GHz > 5.0 GHz to 6.0 GHz

Second Harmonic Distortion

50 MHz

> 50 MHz to 200 MHz

> 200 MHz to 3000 MHz

VSWR

< –90 dBm (RF input terminated, 0 dB input attenuation, > 10 MHz) < –75 dBc (0 dB attenuation, –30 dBm input, span < 1.7 GHz, carrier offset > 4.5 MHz) < –70 dBc @ < 2.5 GHz, with 2072.5 MHz Input

< –68 dBc @ F1 – 280 MHz with F1 Input < –70 dBc @ F1 + 190.5 MHz with F1 Input < –52 dBc @ 7349 – (2F2) MHz, with F2 Input, where F2 < 2424.5 MHz < –55 dBc @ 190.5 ± (F1/2) MHz, where F1 < 1 GHz

Preamp Off (–20 dBm tones 100 kHz apart, 10 dB attenuation) +16 dBm +20 dBm +25 dBm, typical +28 dBm, typical +33 dBm, typical

Preamp Off, 0 dB input attenuation, –30 dBm input –56 dBc –60 dBc, typical –70 dBc, typical

2:1, typical

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 5 of 32

Specifications Cell Master™ MT8212E and MT8213E

Coverage Mapping (Options 0431)

Measurements

Indoor Mapping Outdoor Mapping

RSSI ACPR

RSSI

ACPR

Setup Parameters

Frequency

Amplitude

Measurement Setup

Point Distance / Time Setup

Save Points Map

Recall Points Map

Center/Start/Stop, Span, Freq Step, Signal Standard, Channel #, Channel Increment Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Pre-Amp On/Off, Detection

Span

Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span

R B W, A u t o R B W, V B W, A u t o V B W, R BW / VB W, Sp a n/ V BW ACPR, RSSI Repeat Type Time Distance Save KML, JPEG, Tab Delimited Recall Map, Recall KML Points only, Recall KML Points with Map, Recall Default Grid

Interference Analyzer (Option 0025)

Measurements

Application Options

Spectrum

Field Strength Occupied Bandwidth Channel Power Adjacent Channel Power Ratio (ACPR) AM/FM/SSB Demodulation (Wide/Narrow FM, Upper/Lower SSB), (audio out only)

Carrier-to-Interference ratio (C/I) Spectrogram (Collect data up to one week) Signal Strength (Gives visual and aural indication of signal strength) Received Signal Strength Indicator (RSSI) (collect data up to one week)

Gives visual and aural indication of signal strength Signal ID (up to 12 signals)

Center Frequency

Bandwidth

Signal Type (FM, GSM, W-CDMA, CDMA, Wi-Fi)

Closest Channel Number

Number of Carriers

Signal-to-Noise Ratio (SNR) > 10 dB Interference Mapping

Triangulate location of interference with on-display maps Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)

GPS Receiver Option (Option 0031) (Antenna sold separately)

Setup

GPS Time/Location Indicator

High Frequency Accuracy

Connector

On/Off, Antenna Voltage 3.3/5.0 V, GPS Info Time, Latitude, Longitude and Altitude on display

Time, Latitude, Longitude and Altitude with trace storage Spectrum Analyzer, Interference Analyzer, CW Signal Analyzers

< ± 50 ppb with GPS On, GPS antenna connected, 3 minutes after satellite lock in selected mode

SMA, Female

6 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

Channel Scanner (Option 0027)

Number of Channels

Measurements

Scanner

Amplitude

Custom Scan

Frequency Range

Frequency Accuracy

Measurement Range

Application Options

1 to 20 Channels Graph/Table, Max Hold (On/5 s/Off ), Freq/Channel, Current/Max, Single/Dual Color Scan Channels, Scan Frequencies, Scan Customer List, Scan Script Master™ Reference Level, Scale Signal Standard, Channel, # of Channels, Channel Step Size, Custom Scan 100 kHz to 4 GHz (MT8212E), 100 kHz to 6 GHz (MT8213E) ± 10 Hz + Time base error –110 dBm to +26 dBm Bias-Tee (On/Off), Impedance (50 Ω, 75 Ω, Other)

CW Signal Generator (Option 0028) (Requires CW Signal Generator Kit, P/N 69793)

Setup Parameters

Frequency

Amplitude

Frequency Range

Frequency Reference

Output Power

Frequency, Signal Standard, Channel Number, Display Setup Help Power Level (Low/High), Offset (dB) 2 MHz to 2 GHz Accuracy: ± 1.5 ppm (25 °C ± 25 °C) + aging, < ± 50 ppb with GPS On High 0 dBm typical, Low –30 dBm typical Attenuator (included in kit 69793): 0 to 90 dB in 1 dB steps

Gated Sweep (Option 0090)

Mode

Trigger

Setup

Spectrum Analyzer, Sweep External TTL Gated Sweep (On/Off) Gate Polarity (Rising, Falling) Gate Delay (0 ms to 65 ms typical)

Gate Length (1 Zero Span Time

s to 65 ms typical)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 7 of 32

Specifications Cell Master™ MT8212E and MT8213E

Power Meter

Frequency

Amplitude

Average

Limits

Frequency Range

Display Range

Measurement Range

Offset Range

VSWR

Maximum Continuous Input Power

Accuracy

Application Options

Center/Start/Stop, Span, Frequency Step, Signal Standard, Channel #, Full Band Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale Acquisition Fast/Med/Slow, # of Running Averages Limit On/Off, Limit Upper/Lower 10 MHz to 4 GHz (MT8212E), 10 MHz to 6 GHz (MT8213E)

Span

1 kHz to 100 MHz –140 dBm to +30 dBm, ≤ 40 dB span –120 dBm to +26 dBm 0 dB to +100 dB (External Gain or Loss) 2:1 typical +30 dBm Same as Spectrum Analyzer Impedance (50 Ω, 75 Ω, Other)

High Accuracy Power Meter (Option 0019) (Requires external USB Power Sensor(s))

Amplitude

Average

Zero/Cal

Limits

Power Sensor Model PSN50 MA24104A/05A MA24106A MA24108A/18A/26A

Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale # of Running Averages, Max Hold Zero On/Off, Cal Factor (Center Frequency, Signal Standard) Limit On/Off, Limit Upper/Lower

Description High Accuracy

Frequency Range 50 MHz to 6 GHz 600 MHz to 4 GHz

Connector Type N(m), 50

Dynamic Range –30 dBm to +20 dBm

VBW 100 Hz 100 Hz 100 Hz 50 kHz

Measurand True-RMS True-RMS True-RMS True-RMS, Slot Power,

Measurement Uncertainty ± 0.16 dB

(for complete specifications)

Notes:

1. Total RSS measurement uncertainty (0 ºC to 50 ºC) for power measurements of a CW signal greater than –20 dBm with zero mismatch errors.

2. Expanded uncertainty with K = 2 for power measurements of a CW signal greater than +20 dBm with a matched load. Measurement results referenced to the input side of the sensor.

3. Expanded uncertainty with K = 2 for power measurements of a CW signal greater than –20 dBm with zero mismatch errors.

Datasheet

RF Power

(0.001 mW to 100 mW)

Sensor

11410-00414 11410-00483

Inline Bi-Directional

Power Sensor

High

(MA24104A)

350 MHz to 4 GHz

(MA24105A)

Type N(m), 50

(MA24104A)

Type N(f), 50

(MA24105A)

+3 dBm to +51.76 dBm

(2 mW to 150 W)

± 0.17 dB

(MA24104A)

11410-00621

(MA24105A)

High Accuracy

RF Power

50 MHz to 6 GHz 10 MHz to 8 GHz

Type N(m), 50

–40 dBm to +23 dBm

(0.1 µW to 200 mW)

Sensor

± 0.16 dB

11410-00424 11410-00504

Microwave USB

Sensor

Power

(MA24108A)

10 MHz to 18 GHz

(MA24118A)

10 MHz to 26 GHz

(MA24126A)

Type N(m), 50

(MA24108A/18A)

Type K(m), 50

(MA24126A)

–40 dBm to +20 dBm

(0.1 µW to 100 mW)

Burst Average Power

± 0.18 dB

8 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

LTE Signal Analyzers (Options 0541, 0542, 0546, 055 1, 0552, 0556)

Measurements

(Option 0541 FDD) (Option 0551 TDD)

Channel Spectrum

Channel Power Occupied Bandwidth

Power vs. Time (TDD only)

Frame View Sub-Frame View Total Frame Power DwPTS Power Transmit Off Power Cell ID

Timing Error ACPR Spectral Emission Mask

Category A or B (Opt 1) RF Summary

Power vs. Resource Block (RB)

Constellation

Control Channel Power

Tx Time Alignment (FDD only) Modulation Summary

Antenna Icons

Demodulation (Option 0542 FDD) (Option 0552 TDD)

RB Power (PDSCH) Active RBs, Utilization %, Channel Power, Cell ID OSTP, Frame EVM by modulation

(FDD only)

QPSK, 16 QAM, 64 QAM Modulation Results

Ref Signal Power (RS) Sync Signal Power (SS) EVM – rms, peak, max hold Frequency Error – Hz, ppm Carrier Frequency Cell ID

Bar Graph or Table View RS, P-SS, S-SS PBCH, PCFICH PHICH, PDCCH (FDD only) Total Power (Table View) EVM (FDD only) Modulation Results

Includes EVM by modulation (FDD only)

Detects active antennas (1/2)

Over-the-Air (OTA)

(Option 0546 FDD)

(Option 0556 TDD)

Scanner

Cell ID (Group, Sector) S-SS Power, RSRP, RSRQ, SINR Dominance Modulation Results – On/Off

Tx Test

Scanner RS Power of MIMO antennas

Cell ID, Average Power Delta Power (Max-Min) Graph of Antenna Power Modulation Results – On/Off

Mapping

On-screen

S-SS Power, RSRP, RSRQ, or SINR

Scanner

Modulation Results – Off

Pass/Fail

(User Editable)

