Asus AP1600R-E2 User Manual

AP1600R-E2

(BA2/BI2)

1U Rackmount Barebone Server1U Rackmount Barebone Server

1U Rackmount Barebone Server

1U Rackmount Barebone Server1U Rackmount Barebone Server

User Guide

E1850E1850

E1850

E1850E1850

First Edition V2First Edition V2

First Edition V2

First Edition V2First Edition V2
August 2005August 2005

August 2005

August 2005August 2005

Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.

Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.

Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied, including
but not limited to the implied warranties or conditions of merchantability or fitness for a particular
purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any
indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of
business, loss of use or data, interruption of business and the like), even if ASUS has been advised
of the possibility of such damages arising from any defect or error in this manual or product.

Specifications and information contained in this manual ae furnished for informational use only, and
are subject to change at any time without notice, and should not be construed as a commitment by
ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in
this manual, including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered,
unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial
number of the product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks
or copyrights of their respective companies, and are used only for identification or explanation and
to the owners’ benefit, without intent to infringe.

ii

Contents

Notices ............................................................................................... vii

Safety information ............................................................................ viii

About this guide ................................................................................. ix

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

Chapter 1: Product introductionChapter 1: Product introduction

1.1 System package contents .................................................... 1-2

1.2 System specifications .......................................................... 1-3

1.3 Front panel features ............................................................. 1-4

1.4 Rear panel features .............................................................. 1-4

1.5 Internal features ................................................................... 1-5

1.6 LED information .................................................................... 1-6

1.6.1 Front panel LEDs .................................................... 1-6

1.6.2 Rear panel LEDs ...................................................... 1-6

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.1 Chassis cover ....................................................................... 2-2

2.1.1 Removing the cover................................................ 2-2

2.1.2 Installing the cover ................................................. 2-3

2.2 Central Processing Unit (CPU) .............................................. 2-4

2.2.1 Removing the CPU heatsink .................................... 2-4

2.2.2 Installling a CPU ...................................................... 2-5

2.2.3 Installing the CPU heatsink ..................................... 2-6

2.3 System memory ................................................................... 2-7

2.3.1 Overview ................................................................. 2-7

2.3.2 Memory configurations ........................................... 2-7

2.3.3 Installing a DIMM ..................................................... 2-8

2.3.4 Removing a DIMM ................................................... 2-8

2.4 Hard disk drives .................................................................... 2-9

2.4.1 Installing a SATA HDD (BA2 model) ....................... 2-9

2.4.2 Installing an IDE HDD (BI2 model) ........................ 2-11

2.5 Expansion slot .................................................................... 2-13

2.5.1 Installing an expansion card .................................. 2-13

2.5.2 Configuring an expansion card .............................. 2-15

2.6 Cable connections .............................................................. 2-16

2.7 Removable components ..................................................... 2-17

2.7.1 System fans .......................................................... 2-17

2.7.2 Device fan ............................................................. 2-17

..............................................

.......................

..............................................

............................................................

..............................

............................................................

