Atec CA-8332, CA-8334 User Manual

Site ALSTOM POWER Service - Massy (France)
Display your network analysis… all in picture format!
Ready-to-use measurements in a glance
Structured use for accurate and effective operations
Very simple connections; easily accessed keys
An instrument "built for the field"
Measurements made in compliance with EN 50160
OBSERVE, DIAGNOSE, MONITOR...
C.A 8332 C.A 8334
ThreePhase
Power Quality
Analysers
Principal parameters measured:
TRMS AC+DC voltage: single voltage
up to 480 V; phase-phase voltage up to 600 V.
TRMS AC, AC+DC current up to 3000 A
(according to sensors used).
Peak voltage and current.
Frequency from 40 to 70 Hz.
Active, reactive and apparent power per phase
and their aggregate.
Active, reactive, consumed and produced energy.
Harmonics for voltage, current, or power up
to the 50thorder.
Principal values computed:
Neutral current.
Crest factors for current and voltage.
K factors for current (transformer application).
Power factor, displacement factor and tangent.
Short-term voltage flicker.
Voltage and current unbalance.
Total harmonic distortion.
Average, min and max values
of any computed value.
Regardless of the screen, the synergy between the display and the keyboard is very efficient.
Additional functions:
Graphic data processing.
Alarms, transients.
Recording, dating and characteristics of
disturbances (swells, dips and interruptions, etc.)
Data storage.
Immediate screen printout to printer.
Screen storage.
Optical link communication.
Designed for Electrical Energy departments and Maintenance services in industrial and administrative buildings, the Qualistar C.A 8332 and C.A 8334 give an instantaneous image of the main characteristics of the quality of your electrical network. These instruments also provide numerous calculated values and processing functions in compliance with standards in use (EN 50160, IEC 61000-4-15, IEC 61000-4-30, IEC 61000-4-7).
Display mode
Horizontal cursor
Vertical cursor
for selecting phases
Date and Hour
Battery status
Pop-up menu functions; the active function stays yellow.
PRESENTATION
A keyboard divided into easily identifiable zones
Along with its high-performance measurements, the Qualistar is ergonomic and offers a user-friendly operating mode.
Waveform Mode
FUNCTIONS
Global THD and phase by phase in U, I, V, VA in %, RMS value and harmonics phase shift. Only the C.A 8334 model offers the harmonics function in VA and the “expert mode”. This mode provides an analysis of harmonics influence on neutral heating or rotating machines.
Power / Energy Mode
"Diagnosis" stage:
Harmonics Mode
Very structured display modes for 3 distinct stages
"Observation" stage:
In this mode, three types of representations are possible: graphic, table, vectoral. RMS measurements in U and I. PEAK, MIN, MAX, AVG, KF, Pst, CF, phase shift, unbalance measurements…
This mode displays all of the values relative to the power and energy. The Start and Stop keys activate and deactivate the aggregate of energies. Measurements for:
W, V ar, VA Wh, Warh, VAh PF, DPF or cos ϕ and tan ϕ
Pop-up menus
Display modes
Cursors and validation
Direct functions
The keys, which are clearly identifiable by their shapes, positioning and pictogram, make mastering the instrument's functions rapid and easy.
Configuring instrument via software: setup, recording and alarms modes. Recorded and alarm data processing. Graphic representation of data in Windows
TM
environment. Data analysis in compliance with EN 50160 standard. Screen printout and transient transfers in BMP format. 3D representation of harmonics. Data to spreadsheet transfer (Excel).
Input characteristics
Voltages: phase-phase: 600 V TRMS
phase-neutral: 480 V TRMS
Currents: according to sensors
MN clamp: 2 A... 240 A C clamp: 3 A... 1 200 A AmpFLEX: 10 A... 3 000 A PAC: 10 A... 1 000 A AC
10 A... 1 400 A DC
Adapter unit casing for external CT
SPECIFICATIONS
General characteristics
Power supply: Mains: 110 V and 230 V
NiMH (9.6 V) rechargeable battery
Autonomy: 10 hours
Temperature for use: 0°... 50°C
Storage temperature: - 40°... 70°C
Standards: EN IEC 61010, 600 V cat. III, pollution 2
Double insulation for inputs and outputs
Dimensions (L x W x H): 180 x 55 x 240
Weight: 1.5 kg with battery
Frequency range: 40 - 70 Hz
Voltage accuracy: ± 0.5 %
Current: ± 0.5 %
Power: ±1 %
Power factor: ±0.01
Frequency: ±0.01 Hz
THD (total harmonic distortion): ±1 % L ±2 pts
Energy: ±1 % L
Sampling frequency: 12.8 kHz / channel at 50 Hz
Functional characteristics
Functions C.A 8332 C.A 8334 Display color LCD 320 x 240 color LCD 320 x 240 Memory 2 Mbytes 4 Mbytes Battery 1800 mAh 3800 mAh Harmonics Yes Yes + expert mode Recording Yes (limited) Yes Alarms Yes Yes Transients No Yes Mains AC+DC AC+DC Digital link RS 232 RS 232
With the around-the-neck holder, making measurements is easy: operating the instrument and reading the displays at the same time.
