No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language in any form or by any means, except documentation kept by the purchaser
for backup purposes, without the express written permission of ASUSTeK COMPUTER
INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED T O THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS,
OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA,
INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Product warranty or service will not be extended if: (1) the product is repaired, modified
or altered, unless such repair, modification of alteration is authorized in writing by
ASUS; or (2) the serial number of the product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
The product name and revision number are both printed on the product itself. Manual
revisions are released for each product design represented by the digit before and
after the period of the manual revision number. Manual updates are represented by
the third digit in the manual revision number.
For previous or updated manuals, BIOS, drivers, or product release information, contact
ASUS at http://www.asus.com.tw or through any of the means indicated on the following
page.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE
FURNISHED FOR INFORMA TIONAL USE ONLY , AND ARE SUBJECT T O CHANGE
AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A
COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY
FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Tel (English):+886-2-2890-7123
Tel (Chinese):+886-2-2890-7113
Fax:+886-2-2893-7775
Email:tsd@asus.com.tw
Newsgroup:news2.asus.com.tw
WWW:www.asus.com.tw
FTP:ftp.asus.com.tw/pub/ASUS
ASUS COMPUTER INTERNATIONAL (America)
Features
Marketing
Address:6737 Mowry Avenue, Mowry Business Center, Building 2
Newark, CA 94560, USA
Fax:+1-510-608-4555
Email:info-usa@asus.com.tw
This device complies with FCC Rules Part 15. Operation is subject to the
following two conditions:
•This device may not cause harmful interference, and
•This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor
to the graphics card is required to assure compliance with FCC
regulations. Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
The following checklist enumerates the components included in the
standard system package.
1)System Chassis
2)ASUS POLO Motherboard
3)Switching Power Supply
4)ASUS 24X CD-ROM Drive
5)CD-ROM Adapter Board
6)1.44MB Floppy Disk Drive
7)IR-USB Module
8)PCI Riser Card
9)CPU Heatsink
10)Motherboard Support CD
11)CD-ROM Drive Support Disk
12)(1) UltraDMA/33/66 IDE Cable
13)(1) UltraDMA/33 IDE Cable
14)(1) Floppy Cable
15)(1) IR Cable (5-pin)
16)(1) USB Cable (10-pin)
17)ASUS Name Plate
18)Motherboard User’s Manual
19)CD-ROM Drive Manual
20)Genie Book Size PC System Installation Guide
Optional Components (not included in standard system package)
1)56K PCI Modem Card
2)DFP Connector with Cable
3)(2) Foot Stands and (1) Plastic Panel Cover
If you are assembling the system by yourself, make sure to prepare
all the components before starting. It saves you a lot of time not having
to hunt down components when you need them.
6
Introduction
Y ou are reading the Genie Book Size PC
System Installation Guide. This reference
guide provides general information about
the Genie Book Size PC System.
“About This Guide” contains an
introduction on the contents of this
document that include target audience
and chapter description.
About This Guide
7Genie Book Size PC System
Audience
Checklist
This guide is intended for experienced users and integrators with
hardware knowledge of personal computers.
Contents Description
This installation guide contains the following parts:
1. Introduction: About This Guide
This part contains an introduction on the contents of this document
that include target audience and chapter description. It also lists
the items included in the system package.
2. Chapter 1: System Assembly
This chapter includes step-by-step instructions on how to install
components in the Genie Book Size PC System.
3. Chapter 2: Optional Procedures
This chapter tells how to install optional components and perform
optional assembly procedures in the Genie Book Size PC System.
4. Chapter 3: System Placement
This chapter describes the different system placement options to
allow you to maximize your working area and afford you more
convenience.
8Introduction: About This Manual
Loading...
+ 18 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.