View Pass/Fail Limits

All, RF, Modulation

Available Measurements

Channel Power Occupied Bandwidth ACLR Frequency Error Carrier Frequency Dominance EVM peak, rms RS Power RS EVM (FDD only) SS, P-SS, S-SS Power SS, P-SS, S-SS EVM (FDD only) PBCH Power PBCH EVM (FDD only) PCFICH Power PCFICH EVM (FDD only) PHICH Power, EVM (FDD only) PDCCH Power, EVM (FDD only) Cell, Group, Sector ID OSTP (FDD only) Tx Time Alignment (FDD only) Frame Power (TDD only) DwPTS Power (TDD only) Transmit Off Power (TDD only) Timing Error (TDD only)

Setup Parameters

Frequency

Bandwidth

Amplitude

Sweep

EVM Mode

Save/Recall

Measurement Summary Screens

E-UTRA FDD bands 1 – 5, 7 – 14, 17 – 21, 23 – 25 (tunable 10 MHz to 4.0 GHz) E-UTRA TDD bands 33 – 43 (tunable 10 MHz to 4.0 GHz) Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel

1.4, 3, 5, 10, 15, 20 MHz

Span

Auto, 1.4, 3, 5, 10, 15, 20, 30 MHz Scale/Division, Power Offset, Auto Range, Adjust Range Single/Continuous, Trigger Sweep Auto, PBCH only Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Modulation Measurements

RF Measurements (Options 0541, 0551)

RF Channel Power Accuracy

± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +10 dBm) (Option 0541) ± 1.5 dB, ± 1.0 dB typical, (RF input –30 dBm to +10 dBm) (Option 0551)

Demodulation Measurements (Options 0542, 0552)

Frequency Error

Residual EVM (rms) (FDD only)

Residual EVM (rms) (TDD only)

± 10 Hz + time base error, 99 % confidence level

2.0% typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm) for BW ≤ 10 MHz

2.5% typical (E-UTRA Test Model 3.1, RF Input –50 dBm to +10 dBm) for BW > 10 MHz

2.0% typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm) for BW ≤ 10 MHz

2.5% typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm) for BW > 10 MHz

Over-the-Air (OTA) Measurements (Options 0546, 0556)

Scanner

Auto Save

Mapping

Six strongest signals if present Auto Save — Sync Signal Power and Modulation Results with GPS information

Scanner — three strongest signals if present RS Power — strongest signal

Map On-screen S-SS Power, RSRP, RSRQ, or SINR of Cell ID with strongest signal Scanner — three strongest signals if present Save and Export Scanner data: *.kml, *.mtd (tab delimited)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 9 of 32

Specifications Cell Master™ MT8212E and MT8213E

GSM/EDGE Signal Analyzers (Options 0040, 0041)

Measurements

(Option 0040)

Channel Spectrum

Channel Power Occupied Bandwidth Burst Power Average Burst Power Frequency Error Modulation Type

BSIC (NCC, BCC) Multi-channel Spectrum Power vs. Time (Frame/Slot)

Channel Power

Occupied Bandwidth

Burst Power

Average Burst Power

Frequency Error

Modulation Type

BSIC (NCC, BCC)

Phase Error EVM Origin Offset C/I Modulation Type Magnitude Error BSIC (NCC, BCC)

Setup Parameters

GSM/EDGE Select

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

RF Measurements (Option 0040) (Temperature range 15 ºC to 35 ºC)

Frequency Error

Occupied Bandwidth

Burst Power Error

Demodulation (Option 0041) (Temperature range 15 ºC to 35 ºC)

GSMK Modulation Quality (RMS Phase)

8 PSK Modulation Quality (EVM)

Measurement Accuracy

Residual Error (GSMK)

Measurement Accuracy

Residual Error (8 PSK)

Demodulation (Option 0041) Over-the-Air (OTA)

There are no additional OTA Measurements.

RF and Demodulation measurements can be made OTA

Auto, GSM, EDGE Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Power Offset, Auto Range, Adjust Range Single/Continuous, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements

± 10 Hz + time base error, 99 % confidence level Bandwidth within which 99 % of the power transmitted on a single channel lies ± 1.5 dB, ± 1 dB typical, (–50 dBm to +20 dBm)

± 1 deg 1 deg

± 1.5 %

2.5 %

Channel Power Occupied Bandwidth Burst Power Average Burst Power Frequency Error Phase Error EVM Origin Offset C/I Magnitude Error

Pass/Fail

(User Editable)

10 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

W-CDMA/HSPA+ Signal Analyzers (Options 0044, 0065, 0035)

Measurements

(Option 0044)

Band Spectrum Channel Spectrum

Channel Power Occupied Bandwidth

Peak-to-Average Power Spectral Emission Mask Single carrier ACLR Multi-carrier ACLR RF Summary

Code Domain Power Graph

Code Domain Power Table

Codogram Modulation Summary

Demodulation

(Option 0065)

P-CPICH Power Channel Power Noise Floor EVM Carrier Feed Through Peak Code Domain Error Carrier Frequency Frequency Error Control Channel Power Abs/Rel/Delta Power

CPICH, P-CCPCH S-CCPCH, PICH P-SCH, S-SCH

HSPA+

Power vs. Time Constellation

Code, Status EVM, Modulation Type Power, Code Utilization Power Amplifier Capacity

Over-the-Air (OTA)

(Option 0035)

Scrambling Code Scanner (Six)

Scrambling Codes CPICH E

C/IO

Pilot Dominance OTA Total Power

Multipath Scanner (Six)

Six Multipaths Tau Distance RSCP Relative Power Multipath Power

Pass/Fail

(User Editable)

Max Output Power Frequency Error EVM CPICH Occupied Bandwidth Spectral Mask ACLR PCDE P-CCPCH S-CCPCH Code Spread 3 PICH Code 128

Test M o d e ls

1 (16), (32), (64) 2 3 (16), (32) 4 (+CPICH), (–CIPCH) 5 (2 HS), (4 HS), (8 HS)

Setup Parameters

Scrambling Code, Threshold

User Selectable

Maximum Spreading Factor

Frequency

Amplitude

Marker

Sweep

Save/Recall

Measurement Summary Screens

Auto, Manual Scrambling Code, S-CCPCH Spread, S-CCPCH Code, PICH Code, Threshold, Max Amp Power, CPICH Power,

Frequency Error Average 256, 512 Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Scale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/Watts) Six Markers, Table On/Off Single/Continuous, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Signal Quality Measurements

RF Measurements (Option 0044) (temperature range 15 °C to 35 °C)

Frequency Range

RF Channel Power Accuracy

Occupied Bandwidth Accuracy

Adjacent Channel Leakage Ratio (ACLR)

Bands I – XIV, XVII ± 1.25 dB, ± 0.7 dB typical, (Temperature range 15 ºC to 35 ºC) ± 100 kHz –54 dB/–59 dB ± 0.8 dB @ 5 MHz/10 MHz offset, typical, Bands I – VI, VIII – XIV, XVII –54 dB/–57 dB ± 1.0 dB @ 5 MHz/10 MHz offset, typical, Band VII

Demodulation (Option 0065) (temperature range 15 ºC to 35 ºC)

Frequency Error

W-CDMA Modulations

HSPA+ Modulations

EVM Accuracy

Residual EVM

Code Domain Power

CPICH (dBm) Accuracy

± 10 Hz + time base error, 99% confidence level QPSK, QPSK-DTX (Codecs: AMR 4.75, 5.9, 7.4, 12.2 kbps, DTX 7.4, 12.2 kbps) QPSK, 16 QAM, 64 QAM ± 2.5 %, 6% ≤ EVM ≤ 25%

3.25% typical ± 0.5 dB for code channel power > –25 dB, 16, 32, 64 DCPH (test model 1), 16, 32 DCPH (test model 2, 3) ± 0.8 dB typical

Over-the-Air (OTA) Measurements (Option 0035)

Scrambling Code Scanner

Multipath Scanner

Six strongest Scrambling Codes Multipath power of six signals relative to strongest pilot

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 11 of 32

Specifications Cell Master™ MT8212E and MT8213E

CDMA Signal Analyzers (Options 0042, 0043, 0033)

Measurements

(Option 0042)

Channel Spectrum

Channel Power Occupied Bandwidth

Peak-to-Average Power Spectral Emission Mask Multi-carrier ACPR RF Summary

Code Domain Power Graph

Code Domain Power Table

Modulation Summary

Demodulation (Option 0043)

Pilot Power Channel Power Noise Floor Rho Carrier Feed Through Tau RMS Phase Error Frequency Error Abs/Rel/ Power

Pilot Page Sync Q Page

Code Status Power Multiple Codes Code Utilization

Over-the-Air (OTA)

(Option 0033)

Pilot Scanner (Nine)

PN E

C/IO

Tau Pilot Power Channel Power Pilot Dominance

Multipath Scanner (Six)

C/IO

Tau Channel Power Multipath Power

Limit Test – 10 Tests Averaged

Rho Adjusted Rho Multipath Pilot Dominance Pilot Power Pass/Fail Status

Pass/Fail

(User Editable)

Channel Power Occupied Bandwidth Peak-to-Average Power Spectral Mask Test Frequency Error Channel Frequency Pilot Power Noise Floor Rho Carrier Feed Through Tau RMS Phase Error Code Utilization Measured PN Pilot Dominance Multipath Power

Setup Parameters

PN Setup

Walsh Codes

Measurement Speed

External Trigger Polarity

Number of Carriers

Carrier Bandwidth

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

PN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset 64, 128 Fast, Normal, Slow Rising, Falling 1 to 5

1.23, 1.24, 1.25 MHz Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Scale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/Watts) Single/Continuous, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Signal Quality Measurements

RF Measurements (Option 0042) (Temperature range 15 ºC to 35 ºC)

RF Channel Power Accuracy

± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +20 dBm)

Demodulation (Option 0043) (Temperature range 15 ºC to 35 ºC)

