ATD Tools ATD-3699 User Manual

Replacement Parts
and EN14624
Item Part Number
Sensor with Filter Filter Kit Test Vial Carrying Case Instruction Manual
RETURN FOR REPAIR POLICY
Every effort has been made to provide reliable, superior quality products. However, in the event your instrument requires repair, forward unit to Service Center freight prepaid to the address below with return address, phone number and/or email address.
SERVICE CENTER
2651 W 81st Street
Hialeah, FL 33016
WARRANTY POLICY
The ATD3699 Refrigerant Gas Leak Detector is warranted to be free of defects in materials and workmanship for a period of two years from the date of purchase including an industry first two year warranty on the sensor. This warranty applies to all repairable instruments that have not been tampered with or damaged through improper use including unauthorized opening of the unit. Please ship warranty units that require repair freight prepaid to Service Center along with proof of purchase, return address, phone number and/or email address.
PRT3700-01 PRT3700-02 PRT3700-03 PRT3699-CASE PM-MAN0010
Refrigerant Gas Leak Detector
Detects all CFC, HFC, HCFC
Refrigerants including blends
Model ATD3699
User Manual
Design Certified to meet
SAE J2791
For R134a
INTRODUCTION
Cross Sensitivity to Automotive Chemicals
Some automotive solvents and chemicals have similar hydrocarbon properties as R134a and
. Before leak checking, clean
The ATD3699 features a long life heated sensor technology that is designed to detect the more current and difficult HFC refrigerants such as R-134a, R-410a, R-407c, R-507, and R-404c in addition to all HCFC (R22) and CFC (R12) refrigerants including SNAP approved hydrocarbon blends.
The ATD3699’s unique digital leak size indicator takes the guesswork out of whether or not to repair a small leak. The digital display is independent from the audio alarm and sensitivity level, allowing the precise pinpointing of the leak source.
The ATD3699 does not require rechargeable batteries.
Unique numeric leak size
R134a sensitivity .05 oz/yr
Certified to meet new SAE
Visual LED leak alarm near
Indicator
2791 standard
FEATURES
Long life, stable sensor
R22 sensitivity .025 oz/yr
Automatic calibration and
reset to ambient
3 adjustable sensitivity levels
sensor
Low battery indicator
Audio mute function
SAE J1627 Certified
Garage Tough
2- year warranty including 2
True mechanical pump
Uses 4 AA alkaline batteries
Comfortable Sanoprene grip
CE Certified
Made in USA
years for the sensor
1
Minimum/Maximum Sensitivity Threshold (fixed) 1 gm/yr minimum, >50 gm/yr maximum Minimum/Maximum Sensitivity Threshold (moving) 3 gm/yr minimum, > 50 gm/yr maximum
Minimum Detection Time (1gm/yr) Approx 1 sec Clearing Time Approx 9 seconds after exposure to >50
Minimum Threshold after Maximum Exposure 1 gm/yr Sensitivity Threshold in Polluted Atmosphere 1 gm/yr Calibration Frequency 1/yr check with calibrated leak Standard
may elicit a positive response (<30 seconds) from the ATD3699 up any chemicals in the list below that elicit a positive response.
Dextron Transmission fluid heated to 160 ºF N N/A Quaker State Motor Oil heated to 160 ºF N N/A Rain-X Windshield Wash Fluid N N/A Ford silicone lubricant N N/A Ford Rust Inhibitor (when wet) Y Yes Ford Gasket Adhesive (when wet) Y Yes Loctite Natural Blue degreaser (undiluted) Y Yes
Ford Brake Parts Cleaner (when wet) Y Ford Silicone Rubber (when uncured) Y Yes
Motorcraft Antifreeze heated to 160 ºF Y Yes Gunk liquid wrench (when wet) Y Yes Ford Spot Remover (when wet) Y Yes Ford Pumice lotion (with mineral solvent) Y Yes Ford Motorcraft brake fluid Y Yes Ford Carburetor Cleaner (when wet) Y Yes
Model # ATD3699
Name Leak Detector, Refrigerant Gas
Sensitivity
Sensor Life > 300 hours
Response Time Instantaneous
Power Supply 4 AA Alkaline batteries
Battery Life 8 hours continuous
Warm up time < 20 seconds
Probe length 17 inches
Numerical Display 7 segment digital display (1 to 9)
Weight, lbs 1.5 lbs Warranty 2 years (includes sensor)
Brand/Chemical Name Response
Product Specifications
EN14624/2005 Test Specifications
.05 oz/yr R134a .025 oz/yr R22
gm/yr
Clears
<30 seconds
Yes
6
Maintenance
Filter
Keyway
alignment
Batteries:
Remove screw located at rear end of unit and
pull down hinged battery door to open as shown. Always insert all
ies into the battery compartment in the same direction.