1-11-1

1-1

1-11-1

2-12-1

2-1

2-12-1

iii

2.7.3 Power supply module ............................................ 2-18

2.7.4 Optical drive ......................................................... 2-19

2.7.5 Motherboard .........................................................2-21

2.8 SATA backplane cabling ..................................................... 2-24

Chapter 3: Installation optionsChapter 3: Installation options

Chapter 3: Installation options

Chapter 3: Installation optionsChapter 3: Installation options

3.1 Rackmount rail kit items ....................................................... 3-2

3.2 Rack rails assembly .............................................................. 3-2

3.3 Attaching the rails to the rack ............................................. 3-3

3.4 Rackmounting the server ..................................................... 3-4

Chapter 4: Motherboard informationChapter 4: Motherboard information

Chapter 4: Motherboard information

Chapter 4: Motherboard informationChapter 4: Motherboard information

4.1 Motherboard layout .............................................................. 4-2

4.2 Jumpers ................................................................................ 4-4

4.3 Connectors ........................................................................... 4-8

Chapter 5: BIOS SETUPChapter 5: BIOS SETUP

Chapter 5: BIOS SETUP

Chapter 5: BIOS SETUPChapter 5: BIOS SETUP

5.1 Managing and updating your BIOS ........................................ 5-2

5.1.1 Creating a bootable floppy disk .............................. 5-2

5.1.2 AFUDOS utility ........................................................ 5-3

5.1.3 ASUS CrashFree BIOS 2 utility ................................ 5-6

5.1.4 ASUS Update utility ................................................ 5-8

5.2 BIOS setup program ........................................................... 5-11

5.2.1 BIOS menu screen ................................................. 5-12

5.2.2 Menu bar ............................................................... 5-12

5.2.3 Navigation keys .................................................... 5-12

5.2.4 Menu items ...........................................................5-13

5.2.5 Sub-menu items ................................................... 5-13

5.2.6 Configuration fields .............................................. 5-13

5.2.7 Pop-up window ..................................................... 5-13

5.2.8 Scroll bar .............................................................. 5-13

5.2.9 General help .......................................................... 5-13

5.3 Main menu .......................................................................... 5-14

5.3.1 System Time [xx:xx:xxxx] .....................................5-14

5.3.2 System Date [Day xx/xx/xxxx] ............................ 5-14

5.3.3 Legacy Diskette A [1.44M, 3.5 in.]......................5-14

5.3.4 Primary, Third and Fourth IDE Master/Slave ......... 5-15

5.3.5 IDE Configuration .................................................. 5-16

5.3.6 System Information ..............................................5-17

........................................................................

....................................

........................................................................

..................................................

.........................

..................................................

..................................

.................

..................................

3-13-1

3-1

3-13-1

4-14-1

4-1

4-14-1

5-15-1

5-1

5-15-1

iv

5.4 Advanced menu .................................................................. 5-18

5.4.1 USB Configuration ................................................. 5-18

5.4.2 MPS Configuration ................................................ 5-19

5.4.3 Remote Access Configuration .............................. 5-20

5.4.4 CPU Configuration ................................................. 5-22

5.4.5 Chipset ................................................................. 5-23

5.4.6 Onboard Devices Configuration ............................ 5-24

5.4.7 PCI PnP ................................................................. 5-25

5.5 Power menu ........................................................................ 5-27

5.5.1 ACPI APIC Support [Enabled] ................................ 5-27

5.5.2 APM Configuration ................................................ 5-28

5.5.3 Hardware Monitor ................................................. 5-30

5.6 Boot menu .......................................................................... 5-32

5.6.1 Boot Device Priority .............................................. 5-32

5.6.2 Boot Settings Configuration .................................5-33

5.6.3 Security ................................................................ 5-34

5.7 Exit menu ........................................................................... 5-37

Chapter 6: Driver installationChapter 6: Driver installation

Chapter 6: Driver installation

Chapter 6: Driver installationChapter 6: Driver installation

6.1 RAID ...................................................................................... 6-2

6.1.1 RAID configurations ................................................ 6-2

6.1.2 Installing hard disk drives ....................................... 6-2

6.1.3 Setting the RAID item in BIOS ................................ 6-3

6.1.4 RAID configuration utility........................................ 6-3

6.1.5 Creating a RAID driver disk ...................................6-21

6.1.6 Installing the Intel® 6300ESB RAID controller

driver .................................................................... 6-22

6.2 LAN .................................................................................... 6-29

6.2.1 Windows® 2000/2003 Server ............................. 6-29

6.2.3 Red Hat® Linux 9.0 .............................................. 6-31

6.2.4 Novell NetWare Server ......................................... 6-33

6.2.5 Solaris ...................................................................6-36

6.2.6 UNIX ...................................................................... 6-38

6.3 VGA .................................................................................... 6-41

6.3.1 Windows® 2000 Server ....................................... 6-41

6.3.2 Windows® 2003 Server ....................................... 6-42

6.3.3 Red Hat® Linux 9.0 .............................................. 6-42

......................................................

...........................

......................................................

6-16-1

6-1

6-16-1

v

Notices

Federal Communications Commission StatementFederal Communications Commission Statement

Federal Communications Commission Statement

Federal Communications Commission StatementFederal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

•

This device may not cause harmful interference, and

•

This device must accept any interference received including interference
that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

WARNING!WARNING!

WARNING! The use of shielded cables for connection of the monitor to

WARNING!WARNING!
the graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.

Canadian Department of Communications StatementCanadian Department of Communications Statement

Canadian Department of Communications Statement

Canadian Department of Communications StatementCanadian Department of Communications Statement

This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.

This This

CC

lass lass

AA

This

This This

C

CC

digital apparatus complies with Canadian ICES-003. digital apparatus complies with Canadian ICES-003.

lass

A

digital apparatus complies with Canadian ICES-003.

lass lass

AA

digital apparatus complies with Canadian ICES-003. digital apparatus complies with Canadian ICES-003.

vi

Safety information

Electrical SafetyElectrical Safety

Electrical Safety

Electrical SafetyElectrical Safety

• Before installing or removing signal cables, ensure that the power cables
for the system unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.