All desired parameters are saved with their visual graphics during a recording. Note that a bargraph located at the top of the window gives the total recording period, programmable recording period and storing rate.
The transient mode captures changes of the voltage and current with triggers on thresholds. Representation over 4 periods of the captured event at 256 counts / period, also available with zoom.
Transient Mode
"Monitoring" stage:
Alarms Mode
The simplicity of the instrument's set-up is enhanced by the use of graphic representations: type of clamp, connection, color of phases, parameters to record…
Qualistar can be connected directly to a printer for immediate screen printing.
If needed, the help key explains functions in relation to the viewed screen in simple terms.
Press this key to make a copy of the screen. Storing the viewed screen is automatic with date and time recording. Up to 12 screen recordings (C.A 8334).
Recording Mode
Printing
Help
The alarms are defined during the instrument's configuration. The alarm mode displays all threshold events which occur during the measurement period.
Direct function keys:
Configuration
Screen Shot
Automatic time and date recording of the alarm, the maximum corresponding value, and the duration of the event.
YOUR DISTRIBUTOR
TEST & MEASUREMENT DIVISION
FRANCE
190, rue Championnet 75876 PARIS Cedex 18 Tel: +33 1 44 85 44 86 Fax: +33 1 46 27 95 59 e-mail: export@chauvin-arnoux.fr www.chauvin-arnoux.fr
UNITED KINGDOM
Waldeck House - Waldeck Road MAIDENHEAD SL6 8BR Tel: 01628 788 888 Fax: 01628 628 099 e-mail: info@chauvin-arnoux.co.uk www.chauvin-arnoux.co.uk
Power Quality Analyser :
Instrument comes complete (as per grid) with:
- 1 QualistarView software
- 1 DB9F standard optical lead
- 4 x 3m leads fitted with banana plugs
- 4 crocodile clips
- 1 mains lead
- User's manual
VERSIONS (terminals colors)
French (red, green, yellow, blue) F R International (red, blue, black, white) I N
CURRENT SENSORS IN A SHOULDER BAG
None XX Set of 3 C193 clamps (1000A- dia: 52 mm) C X Set of 3 Ampflex A193 (3000A-dia: 140 mm / length 450 mm) A 1 Set of 3 Ampflex A193 (3000A-dia: 250 mm / length 800 mm) A 2 Set of 3 MN93 clamps (240A- dia: 20 mm) M N Set of 3 PAC93 clamps (1400A- dia: 42 mm) P A
USER'S MANUAL LANGUAGES
French (by default) FR English GB German AL Italian IT Spanish ES Portuguese PT
2P MAINS SUPPLY LEAD
French, German, or Spanish (by default) F English G Italian I Swiss C USA U
Or: P01160501: WATT C.A 8332-F MN clamp P01160503: WATT C.A 8332-Int MN clamp P01160601: WATT C.A 8334-F MN clamp P01160603: WATT C.A 8334-Int MN clamp P01160502: WATT C.A 8332-F Ampflex (450 mm) P01160504: WATT C.A 8332-Int Ampflex (450 mm) P01160602: WATT C.A 8334-F Ampflex (450 mm) P01160604: WATT C.A 8334-Int Ampflex (450 mm)
ACCESSORIES:
P01120327: SET OF 3 C193-F* CLAMPS P01120321: SET OF 3 C193-Int** CLAMPS P01120422: SET OF 3 MN 93-F* CLAMPS P01120423: SET OF 3MN 93-Int** CLAMPS P01120535: SET OF 3 AMPFLEX A193 450 mm-F* P01120523: SET OF 3 AMPFLEX A193 450 mm-Int** P01120536: SET OF 3 AMPFLEX A193 800 mm-F* P01120524: SET OF 3 AMPFLEX A193 800 mm-Int** P01120076: SET OF 3 PAC 93-F* CLAMPS P01120077: SET OF 3 PAC 93-Int** CLAMPS P01101959: 5A CA833X-F* ADAPTER UNIT P01101959A: 5A CA833X-Int** ADAPTER UNIT P01298051: SHOULDER BAG FOR CABLE N°6 P01298055: SHOULDER BAG FOR INSTRUMENT N°21
TO ORDER
906 211 032 - Ed. 2 - VS 02/2002 -
Characteristics subject to modifications according to technological developments.
C A 8 3 3 2 C A 8 3 3 4
* F = French version: User’s manual in French – L1 / red, L2 / green, L3 / yellow, N / blue ** Int. = International version: User’s manual in English – L1 / red, L2 / blue, L3 / black, N / white
Loading...