Frequency Error

Rho Accuracy

Residual Rho

PN Offset

Pilot Power Accuracy

± 10 Hz + time base error, 99 % confidence level (in slow mode) ± 0.005, for Rho > 0.9 > 0.995, typical, > 0.99 maximum, (RF input –50 dBm to +20 dBm) 1 x 64 chips ± 1.0 dB typical, relative to channel power

Tau

± 0.5 µs typical, ± 1.0 µs maximum

Over-the-Air (OTA) Measurements (Option 0033)

Pilot Scanner

Multipath Scanner

Limit Test

Nine strongest pilots Multipath power of six signals relative to strongest pilot Average of ten tests compared to limit

12 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

EV-DO Signal Analyzers (Options 0062, 0063, 0034)

Measurements

(Option 0062)

Channel Spectrum

Channel Power Occupied Bandwidth Peak-to-Average Power

Power vs. Time

Pilot & MAC Power Channel Power Frequency Error Idle Activity

On/Off Ratio Spectral Emission Mask Multi-carrier ACPR RF Summary

MAC Code Domain Power Graph

MAC Code Domain Power Table

Data Code Domain Power

Modulation Summary

Demodulation

(Option 0063)

Pilot & MAC Power Channel Power Frequency Error Rho Pilot Rho Overall Data Modulation Noise Floor

Code Status Power Code Utilization

Active Data Power Data Modulation Rho Pilot Rho Overall Maximum Data CDP Minimum Data CDP

Over-the-Air (OTA)

(Option 0034)

Pilot Scanner (Nine)

PN E

C/IO

Tau Pilot Power Channel Power Pilot Dominance

Multipath Scanner (Six)

C/IO

Tau Channel Power Multipath Power

Pass/Fail

(User Editable)

Channel Power Occupied Bandwidth Peak-to-Average Power Carrier Frequency Frequency Error Spectral Mask Noise Floor Pilot Power RMS Phase Error Tau Code Utilization Measured PN Pilot Dominance Multipath Power

Setup Parameters

PN Setup

Wals h Codes

Measurement Speed

External Trigger Polarity

Slot Type

Number of Carriers

Carrier Bandwidth

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

PN Trigger (No Trigger, GPS, External), PN Search Type (Auto, Manual), PN Offset 64, 128 Fast, Normal, Slow Rising, Falling Auto, Active, Idle 1 to 5

RF Measurements (Option 0062) (Temperature range 15 ºC to 35 ºC)

RF Channel Power Accuracy

± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +20 dBm)

Demodulation (Option 0063) (Temperature range 15 ºC to 35 ºC)

EV-DO Compatibility

Frequency Error

Rho Accuracy

Residual Rho

PN Offset

Pilot Power Accuracy

Rev 0 and Rev A ± 10 Hz + time base error, 99 % confidence level ± 0.01, for Rho > 0.9 > 0.995 typical, > 0.99, maximum (RF input –50 dBm to +20 dBm) Within 1 x 64 chips ± 1.0 dB typical, relative to channel power

Tau

± 0.5 µs typical, ±1.0 µs maximum

Over-the-Air (OTA) Measurements (Option 0034)

Pilot Scanner

Multipath Scanner

Nine strongest pilots Multipath power of six signals relative to strongest pilot

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 13 of 32

Specifications Cell Master™ MT8212E and MT8213E

Fixed WiMAX Signal Analyzers (Options 0046, 0047)

Measurements

(Option 0046)

Channel Spectrum

Channel Power Occupied Bandwidth

Power vs. Time

Channel Power Preamble Power Data Burst Power

Crest Factor ACPR RF Summary

Constellation

Spectral Flatness

EVM vs. Subcarrier/Symbol

Modulation Summary

Setup Parameters

Bandwidth

Cyclic Prefix Ratio (CP)

Span

Frame Length

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

RF Measurements (Option 0046) (Temperature range 15 ºC to 35 ºC)

RF Channel Power Accuracy

Demodulation (Option 0047) (Temperature range 15 ºC to 35 ºC)

Frequency Error

Residual EVM (rms)

Demodulation (Option 0047) Over-the-Air (OTA)

There are no additional OTA RCE (RMS/Peak) EVM (RMS/Peak) Frequency Error Carrier Frequency Base Station ID

Adjacent Subcarrier Flatness

RCE EVM Frequency Error Carrier Frequency Base Station ID

1.25, 1.50, 2.50, 3.50, 5.00, 5.50, 6.00, 7.00, 10.00 MHz 1/4, 1/8, 1/16, 1/32 5, 10, 15, 20 MHz

2.5, 5.0, 10.0 ms Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Scale/Division, Power Offset, Auto Range, Adjust Range Single/Continuous, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Signal Quality Measurements

± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +20 dBm)

0.07 ppm + time base error, 99 % confidence level 3 % typical, 3.5 % maximum (RF Input –50 dBm to +20 dBm)

Measurements.

RF and Demodulation

measurements can be made OTA

Channel Power Occupied Bandwidth Burst Power Preamble Power Crest Factor Frequency Error Carrier Frequency EVM RCE Base Station ID

Pass/Fail

(User Editable)

14 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

Mobile WiMAX* Signal Analyzers (Options 0066, 0067, 0037)

Measurements

(Option 0066)

Channel Spectrum

Channel Power Occupied Bandwidth

Power vs. Time

Channel Power Preamble Power Downlink Burst Power

Uplink Burst Power ACPR RF Summary

Constellation

Spectral Flatness

EVM vs. Subcarrier/Symbol

DL-MAP (Tree View) Modulation Summary

Setup Parameters

Zone Type

DL-MAP Auto Decoding

Bandwidths

Cyclic Prefix Ratio (CP)

Span

Frame Lengths

Demodulation

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

RF Measurements (Option 0066) (Temperature range 15 ºC to 35 ºC)

RF Channel Power Accuracy

Demodulation (Option 0067) (Temperature range 15 ºC to 35 ºC)

Frequency Error

Residual EVM (rms)

Over-the-Air (OTA) Measurements (Option 0037)

Channel Power Monitor

Preamble Scanner

Auto Save

GPS Logging

Demodulation

(Option 0067)

RCE (RMS/Peak) EVM (RMS/Peak) Frequency Error CINR Base Station ID Sector ID

Adjacent Subcarrier Flatness

RCE (RMS/Peak) EVM (RMS/Peak) Frequency Error CINR Base Station ID Sector ID

PUSC Convolutional Coding (CC), Convolutional Turbo Coding (CTC)

3.50, 5.00, 7.00, 8.75, 10.00 MHz 1/8 5, 10, 20, 30 MHz 5, 10 ms Auto, Manual, FCH Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Scale/Division, Power Offset, Auto Range, Adjust Range Single/Continuous, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Signal Quality Measurements

± 1.5 dB, ± 1.0 dB typical, (RF input –50 dBm to +20 dBm)

0.02 ppm + time base error, 99 % confidence level

2.5 % typical, 3.0 % maximum, (RF Input –50 dBm to +20 dBm)

Over time (one week), measurement time interval 1 to 60 s Six Strongest Preambles Yes Yes

Over-the-Air (OTA)

(Option 0037)

Channel Power Monitor Preamble Scanner (Six)

Preamble Relative Power Cell ID Sector ID PCINR Dominant Preamble

Base Station ID

Channel Power Occupied Bandwidth Downlink Bust Power Uplink Burst Power Preamble Power Crest Factor Frequency Error Carrier Frequency EVM RCE Sector ID

Pass/Fail

(User Editable)

*Conforms to IEEE Std. 802.16e-2005, WiMAX Forum® Air Interface - Mobile System Profile - Release 1.0 Certified, System Profiles

according to WMF-T24-001-R010v07.

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 15 of 32

Specifications Cell Master™ MT8212E and MT8213E

TD-SCDMA/HSPA+ Signal Analyzers (Options 0060, 0061, 0038)

Measurements

(Option 0060)

Channel Spectrum

Channel Power Occupied Bandwidth Left Channel Power Left Channel Occ B/W Right Channel Power Right Channel Occ B/W

Power vs. Time

Six Slot Powers Channel Power (RRC) DL-UL Delta Power UpPTS Power DwPTS Power On/Off Ratio

Slot Peak-to-Average Power Spectral Emission RF Summary

Code Domain Power/Error

Modulation Summary

Setup Parameters

Slot Selection

Tri gger

SYNC-DL Code

Scrambling/Midamble Code

Maximum Users

Measurement Speed

User Selectable

Demodulation Type

Frequency

Amplitude

Sweep

Save/Recall

Measurement Summary Screens

RF Measurements (Option 0060) (Temperature range 15 ºC to 35 ºC)

RF Channel Power Accuracy (RRC)

Frequency Error

Demodulation (Option 0061) (Temperature range 15 ºC to 35 ºC)

Supported Demodulation

Residual EVM (rms)

PN Offset

Pilot Power Accuracy

Timing Error (Tau) for Dominant

SYNC-DL

Spreading Factor

Over-the-Air (OTA) Measurements (Option 0038)

Code Scanner

Tau S c a nne r

Auto Save

GPS Logging

Demodulation (Option 0061)

(QPSK/8 PSK/16 QAM) Slot Power DwPTS Power Noise Floor Frequency Error Tau Scrambling Code EVM Peak EVM Peak Code Domain Error

Auto, 0-6 Trigger Type (No Trigger/GPS/External), External Trigger (Rising/Falling), Tau Offset Auto, 0 – 31 Auto, 0 – 127 Auto, 2, 4, 6, 8, 10, 12, 14, 16 Fast, Normal, Slow Uplink Switch Point, Number of Carriers (1, 3), Tau Offset Auto, QPSK, 8 PSK, 16 QAM Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel Scale/Division, Power Offset, Auto Range, Adjust Range, Units (dBm/Watts) Hold/Run, Trigger Sweep Setup, Measurement, Screen Shot (save only), to Internal/External Memory Overall Measurements, RF Measurements, Signal Quality Measurements

± 1.5 dB, ±1.0 dB typical, (slot power –40 dBm to +10 dBm) ±10 Hz + time base error, in the presence of a downlink slot