• When adding or removing any additional devices to or from the system,
ensure that the power cables for the devices are unplugged before the
signal cables are connected. If possible, disconnect all power cables from
the existing system before you add a device.

• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your dealer.

Operation SafetyOperation Safety

Operation Safety

Operation SafetyOperation Safety

• Any mechanical operation on this server must be conducted by certified
or experienced engineers.

• Before operating the server, carefully read all the manuals included with
the server package.

• Before using the server, make sure all cables are correctly connected and
the power cables are not damaged. If any damage is detected, contact
your dealer as soon as possible.

• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a
stable surface.

This product is equipped with a three-wire power cable and plug for the
user’s safety. Use the power cable with a properly grounded electrical
outlet to avoid electrical shock.

Lithium-Ion Battery WarningLithium-Ion Battery Warning

Lithium-Ion Battery Warning

Lithium-Ion Battery WarningLithium-Ion Battery Warning

CAUTION!CAUTION!

CAUTION! Danger of explosion if battery is incorrectly replaced.

CAUTION!CAUTION!
Replace only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

CD-ROM Drive Safety WarningCD-ROM Drive Safety Warning

CD-ROM Drive Safety Warning

CD-ROM Drive Safety WarningCD-ROM Drive Safety Warning

CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT

CLASS 1 LASER PRODUCT

CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT

Heavy SystemHeavy System

Heavy System

Heavy SystemHeavy System

CAUTION!CAUTION!

CAUTION! This server system is heavy. Ask for assistance when

CAUTION!CAUTION!
moving or carrying the system.

vii

About this guide

AudienceAudience

Audience

AudienceAudience

This user guide is intended for system integrators, and experienced users
with at least basic knowledge of configuring a server.

ContentsContents

Contents

ContentsContents

This guide contains the following parts:

1.1.

Chapter 1: Product IntroductionChapter 1: Product Introduction

1.

Chapter 1: Product Introduction

1.1.

Chapter 1: Product IntroductionChapter 1: Product Introduction
This chapter describes the general features of the server, including

sections on front panel and rear panel specifications.

2.2.

Chapter 2: Hardware setupChapter 2: Hardware setup

2.

Chapter 2: Hardware setup

2.2.

Chapter 2: Hardware setupChapter 2: Hardware setup
This chapter lists the hardware setup procedures that you have to

perform when installing or removing system components.

3.3.

Chapter 3: Installation optionsChapter 3: Installation options

3.

Chapter 3: Installation options

3.3.

Chapter 3: Installation optionsChapter 3: Installation options
This chapter describes how to install optional components into the

barebone server.

4.4.

Chapter 4: Motherboard informationChapter 4: Motherboard information

4.

Chapter 4: Motherboard information

4.4.

Chapter 4: Motherboard informationChapter 4: Motherboard information
This chapter gives information about the motherboard that comes

with the server. This chapter includes the motherboard layout, jumper
settings, and connector locations.

5.5.

Chapter 5: BIOS informationChapter 5: BIOS information

5.

Chapter 5: BIOS information

5.5.

Chapter 5: BIOS informationChapter 5: BIOS information
This chapter tells how to change system settings through the BIOS

Setup menus and describes the BIOS parameters.

6.6.

Chapter 6: Driver installationChapter 6: Driver installation

6.

Chapter 6: Driver installation

6.6.

Chapter 6: Driver installationChapter 6: Driver installation
This chapter provides instructions for creating and configuring RAID,

and installing the necessary drivers for different system components.

viii

ConventionsConventions

Conventions

ConventionsConventions

To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.

WARNING: WARNING:

WARNING: Information to prevent injury to yourself when trying

WARNING: WARNING:
to complete a task.

CAUTION:CAUTION:

CAUTION: Information to prevent damage to the components

CAUTION:CAUTION:
when trying to complete a task.

IMPORTANT: IMPORTANT:

IMPORTANT: Instructions that you MUST follow to complete a

IMPORTANT: IMPORTANT:
task.

NOTE: NOTE:

NOTE: Tips and information to aid in completing a task.

NOTE: NOTE:

ReferencesReferences

References

ReferencesReferences

Refer to the following sources for additional information, and for product
and software updates.

1.1.

