Atec CBA400M-110 User Manual

CBa 4 00M-110
10 kHz to 400 MHz 110 Wat t Class a BroadBand aMplifier
Designed specically for automotive, military and aerospace BCI and other susceptibility EMC testing, this mismatch tolerant Class A amplier delivers power continuously into the varying match typically associated with this type of testing.
The GaAs Class A push pull design ensures a high reliability, low distortion linear performance across the frequency range. This design also ensures that the amplier will continue to operate at full power even when presented with an open or short circuit at its output. The use of gallium arsenide technolog y rep -
Class A linear and low distortion
design
High reliability gallium arsenide
Mismatch tolerant and uncondi-
tionally stable Wide instantaneous bandwidth Remote control option Three year parts and labour
warranty
resents a breakthrough in amplier design for this frequency range and output power. Previous designs based on silicon technolog y suffer from relatively poor compression characteristics, low efciency and sometimes poor reliability.
The unit is powered from a switched mode power supply for high efciency, high power factor and wide voltage range operation. The unit is air-cooled with integral fans, and is protected against faulty cooling by excess temperature sensing. A safety interlock connector is provided, which the user can short circuit to ground, to put the amplier into standby mode. Front panel indicators are provided to indicate over-temperature and rf interlock operation.
CBa 4 00M-110
10 kHz to 400 MHz 110 Wat t Class a BroadBand aMplifier
Technical specifications
Frequency range 10 kHz to 400 MHz Rated output power 100 W minimum Output power at 1 dB gain compression 80 W minimum
110 W typical below 100 MHz Gain (nominal) 51 dB Third order intercept point Gain variation with frequency ±2 dB Harmonics at 80 W output power Better than -20 dBc Output Impedance 50 Ohms Stability Unconditional Output VSWR tolerance Input VSWR 2:1
RF connector style Input Type N female Output Type N female
Safety interlock Dual input, O/C and/or S/C to mute USB interface Optional Supply voltage 100 to 240 Vac (+/- 10%) Supply frequency range 45 to 63 Hz Supply power <1 kVA (typical 700 VA) Mains connector Appropriate IEC 60309 plug (see options) Conducted and radiated emissions EN61326 Class A Conducted and radiated immunity EN61326: 1997 table 1 Mains harmonic currents EN61000-3-2 Voltage uctuations and icker EN61000-3-3 Safety EN61010-1 Case dimensions 19 inch, 4U case, 440 mm deep Mass 18 kg Operating temperature range 0 to 40°C
1
61 dBm
2
Innity:1
Teseq AG
Nordstrasse 11F 4542 Luterbach Switzer land T + 41 32 681 40 4 0 F + 41 32 681 4 0 48 sales@teseq.com w ww.teseq.com
© July 2011 Teseq® Specifications subject to change without notice.
®
Tes eq
is an ISO-registered company. Its products are designed and manufactured under the strict quality and environmental requirements of the ISO
9001. This documen t has been carefully checked. However, Teseq errors or inaccuracies.
691-278A August 2011
®
does not assume any liability for
Options (select at time of ordering ) 341-745 Bench model with front panel mounted input/output connectors 341-845 Rack mountable with front panel mounted input/output connectors 341-945 Rack mountable with rear panel mounted input/output connectors
Notes:
1. The third order intercept point is a nominal value, as its calculation depends upon the power level at which distortion measurements are made.
2. Output VSWR tolerance is specied for excitation within the permitted levels and frequency range.
Loading...