Note polarity mark on the inside of the battery door for proper
: Unscrew sensor tip as shown to replace filter.
bly dirty or every 2 to 3
Install
the new sensor by aligning the notch in sensor cover with the raised
sensor into socket. Misalignment can
Press the ON/OFF button once to turn on and again
: The detector automatically starts heating the sensor.
and the detector will sound a slow “beep”. Warm up is usually
: The detector is ready to begin searching for leaks when
he
audio “beep” increases in frequency and probe LED begins to
Digital Leak Size
Low Battery
Indicator
Sensitivity Level
Audio Mute &
Sensitivity Level
Power
Install Batteries:
four batter
battery orientation.
Polarity Mark
Sensor:
Replace Filter
Replace filter whenever it becomes visi months depending on use.
Replace Sensor: Remove sensor by pulling out of socket.
keyway on sensor socket holder (see figure below).
Note: Do not force damage the sensor pins.
Push straight on (do not
Unscrew tip to
replace filter
twist) to install sensor
ATD3699 Control Panel
Indicator
On/Off
Operating Instructions
1. TURN ON: to turn off.
2. WARM UP During the heating cycle, the digital leak size indicator will flash 0
Pull straight out (do not
5
less than 20 seconds.
3. READY the flashing 0 stops and the green sensitivity LED turns on. T
blink steadily.
2
Leak Size Indicator
The digital leak size indicator remains off normally but once a leak is detected, a number from 1-9 will be displayed for all HFC and HCFC refrigerants regardless of the sensitivity
setting.
The number will continue to increase or decrease depending on the amount of refrigerant sensed. The maximum value will be displayed once the leak source has been located. The table below can be used to approximate the size of leak:
Maximum # displayed Leak Size (oz/yr)
1 -3 < 0.1
4-6 0.1 to 0.5 7-9 >0.5
Low Battery Indicator
Replace the 4 AA Alkaline batteries when the red LED on the control panel is lit. Follow battery installation instructions under Maintenance section.
Audio Mute Function
To silence or mute the audio beep and alarm signal, press the MUTE button. To restore the audio sound, press the MUTE button again. (Note: a few seconds is required to restore sound if the mute button is pressed in rapid succession.)
Adjusting Sensitivity Levels
The Leak Detector will default to the NORM sensitivity level automatically once the unit comes out of the warm up cycle and the green LED will turn on.
To change sensitivity levels, press the SENS once for HI sensitivity (red LED will turn on) and again for LO sensitivity (yellow LED will turn on).
Leak Test Vial
The leak detector comes with a Leak Test Vial that allows the user to make sure the detector is performing properly. To test:
1. Remove the plastic seal cap on top of the Leak Test Vial by pulling it off (see fig. below).
2. Turn on the detector and allow the unit to complete the warm up cycle.
3. Place the sensor close to the small hole in the top of the Leak Test Vial. The beep rate should increase and the Digital Leak Size Indicator should display a number from 4-6 indicating that the sensor and electronics are working properly.
NOTE: Always remember to replace plastic seal cap after leak test is completed. Replace Test Vial when the green color is no longer visible.
Remove
Seal Cap
To test
Leak Test Vial
3
4
Loading...