ASUS Server Web-based Management (ASWM) user guideASUS Server Web-based Management (ASWM) user guide

1.

ASUS Server Web-based Management (ASWM) user guide

1.1.

ASUS Server Web-based Management (ASWM) user guideASUS Server Web-based Management (ASWM) user guide
This manual tells how to set up and use the proprietary ASUS server

management utility.

2.2.

ASUS websitesASUS websites

2.

ASUS websites

2.2.

ASUS websitesASUS websites
The ASUS websites worldwide provide updated information for all

ASUS hardware and software products. Refer to the ASUS contact
information.

ix

x

Chapter 1

This chapter describes the general
features of the barebone server. It
includes sections on front panel and
rear panel specifications.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

Product introduction

1-1

1.1 System package contents

The items in the ASUS AP1600R-E2 (BA2/BI2) product package vary
depending on the model your purchased. Check your package for the
standard items listed in the following table.

Package items BA2 model BI2 model

ASUS AR14 1U rackmount chassis with:

• ASUS NCLV-D motherboard

• 500W power supply, 115V-230V

•SATA backplane

• Fan control board

• Optical drive

• System fan

• Device fan

•2 x internal HDD trays

• Pre-connected device/power cables
CPU heatsink (2 pcs.)

SA TA cable
IDE cable

Rackmount rail kit
Accessory box

• AP1600R-E2 drivers and utilities CD

• AP1600R-E2 user guide

•CA Anti-virus software CD

• Bag of screws

* BA2 model - supports up to two internal SATA hard disks
* BI2 model - supports up to two internal IDE hard disks

Contact your dealer immediately if any of the items is damaged or
missing.

1-21-2

1-2

1-21-2

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

Chapter 1: Product introductionChapter 1: Product introduction

1.2 System specifications

The ASUS AP1600R-E2 (BA2/BI2) is a 1U barebone server system
featuring the ASUS NCLV-D motherboard. The server supports dual Intel

®

Xeon™ processors, and includes the latest technologies through the
chipsets embedded on the motherboard.

ChassisChassis

Chassis Rackmount 1U (AR14)

ChassisChassis
MotherboardMotherboard

Motherboard ASUS NCLV-D

MotherboardMotherboard
ChipsetChipset

Chipset North Bridge: Intel

ChipsetChipset

ProcessorProcessor

Processor Supports dual Intel

ProcessorProcessor

MemoryMemory

Memory 4 x 184-pin DDR sockets for up to 16GB system memory

MemoryMemory

LANLAN

LAN Broadcom

LANLAN

VGAVGA

VGA ATI RAGE-XL PCI-based VGA controller

VGAVGA

Expansion slotsExpansion slots

Expansion slots 1 x PCI-X 66 MHz/64-bit slot (PCI-X 1.0)

Expansion slotsExpansion slots

StorageStorage

Storage Intel

StorageStorage

ManagementManagement

Management ASUS Server Web-based Management (ASWM)

ManagementManagement
Hardware monitorsHardware monitors

Hardware monitors Voltage, temperature, and fan speed monitoring

Hardware monitorsHardware monitors

Power supplyPower supply

Power supply 500W power supply, 115V~230V, 50Hz~60Hz

Power supplyPower supply
DimensionsDimensions

Dimensions 600 mm (l) x 445 mm (w) x 43.6 mm (h))

DimensionsDimensions

South Bridge: Intel® 6300ESB

and L3 1MB caches via two 604-pin sockets

Supports DDR 333 registered ECC DIMMs

Broadcom® BMC5705E 32-bit Gigabit LAN controller

Supports 8MB display memory

1 x Mini-PCI socket for the ASUS Server Management Board

®

6300ESB South Bridge supports:

- 2 x Ultra DMA 100/66/33 HDDs

- 2 x SATA HDDs with RAID 0/1 configuration

Automatic System Restart (ASR) feature

®

E7320 Memory Controller Hub (MCH)

®

Xeon™ 3.6 GHz processors with L2 1MB

®

BMC5721 64-bit Gigabit LAN controller

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

1-31-3

1-3

1-31-3

1.3 Front panel features

The front panel displays a simple yet stylish front panel with easily
accessible features. The power and reset buttons, LED indicators, location
switch, optical drive, and two USB ports are located on the front panel.

