No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
ASUS contact information .......................................................................A-5
iv
Chapter 1
Product overview
1.1 Package contents
Check your industrial motherboard package for the following items.
1 x ASUS Q470EI-IM-A Motherboard
2 x Serial ATA 6.0 Gb/s cables
2 x M.2 screw packages
1 x ASUS I/O Shield
NOTE: If any of the above items is damaged or missing, contact your
distributor or sales representative immediately.
1.2 Features
• Intel® socket 1200 for 10th Gen Intel® Core™ i9/ i7/ i5/ i3, Pentium®, and
Celeron® processors
• Two Dual Channel DDR4 2933/2666/2400/2133 MHz SO-DIMMs up to 64GB
• 3 x SATA 6.0 Gb/s, 3 x USB 3.2 Gen 2, 4 x USB 3.2 Gen 1, 6 x USB 2.0, 5 x
COM ports
• 1 x PCIe x16 slot, 1 x M.2 (Key E, 2230) for WiFi/BT device, 1 x M.2 (Key M,
2242/2260/2280) with PCIe and SATA modes for SSD
• Multi-display: 2 x DisplayPorts, 1 x DVI-D, LVDS/eDP
Chapter 1: General information
1-1
1.3 Specifications
Intel® socket 1200 for 10th Gen Intel® Core™ i9/ i7/ i5/ i3,
CPU
ChipsetIntel® Q470E Chipset
Memory
Graphics
Expansion slots
Storage
LANDual Intel® Lan: 1 x Intel® I219LM, 1 x Intel® I210AT
AudioRealtek ALC887 High Denition Audio
Rear panel I/O
ports
Pentium®, and Celeron® processors
Supports Intel® 14nm CPU
Supports up to 65W TDP
2 x SO-DIMM, max.64GB, DDR4 2933/2666/2400/2133 MHz
SDRAM
Integrated graphics processor - Intel® HD Graphics support
Multi-VGA output support: DP/DVI-D/LVDS ports
- Supports 2x DisplayPort 1.4a outputs with a maximum
resolution of 4096 x 2160 @60 Hz
- Supports DVI-D output with a maximum resolution of 1920 x
1200 @60Hz
- Supports LVDS output with a maximum resolution of 1920 x
1200 @60Hz
- 4 lanes Embedded Display Port output with a maximum
resolution of 3840 x 2160 @60Hz (co-lay with LVDS)
1 x PCI Express 3.0/2.0 x16 slot*
1 x M.2 socket 1 (Key E, 2230) with PCIe and CNVI modes for
WiFi/BT device
1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCIe and SATA
modes
* Supports PCIe bifurcation (16x to 8x+8x / 8x+4x+4x).
3 x SATA 6.0 Gb/s ports
1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCIe and SATA
modes
1 x DVI-D port
2 x DisplayPorts
3 x USB 3.2 Gen 2 ports (2 x Type-A + 1 x Type-C®)
1 x USB 3.2 Gen 1 port
4 x USB 2.0 ports
2 x LAN (RJ45) ports
1 x P/S2 keyboard port
1 x P/S2 mouse port
1 x COM port (RS232/422/485)
2 x Audio jacks
1-2
(continued on the next page)
Q470EI-IM-A
Internal I/O ports
GPIO
Manageability
Watch dog timer
Power
requirement
Operation
Temperature
Non-Operation
Temperature
4 x COM ports (1 x RS232/422/485, 3 x RS232)
1 x USB 3.2 Gen 1 connector supports additional 2 USB 3.2 Gen
1 ports
1 x USB 3.2 Gen 1 stick socket
1 x USB 2.0 connector supports additional 2 USB 2.0 ports
1 x CPU Fan connector with PWM mode
1 x Chassis Fan connector with PWM mode
1 x Disable ME connector
1 x LVDS/eDP Signal connector
1 x LVDS/eDP Backlight panel connector
1 x I2C connector
1 x LCD panel monitor switch header
1 x Front panel audio header (AAFP)
1 x System panel header
1 x S/PDIF connector
1 x Chassis intrusion header
1 x Speaker connector
1 x Clear CMOS header
1 x LPC Debug header
1 x AT/ATX mode selection header
1 x 24-pin ATX power connector
1 x 8-pin ATX power connector
1 x Display panel VCC power selection header
1 x M.2 socket 1 (Key E, 2230) with PCIe and CNVI modes for
WiFi/BT device
1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCIe and SATA
modes
1 x WDT_EN header
3 x SATA 6.0Gb/s connectors
1 x TPM connector
1 x RTC Battery connector
1 x LVDS/eDP Panel Enable Signal Selection header
1 x 8-bit GPIO header
WfM 2.0, DMI 2.0, WOL by PME
Yes
ATX mode
12V DC-IN (Supported by an additional cable)
0~60°C
-40~85°C
(continued on the next page)
Chapter 1: General information
1-3
Relative Humidity
OS support
Certification
Form Factor
NOTE: Specications are subject to change without notice.