QPSK, 8 PSK, 16 QAM 3% typical, P-CCPH slot power > –50 dBm Within 1 x 64 chips ± 1.0 dB typical

± 0.2 μs (external trigger) 1, 16

32 Sync Codes and associated Scrambling Code Groups Six strongest Sync Codes Yes Yes

Over-the-Air (OTA)

(Option 0038)

Code Scan (32)

Scrambling Code Group Tau E

C/IO

Pilot Dominance

Tau S c a n (S i x )

Sync-DL# Tau E

C/IO

DwPTS Power Pilot Dominance

Occupied Bandwidth Channel Power Channel Power RCC On/Off Ratio Peak-to-Average Ratio Frequency Error EVM Peak EVM Peak Code Domain Error Tau Noise Floor

Pass/Fail

(User Editable)

16 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

ISDB-T Measurements (Options 0030, 0079, 0032)

For full specifications refer to the Digital Broadcast Analysis Options Technical Data Sheet 11410-00624

Measurements

ISDB-T RF

(Option 0030)

Signal Power

Channel Power Termination Voltage Open Terminal Voltage Field Strength

Spectrum Monitor

Channel Power Zone Center Channel Zone Center Frequency

Spectrum Mask

Mask (Standard A) Japan Mask (Standard B) Japan Mask (Critical) Brazil Mask (Sub-critical) Brazil

Mask (Non-critical) Brazil Phase Noise Spurious Emissions

ISDB-T Measurement Modes

Custom: User specified measurement and setup parameters Easy: User specified measurements. Some setup parameters are automatically set or detected Batch: User specified measurements and channels for automatic measurement, results' display and storage

ISDB-T Signal Analysis

(Option 0030)

Constellation (w/zoom)

Layer A, B, C, TMCC Sub-carrier MER Delay Profile (w/zoom) Frequency Response Measured Data

Frequency

Frequency Offset

MER (Total, Layer A/B/C, TMCC,

AC1)

Modulation (Layer A/B/C)

Mode, GI

Sub-carrier MER w/marker

Delay w/marker

Frequency Response w/marker

ISDB-T BER Analysis

(Option 0079)

Layer A, Layer B, Layer C BER and Error Count per Layer

Before RS

Before Viterbi PER and Error Count per Layer MPEG Bit Rate per Layer TMCC Information per Layer

Modulation

Code Rate

Interleave

Segments Channel Power Mode, GI Signal Sync Status ASI Out

ISDB-T SFN Analysis

(Option 0032)

Impulse Response (w/zoom) In-band Spectrum Measured Data

Channel Power Delay DU Ratio Power Field Strength

Setup Parameters

Channel Map

Channel

Frequency

Bandwidths

Partial Reception

One-Seg

Pre-amp

Reference Level Setting

UHF (Japan), UHF (Brazil), IF (37.15 MHz), None 13 to 62 (Japan), 14 to 69 (Brazil) 35 MHz to 806 MHz 6 MHz, 8 MHz Recognized when layer A segment count is 1 On: synchronizes with single segment transmission (Bandwidth 6 MHz only)

Off: synchronizes with normal 13 segment signal On, Off –25 dBm to +20 dBm/5 dB steps (Preamp Off), –50 dBm to –10 dBm/10 dB steps (Preamp On)

ISDB-T Digital Video Measurements (Option 0030)

Channel Power Accuracy

Frequency Lock Range

Frequency Offset Accuracy

Residual MER≥ 42 dB, typical (Preamp Off, Reference level: –20 dBm)

Sub-carrier MER Display Range

Delay Profile Resolution

Frequency Response Resolution

Phase Noise Range

Spurious Emissions Search Range

ISDB-T BER Measurements (Option 0079)

BER Measurement Display per Layer PER Measurement Display per Layer TMCC Information Display per Layer

ASI Output

± 2 dB, (RF input –84 dBm to –10 dBm) ± 90 kHz ± (measurement frequency x reference frequency accuracy) ± 0.3 Hz

≥

37 dB, typical (Preamp On, Reference level: –50 dBm)

± 2.785 MHz from center frequency (Bandwidth 6 MHz) ± 3.714 MHz from center frequency (Bandwidth 8 MHz)

0.12 µs (Bandwidth 6 MHz)

0.09 µs (Bandwidth 8 MHz) 1 kHz, 0.1 dB –40 dBc/Hz to –140 dBc/Hz 5 MHz to 5x input signal frequency

(Operating temperature range 0 ºC to 40 ºC)

Rate and Error count: Before Viterbi, Before RS Rate and Error count Modulation, Code Rate, Interleave, Number of segments BNC-J 75

ISDB-T SFN Measurements (Option 0032)

Delay Profile Display Range

Delay Wave Estimated Level Accuracy

DU Ratio Accuracy

Inband Spectrum Range

–1008 µs to +1008 µs (Bandwidth 8 MHz) ± 2.5 dB typical (–10 dBm to –79 dBm) ± 1 dB typical (–10 dBm to –70 dBm) ± 2.74 MHz (Mode 2), ± 2.76 MHz (Mode 3) (Bandwidth 8 MHz)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 17 of 32

Specifications Cell Master™ MT8212E and MT8213E

DVB-T/H (Options 0064, 0057, 0078)

For full specifications refer to the Digital Broadcast Analysis Options Technical Data Sheet 11410-00624

Measurements

DVB-T/H RF

(Option 0064)

Signal Power

Channel Power Termination Voltage Open Terminal Voltage Field Strength

Spectrum Monitor

Channel Power Zone Center Channel Zone Center Frequency

Shoulder Attenuation

Channel Power Zone Center Channel Zone Center Frequency Lower Shoulder Attenuation Upper Shoulder Attenuation

DVB-T/H Signal Analysis

(Option 0064)

Composite or Individual Views

Constellation Impulse Response (w/zoom) Carrier MER (w/zoom) Freq Response (composite view

only)

Measured Data

Mode, GI Modulation Hierarchy Freq Offset Channel Power MER (Total/Data/TPS) TPS Warning Message TPS Info Interleave Type Cell ID Code Rate (HP/LP) Time Slicing (HP/LP) MPE-FEC (HP/LP)

DVB-T/H BER Analysis

(Option 0057)

BER

Before RS

Before Viterbi PER (Packet) Channel Power MER (Quick) Bit Rate TPS Info

Length Indicator

Mode, GI

Modulation

Hierarchy

Interleave Type

Cell ID

Code Rate

Time Slicing

MPE-FEC TPS Warning Message ASI Out

DVB-T/H SFN Analysis

(Option 0078)

Impulse Response (w/zoom) Inband Spectrum Measured Data

Channel Power Delay DU Ratio Power Field Strength

Setup Parameters

Channel Map

Channel

Frequency Offset

Frequency

Bandwidth

Pre-amp

Reference Level

UHF (Australia), UHF (Europe), VHF (Europe), None 28 to 69 (Australia), 21 to 69 (Europe), 5 to 12 (Europe) ± 166.666 kHz, ± 333.333 kHz, ± 499.999 kHz, None 30 MHz to 2.8 GHz when Channel Map is None 5*, 6*, 7, 8 MHz On, Off –25 dBm to +20 dBm/5 dB steps (Preamp Off), –50 dBm to –10 dBm/10 dB steps (Preamp On)

DVB-T/H Digital Video Measurements (Option 0064)

Channel Power Accuracy

Frequency Lock Range

Frequency Offset Accuracy

Residual MER≥ 42 dB (Preamp Off, Reference Level: –20 dBm)

Impulse Response Resolution

Carrier MER Marker

Composite View

DVB-T/H BER Measurements (Option 0057)

Bit Count Setting

Service Type

TPS Information

ASI Output

± 2 dB, (RF input –84 dBm to –10 dBm) ± 90 kHz ± (measurement frequency x reference frequency accuracy) ± 0.3 Hz

≥

37 dB (Preamp On, Reference Level: –50 dBm)

0.11 µs (Bandwidth: 8 MHz), 0.1 dB Carrier Number, Offset Frequency and MER Simultaneous display of Constellation (Data and TPS), Impulse Response, Carrier MER and Frequency

Response

(Operating temperature range 0 ºC to 40 ºC)

Range 1E+6 to 1E+12 In Service: BER measurement of normal in-service data traffic Simultaneous BER measurement Before Viterbi and Before RS error correction

Out of Service: BER measurement of a PRBS23 data sequence BER measurement point can be selected Before Viterbi, Before RS or After RS Length indicator, Mode, GI, Modulation, Hierarchy, Inner Interleave, Cell ID, Code Rate, Time Slicing,

MPE-FEC BNC-J 75

DVB-T/H SFN Measurements (Option 0078)

Impulse Response Display Range

Resolution

Marker

Inband Spectrum Range

–896 µs to +896 µs (Bandwidth 8 MHz)

0.11 µs (33 m) (Bandwidth 8 MHz) Delay time, relative level (DU ratio), power and field strength or termination voltage ± 3.804 MHz (Bandwidth 8 MHz)

*Not available for BER measurements

18 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Specifications

Backhaul Analyzers (Options 0051, 0052, 0053)

T1 Bit-Error-Rate Tester (BERT) (Option 0051)

Measurements

Error Detection

Error Analysis (ITU G-821)

Rx Signal

Status (Historical and Current)

Status (Current)

Setup

BERT Display

Line Code

Tx Clock

Tx LBO

Rx Input

Framing

Payload

Pulse Shapes

Patterns

Loop Codes

Error Insertion

Alarm Insertion

Data Log

E1 Bit-Error-Rate Tester (BERT) (Option 0052)

Measurements

Error Detection

Error Analysis (ITU G-821)

Rx Signal

Status (Historical and Current)

Status (Current)

Setup

BERT Display

Line Code

Tx Clock

Rx Input

Framing

Payload

Pulse Shapes

Patterns

Loopback Mode

Error Insertion

Alarm Insertion

Data Log

Frame Bits, Bit Errors, BER, BPV, CRC, PATLS Errored Seconds (ES), Error Free Seconds (EFS), Severely Errored Seconds (SES), Unavailable Seconds