Rack screwRack screw

Rack screw

Rack screwRack screw

USB portsUSB ports

USB ports

USB portsUSB ports

HDD Access LEDHDD Access LED

HDD Access LED

HDD Access LEDHDD Access LED

LAN2 LEDLAN2 LED

LAN2 LED

LAN2 LEDLAN2 LED
LAN1 LEDLAN1 LED

LAN1 LED

LAN1 LEDLAN1 LED

HDD baysHDD bays

HDD bays

HDD baysHDD bays

Power buttonPower button

Power button

Power buttonPower button
Power LEDPower LED

Power LED

Power LEDPower LED
Location switchLocation switch

Location switch

Location switchLocation switch
Location LEDLocation LED

Location LED

Location LEDLocation LED
Reset buttonReset button

Reset button

Reset buttonReset button

Optical driveOptical drive

Optical drive

Optical driveOptical drive

Rack screwRack screw

Rack screw

Rack screwRack screw

Message LED

Refer to section “1.6.1 Front panel LEDs” for the LED descriptions.

1.4 Rear panel features

The rear panel includes the expansion slot, system power socket, and rear
fans. The middle part includes the I/O shield with openings for the rear
panel connectors on the motherboard.

The ports for the PS/2 keyboard, PS/2 mouse, USB, VGA, and Gigabit
LAN do not appear on the rear panel if motherboard is not present.

1-41-4

1-4

1-41-4

A

A

A

A

A
C

C

C

C

C
p

p

p

p

p
o

o

o

o

o
w

w

w

w

w
e

e

e

e

e
r

r

r

r

r
s

s

s

s

s
o

o

o

o

o
c

c

c

c

c
k

k

k

k

k
e

e

e

e

e
t

t

t

t

t

R

R

R

PS/2 mouse port

R

R

PS/2 mouse portPS/2 mouse port

PS/2 mouse portPS/2 mouse port

e

e

e

e

e
a

a

a

a

a
r

r

r

r

r
f

f

f

f

f
a

a

a

a

a
n

n

n

n

n
s

s

s

s

s

U

U

PS/2 keyboard port

U

U

U

PS/2 keyboard portPS/2 keyboard port

PS/2 keyboard portPS/2 keyboard port

S

S

S

S

S
B

B

B

B

B
p

p

p

p

p
o

o

o

o

o
r

r

r

r

r
t

t

t

t

t
s

s

s

s

s

V

V

V

V

V

S

S

S

S

S
e

e

e

e

e
r

r

r

r

r
ia

ia

ia

ia

ia
l

l

l

l

l
p

p

p

p

p
o

o

o

o

o
r

r

r

r

r
t

t

t

t

t

LAN port1

LAN port2

LAN port1LAN port1

LAN port1LAN port1

LAN port2LAN port2

LAN port2LAN port2

G

G

G

G

G
A

A

A

A

A
p

p

p

p

p
o

o

o

o

o
r

r

r

r

r
t

t

t

t

t

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

Chapter 1: Product introductionChapter 1: Product introduction

Parallel port

Parallel portParallel port

Parallel portParallel port

Expansion slot

Expansion slotExpansion slot

Expansion slotExpansion slot

1.5 Internal features

The barebone system includes the basic components as shown.

2

1

3

5

7

8

1. PCI-X riser card bracket

2. Rear fans

3. NCLV-D motherboard

4. Power supply

5. Device fan

The barebone server does not include a floppy disk drive. Connect an
external floppy disk drive (USB interface) to any of the USB ports on the
front or rear panel if you need to use a floppy disk.

4

6

9

10

6. System fans

7. SATA backplane

8. Hot-swap HDD tray 1

9. Hot-swap HDD tray 2

10. Optical drive

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

1-51-5

1-5

1-51-5

1.6 LED information

1.6.11.6.1

1.6.1

1.6.11.6.1

Front panel LEDsFront panel LEDs

Front panel LEDs

Front panel LEDsFront panel LEDs

HDD Access LEDHDD Access LED

HDD Access LED

HDD Access LEDHDD Access LED

LAN2 LEDLAN2 LED

LAN2 LED

LAN2 LEDLAN2 LED

LAN1 LEDLAN1 LED

LAN1 LED

LAN1 LEDLAN1 LED

LEDLED

LED

LEDLED

Power LED ON System power ON
HDD Access LED OFF No activity

Message LED OFF System is normal; no incoming event

Location LED OFF Normal status

LAN LEDs OFF No LAN connection

Display statusDisplay status

Display status

Display statusDisplay status

Blinking Read/write data into the HDD

Blinking ASWM indicates a HW monitor event

ON Location switch is pressed

Blinking LAN is transmitting or receiving data
ON LAN connection is present

Message LEDMessage LED

Message LED

Message LEDMessage LED

DescriptionDescription

Description

DescriptionDescription

(Press the location switch again to turn off)

