ATD-30300 & ATD-31200
OWNERS MANUAL
For Your Safety Read and Save These Instructions:
Please read these important safety instructions and warnings before operating
your ATD Blower. Use the ATD Blower in accordance with the safety instructions
and warnings described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock or injuries to persons. Do not throw
these instructions away-keep them for further reference.
Read these important safety instructions:
• CONSIDER YOUR WORK AREA ENVIRONMENT. Don’t use The ATD Blower in
damp or wet locations. Don’t operate The ATD Blower in presence of flammable liquids,
gases like gasoline or other fuels, lighter fluid, cleaners, oil-based paints, natural gas,
hydrogen, coal dust, magnesium dust, grain dust, or explosive dust like gun powder. Do
not use or store near hazardous or toxic materials.
• USE SAFETY GLASSES. Also use face or dust mask if work area is dusty. The
operation of any utility blower can result in foreign objects being blown into the eyes,
which can result in severe eye damage. Always wear safety goggles complying with
ANSI Z87.1.
• DON’T ABUSE CORD. Never pull the ATD Blower cord or yank it to disconnect from
receptacle. To unplug, grasp the plug, not the cord. Keep cord away from heat, oil, and
sharp edges. Do not pull or carry by cord, use cord as handle, close a door on cord, or
pull cord around sharp edges or corners.
• SECURE THE ATD BLOWER if used in an unstable area such as on a moving RV,
etc.
• MAINTAIN THE ATD BLOWER. Keep Blower, motor and blower wheel clean. For
safer operation, follow instructions for attaching accessories. Keep handle dry, clean and
free from oil, grease and water.
• DISCONNECT THE ATD BLOWER when not in use, before servicing, and when
attaching accessories. Turn off air mover before unplugging. Don’t operate unit
unattended.
• NEVER stick a screwdriver or any other object into the ventilation openings or air
intake areas. Do not operate with any ventilation openings blocked; keep free of dust,
lint, hair or anything that may reduce airflow. Keep hair, loose clothing, fingers and all
parts of body away form openings and moving parts. DO NOT restrict air intake.
• INSPECT FOR DAMAGE before using The ATD Blower. Determine before use if it will
operate properly. Check for alignment and/or binding of the motor and blower wheel.
Inspect cord periodically for damage. Check the switch by turning the ATD Blower on
and off while unit is plugged in.
• RETURN THE ATD BLOWER for repair or to replace damaged parts if any of them are
found to be broken or if your ATD Blower is inoperative. The ATD Blower products may
only be serviced and repaired by the official The ATD Blower Repair Center.
ATD-30300 ATD-31200
ORDERING PART# PART DESCRIPTION ORDERING PART# PART DESCRIPTION
Warning: When using electric products, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and personal injury. Follow these
important safety guidelines:
• Do not use this fan with any solid-state speed control device.
• Do not use an extension cord with this air mover.
• Do not expose to rain. Store indoors.
• Do not use with damaged cord, plug or other parts.
• Keep cord away from heated surfaces.
• Do not handle plug or the air mover with wet hands.
• Do not permit fingers to touch the terminals of plug when installing or
removing the plug from the outlet.
* After servicing, any safety device (includes grilles, impeller, etc.) shall be reinstalled
or remounted as previously installed.
Troubleshooting
Problem Solution
The ATD Blower unit won’t run. 1. Ensure that The ATD Blower unit is
securely plugged into outlet or power
source.
2. Check that outlet or power source is
receiving power.
3. Check that The ATD Blower unit is
turned on.
The ATD Blower power receptacle not
working.
1. Ensure that The ATD Blower unit is
securely plugged into outlet or power
source.
2. Check that outlet or power source is
receiving power.
3. Press the reset button above the
power receptacle.
Parts Listing
PRT30300-01 MOTOR PRT31200-01 MOTOR
PRT30300-02 CAPACITOR PRT31200-02 CAPACITOR
PRT30300-04 FAN WHEEL PRT31200-04 FAN WHEEL
PRT30300-11 SPEED CONTROL KNOB PRT31200-11 SPEED CONTROL KNOB
PRT30300-12 POWER SWITCH
PRT30300-15 CIRCUIT BREAKER PRT31200-15 CIRCUIT BREAKER
PRT31200-12 POWER SWITCH
CFM Products, LLC
ATD Tools, Inc. LIMITED ONE-YEAR WARRANTY
Every ATD Blower is thoroughly inspected and tested before leaving the factory. It is
warranted to be free of defects in workmanship and materials for the period of ONE
YEAR for the date of purchase.
THIS WARRANTY IS VOID IF:
1. Alterations have been made to the product.
2. Repairs are required because of normal wear and tear.
3. Repairs have been made or attempted by anyone other than CFM Products, LLC.
4. The product has be mistreated, misused or improperly maintained and operated.
5. Use of product not Mfg. by CFM Products, LLC with the ATD Blower voids this
warranty.
In no event shall CFM Products, LLC be liable for any damage beyond the repair or replacement as described above, including without limitation, indirect, incidental, or consequential damages.
This warranty is the only warranty made and is in lieu of all other warranties, expressed
or implied including without limitation, warranties of merchantability and fitness for a
specific purpose.
This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state. Some states do not allow the exclusion or limitation of incidental
or consequential damage, so the above limitations or exclusions may not apply to you.
Some states do not allow limitation on how long an implied warranty lasts, so the above
limitations may not apply to you.
Questions or Comments?
Call us at 1-800-992-9509 or visit our website at www.cfm-products.com.
© 2006 CFM Products, Chicago, IL BB#1010 Printed in China
Loading...