(UAS), Available Seconds (AS), Degraded Minutes (DGRM) Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx, Clock Slips, Frame Slips

Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (–40.0 dBm to +3.0 dBm, ± 0.2 dBm) Rx (Signal, Frame Sync, Pattern Sync), DS1 (Alarms, Errors, B8ZS) Tx (Alarm On, Error On, Loop On)

Table, Histogram, Event List, Clear History

Tx (Off/On), Channel (1-24), Tx Freq, Tx Level (–30 dBm to 0 dBm), Volume, Audio, Clear AMI, B8ZS Internal (1.544 MHz ± 5 ppm), Recovered, External

0.0 dB, –7.5 dB, –15.0 dB Terminate (Bantam connector 100 Ω balanced)

Monitor (Connect via 20 dB pad in DSX, 20 dB flat gain)

≥

Bridge ( ESF, SF-D4 T1 (1.544 Mbps), Fractional T1 (Nx64, 64, 56, 16, 8 kbps) Conform to ANSI T1.403 and ITU G.703 QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1-in-8 (1-in-7), 2-in-8, 3-in-24 T1 Daly,

Six User defined ( CSU, NIU, Link Type (In-Band, Data-Link), Self Loop Up/Down, Loop Code User Defined Bit Error, Bit Error Rate (BER), BPV, Frame Bit Error, Error (On/Off) AIS On/Off (Blue Alarm), RAI On/Off (Yellow Alarm) 1 minute to 3 days

Frame Bits, Bit Errors, BER, BPV, CRC, E Bits Errored Seconds (ES), Error Free Seconds (EFS), Severely Errored Seconds (SES),

Unavailable Seconds (UAS), Available Seconds (AS), Degraded Minutes (DGRM) Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx, Clock Slips, Frame Slips

Frequency (100 Hz to 3000 Hz), Power (–40.0 dBm to +3.0 dBm, ± 0.2 dBm) Rx (Signal, FAS, Pattern Sync), E1 (Alarms, Errors) Tx (Alarm On, Error On)

Table, Histogram, Event List, Clear History

Tx (Off/On), Channel (1 to 31), Tx Freq, Tx Level (–30 dBm to 0 dBm), Volume, Audio, Clear AMI, HDB3 Internal (2.048 MHz ± 5 ppm), Recovered, External Terminate (RJ48 120/75 Ω balanced, BNC 75 Ω unbalanced, –43 dB to +6 dB), Bridge (

Monitor (Connect via 20 dB pad in DSX, 20 dB flat gain) PCM30, PCM30 CRC-4, PCM31, PCM31 CRC-4 E1 (2.048 Mbps), Fractional E1 (N x 64, 64, 16, 8 kbps) Conform to ITU G.703 QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1010, 1-in-8 (1-in-7), 2-in-8, 3-in-24,

Six User defined ( Self loop Bit Error, Bit Error Rate (BER), Frame Bit Error, Error (On/Off) AIS (On/Off) (Blue Alarm), RAI (On/Off) (Yellow Alarm) 1 minute to 3 days

1000 Ω, –36 dB to +6 dB)

≤

32 bits), Inverse Patterns (On/Off), Remote Loop Up/Down

≥

1000 Ω, –43 dB to +6 dB)

≤

32 bits), Inverse Patterns (On/Off)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 19 of 32

Specifications Cell Master™ MT8212E and MT8213E

Backhaul Analyzers (Options 0051, 0052, 0053)

T3 Bit-Error-Rate Tester (BERT) (Option 0053)

Measurements

Error Detection

Error Analysis (ITU G-821)

Rx Signal

Status (Historical and Current)

Status (Current)

Setup

BERT Display

Line Code

Tx Clock

Tx LBO

Rx Input

Framing

Test Mode

Pulse Shapes

Patterns

Loop Codes

Error Insertion

Alarm Insertion

Data Log

DS1 Test Mode

Measurements

Error Detection

Error Analysis (ITU G-821)

Rx Signal

Status (Historical and Current)

Status (Current)

Setup

BERT Display

Line Code

Tx Clock

Tx LBO

Rx Input

Framing

Payload

Pulse Shapes

Patterns

Loopback Mode

Error Insertion

Alarm Insertion

Data Log

Frame Bits, Bit Errors, BER, BPV, Lof Count, P-bit Errors, C-bit Errors, FEBE Errors Excess Zeros, Errored Seconds (ES), Error Free Seconds (EFS), Severely Errored Seconds (SES),

Unavailable Seconds (UAS), Available Seconds (AS), Degraded Minutes (DGRM), Pattern Loss Seconds (PATLS)

Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx

Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (–30.0 dBm to +0.0 dBm, ± 0.2 dBm) Rx (Signal, Frame Sync, Pattern Sync), DS3 (Alarms, Errors, DS3ZS) Insert (Alarm On, Error On, Loop On)

Table, Histogram, Event List, Clear History

Tx (Off/On), Channel #, Tx Freq, Tx, Level, Volume, Audio (On/Off ) AMI, B3ZS Internal (44.736 MHz ± 5 ppm), Recovered Low, DSX DSX3 (Bantam connector 100 Ω balanced) Monitor (Connect via 20 dB pad in DSX) M13, C-Bit, Unframed Auto, DS3, DS1 Carrier present, Frame ID and Sync, Pattern ID and Sync QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1010,1-in-8 (1-in-7), 2-in-8,

3-in-24 T1 Daly, Six User defined ( Stuff Bit, DS3 C-Bit FEAC, DS3 Self Loop Bit Error, BPV, DS3 Frame Bit Error, C-bit, P-bit, FEBE, Error Insert (On/Off) AIS (Blue Alarm), RAI (Yellow Alarm), Idle Alarm, Alarm (On/Off) 1 minute to 3 days

Frame Bits, Bit Errors, BER, BPV, CRC, PATLS Errored Seconds (ES), Error Free Seconds (EFS), Severely Errored Seconds (SES),

Unavailable Seconds (UAS), Available Seconds (AS), Degraded Minutes (DGRM) Frequency (± 5 ppm, Max/Min), Vpp (± 5%) (Max/Min), dBdsx, Clock Slips, Frame Slips

Frequency (100 Hz to 3000 Hz, ± 3 Hz), Power (–40.0 dBm to +3.0 dBm, ± 0.2 dBm) Rx (Signal, Frame Sync, Pattern Sync), DS1 (Alarms, Errors, B8ZS) Tx (Alarm On, Error On, Loop On)

Table, Histogram, Event List, Clear History

Tx (Off/On), Channel (1 to 24), Tx Freq, Tx Level (–30 dBm to 0 dBm), Volume, Audio, Clear AMI, B8ZS Internal (1.544 MHz ± 5 ppm), Recovered, External

0.0 dB, –7.5 dB, –15.0 dB Terminate (Bantam connector 100 Ω balanced) Monitor (Connect via 20 dB pad in DSX, 20 dB flat gain)

Bridge (

≥

1000 Ω, –36 dB to +6 dB) ESF, SF-D4 T1 (1.544 Mbps), Fractional T1 (Nx64, 64, 56, 16, 8 kbps) Conform to ANSI T1.403 and ITU G.703 QRSS, PRBS (2-9, 2-11, 2-15, 2-20, 2-23), All Ones, All Zeros, 1-in-8 (1-in-7), 2-in-8, 3-in-24 T1 Daly,

≤

32 bits), Inverse Patterns (On/Off), Remote Loop Up/Down

≤

32 bits), Inverse Patterns (On/Off), Loop Up/Down

(Continued)

20 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E General Specifications

General Specifications

All specifications and characteristics apply under the following conditions, unless otherwise stated: 1) After 5 minutes of warm-up time, where the instrument is left in the ON state; 2) All specifications apply when using internal reference; 3) All specifications subject to change without notice; 4) Typical performance is the measured performance of an average unit and is not warranted; 5) Recommended calibration cycle is 12 months; 6) Performance Sweep Mode.

Setup Parameters

System

System Options

Save/Recall

Delete

Directory Management

Internal Trace/Setup Memory

External Trace/Setup Memory

Mode Switching

Connectors

RF Out

RF Out Damage Level

RF Input Damage Level

ASI Output Connector

External Power

USB Interface (2)

USB Interface

Headset Jack

External Reference In

External Trigger/Clock Recovery

Display

Resolution

Pixel Defects

Battery

Battery Operation

Electromagnetic Compatibility

European Union

Australia and New Zealand

Interference

Emissions

Immunity

Safety

Safety Class

Product Safety

Environmental

Operating Temperature

Maximum Humidity

Shock Storage Altitude

ESD

RF Port Center Pin

File

RF In

GPS

T1 T3 E1

Type

Size

Type

Status (Temperature, Battery Info, Serial Number, Firmware Version, Options Installed) Self Test, Application Self Test, GPS (see Option 0031) Name, Date and Time, Brightness, Volume Language (English, French, German, Spanish, Chinese, Japanese, Korean, Italian, User defined) Reset (Factory Defaults, Master Reset, Update Firmware) Save, Recall, Delete, Directory Management Setups, Measurements, Screen Shots (.jpg) (save only)

Selected File, All Measurements, All Mode Files, All Content Sort Method (Name/Type/Date), Ascend/Descend, Internal/USB, Copy, Format USB 2,000 traces, 2,000 setups Limited by size of USB Flash drive Auto-Stores/Recalls most recently used Setup Parameters in the Mode

Type N, female, 50 Ω (Reflection In) 23 dBm, ± 50 VDC Type N, female, 50 +33 dBm peak, ± 50 VDC, Maximum Continuous Input (≥ 10 dB attenuation) BNC-J 75 Ω (with Option 0057 or Option 0079) SMA(f) Bantam jacks BNC connectors RJ48C

5.5 mm barrel connector, 12.5 VDC to 15 VDC, < 4.0 Amps Type A (Connect USB Flash Drive and Power Sensor) 5-pin mini-B (Connect to PC for data transfer and/or remote control)