Power LEDPower LED

Power LED

Power LEDPower LED

Location LEDLocation LED

Location LED

Location LEDLocation LED

1-61-6

1-6

1-61-6

1.6.21.6.2

1.6.2

1.6.21.6.2

Rear panel LEDsRear panel LEDs

Rear panel LEDs

Rear panel LEDsRear panel LEDs

RJ-45

ACT/LINK LEDACT/LINK LED

ACT/LINK LED

ACT/LINK LEDACT/LINK LED

Status Description Status Description

OFF No link OFF 10Mbps connection
Green Linked Orange 100Mbps connection
Blinking Linking Green 1000Mbps connection

SPEED LEDSPEED LED

SPEED LED

SPEED LEDSPEED LED

Chapter 1: Product introductionChapter 1: Product introduction

Chapter 1: Product introduction

Chapter 1: Product introductionChapter 1: Product introduction

SPEEDACT/LNK

Chapter 2

This chapter lists the hardware
setup procedures that you have to
perform when installing or removing
system components.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

Hardware setup

2-1

2.1 Chassis cover

2.1.12.1.1

2.1.1

2.1.12.1.1

Removing the coverRemoving the cover

Removing the cover

Removing the coverRemoving the cover

1. Use a Phillips screwdriver to remove the screw on each front end of
the top cover.

ThumbscrewsThumbscrews

Thumbscrews

ThumbscrewsThumbscrews

2. Loosen the two thumbscrews on
the rear panel to release the top
cover from the chassis.

3. Firmly hold the cover and slide it
toward the rear panel for about
half an inch until it is disengaged
from the chassis.

4. Lift the cover from the chassis.

2-22-2

2-2

2-22-2

1/2 inch distance1/2 inch distance

1/2 inch distance

1/2 inch distance1/2 inch distance

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.1.22.1.2

2.1.2

2.1.22.1.2

Installing the coverInstalling the cover

Installing the cover

Installing the coverInstalling the cover

1. Position the cover on top of the chassis with the thumbscrews on the
rear, and leaving a gap of about half an inch from the front panel.

Side markingsSide markings

Side markings

Side markingsSide markings

2. Make sure that the side markings on the cover (two on each side) are
aligned to the grooves on the chassis.

GroovesGrooves

Grooves

GroovesGrooves

3. Slide the cover toward the front until it snaps in place.

4. Tighten the thumbscrews on the rear to secure the cover.

ThumbscrewsThumbscrews

Thumbscrews

ThumbscrewsThumbscrews

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

2-32-3

2-3

2-32-3

2.2 Central Processing Unit (CPU)

The motherboard comes with two surface mount 604-pin Zero Insertion
Force (ZIF) socket and designed for the Intel® Xeon™ processors.

NCLV-D

NCLV-D CPU Socket 604

1. The motherboard supports either one or two CPUs. If you are
installing only one CPU, you MUST install it in CPU socket 1.

2. If you are installing two CPUs, install in the CPU socket 2 first.

2.2.12.2.1

2.2.1

2.2.12.2.1

Removing the CPU heatsinkRemoving the CPU heatsink

Removing the CPU heatsink

Removing the CPU heatsinkRemoving the CPU heatsink

Intel Xeon

Gold Arrow
Pin A1

If you have previously installed CPUs and heatsinks, follow these steps to
remove the heatsinks before proceeding to the next section.

To remove the CPU heatsink:

1. Use a Phillips (cross) screwdriver
to loosen the four screws that
secure the heatsink until it is
released.

2. Carefully lift the heatsink from
the motherboard.

2-42-4

2-4

2-42-4

You don’t need to detach the screws from the heatsink.

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.2.22.2.2

2.2.2

2.2.22.2.2

Installling a CPUInstallling a CPU

Installling a CPU

Installling a CPUInstallling a CPU

To install the CPUs:

1. Locate the CPU sockets on the
motherboard. Flip up the socket
lever and push it all the way to
the other side.

2. Carefully insert the CPU into the
socket as shown until it fits in
place.

The CPU fits only in one
correct orientation. DO NOT
force the CPU into the socket
to prevent bending the pins
and damaging the CPU!

Socket for CPU1Socket for CPU1

Socket for CPU1

Socket for CPU1Socket for CPU1

3. Carefully push down the socket
lever to secure the CPU. The
lever clicks on the side tab to
indicate that it is locked.