0%~85%
Windows® 10 (64-bit)
Windows® IoT Enterprise
Ubuntu
RedHat Enterprise
Fedora Workstation
OpenSUSE
CE, FCC, UL
Mini-ITX Form Factor, 6.7”x 6.7” (17.0cm x 17.0cm)
1-4
Q470EI-IM-A
Chapter 2
Motherboard information
2.1 Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
CAUTION!
• Unplug the power cord from the wall socket before touching any
component.
• Before handling components, use a grounded wrist strap or touch a safely
grounded object or a metal object, such as the power supply case, to avoid
damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
• Before you install or remove any component, always remove the AC power
by unplugging the power cord from the power outlet. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Chapter 2: Motherboard information
2-1
2.2 Motherboard layout
NOTE: Place four screws into the holes indicated by circles to secure the
motherboard to the chassis.
CAUTION! Do not overtighten the screws! Doing so can damage the
motherboard.
BKLTEN_SEL
COM1
ALC
AAFP
LCD_BLKT_PANEL
EATX12V
PANEL_SW
VCC_PWR_SEL
BATTERYLVDS_EDP
WGI
210AT
U32G1_6
Intel
H310
WGI
219LM
887
CLRTC
242526
Place this side
towards the rear
of the chassis
32
31
30
29
28
27
CPU_FAN
KBMS
USB_9~12
DP_12
DVI
LAN2_U32G1_3
U32G2_C1
LAN1_U32G2_45
AUDIO
17.0cm(6.7in)
COM1_SEL
GPIO_CON
LGA1200
TPM
128Mb
BIOS
®
228022602242
PCIEX16
COM3
COM4
8 91 11 12 13 14103276541
WDT_EN
AT_ATX_SEL
COM5
Super
I/O
PCIE SATA IRST
X4 V
M.2(SOCKET3)
CHA_FAN
DIS_ME
SPEAKER
CHASSIS
F_PANEL
COM2
V
SPDIF_OUT
222320
COM2_SEL
EATXPWR
U32G1_78
DDR4 SO-DIMM_A1* (64bit, 260-pin module)
DDR4 SO-DIMM_B1* (64bit, 260-pin module)
M.2(WIFI)
M.2(SOCKET3)
USB_213
I2C
LPC_DEBUG
21
6
5
17.0cm(6.7in)
15
16
17
SATA6G_3SATA6G_2SATA6G_1
18
19
2-2
Q470EI-IM-A
Connectors/Jumpers/Slots
1.CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN)2-18
2.Display panel VCC power selection (6-pin VCC_PWR_SEL)2-10
32. LVDS/eDP Panel Enable Signal Selection header (3-pin BKLTEN_SEL)2-13
Page
Chapter 2: Motherboard information
2-3
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1200 socket designed for
the Intel® 10th Generation Intel® Core™ i9 / Core™ i7 / Core™ i5 / Core™ i3,
Pentium®, and Celeron® processors.
LGA1200
IMPORTANT! Unplug all power cables before installing the CPU.
CAUTION!
• Upon purchase of the motherboard, ensure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the
PnP cap/socket contacts/motherboard components. The manufacturer will
shoulder the cost of repair only if the damage is shipment/transit-related.
• Keep the cap after installing the motherboard. The manufacturer will
process Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA1200 socket.
• The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
2-4
Q470EI-IM-A
2.3.1 Installing the CPU
23
1
A
B
Chapter 2: Motherboard information
2-5
4
C
A
B
5
2-6
Q470EI-IM-A
2.3.2 CPU heatsink and fan assembly installation
CAUTION! Apply the Thermal
Interface Material to the CPU
heatsink and CPU before you
install the heatsink and fan if
necessary.
To install the CPU heatsink and fan assembly
1
A
B
B
A
34
2
Chapter 2: Motherboard information
2-7
To uninstall the CPU heatsink and fan assembly
1
2
A
B
B
A
2-8
Q470EI-IM-A
2.4 System memory
This motherboard comes with two Double Data Rate 4 (DDR4) Small Outline Dual Inline
Memory Module (SO-DIMM) sockets. The gure below illustrates the location of the DDR4
SO-DIMM sockets:
SO-DIMM_B1*
SO-DIMM_A1*
ChannelSockets
Channel ASO-DIMM_B1*
Channel BSO-DIMM_A1*
Recommended memory configuration
DIMM_A1*
DIMM_B1*
Installing a DIMM
12
To remove a DIMM
A
B
Chapter 2: Motherboard information
DIMM_B1*
DIMM_A1*
A
A
B
2-9
2.5 Jumpers
RI
(Default)
+5V+12V
COM1_SEL
COM2_SEL
123456
RI
(Default)
+5V+12V
1
2
3
4
5
6
A
A
B
B
1. Display panel VCC power selection (6-pin VCC_PWR_SEL)