3.5 mm mini-phone plug BNC, female, 50 Ω, Maximum Input +10 dBm, 1 MHz, 5 MHz, 10 MHz, 13 MHz BNC, female, 50 Ω, Maximum Input ± 50 VDC

Resistive Touchscreen

8.4" daylight viewable color LCD 800 x 600 No more than one defective pixel (99.9997% good pixels)

Li-Ion

3.0 hours, typical

CE Mark, EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC C-tick N274

EN 61326-1 EN 55011 EN 61000-4-2/-4-3/-4-4/-4-5/-4-6/-4-11

EN 61010-1 Class 1 IEC 60950-1 when used with Company supplied Power Supply

–10 ºC to 55 ºC 95% RH (non-condensing) at 40 ºC MIL-PRF-28800F Class 2 –40 ºC to 71 ºC 4600 meters, operating and non-operating

Withstands up to ± 15 kV

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 21 of 32

Size and Weight

Size

Weig ht

273 mm x 199 mm x 91 mm (10.7 in x 7.8 in x 3.6 in)

3.71 kg, (8.2 lbs)

2-22 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Software Cell Master™ MT8212E and MT8213E

Line Sweep Tools (for your PC)

Trace Capture

Browse to Instrument

Open Legacy Files

Open Current Files

Capture Plots To

View and copy traces from the test equipment to your PC using Windows Explorer Open DAT files captured with Hand Held Software Tools v6.61 Open VNA or DAT files The Line Sweep Tools screen, DAT files, Database, or JPEG

Traces

Tra c e Ty p e s

Trace Formats

Return Loss, VSWR, DTF-RL, DTF-VSWR, Cable Loss, Smith Chart, and PIM DAT, VNA, CSV, PNG, BMP, JPG, HTML, Data Base, and PDF

Report Generation

Report Generator

Report Format

Report Setup

Tra c e S e t u p

Includes GPS location along with measurements Create reports in HTML or PDF format Report Title, Company, Prepared for, Location, Date and Time, Filename, Company logo 1 Trace Portrait Mode, 2 Trace Portrait Mode, 1 Trace Landscape Mode

Trace Validation

Presets

Marker Controls

Delta Markers

Limit Line

Next Trace Button

7 presets allow “one click” setting of up to 6 markers and one limit line 6 regular Markers, Marker Peak, Marker Valley, Marker between, and frequency entry 6 Delta markers Enable and drag or value entry. Also works with presets Next Trace and Previous trace arrow keys allow quick switching between traces

Tools

Cable Editor

Distance to Fault

Measurement Calculator

Signal Standard Editor

Renaming Grid

Allows creation of custom cable parameters Converts a Return Loss trace to a Distance to Fault trace Converts Real, Imaginary, Magnitude, Phase, RL, VSWR, Rho, and Transmit power Creates new band and channel tables 36 user definable phrases for creation of file names, trace titles, and trace subtitles

Connectivity

Connections

USB cable, USB Memory Stick

easyTest Tools (for your PC)

Instrument Mode

Cable & Antenna Analyzer Mode

Commands

Display Image

Recall Setup

Prompt

Allows putting a custom image on the instrument screen Places the instrument into a known state Displays instructional messages on the instrument screen

Save

Allows automatic or manual saving of traces

Connectivity

Connections

USB cable or USB memory stick

Master Software Tools (for your PC)

Mapping (GPS Required)

Spectrum Analyzer Mode

Mobile WiMAX OTA, LTE OTA Options

Folder Spectrogram (Spectrum Monitoring for Interference Analysis and Spectrum Clearing)

Folder Spectrogram – 2D View

Video Folder Spectrogram – 2D View

Folder Spectrogram – 3D View

List/Parameter Editors

Tra ce s

Product Updates

Pass/Fail

Languages

Connectivity

Connections

MapInfo, MapPoint Google Earth, Google Maps, MapInfo

Creates a composite file of multiple traces Peak Power, Total Power, Peak Frequency, Histogram, Average Power (Max/Min) File Filter (Violations over limit lines or deviations from averages) Playback

Create AVI file to export for management review/reports Views (Set Threshold, Markers)

- 3D (Rotate X, Y, Z Axis, Level Scale, Signal ID)

- Playback (Frequency and/or Time Domain)

Add, delete, and modify limit lines and markers Auto-checks Anritsu website for latest revision firmware Create, download, or edit Signal Analysis Pass/Fail Limits Add custom language or modify non-English language menus

Connect to PC using USB

23 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Ordering Information

Ordering Information – Options

*Mutually exclusive

MT8212E MT8213E Description

2 MHz to 4 GHz 2 MHz to 6 GHz Cable and Antenna Analyzer

9 kHz to 4 GHz 9 kHz to 6 GHz Spectrum Analyzer

10 MHz to 4 GHz 10 MHz to 6 GHz Power Meter

PIM Analyzer (requires PIM Master)

Options Options

MT8212E-0021 MT8213E-0021 2-Port Transmission Measurement

MT8212E-0010 MT8213E-0010 Bias-Tee

MT8212E-0031 MT8213E-0031 GPS Receiver (requires Antenna)

MT8212E-0019 MT8213E-0019 High-Accuracy Power Meter (requires External Power Sensor)

MT8212E-0025 MT8213E-0025 Interference Analyzer (Option 0031 recommended)

MT8212E-0027 MT8213E-0027 Channel Scanner

MT8212E-0431 MT8213E-0431 Coverage Mapping (requires Option 0031)

MT8212E-0090 MT8213E-0090 Gated Sweep

MT8212E-0028 MT8213E-0028 C/W Signal Generator (requires CW Signal Generator Kit, P/N 69793)

MT8212E-0040 MT8213E-0040 GSM/EDGE RF Measurements MT8212E-0041 MT8213E-0041 GSM/EDGE Demodulation

MT8212E-0044 MT8213E-0044 W-CDMA/HSPA+ RF Measurements MT8212E-0065 MT8213E-0065 W-CDMA/HSPA+ Demodulation MT8212E-0035 MT8213E-0035 W-CDMA/HSPA+ OTA Measurements

MT8212E-0060 MT8213E-0060 TD-SCDMA/HSPA+ Measurements MT8212E-0061 MT8213E-0061 TD-SCDMA/HSPA+ Demodulation MT8212E-0038 MT8213E-0038 TD-SCDMA/HSPA+ OTA Measurements (recommend Option 0031)

MT8212E-0541 MT8213E-0541 LTE RF Measurements MT8212E-0542 MT8213E-0542 LTE Modulation Measurements MT8212E-0546 MT8213E-0546 LTE OTA Measurements (recommend Option 0031)

MT8212E-0551 MT8213E-0551 TD-LTE RF Measurements MT8212E-0552 MT8213E-0552 TD-LTE Modulation Measurements MT8212E-0556 MT8213E-0556 TD-LTE OTA Measurements (recommend Option 0031)

MT8212E-0042 MT8213E-0042 CDMA RF Measurements MT8212E-0043 MT8213E-0043 CDMA Demodulation MT8212E-0033 MT8213E-0033 CDMA OTA Measurements (requires Option 0031)

MT8212E-0062 MT8213E-0062 EV-DO RF Measurements MT8212E-0063 MT8213E-0063 EV-DO Demodulation MT8212E-0034 MT8213E-0034 EV-DO OTA Measurements (requires Option 0031)

MT8212E-0046 MT8213E-0046 Fixed WiMAX RF Measurements MT8212E-0047 MT8213E-0047 Fixed WiMAX Demodulation

MT8212E-0066 MT8213E-0066 Mobile WiMAX RF Measurements MT8212E-0067 MT8213E-0067 Mobile WiMAX Demodulation MT8212E-0037 MT8213E-0037 Mobile WiMAX OTA Measurements (recommend Option 0031)

MT8212E-0030 MT8213E-0030 ISDB-T Digital Video Measurements MT8212E-0032 MT8213E-0032 ISDB-T SFN Measurements MT8212E-0079 MT8213E-0079 ISDB-T BER Measurements (Requires option 0030, cannot be ordered with option 0051,

MT8212E-0064 MT8213E-0064 DVB-T/H Digital Video Measurements MT8212E-0078 MT8213E-0078 DVB-T/H SFN Measurements MT8212E-0057 MT8213E-0057 DVB-T/H BER Measurements (Requires option 0064, cannot be ordered with option

MT8212E-0051 MT8213E-0051 T1 Analyzer* MT8212E-0052 MT8213E-0052 E1 Analyzer* MT8212E-0053 MT8213E-0053 T3/T1 Analyzer*

MT8212E-0098 MT8213E-0098 Standard Calibration (ANSI 2540-1-1994) MT8212E-0099 MT8213E-0099 Premium Calibration to (ANSI 2540-1-1994 plus test data)

0052 or 0053)

0051, 0052 or 0053)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 24 of 32

Ordering Information Cell Master™ MT8212E and MT8213E

Standard Accessories (Included with instrument)

Part Number Description

10920-00060 Handheld Instruments Documentation Disc

10580-00250 Cell Master User Guide (includes Bias-Tee, GPS Receiver)

2000-1654-R Soft Carrying Case

2300-498 Master Software Tools (MST) CD Disc

2300-530 Anritsu Tool Box with Line Sweep Tools (LST) DVD Disc

2300-539 easyTest Tools CD Disc

633-75 Rechargeable Li-Ion Battery, 7500 mAh

40-187-R AC-DC Adapter

806-141-R Automotive Cigarette Lighter 12V VDC Adapter

3-2000-1498 USB A/5-pin mini-B Cable, 10 feet/305 cm

11410-00485 Cell Master MT8212E/MT8213E Technical Data Sheet

One Year Warranty (Including battery, firmware, and software) Certificate of Calibration and Conformance

Power Sensors (For complete ordering information see the respective datasheets of each sensor)