4. Apply the thermal interface
material (thermal grease) to the
top of the CPU. This thermal
grease should come with the CPU
package.

5. Repeat steps 1 to 4 if you wish
to install a second CPU.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

Marked cornerMarked corner

Marked corner

Marked cornerMarked corner
(gold arrow)(gold arrow)

(gold arrow)

(gold arrow)(gold arrow)

2-52-5

2-5

2-52-5

2.2.32.2.3

2.2.3

2.2.32.2.3

To install the CPU heatsink:

1. Carefully place the heatsink on

2. Twist each of the four screws

Installing the CPU heatsinkInstalling the CPU heatsink

Installing the CPU heatsink

Installing the CPU heatsinkInstalling the CPU heatsink

top of the installed CPU (CPU1).

with a Philips (cross) screwdriver
just enough to attach the
heatsink to the motherboard.
When the four screws are
attached, tighten them one by
one to completely secure the
heatsink.

3. Follow steps 1 and 2 to install
the second CPU heatsink.

2-62-6

2-6

2-62-6

Heatsink for CPU2

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.3 System memory

2.3.12.3.1

2.3.1

2.3.12.3.1

OverviewOverview

Overview

OverviewOverview

The motherboard comes with four Double Data Rate (DDR) Dual Inline
Memory Modules (DIMM) sockets. These sockets support up to 16 GB
system memory using 184-pin registered ECC DDR 333 DIMMs.

NCLV-D

NCLV-D 184-Pin DDR DIMM sockets

2.3.22.3.2

2.3.2

2.3.22.3.2

Memory configurationsMemory configurations

Memory configurations

Memory configurationsMemory configurations

80 Pins104 Pins

DDR_B2
DDR_A2
DDR_B1
DDR_A1

You may install 256 MB, 512 MB, 1 GB, 2GB, and 4GB registered ECC DDR
DIMMs into the DIMM sockets.

• Always install DIMMs with the same CAS latency. For optimum
compatibility, it is recommended that you obtain memory modules
from the same vendor. Refer to the DDR Qualified Vendors List on
the following URL for details.

• Due to chipset resource allocation, the system may detect less than
16 GB system memory when you installed four 4 GB DDR memory
modules.

• This motherboard does not support memory modules made up of
128 Mb chips or double sided x16 memory modules.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

2-72-7

2-7

2-72-7

2.3.32.3.3

2.3.3

2.3.32.3.3

Installing a DIMMInstalling a DIMM

Installing a DIMM

Installing a DIMMInstalling a DIMM

Make sure to unplug the power supply before adding or removing DIMMs
or other system components. Failure to do so may cause severe damage
to both the motherboard and the components.

1. Unlock a DIMM socket by
pressing the retaining clips
outward.

2. Align a DIMM on the socket such
that the notch on the DIMM
matches the break on the
socket.

A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.

3. Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.

2

DDR DIMM notchDDR DIMM notch

DDR DIMM notch

DDR DIMM notchDDR DIMM notch

1

1

Unlocked retaining clipUnlocked retaining clip

Unlocked retaining clip

Unlocked retaining clipUnlocked retaining clip

2.3.42.3.4

2.3.4

2.3.42.3.4

Removing a DIMMRemoving a DIMM

Removing a DIMM

Removing a DIMMRemoving a DIMM

Follow these steps to remove a DIMM.

1. Simultaneously press the
retaining clips outward to unlock
the DIMM.

Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.

2. Remove the DIMM from the socket.

2-82-8

2-8

2-82-8

Locked Retaining ClipLocked Retaining Clip

Locked Retaining Clip

Locked Retaining ClipLocked Retaining Clip

2

1

DDR DIMM notchDDR DIMM notch

DDR DIMM notch

DDR DIMM notchDDR DIMM notch

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

1

2.4 Hard disk drives

2.4.12.4.1

2.4.1

2.4.12.4.1

To install a SATA HDD:

1. Release a drive tray by pushing

2. Firmly hold the tray lever and

3. Take note of the drive tray

Installing a SATA HDD Installing a SATA HDD

Installing a SATA HDD

Installing a SATA HDD Installing a SATA HDD

the spring lock to the right, then
pulling the tray lever outward.
The drive tray ejects slightly
after you pull out the lever.

pull the drive tray out of the
bay.

holes. Each side has three holes
to fit different types of hard disk
drives. Use two screws on each
side to secure the hard disk
drive.

(BA2 model)(BA2 model)

(BA2 model)

(BA2 model)(BA2 model)

4. Place a SATA hard disk drive on
the tray, then secure it with four
screws.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

2-92-9

2-9

2-92-9

5. Carefully insert the drive tray
and push it all the way to the
depth of the bay until just a
small fraction of the tray edge
protrudes.

When installed, the SATA connector on the drive connects to the SATA
interface on the backplane.

6. Push the tray lever until it clicks,
and secures the drive tray in
place. The drive tray is correctly
placed when its front edge aligns
with the bay edge.

7. Repeat steps 1 to 6 if you wish
to install a second SATA drive.

SATA interfaceSATA interface

SATA interface

SATA interfaceSATA interface
on the backplaneon the backplane

on the backplane

on the backplaneon the backplane

8. Connect the bundled SATA cables to the connectors on the SATA
backplane. Refer to section “2.7 SATA backplane cabling” for
information on the SATA backplane cable connections.

2-102-10

2-10

2-102-10

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.4.22.4.2

2.4.2

2.4.22.4.2

To install an IDE HDD:

1. Disconnect all the cables from

2. Remove the screw that secures

Installing an IDE HDD Installing an IDE HDD

Installing an IDE HDD

Installing an IDE HDD Installing an IDE HDD

the fan control board. Use a
Phillips (cross) screwdriver to
remove the five screws that
secure the fan control board.

Fan control board screwsFan control board screws

Fan control board screws

Fan control board screwsFan control board screws

the hard disk tray to the chassis.
Slide the tray backward until the
two tray lock tabs are
disengaged. Lift the tray from
the bay.

(BI2 model)(BI2 model)

(BI2 model)

(BI2 model)(BI2 model)

Lock tab

3. Place a hard disk drive on the
drive tray, and secure it with
four screws.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

2-112-11

2-11

2-112-11

4. Carefully place the tray with
installed hard disk drive into the
drive bay. Slide it forward until
the front end aligns with the
front panel, and the screw hole
matches the standoff.

5. Secure the tray with a screw.

6. Repeat steps 2 to 5 if you wish
to install a second HDD;
otherwise, proceed to step 7.

7. Reinstall the fan control board.
Secure the board with five
screws.

8. Connect the 40-pin IDE cable
and a 4-pin power plug to their
respective connectors on the
back of the drive.

The other end of the IDE cable is pre-connected to the primary IDE
connector on the motherboard.

2-122-12

2-12

2-122-12

40-pin IDE cable40-pin IDE cable

40-pin IDE cable

40-pin IDE cable40-pin IDE cable

4-pin power plug4-pin power plug

4-pin power plug

4-pin power plug4-pin power plug

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup

2.5 Expansion slot

2.5.12.5.1

2.5.1

2.5.12.5.1

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Installing an expansion cardInstalling an expansion card

The barebone server comes with a riser card bracket. You need to remove
the bracket if you wish to install a PCI-X expansion card.

To install a PCI-X card:

1. Use a Phillips (cross) screwdriver to remove the screw that secures
the riser card to the standoff.

Riser card screwRiser card screw

Riser card screw

Riser card screwRiser card screw

Riser card standoffRiser card standoff

Riser card standoff

Riser card standoffRiser card standoff

2. Firmly hold a riser card bracket,
then pull it up to detach it from
the PCI-X slot on the
motherboard.

3. Remove the screw that secures
the slot metal cover.

4. Install a PCI-X card to the
bracket as shown, then secure
the card with a screw.

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)

ASUS AP1600R-E2 (BA2/BI2)ASUS AP1600R-E2 (BA2/BI2)

2-132-13

2-13

2-132-13

5. Take note of the holes on the
riser card bay. The two pegs on
the riser card bracket should
match these holes to ensure
that the bracket is properly in
place.

Peg on the riserPeg on the riser

Peg on the riser

Peg on the riserPeg on the riser
card bracketcard bracket

card bracket

card bracketcard bracket

6. Install the riser card bracket with
the card into the PCI-X slot on
the motherboard.

7. Make sure that the golden
connectors completely fit the
slot and the bracket aligns with
the rear panel.

8. Secure the riser card to the
standoff.

9. Connect the cable(s) to the
card, if applicable.

2-142-14

2-14

2-142-14

Chapter 2: Hardware setupChapter 2: Hardware setup

Chapter 2: Hardware setup

Chapter 2: Hardware setupChapter 2: Hardware setup