Memory Installation Guide
For ASUSTOR AS6 and AS7 Series NAS
Ver.1.0.2.0225
ASUSTOR NAS Memory Installation Guide
Table of Contents
1.
Introduction ......................................................................................................... 3
1.1. Notes and Precautions ...................................................................................... 3
1.2. Parts and Tools Needed .................................................................................... 4
2. Inst allation Guide .................................................................................................. 5
2.1. For AS 6 & AS7 Tower Series ............................................................................. 5
2.1.1. Removing the Cover ..................................................................................... 5
2.1.2. Installing Memory ........................................................................................ 6
2.1.3. Replacing the Cover ..................................................................................... 7
2.2. For AS6 Rackmount Series ................................................................................ 7
2.2.1. Removing the Cover ..................................................................................... 7
3.3.1 Installing Memory ......................................................................................... 8
3.3.2 Replacing the Cover ...................................................................................... 9
2.3. For AS7 Rackmount Series .............................................................................. 10
2.3.1. Removing the Cover ................................................................................... 10
2.3.2. Installing Memory ...................................................................................... 11
2.3.3. Replacing the Cover ................................................................................... 12
3. Appendix ........................................................................................................... 14
3.1. Troubleshooting ............................................................................................. 14
3.2. Contact ASUSTOR Technical Support ................................................................ 14
Page 2 of 14
ASUSTOR NAS Memory Installation Guide
.
11.
IInnttrroodduuccttiioonn
1.1. Notes and Precautions
All AS6 Series NAS devices support up to 3GB of memory. Before adding or removing
memory modules, please read the following precautions thoroughly.
• Your NAS and memory modules use high precision components and electronic connector
technology. To avoid invalidation of the warranty during your product warranty period, we
recommend that:
Memory for AS6 and AS7 series devices may be purchased from local dealers or the
online ASUSTOR Accessories Store (http://shop.asustor.com
You should not install a memory module by yourself, if you are not familiar with
upgrading memory on a computer.
You should not touch the connectors or open the me m ory module compartment co ver.
• Addition or removal of memory modules by yourse lf m ay result in an accident or
malfunction of your NAS caused by breakage of the slot and module or a connection
mistake. In this case, a repair fee will be charged.
).
• Be careful not to injure your hands or fingers with s h arp edges of the memory module,
inner components, or circuit boards of your NAS.
• ASUSTOR does not guarantee that third party memory modules w ill work in your NAS.
• Be sure to turn off your NAS and peripherals and disconnect all attachments and
connection cables before adding or removing memory modules.
• To prevent damage from electrostatic discharge to memory modules, follow the
instructions below:
Do not work at a location that produces static electricity easily, such as on a carpet.
Before adding or removing memory modules, touch an external metal object other
than your NAS to ground yourself and eliminate static electricity. Do not touch a ny
metal parts inside the NAS.
• Do not insert a memory module into the slot facing in the wrong direction. It may cause
damage to the module or slot, or cause the circuit board to catch fire.
• Use a screwdriver that matches the size of the screws.
• Do not remove or loosen screws that are not specified to be removed.
Page 3 of 14
ASUSTOR NAS Memory Installation Guide
1.2. Parts and Tools Needed
• Phillips head screwdriver
Page 4 of 14
ASUSTOR NAS Memory Installation Guide
.
22.
IInnssttaallllaattiioonn GGuuiiddee
2.1. For AS 6 & AS7 Tower Series
22..11..11.. RReemmoovviinngg tthhee CCoovveerr
• Shutdown the NAS by selecting [Shut down] from the ADM User Menu.
• Disconnect all cables and devices connected to the NAS including the power cord.
• Use a screwdriver to loosen the three screws found on the rear of the NAS as shown
in the illustration.
Page 5 of 14
ASUSTOR NAS Memory Installation Guide
• Grip the cover from both sides with two hands and then gently push it back to
remove it from the chassis.
22..11..22.. IInnssttaalllliinngg MMeemmoorryy
• When inserting the memory module into the empty slot, please make sure to a lign
the notches on the module with the notches in the s lo t .
