ATD Tools ATD-5203 User Manual

ATD-5203

30 GALLON PRESSURIZED OIL DRAIN TANK

ASSEMBLY & OPERATING INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Model: ATD-5203

Capacity: 30 Gallon

Drain Funnel: Adjusts from 47.25” to 70.5”

Drain Funnel Diameter: 15.75”

Plastic Tray: 11.8” x 11.8” x 2.2”

Swivel Castors: 2pc 4” X 1.2”

Wheels: 2pc 7” X 1.5”

Working Pressure: ≤7 psi (0.5bar)

IMPORTANT

READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.

READ AND UNDERSTAND ALL SAFETY WARNINGS AND PRECAUTIONS CONTAINED IN THIS MANUAL.

KEEP THIS INSTRUCTION FOR FUTURE REFERENCE.

Warning: When using product, basic safety precautions should always be followed to reduce the risk of personal

injury and damage to equipment.

Warning: The warnings cautions, and instructions discussed in this instruction manual cannot cover all possible

conditions and situations that may occur. It must be understood by the operator that common sense and caution

are factor which cannot be built into this product, but must be supplied by the operator.

INSPECTION

Check for worn parts, air leaks, and damaged, loose or missing parts before operating.

Check tank operation by connecting air to air nipple and closing ball valve.

Verify that there is sufficient air flow coming from nozzle/hose assembly.

An annual tank/component inspection is recommended.

READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

1. Keep Work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Keep area well lighted.

3. Store idle equipment. When not in use, the product must be stored in a safe and clean location. Always

up products and keep out of reach of children.

4. Use the right product for the job. There are certain applications for which the product was designed. DO

NOT modify the product and DO NOT use the product for a purpose for which it was not intended.

5. Check for damaged parts. Before using any product, any part that appears damaged should be carefully

checked to determine that it will operate properly and perform its intended function. Check for any broken or

damaged parts and any other conditions that may affe

parts immediately.

6. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any

other parts will void the warranty.

7. DO NOT operate product if under the influence of alcohol or drugs.

8. DO NOT exceed the product’s working pressure of 7 psi (0.5bar)

9. Only use on a flat surface capable of supporting the product and its maximum load.

10. Dress safely. Non-skid footwear or safety boots should be used when working with t

wear loose clothing or jewelry as they can become caught in moving parts. Wear a protective hair covering to

prevent long hair from becoming caught in moving parts.

11. DO NOT allow children in the work area.

12. Always check hardware and assembled parts after assembling. All connections should be checked and

hardware tightened.

13. DO NOT overreach. Keep proper footing and balance at all times to prevent tripping, falling and injury.

14. Always secure the wheels and casters in place while opera

15. Know and obey city and state laws for proper disposal of oil. Dispose of oil properly in accordance with

all local laws and regulations.

ct its operation. Replace or repair damaged or worn

he product. DO NOT

ting the product.

lock

SPECIFIC PRODUCT WARNING AND PRECAUTIONS

Note: This Product is to be used only for transporting oil. DO NOT use to transport any other liquid.

1. Always disconnect equipment from its air supply source and release all compressed air from the
system before performing any service or maintenance.

2. Never leave this product unattended while operating or evacuating oil.

3. Never use this equipment near open flame or heat sources.

4. Always raise Drain Bowl and clos e bal l valve (8#) before evacuating oil. Never attempt to pressurize the

tank with the ball valve open.

5. If the bleeder valve ever relieves any air pressure from the tank, remove the unit from service immediately

and contact a qualified service technician.

6. If used oil does not evacuate from tank upon pressurization, check that ball valves are fully in the correct

positions. If this does not correct the problem, removed the unit from service and contact a qualified service

technician.

ASSEMBLY

This unit requires some assembly before use. It is important that you read the entire manual to become familiar

with the product BEFORE you assemble and use the product. Before operating the tool, be sure that you have all

parts described in parts list in and assembly diagram located on the last pages of this manual.

1. Slide two wheels (#19) onto each end of the axle located at the base of the Tank (#40), secure with washer

and circlip (#17 & #18).

2. Insert the bolts on top of the casters (#22) into the flange plates. Slide flat washer (#21) and thread nut (#20)

onto bolt. Tighten securely.

3. Insert handle (#31) into the two slots on the side of the oil tank (#40). Tighten down handle screws.

4. Attach the valve assembly (#6, #7 & #8) to the oil pipe (#10).

5. Attach the funnel assembly (#1, #2, #3, #4 & #5) to valve assembly.

6. Slide drain tube (#10) up through the tube holder, slide the tension collar (#13) onto the tube and seat it down

inside of the tube holder. Slide the tension nut (#14) over the tube and thread it onto the tube holder.

Tightening this nut should increase tension on the tube, holding it in place. Slide the second tension collar

and nut (#11 & #12) onto the tube over the first tension nut assembly. When tightened, this will provide a stop,

in case the oil pan should slide downwards. Tighten snugly, but do not over tighten as these tension collars

are both used for adjusting the height of the oil drain pan. Now, attach the funnel and valve assembly (#1, #2,

#3, #4 & #5) to the top of the drain tube.

7. Snap plastic tray (#39) onto the tabs provided on top of the oil tank.

8. Check all connections to hoses and valves to ensure that there will be no leaks.

9. Check to make sure all hardware is secured tightly. Also check to make sure the wheels rolls properly before

using your oil drain tank.