Model Number Description

PSN50 High Accuracy RF Power Sensor, 50 MHz to 6 GHz, +20 dBm

MA24106A High Accuracy RF Power Sensor, 50 MHz to 6 GHz, +23 dBm

MA24104A Inline High Power Sensor, 600 MHz to 4 GHz, +51.76 dBm

MA24105A Inline High/Peak Power Sensor, 350 MHz to 4 GHz, +3 dBm to

MA24108A Microwave USB Power Sensor, 10 MHz to 8 GHz, +20 dBm

MA24118A Microwave USB Power Sensor, 10 MHz to 18 GHz, +20 dBm

MA24126A Microwave USB Power Sensor, 10 MHz to 26 GHz, +20 dBm

+51.76 dBm

Manuals (Soft copy included on Handheld Instruments Documentation Disc and at www.anritsu.com)

Part Number Description

10920-00060 Handheld Instruments Documentation Disc

10580-00250 Cell Master User Guide (Hard copy included)

- Bias-Tee, GPS Receiver

10580-00241 Cable and Antenna Analyzer Measurement Guide

10580-00242 2-Port Transmission Measurement

- Bias-Tee

10580-00244 Spectrum Analyzer Measurement Guide

- Interference Analyzer, Channel Scanner, Gated Sweep, CW Signal Generator, AM/FM/PM Analyzer, Interference Mapping, Coverage Mapping

10580-00240 Power Meter Measurement Guide

- High Accuracy Power Meter

10580-00234 3GPP Signal Analyzer Measurement Guide

- GSM/EDGE, W-CDMA/HSDPA, TD-SCDMA/HSDPA, LTE

10580-00235 3GPP2 Signal Analyzer Measurement Guide

- CDMA, EV-DO

10580-00236 WiMAX Signal Analyzer Measurement Guide

- Fixed WiMAX, Mobile WiMAX

10580-00237 Digital TV Measurement Guide

- DVB-T/H, ISDB-T

10580-00238 Backhaul Analyzer Measurement Guide

- T1, E1, T3/T1

10580-00256 Programming Manual

10580-00280 PIM Master User Guide

25 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Ordering Information

Trouble Shooting Guides (Soft copy at www.anritsu.com)

Part Number Description

11410-00473 Cable, Antenna and Components

11410-00551 Spectrum Analyzers

11410-00472 Interference

11410-00566 LTE eNodeB Testing

11410-00615 TD-LTE eNodeB Testing

11410-00466 GSM/GPRS/EDGE Base Stations

11410-00463 W-CDMA/HSDPA Base Stations

11410-00465 TD-SCDMA/HSDPA Base Stations

11410-00467 cdmaOne/CDMA2000 1X Base Stations

11410-00468 CDMA2000 1xEV-DO Base Stations

11410-00470 Fixed WiMAX Base Stations

11410-00469 Mobile WiMAX Base Stations

11410-00552 T1/DS1 Backhaul Testing

11410-00553 E1 Backhaul Testing

Optional Accessories

Calibration Components, 50 Ω

Part Number Description

ICN50B InstaCal™ Calibration Module, 38 dB, 2 MHz to 6.0 GHz, N(m), 50 Ω

OSLN50-1 Precision Open/Short/Load, N(m), 42 dB, 6.0 GHz, 50 Ω

OSLNF50-1 Precision Open/Short/Load, N(f), 42 dB, 6.0 GHz, 50 Ω

2000-1618-R Precision Open/Short/Load, 7/16 DIN(m), DC to 6.0 GHz 50 Ω

2000-1619-R Precision Open/Short/Load, 7/16 DIN(f), DC to 6.0 GHz 50 Ω

22N50 Open/Short, N(m), DC to 18 GHz, 50 Ω

22NF50 Open/Short, N(f), DC to 18 GHz, 50 Ω

SM/PL-1 Precision Load, N(m), 42 dB, 6.0 GHz

SM/PLNF-1 Precision Load, N(f), 42 dB, 6.0 GHz

Calibration Components, 75 Ω

Part Number Description

22N75 Open/Short, N(m), DC to 3 GHz, 75 Ω

22NF75 Open/Short, N(f), DC to 3 GHz, 75 Ω

26N75A Precision Termination, N(m), DC to 3 GHz, 75 Ω

26NF75A Precision Termination, N(f), DC to 3 GHz, 75 Ω

12N50-75B Matching Pad, DC to 3 GHz, 50 Ω to 75 Ω

Phase-Stable Test Port Cables, Armored w/Reinforced Grip (Recommended for cable & antenna line sweep applications)

Part Number Description

15RNFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15RDFN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω

15RDN50-1.5-R 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω

15RNFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15RDFN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω

15RDN50-3.0-R 3.0 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 26 of 32

Ordering Information Cell Master™ MT8212E and MT8213E

Optional Accessories (Continued)

Interchangeable Adaptor Phase Stable Test Port Cables, Armored w/Reinforced Grip (recommended for cable and

antenna line sweep applications. It uses the same ruggedized grip as the Reinforced grip series cables. Now you can also change the adaptor interface on the grip to four different connector types)

Part Number Description

15RCN50-1.5-R 1.5 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω

15RCN50-3.0-R 3.0 m, DC to 6 GHz, N(m), N(f), 7/16 DIN(m), 7/16 DIN(f), 50 Ω

Phase-Stable Test Port Cables, Armored (Recommended for use with tightly spaced connectors and other general purpose applications)

Part Number Description

15NNF50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15NN50-1.5C 1.5 m, DC to 6 GHz, N(m) to N(m), 50 Ω

15NDF50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(f), 50 Ω

15ND50-1.5C 1.5 m, DC to 6 GHz, N(m) to 7/16 DIN(m), 50 Ω

15NNF50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15NN50-3.0C 3.0 m, DC to 6 GHz, N(m) to N(m), 50 Ω

15NNF50-5.0C 5.0 m, DC to 6 GHz, N(m) to N(f), 50 Ω

15NN50-5.0C 5.0 m, DC to 6 GHz, N(m) to N(m), 50 Ω

Adapters

Precision Adapters

Part Number Description

1091-26-R SMA(m) to N(m), DC to 18 GHz, 50 Ω

1091-27-R SMA(f) to N(m), DC to 18 GHz, 50 Ω

1091-80-R SMA(m) to N(f), DC to 18 GHz, 50 Ω

1091-81-R SMA(f) to N(f), DC to 18 GHz, 50 Ω

1091-172-R BNC(f) to N(m), DC to 1.3 GHz, 50 Ω

510-90-R 7/16 DIN(f) to N(m), DC to 7.5 GHz, 50 Ω

510-91-R 7/16 DIN(f) to N(f), DC to 7.5 GHz, 50 Ω

510-92-R 7/16 DIN(m) to N(m), DC to 7.5 GHz, 50 Ω

510-93-R 7/16 DIN(m) to N(f), DC to 7.5 GHz, 50 Ω

510-96-R 7/16 DIN(m) to 7/16 DIN (m), DC to 7.5 GHz, 50 Ω

510-97-R 7/16 DIN(f) to 7/16 DIN (f), DC to 7.5 GHz, 50 Ω

1091-379-R Reinforced-Grip TMA Bypass Adapter, 7/16 DIN(f) - 7/16 DIN(f),

510-102-R N(m) to N(m), DC to 11 GHz, 50 Ω, 90 degrees right angle

Part Number Description

34NN50A Precision Adapter, N(m) to N(m), DC to 18 GHz, 50 Ω

34NFNF50 Precision Adapter, N(f) to N(f), DC to 18 GHz, 50 Ω

DC to 6 GHz, 50 Ω

27 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Ordering Information

Optional Accessories (Continued)

Miscellaneous Accessories

Part Number Description

69793 CW Signal Generator Kit

2000-1528-R GPS Antenna, SMA(m) with 15 foot cable

2000-1652-R GPS Antenna, SMA(m) with 1 foot cable

2000-1689 EMI Near Field Probe Kit

2000-1374 External Charger for Li-lon Batteries

2300-532 Map Master CD

633-75 7500 mAh High-Capacity Battery Pack

2000-1653 Anti-glare Screen Cover (package of 2)

Backpack and Transit Case

Part Number Description

67135 Anritsu Backpack (For Handheld Instrument and PC)

760-243-R Large Transit Case with Wheels and Handle

Directional Antennas

Portable Antennas

Part Number Description

2000-1411-R 822 MHz to 900 MHz, N(f), 10 dBd, Yagi

2000-1412-R 885 MHz to 975 MHz, N(f), 10 dBd, Yagi

2000-1413-R 1710 MHz to 1880 MHz, N(f), 10 dBd. Yagi

2000-1414-R 1850 MHz to 1990 MHz, N(f), 9.3 dBd, Yagi

2000-1415-R 2400 MHz to 2500 MHz, N(f), 10 dBd, Yagi

2000-1416-R 1920 MHz to 2170 MHz, N(f), 10 dBd, Yagi

2000-1617 600 MHz to 21 GHz, N(f), 5-8 dBi to 12 GHz, 0-6 dBi to 21 GHz,

2000-1659-R 698 MHz to 787 MHz, N(f), 8 dBd, Yagi

2000-1660-R 1425 MHz to 1535 MHz, N(f), 12 dBd, Yagi

2000-1677-R 300 MHz to 3 GHz, SMA(m), log periodic

Part Number Description

2000-1200-R 806 MHz to 866 MHz, SMA(m), 50 Ω

2000-1473-R 870 MHz to 960 MHz, SMA(m), 50 Ω

2000-1035-R 896 MHz to 941 MHz, SMA(m), 50 Ω (1/2 wave)

2000-1030-R 1710 MHz to 1880 MHz, SMA(m), 50 Ω (1/2 wave)

2000-1474-R 1710 MHz to 1880 MHz with knuckle elbow (1/2 wave)

2000-1031-R 1850 MHz to 1990 MHz, SMA(m), 50 Ω (1/2 wave)

2000-1475-R 1920 MHz to 1980 MHz and 2110 MHz to 2170 MHz, SMA(m), 50 Ω

2000-1032-R 2400 MHz to 2500 MHz, SMA(m), 50 Ω (1/2 wave)