• Diagonally slide in the memory module (as shown in the illust ration) making sure
that the memory module’s connectors are fully inserted into the slot.
Page 6 of 14
ASUSTOR NAS Memory Installation Guide
• Using two fingers, carefully push down and then back on the memory module until it
clicks into place. You should be able to hear an audible “click”.
22..11..33.. RReeppllaacciinngg tthhee CCoovveerr
• Replace the cover and tighten the three screws that were removed previously.
• Reconnect all cables incl uding the power cord and then start up the NAS.
2.2. Fo r AS6 Rackmount Series
22..22..11.. RReemmoovviinngg tthhee CCoovveerr
Page 7 of 14
ASUSTOR NAS Memory Installation Guide
• Shutdown the NAS by selecting [Shut down] from the ADM User Menu.
• Disconnect all cables and devices connected to the NAS including the power cord.
• Use a screwdriver to loosen the three screws found on the rear of the NAS as shown
in the illustration.
• Grip the cover from both sides with two hands and then gently push it back to
remove it from the chassis.
33..33..11 IInnssttaalllliinngg MMeemmoorryy
• When inserting the memory module into the empty slot, please make sure to align
the notches on the module with t h e notches in the slo t .
• Diagonally slide in the m emory module (as shown in the illustration) making sure
that the memory module’s connectors are fully inserted into the slot.
Page 8 of 14
ASUSTOR NAS Memory Installation Guide
• Using two fingers, carefully push down and then back on the memory module u nt il it
clicks into place. You should be able to hear an audible “click”.
33..33..22 RReeppllaacciinngg tthhee CCoovveerr
• Replace the cover and tighten the three screws that were removed previously.
Page 9 of 14
ASUSTOR NAS Memory Installation Guide
• Reconnect all cables including the power cord and then start up the NAS.
2.3. For AS7 Rackmount Series
22..33..11.. RReemmoovviinngg tthhee CCoovveerr
• Shutdown the NAS by selecting [Shut down] from the ADM User Menu.
• Disconnect all cables and devices connected to the NAS including the power cord.
Page 10 of 14
ASUSTOR NAS Memory Installation Guide
• Use a screwdriver to loosen the three screws found on the rear of the NAS as shown
in the illustration.
• Grip the cover from both sides with two hands and then gently push it back to
remove it from the chassis.
22..33..22.. IInnssttaalllliinngg MMeemmoorryy
• Release the ejector clips by gently pulling them out to the sides of the memory slot.
• When inserting the memory module into the empty slot, please make sure to align
the notches on the module with the notches in the slot.
• Slide in the memory module (as shown in the illustration) making sure that the
memory module’s connectors ar e fu l ly inserted into the slot.
Page 11 of 14
ASUSTOR NAS Memory Installation Guide
• Using two fingers, carefully push down on the memory mo dule until the ejector clips
lock it into place.
22..33..33.. RReeppllaacciinngg tthhee CCoovveerr
• Replace the cover and tighten the three screws that were removed previously.
Page 12 of 14
ASUSTOR NAS Memory Installation Guide
• Reconnect all cables incl uding the power cord and then start up the NAS.
Page 13 of 14
ASUSTOR NAS Memory Installation Guide
.
33.
AAppppeennddiixx
3.1. Troubleshooting
Q: After installing new memory my NAS won’t start. What’s wrong?
A: Please fo llow the steps below to resolve this issue:
1. Check if the LED indicators, system buzzer, and LCD display panel are operating
normally.
2. If your NAS is unable to recognize the new memory or cannot be started up properly,
please check that you have used memory that is compatible with the system. Also,
please reinstall the memory in order to confirm that it has been installed properly.
3. If your NAS still does not operate normally, please remove the newly installed memory
module, and then restart the NAS to see if it is able to operate normally.
4. If the previous steps have not solved your problem, please contact your local dealer or
ASUSTOR customer service.
3.2. Contact ASUSTOR Technical Support
Contact us:
1. Email: support@asustor.com
2. Online Support Form: http://www.asustor.com/service/online_support
3. ASUSTOR Online Community: http://forum.asustor.com/
Page 14 of 14
Loading...