2000-1361-R 2400 MHz to 2500 MHz, 5000 MHz to 6000 MHz, SMA(m), 50 Ω

2000-1636-R Antenna Kit (Consists of: 2000-1030-R, 2000-1031-R,

log periodic

2000-1032-R, 2000-1200-R, 2000-1035-R, 2000-1361-R, and carrying pouch)

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 28 of 32

Ordering Information Cell Master™ MT8212E and MT8213E

Optional Accessories (Continued)

Mag Mount Broadband Antenna

Part Number Description

2000-1647-R Cable 1: 698 MHz to 1200 MHz 2 dBi peak gain,

Cable 2: 3000 MHz to 6000 MHz 5 dBi peak gain, N(m), 50 Ω, 10 feet Cable 3: GPS 26 dB gain, SMA(m), 50 Ω, 10 feet

2000-1645-R 694 MHz to 894 MHz 3 dBi peak gain,

1700 MHz to 2700 MHz 3 dBi peak gain, N(m), 50 Ω, 10 feet

2000-1646-R 750 MHz to 1250 MHz 3 dBi peak gain,

1650 MHz to 2000 MHz 5 dBi peak gain, 2100 MHz to 2700 MHz 3 dBi peak gain, N(m), 50 Ω, 10 feet

2000-1648-R 1700 MHz to 6000 MHz 3 dBi peak gain, N(m), 50 Ω, 10 feet

Filters

Part Number Description

1030-114-R 806 MHz to 869 MHz, N(m) to SMA(f), 50 Ω

1030-109-R 824 MHz to 849 MHz, N(m) to SMA(f), 50 Ω

1030-110-R 880 MHz to 915 MHz, N(m) to SMA(f), 50 Ω

1030-111-R 1850 MHz to 1910 MHz, N(m) to SMA(f), 50 Ω

1030-112-R 2400 MHz to 2484 MHz, N(m) to SMA(f), 50 Ω

1030-105-R 890 MHz to 915 MHz, N(m) to N(f),50 Ω

1030-106-R 1710 MHz to 1790 MHz, N(m) to N(f), 50 Ω

1030-107-R 1910 MHz to 1990 MHz, N(m) to N(f), 50 Ω

1030-149-R High Pass, 150 MHz, N(m) to N(f), 50 Ω

1030-150-R High Pass, 400 MHz, N(m) to N(f), 50 Ω

1030-151-R High Pass, 700 MHz, N(m) to N(f), 50 Ω

1030-152-R Low Pass, 200 MHz, N(m) to N(f), 50 Ω

1030-153-R Low Pass, 550 MHz, N(m) to N(f), 50 Ω

1030-155-R 2500 MHz to 2700 MHz, N(m) to N(f), 50 Ω

1030-178-R 1920 MHz to 1980 MHz, N(m) to N(f), 50 Ω

1030-179-R 777 MHz to 797 MHz, N(m) to N(f), 50 Ω

1030-180-R 2500 MHz to 2570 MHz, N(m) to N(f), 50 Ω

2000-1684-R 791 MHz to 821 MHz, N(m) to N(f), 50 Ω

1700 MHz to 2700 MHz 5 dBi peak gain, N(m), 50 Ω, 10 feet

Attenuators

Part Number Description

3-1010-122 20 dB, 5 W, DC to 12.4 GHz, N(m) to N(f)

42N50-20 20 dB, 5 W, DC to 18 GHz, N(m) to N(f)

42N50A-30 30 dB, 50 W, DC to 18 GHz, N(m) to N(f)

3-1010-123 30 dB, 50 W, DC to 8.5 GHz, N(m) to N(f)

1010-127-R 30 dB, 150 W, DC to 3 GHz, N(m) to N(f)

3-1010-124 40 dB, 100 W, DC to 8.5 GHz, N(m) to N(f), Uni-directional

1010-121 40 dB, 100 W, DC to 18 GHz, N(m) to N(f), Uni-directional

1010-128-R 40 dB, 150 W, DC to 3 GHz, N(m) to N(f)

T1/E1 Extender Cables

Part Number Description

806-16-R Bantam Plug to Bantam Plug

3-806-116 Bantam Plug to BNC

3-806-117 Bantam "Y" Plug to RJ48

3-806-169 72 inch (1.8 m) BNC to BNC, 75 1/2 RG59 Type Coax Cable

806-176-R Bantam Plug to Alligator Clips

29 of 32 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Notes

2-30 PN: 11410-00485 Rev. M MT8212E and MT8213E TDS

Cell Master™ MT8212E and MT8213E Ordering Information

Notes

MT8212E and MT8213E TDS PN: 11410-00485 Rev. M 31 of 32

The Master Users Group is an organization dedicated to providing training, technical support, networking opportunities and links to Master product development teams. As a member you will receive the Insite Quarterly Newsletter with user stories, measurement tips, new product news and more.

Visit us to register today: www.anritsu.com/mug

To receive a quote to purchase a product or order accessories visit our online ordering site:

www.ShopAnritsu.com

Training at Anritsu

Anritsu has designed courses to help you stay up to date with technologies important to your job. For available training courses visit: www.anritsu.com/training

• United States Anritsu Company

1155 East Collins Blvd., Suite 100, Richardson, TX 75081, U.S.A. Toll Free: 1-800-267-4878 Phone: +1-972-644-1777 Fax: +1-972-671-1877

• Canada Anritsu Electronics Ltd.

700 Silver Seven Road, Suite 120, Kanata, Ontario K2V 1C3, Canada Phone: +1-613-591-2003 Fax: +1-613-591-1006

• Brazil Anritsu Electrônica Ltda.

Praça Amadeu Amaral, 27 - 1 Andar 01327-010 Paraiso, São Paulo, Brazil Phone: +55-11-3283-2511 Fax: +55-11-3288-6940

• Mexico Anritsu Company, S.A. de C.V.

Av. Ejército Nacional No. 579 Piso 9, Col. Granada 11520 México, D.F., México Phone: +52-55-1101-2370 Fax: +52-55-5254-3147

• United Kingdom Anritsu EMEA Ltd.

200 Capability Green, Luton, Bedfordshire LU1 3LU, U.K. Phone: +44-1582-433280 Fax: +44-1582-731303

• France Anritsu S.A.

12 Avenue du Québec, Bâtiment Iris 1-Silic 612, 91140 VILLEBON SUR YVETTE, France Phone: +33-1-60-92-15-50 Fax: +33-1-64-46-10-65

• Germany Anritsu GmbH

Nemetschek Haus, Konrad-Zuse-Platz 1 81829 München, Germany Phone: +49-89-442308-0 Fax: +49-89-442308-55

List Revision Date: 20121226

® Anritsu All trademarks are registered trademarks of their respective companies. Data subject to change without noti ce. For the most recent specifications visit: www.anritsu.com Anritsu prints on recycled paper with vegetable soybean oil ink.

32 of 32

• Italy Anritsu S.r.l.

Via Elio Vittorini 129, 00144 Roma, Italy Phone: +39-06-509-9711 Fax: +39-06-502-2425

• Sweden Anritsu AB

Borgafjordsgatan 13A, 164 40 KISTA, Sweden Phone: +46-8-534-707-00 Fax: +46-8-534-707-30

• Finland Anritsu Finland

Teknobulevardi 3-5, 01530 Vantaa, Finland Phone: +358-20-741-8100 Fax: +358-20-741-8111

• Denmark Anritsu A/S (for Service Assurance) Anritsu AB (for Test & Measurement)

Kay Fiskers Plads 9, DK-2300 Copenhagen S, Denmark Phone: +45-3691-5035 Fax: +45-7211-2210

• Russia Anritsu EMEA Ltd. Representation Office in Russia

Tverskaya str. 16/2, bld. 1, 7th floor. Russia, 125009, Moscow Phone: +7-495-363-1694 Fax: +7-495-935-8962

• United Arab Emirates Anritsu EMEA Ltd. Dubai Liaison Office

P O Box 500413 - Dubai Internet City Al Thuraya Building, Tower 1, Suite 701, 7th Floor Dubai, United Arab Emirates Phone: +971-4-3670352 Fax: +971-4-3688460

• Singapore Anritsu Pte. Ltd.

60 Alexandra Terrace, #02-08, The Comtech (Lobby A) Singapore 118502 Phone: +65-6282-2400 Fax: +65-6282-2533

• India Anritsu India Pvt. Ltd.

2nd & 3rd Floor, #837/1, Binnamangla 1st Stage, Indiranagar, 100ft Road, Bangalore - 560038, India Phone: +91-80-4058-1300 Fax: +91-80-4058-1301

• P.R. China (Shanghai) Anritsu (China) Co., Ltd.

Room 1715, Tower A CITY CENTER of Shanghai, No.100 Zunyi Road, Chang Ning District, Shanghai 200051, P.R. China Phone: +86-21-6237-0898 Fax: +86-21-6237-0899

• Hong Kong Anritsu Company Ltd.

Unit 1006-7, 10/F., Greenfield Tower, Concordia Plaza, No. 1 Science Museum Road, Tsim Sha Tsui East, Kowloon, H ong Kong Phone: +852-2301-4980 Fax: +852-2301-3545

• Japan Anritsu Corporation

8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016 Japan Phone: +81-46-296-1221 Fax: +81-46-296-1238

• Korea Anritsu Corporation, Ltd.

502, 5FL H-Square N B/D, 681 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Korea Phone: +82-31-696-7750 Fax: +82-31-696-7751

• Australia Anritsu Pty Ltd.

Unit 21/270 Ferntree Gully Road, Notting Hill Victoria, 3168, Australia Phone: +61-3-9558-8177 Fax: +61-3-9558-8255

• Taiwan Anritsu Company Inc.

7F, No. 316, Sec. 1, Neihu Rd., Taipei 114, Taiwan Phone: +886-2-8751-1816 Fax: +886-2-8751-1817

MT8212E and MT8213E Cell Master™TDS

Atec MT8212E, MT8213E User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual