ASUS A40JC User Manual

Copyright Notice:Copyright Notice:
Copyright Notice:
Copyright Notice:Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documen­tation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identifica­tion or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:
Disclaimer:Disclaimer:
Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published April 2007
Copyright©2007 ASRock INC. All rights reserved.
ASRock ConRoe1333-eSATA2 Motherboard
EnglishEnglish
EnglishEnglish
English
11
1
11
Motherboard LMotherboard L
Motherboard L
Motherboard LMotherboard L
ayoutayout
ayout
ayoutayout
English
EnglishEnglish
EnglishEnglish
22
2
22
1 PS2_USB_PWR1 Jumper 19 SA T AII Connector (SATAII_BLUE (PORT0)) 2 A TX 12V Connector (A TX12V1) 20 USB 2.0 Header (USB67, Blue) 3 SLI / XFIRE Power Connector 21 SA T AII Connector (SATAII_RED (PORT2)) 4 775-Pin CPU Socket 22 South Bridge Controller 5 North Bridge Controller 23 USB 2.0 Header (USB45, Blue) 6 CPU Fan Connector (CPU_FAN1) 24 USB 2.0 Header (USB23, Blue) 7 2 x 240-pin DDRII DIMM Slots 25 Front Panel IEEE 1394 Header (FRONT_1394)
(Dual Channel A: DDRII_1, DDRII_3; Yellow) 26 Floppy Connector (FLOPPY1)
8 2 x 240-pin DDRII DIMM Slots 27 Game Port Header (GAME1)
(Dual Channel B: DDRII_2, DDRII_4; Orange) 28 Internal Audio Connector: CD1 (Black) 9 PCI Express x16 Slot (PCIE1) 29 Front Panel Audio Header (HD_AUDIO1) 10 Clear CMOS Jumper (CLRCMOS1) 30 HDMI_SPDIF Header (HDMI_SPDIF1) 11 Infrared Module Connector (IR1) 31 Back Panel IEEE 1394 Header (BACK_1394) 12 Chassis Fan Connector (CHA_FAN1) 32 PCI Slots (PCI1- 3) 13 BIOS FWH Chip 33 AGI Express Slot (PCI Express x4) 14 Chassis Speaker Header (SPEAKER 1) 34 PCI Express x1 Slot (PCIE2) 15 SATAII Connector (SAT AII_ORANGE (PORT3)) 35 ATX Power Connector (A TXPW R1) 16 IDE1 Connector (IDE1, Blue) 36 eSATAII Connector (eSATAII_BOTTOM) 17 SATAII Connector (SAT AII_BLACK (PORT1)) 37 eSATAII Connector (eSATAII_TOP) 18 System Panel Header (PANEL1)
ASRock ConRoe1333-eSATA2 Motherboard
ASRASR
ock 8CH_eSock 8CH_eS
ASR
ock 8CH_eS
ASRASR
ock 8CH_eSock 8CH_eS
1 Parallel Port 8 Microphone (Pink) 2 RJ-45 Port 9 USB 2.0 Ports (USB01) 3 Side Speaker (Gray) 10 eSATAII Ports 4 Rear Speaker (Black) 11 COM Port 5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple) 6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)
*7 Front Speaker (Lime)
* If you use 2-channel spea ker, please connect the speaker’s plug into “Front Speaker Jack”. See
the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker
2 V -- -- -­4VV---­6 VVV-­8 VVVV
AA
TT
AII I/OAII I/O
A
T
AII I/O
AA
TT
AII I/OAII I/O
(No. 7) (No. 4) (No. 5) (No. 3)
* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.
Free Bundle
ASRock provides you with one USB+1394 bracket, which can support 2 additional USB 2.0 ports and 1 IEEE 1394 port.
ASRock ConRoe1333-eSATA2 Motherboard
EnglishEnglish
EnglishEnglish
English
33
3
33
1. Introduction1. Introduction
1. Introduction
1. Introduction1. Introduction
Thank you for purchasing ASRock ConRoe1333-eSATA2 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It de­livers excellent performance with robust design conforming to ASRock’s commit­ment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-by­step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website
1.1 Package Contents1.1 Package Contents
1.1 Package Contents
1.1 Package Contents1.1 Package Contents
ASRock ConRoe1333-eSATA2 Motherboard
(ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm) ASRock ConRoe1333-eSATA2 Quick Installation Guide ASRock ConRoe1333-eSATA2 Support CD One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive Four Serial AT A (SAT A) Data Cables (Optional) Two Serial ATA (SATA) HDD Power Cables (Optional) One HDMI_SPDIF Cable (Optional) One ASRock 8CH_eSATAII I/O Pa nel Shield One USB+1394 Bracket
http://www.asrock.com
English
EnglishEnglish
EnglishEnglish
44
4
44
ASRock ConRoe1333-eSATA2 Motherboard
1.21.2
SpecificationsSpecifications
1.2
Specifications
1.21.2
SpecificationsSpecifications
Platform - ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm CPU - LGA 775 for Intel® Dual Core CoreTM 2 Extreme / CoreTM 2 Duo
/ Pentium® D / Pentium® Dual Core / Pentium® 4 / Celeron® / Celeron® D
- Compatible with all FSB1333/1066/800/533MHz CPUs except Quad Core (see CAUTION 1)
- Supports Hyper-Threading Technology (see CAUTION 2)
- Supports Untied Overclocking Technology (see CAUTION 3)
- Supports EM64T CPU
Chipset - Northbridge: Intel® 945P/945G
- Southbridge: Intel® ICH7R
Memory - Dual Channel DDRII Memory T echnology (see CAUTION 4)
- 4 x DDRII DIMM slots
- Support DDRII667/533 (see CAUTION 5)
- Max. capacity: 4GB (see CAUTION 6)
Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 7)
- ASRock U-COP (see CAUTION 8)
- Boot Failure Guard (B.F.G.)
Expansion Slot - Supports ATI
- 3 x PCI slots
- 1 x PCI Express x16 slot
- 1 x AGI Express slot (PCI Express x4)
- 1 x PCI Express x1 slot
Audio - 7.1 CH Windows® VistaTM Premium Level HD Audio
(ALC888 Audio Codec)
LAN - PCIE x1 Giga bit LAN 10/100/1000 Mb/s
- Realtek RTL8111B
- Supports Wake-On-LAN
Rear Panel I/O ASRock 8CH_eSATAII I/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP Support)
- 2 x Ready-to-Use USB 2.0 Ports
- 2 x eSATAII Ports
- 1 x RJ-45 Port
- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/ Line in/Front Speaker/Microphone (see CAUTION 9)
TM
CrossFire
TM
EnglishEnglish
EnglishEnglish
English
ASRock ConRoe1333-eSATA2 Motherboard
55
5
55
English
EnglishEnglish
EnglishEnglish
Free Bundle: USB+1394 bracket, providing 2 additional USB 2.0 ports and 1 IEEE 1394 port
Connector - 4 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 10, RAID 5 and Intel Matrix Storage), NCQ, AHCI and “Hot Plug” functions (see CAUTION 10)
- 2 x eSATAII 3.0Gb/s connectors (shared with 2 SATAII connectors), support “Hot Plug” function (see CAUTION 11)
- 1 x ATA100 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
- 1 x Game header
- 1 x HDMI_SPDIF header
- 2 x IEEE 1394 headers
- CPU/Chassis FAN connector
- 20 pin ATX power connector
- 4 pin 12V power connector
- SLI/XFIRE power connector
- CD in header
- Front panel audio connector
- 3 x USB 2.0 headers (support 6 USB 2.0 ports) (see CAUTION 12)
BIOS Feature - 4Mb AMI BIOS
- AMI Legal BIOS
- Supports “Plug and Play”
- ACPI 1.1 Compli ance Wake Up Events
- Supports jumperfree
- AMBIOS 2.3.1 Support Support CD - Drivers, Utilities, AntiVirus Software (Trial Version) Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft® Windows® 2000/XP/XP 64-bit/VistaTM/
VistaTM 64-bit compliant (see CAUTION 13)
Certifications - FCC, CE, WHQL
66
6
66
ASRock ConRoe1333-eSATA2 Motherboard
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third­party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
CAUTION!
1. FSB1333-CPU will operate in overclocking mode. Under this situation, PCIE frequency will also be overclocked to 115MHz.
2. About the setting of “Hyper Threading Technology”, please check page 48 of “User Manual” in the support CD.
3. This motherboard supports Untied Overclocking Technology. Please read “Untied Overclocking Technology” on page 37 for details.
4. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 12 for proper installation.
5. Please check the table below for the CPU FSB frequency and its corre­sponding memory support frequency.
CPU FSB Frequency Memory Support Frequency
1333 DDRII533*, DDRII667 1066 DDRII533, DDRII667
800 DDRII400, DDRII533, DDRII667 533 DDRII400, DDRII533
* When you use a FSB1333-CPU on this motherboard, it will run at
DDRII500 if you adopt a DDRII533 memory module.
6. Due to the chipset limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 2000, Win­dows® XP, Windows® XP 64-bit, Windows® VistaTM and Windows® Vista 64-bit.
7. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.
8. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU a nd the he atsink when you in stall the PC system.
9. For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.
TM
EnglishEnglish
EnglishEnglish
English
ASRock ConRoe1333-eSATA2 Motherboard
77
7
77
10. Before installing SATAII hard disk to SATAII connector, please read the “SATAII Hard Disk Setup Guide” on page 29 to a djust your SATAII hard disk drive to SATAII mode. You can also connect SATA hard disk to SATAII connector directly.
11. This motherboard supports eSATAII interface, the external SATAII specification. Please read “eSATAII Interface Introduction” on page 26 for details about eSATAII and eSATAII installation procedures.
12. Power Management for USB 2.0 works fine under Microsoft® Windows VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
13. Microsoft® Windows® VistaTM / VistaTM 64-bit driver keeps on updating now. As long as we have the latest driver, we will update it to our website in the future. Please visit our website for Microsoft® Windows® VistaTM / VistaTM 64-bit driver and related information. ASRock website http://www.asrock.com
1.31.3
Minimum Hardware RMinimum Hardware R
1.3
Minimum Hardware R
1.31.3
Minimum Hardware RMinimum Hardware R
TMTM
TM
TMTM
VistaVista
Vista
VistaVista
For system integrators and users who purchase this motherboard and plan to submit Windows® VistaTM Premium 2007 and Basic logo, please follow below table for minimum hardware requirements.
CPU Celeron D 326 Memory 1GB system memory (Premium)
VGA DX9.0 with WDDM Driver
Premium 2007 and Basic Logo Premium 2007 and Basic Logo
Premium 2007 and Basic Logo
Premium 2007 and Basic Logo Premium 2007 and Basic Logo
512MB Single Channel (Ba sic)
with 128bit VGA memory (Premium) with 64bit VGA memory (Basic)
equirement Tequirement T
equirement T
equirement Tequirement T
able for Wable for W
able for W
able for Wable for W
®
indowsindows
indows
indowsindows
®®
®
®®
English
EnglishEnglish
EnglishEnglish
88
8
88
* After June 1, 2007, all Windows® VistaTM systems are required to meet above minimum hardware requirements in order to qualify for Windows® VistaTM Premium 2007 logo.
ASRock ConRoe1333-eSATA2 Motherboard
2.2.
InstallationInstallation
2.
Installation
2.2.
InstallationInstallation
Pre-installation PrecautionsPre-installation Precautions
Pre-installation Precautions
Pre-installation PrecautionsPre-installation Precautions
Take note of the following precautions before you install mother­board components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.
2.12.1
CPU InstallationCPU Installation
2.1
CPU Installation
2.12.1
CPU InstallationCPU Installation
For the installation of Intel 775-LAND CPU, please follow the steps below.
775-Pin Socket Overview
Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
ASRock ConRoe1333-eSATA2 Motherboard
EnglishEnglish
EnglishEnglish
English
99
9
99
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear retention tab.
Step 1-2. Rotate the load lever to fully open po-
sition at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open po-
sition at approximately 100 degrees.
Step 2. Insert the 775-LAND CPU:
Step 2-1. Hold the CPU by the edges where are
marked with black lines.
Step 2-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two orientation key notches.
Pin1
orientation
key notch
orientation
key notch
Pin1
alignment key
black line
black line
alignment key
English
EnglishEnglish
EnglishEnglish
1010
10
1010
775-Pin Socket
775-LAND CPU
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully pla ce the CPU into the socket
by using a purely vertical motion.
Step 2-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 3. Remove PnP Cap (Pick and Place Cap):
Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
ASRock ConRoe1333-eSATA2 Motherboard
1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
2. This cap must be placed if returning the motherboard for after service.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
2.22.2
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
2.2
Installation of CPU Fan and Heatsink
2.22.2
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Step 1. Apply thermal interface material onto center
of IHS on the socket surface.
Step 2. Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_FAN1, see page 2, No. 6).
Step 3. Align fasteners with the motherboard
throughholes.
Step 4. Rotate the fastener clockwise, then press
down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
Step 5. Connect fan header with the CPU fan
connector on the motherboard.
Step 6. Secure excess cable with tie-wrap to ensure
cable does not interfere with fan operation or contact other components.
ASRock ConRoe1333-eSATA2 Motherboard
1111
11
1111
EnglishEnglish
EnglishEnglish
English
2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)
2.3 Installation of Memory Modules (DIMM)
2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)
ConRoe1333-eSATA2 motherboard provides four 240-pin DDRII (Double Data Rate II) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDRII DIMM pair in the slots of the sa me color. In other words, you have to install identical DDRII DIMM pair in Dual Cha nnel A (DDRII_1 and DDRII_3; Yellow slots; see p.2 No.7) or identical DDRII DIMM pair in Dual Channel B (DDRII_2 and DDRII_4; Orange slots; see p.2 No.8), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDRII DIMMs for dual channel configuration, and please install identical DDRII DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration Table below.
Dual Channel Memory Configurations
DDRII_1 DDRII_2 DDRII_3 DDRII_4
(Yellow Slot) (Orange Slot) (Yellow Slot) (Orange Slot) (1) Populated - Populated ­(2) - Populated - Populated (3)* Populated Populated Populated Populated
* For the configuration (3), please install identical DDRII DIMM s in all four slots.
English
EnglishEnglish
EnglishEnglish
1212
12
1212
1. If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in the slots of the same color. In other words, install them either in the set of yellow slots (DDRII_1 and DDRII_3), or in the set of orange slots (DDRII_2 and DDRII_4).
2. If only one memory module or three memory modules are installed in the DDRII DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory T e chnology.
3. If a pair of memory modules is NOT installed in the same Dual Channel, for exa mple, in stalling a pair of memory module s in D DRII_1 and DDRII_2, it is unable to activate the Dual Channel Memory Technology .
4. It is not allowed to install a DDR memory module into DDRII slot; otherwise, this motherboard and DIMM may be damaged.
5. If you plan to use ATITM PCI Express VGA card on this motherboard, the total system memory size should be above 512MB.
ASRock ConRoe1333-eSATA2 Motherboard
Installing a DIMMInstalling a DIMM
Installing a DIMM
Installing a DIMMInstalling a DIMM
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the bre a k
on the slot.
The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining cli ps at both ends fully
snap back in place and the DIMM is properly seated.
ASRock ConRoe1333-eSATA2 Motherboard
1313
13
1313
EnglishEnglish
EnglishEnglish
English
2.4 Expansion Slots (PCI, PCI Express, and AGI Express2.4 Expansion Slots (PCI, PCI Express, and AGI Express
2.4 Expansion Slots (PCI, PCI Express, and AGI Express
2.4 Expansion Slots (PCI, PCI Express, and AGI Express2.4 Expansion Slots (PCI, PCI Express, and AGI Express Slots) Slots)
Slots)
Slots) Slots)
There are 3 PCI slots, 2 PCI Express slots, and 1 AGI Express slot (PCI Express x4) on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane
width graphics cards. PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.
AGI Express slot (PCI Express x4):
AGI Express slot (PCI Express x4) is used to install PCI Express expan-
sion cards.
If you plan to install only one PCI Express card on this motherboard, please
install it on PCIE1 (PCIE x16 slot).
Installing an expansion cardInstalling an expansion card
Installing an expansion card
Installing an expansion cardInstalling an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Step 3. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 4. Fasten the card to the chassis with screws.
English
EnglishEnglish
EnglishEnglish
1414
14
1414
ASRock ConRoe1333-eSATA2 Motherboard
TMTM
TM
2.5 CrossFire2.5 CrossFire
2.5 CrossFire
2.5 CrossFire2.5 CrossFire
TMTM
Operation Guide Operation Guide
Operation Guide
Operation Guide Operation Guide
This motherboard supports CrossFireTM feature. CrossFireTM technology offers the most advantageous mea n s availa ble of combining multiple high perf ormance Gra phics Processing Units (GPU) in a single PC. Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism, CrossFireTM enables the highest possible level of performance and image quality in any 3D application. Currently CrossFireTM feature is supported with Windows® XP with Service Pack 2. Please check ATITM website for driver updates.
What graphics cards work with CrossFireTM?
A complete CrossFireTM system requires a CrossFireTM Ready motherboard, a CrossFireTM Edition graphics card and a compatible standard Radeon (CrossFire Ready) graphics card from the same series, or two CrossFireTM Ready cards if they are software enabled. This applies to cards from ATITM or any of its partners.
Cards For AGI Express Slot Cards For PCIE1 Slot
Radeon X1950Pro Series Radeon X1950Pro Series Radeon X1950XTX Series Radeon X1950XTX CrossFire Radeon X1950 Series Radeon X1950 CrossFireTM Edition Radeon X1900 Series Radeon X1900 CrossFireTM Edition Radeon X1800 Series Radeon X1800 CrossFireTM Edition Radeon X1650Pro Series Radeon X1650Pro Series Radeon X1600 Series Radeon X1600 Series Radeon X1300 Series Radeon X1300 Series Radeon X850 Series Radeon X850 CrossFireTM Edition
1. If a customer incorrectly configures their system they will not see the performance benefits of CrossFireTM. All three CrossFireTM components, a CrossFireTM Ready graphics card, a CrossFireTM Ready motherboard and a CrossFireTM Edition co-processor graphics card, must be installed correctly to benefit from the CrossFireTM multi-GPU platform.
2. If you pair a 12-pipe CrossFireTM Edition card with a 16-pipe card, both cards will operate as 12-pipe cards while in CrossFireTM mode.
TMTM
TM
Enjoy the benefit of CrossFireEnjoy the benefit of CrossFire
Enjoy the benefit of CrossFire
Enjoy the benefit of CrossFireEnjoy the benefit of CrossFire
Currently, A TITM has released Radeon X850XT , X1800XT, X1900XT , X1950XT, X1950Pro, X1950XTX, X1300, X1650 and X1600 CrossFireTM cards, which require different methods to enable CrossFire X850XT as the example graphics card. For other CrossFireTM cards that ATITM has released or will release in the future, please refer to ATITM graphics card manuals for detailed installation guide.
TM
TMTM
feature. In the below procedures, we use Radeon
TM
Edition
TM
Step 1. Connect to the system power supply. Please connect a hard disk power
connector to SLI/XFIRE Power connector on this motherboard.
It is recommended to use 500-Watt power supply or greater to perform the benefit of CrossFireTM feature for Radeon X850XT, X1900 and X1950 series.
EnglishEnglish
EnglishEnglish
English
ASRock ConRoe1333-eSATA2 Motherboard
1515
15
1515
Step 2. Install the standard Radeon (CrossFireTM Ready) graphics card to AGI Ex-
press slot (PCI Express x4). For the proper installation procedures, please refer to section “Expansion Slots”.
Standard Radeon (CrossFireTM Ready) graphics card
Step 3. Install the Radeon CrossFireTM Edition graphics card to PCIE1 slot. For the
proper installation procedures, please refer to section “Expansion Slots”.
English
EnglishEnglish
EnglishEnglish
1616
16
1616
Radeon CrossFire Edition graphics card
Standard Radeon (CrossFireTM Ready) graphics card
1. You are allowed to install two CrossFireTM Edition graphics cards to both slots, or you may use one CrossFire (CrossFireTM Ready) graphics card from the same series.
2. For A TITM Radeon X1300, X1600, X1650 and X1950Pro series, there are no CrossFire Edition graphics cards. You can still install two regular graphics cards from the same series on PCIE1 slot and AGI Express slot (PCI Express x4) to support CrossFireTM. Besides, please connect the monitor cable to the graphics card on PCIE1 slot.
TM
TM
Edition graphics cards a nd a compatible standard Radeon
Step 4. Correctly connect the DVI-DMS cable to the monitor connector and two
graphics cards that you install. (If you install two standard Radeon (CrossFireTM Ready) graphics cards to this motherboard, please skip this step.)
DVI-DMS cable DMS connector
Standard Radeon (CrossFireTM Ready) graphics card
DVI connector
D VI connector
Connect the DVI-DMS cable to DVI connector of the compatible standard Radeon (CrossFire Ready) graphics card.
TM
ASRock ConRoe1333-eSATA2 Motherboard
There are two DVI connectors on the standard Radeon (CrossFire graphics card. Please connect the DVI-DMS cable to the correct DVI connector; otherwise , the graphics card will not work.
TM
Ready)
TM
Radeon CrossFire Edition graphics card
TM
DMS connector
Connect the DVI-DMS cable to DMS connector of the CrossFire graphics card.
If you install two CrossFireTM Edition graphics cards to this motherboard, please connect one end of DVI-DMS cable to the monitor, another end to DMS of one of the CrossFireTM Edition graphics cards to PCIE1 slot, and the other end to DVI of another CrossFireTM Edition graphics card to AGI Express slot (PCI Express x4). If you install one CrossFireTM Edition graphics card and one compatible standard Radeon (CrossFireTM Ready) graphics card to this motherboard, please connect one end of DVI-DMS cable to the monitor, another end to DMS of the CrossFireTM Edition graphics card, a nd the other end to DVI of the compatible standard Radeon (CrossFireTM Ready) graphics card.
TM
Edition
Connect the DVI-DMS cable to the monitor connector.
Step 5. Power on your computer and boot into OS. Step 6. Remove the A TITM driver if you have any VGA driver installed in your system.
The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation. Please visit this website for the driver: http://support.ati.com/ics/support/DLRedirect.asp? fileIDExt=050553d40196ef109fff37cbb40aaf28&accountID=737&deptID=894
Step 7. Install the required drivers to your system. Please visit the websites below
for installing the drivers that ATITM recommends: A. ATITM recommends Windows® XP Service Pack 2 or higher to be installed (If you have Windows® XP Service Pack 2 or higher installed in your system, there is no need to download it again):
http://www.microsoft.com/windowsxp/sp2/default.mspx
B. You must have Microsoft .NET Framework installed prior to downloading and installing the CATALYST Control Center: http://www.microsoft.com/downloads/details.aspx? FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en
Step 8. Restart your computer.
EnglishEnglish
EnglishEnglish
English
ASRock ConRoe1333-eSATA2 Motherboard
1717
17
1717
Step 9. Install the VGA card drivers to your system, and restart your computer.
Then you will find “ATI Catalyst Control Center” on your desktop.
You will find “ATI Catalyst Control Center” on your desktop.
Step 10. Double-click “ATI Catalyst Control Center”. Click “View”, and select “Ad-
vanced View”. Click “CrossFireTM”, and then set the option “Enable CrossFireTM” to “Yes”.
View
English
EnglishEnglish
EnglishEnglish
1818
18
1818
CrossFire
TM
If you install one Radeon CrossFireTM Edition graphics card a nd one compatible standard Radeon (CrossFireTM Ready) graphics card to this motherboard but not two Radeon CrossFireTM Edition graphics cards, please as well follow the above steps. However, although you have selected the option “Enable CrossFireTM”, the CrossFireTM function can not work actually. Your computer will automatically reboot. After restarting your computer, please confirm whether the option “Enable CrossFireTM” in “ATI Catalyst Control Center” is selected or not; if not, please select it again, and then you are able to enjoy the benefit of CrossFire
TM
feature.
Enable CrossFire
Step 11. You can freely enjoy the benefit of CrossFireTM feature.
* CrossFireTM appearing here is a registered trademark of ATITM Technologies Inc., and is used
only for identification or explanation and to the owners’ benefit, without intent to infringe.
ASRock ConRoe1333-eSATA2 Motherboard
TM
2.6 Surround Display Feature2.6 Surround Display Feature
2.6 Surround Display Feature
2.6 Surround Display Feature2.6 Surround Display Feature
This motherboard supports Surround Display upgrade. With the external add-on PCI Express VGA card, you can easily enjoy the benefits of Surround Display feature. For the detailed instruction, please refer to the document at the following path in the Support CD:
..\ Surround Display Information
2.7 Jumpers Setup2.7 Jumpers Setup
2.7 Jumpers Setup
2.7 Jumpers Setup2.7 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper Setting Description
PS2_USB_PWR1 Short pin2, pin3 to enable
(see p.2 No. 1) +5VSB (standby) for PS/2
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
Clear CMOS
(CLRCMOS1, 2-pin jumper) (see p.2 No. 10)
2-pin jumper
Short Open
or USB wake up events.
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds.
2.8 Onboard Headers and Connectors2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
ASRock ConRoe1333-eSATA2 Motherboard
1919
19
1919
EnglishEnglish
EnglishEnglish
English
FDD connector
(33-pin FLOPPY1) (see p.2 No. 26)
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.2 No. 16)
English
EnglishEnglish
EnglishEnglish
2020
20
2020
connect the blue end
to the motherboard
connect the black end to the IDE devices
80-conductor ATA 66/100 cable
Note: Please refer to th e i n struction of your IDE device vendor for the details. Serial ATA II Connectors These four Serial ATA II
(SAT AII_BLUE (PORT0): (SATAII) connectors support see p.2, No. 19) SATA data cables for internal (SAT AII_BLACK (PORT1): storage devices. The current see p.2, No. 17) SATA II interface allows up to (SAT AII_RED (PORT2): 3.0 Gb/s data transfer rate. see p.2, No. 21)
(SAT AII_ORANGE (PORT3): see p.2, No. 15)
SATAII_RED (PORT2) and SATAII_ORANGE (PORT3) connectors can be used for internal storage devices or be connected to eSATAII_BOTTOM and eSA TAII_TOP connectors with corresponding color to support eSATAII devices. Please read “eSATAII Interface Introduction” on page 26 for details about eSATAII and eSATAII installation procedures.
SAT AII_ORANGE (PORT3)
SAT AII_RED (PORT2)
SAT AII_BLACK (PORT1)
SAT AII_BLUE (PORT0)
eSATA II Connectors These two eSATA II
(eSAT AII_TOP: see p.2, No. 37) connectors support SATA (eSAT AII_BOTTOM: see p.2, No. 36) data cables for external
SATAII function. The current
eSATAII_BOTTOM
eSATAII_TOP
eSATA II interface allows up to
3.0 Gb/s data transfer rate.
Serial A TA (SATA) Either end of the SATA data cable Data Cable can be connected to the SATA /
(Optional) SATAII hard disk or the SATAII
connector on the motherboard. You can also use the SATA data cable to connect SATAII connec­tors and eSATAII connectors with corresponding color.
ASRock ConRoe1333-eSATA2 Motherboard
Serial ATA (SATA) Please connect the black end of Power Cable SATA power cable to the power
(Optional) connector on each drive. Then
connect to the SAT A
HDD power connector
connect to the power supply
connect the white end of SATA power cable to the power connector of the power supply.
USB 2.0 Headers Besides two default USB 2.0
(9-pin USB67) ports on the I/O panel, there are (see p.2 No. 20) three USB 2.0 headers on this
motherboard. Each USB 2.0 header cansupport two USB
2.0 ports.
(9-pin USB45) (see p.2 No. 23)
(9-pin USB23) (see p.2 No. 24)
Infrared Module Header This header supports an
(5-pin IR1) optional wireless transmitting (see p.2 No. 1 1) and receiving infrared module.
Internal Audio Connectors This connector allows you
(4-pin CD1) to receive stereo audio input (CD1: see p.2 No. 28) from sound sources such as
CD1
a CD-ROM, D V D-ROM, TV tuner card, or MPEG card.
ASRock ConRoe1333-eSATA2 Motherboard
2121
21
2121
EnglishEnglish
EnglishEnglish
English
Front Panel Audio Header This is an interface for front
(9-pin HD_AUDIO1) panel audio cable that allows (see p.2 No. 29) convenient connection and
control of audio devices.
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel. E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from [Auto] to [Enabled]. F. Enter Windows system. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. Click “Audio I/O”, select “Connector Settings” , choose “Disable front panel jack
detection”, and save the change by clicking “OK”.
System Panel Header This header accommodates
(9-pin PANEL1) several system front panel (see p.2 No. 18) functions.
English
EnglishEnglish
EnglishEnglish
2222
22
2222
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1) speaker to this header. (see p.2 No. 14)
Chassis Fan Connector Please connect a chassis fan
(3-pin CHA_FAN1) cable to this connector and (see p.2 No. 12) match the black wire to the
ground pin.
CPU Fan Connector Please connect a CPU fan cable
(4-pin CPU_FAN1) to this connector and match (see p.2 No. 6) the black wire to the ground pin.
1 2 3 4
ASRock ConRoe1333-eSATA2 Motherboard
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Connector Please connect an ATX power
(20-pin ATXPW R1) supply to this connector. (see p.2 No. 35)
ATX 12V Connector Please connect an ATX 12V
(4-pin A TX12V1) power supply to this connector. (see p.2 No. 2)
SLI/XFIRE Power Connector It is not necessary to use this
(4-pin SLI/XFIRE_POWER1) connector, but please connect it (see p.2 No. 3) with a hard disk power connecor
when two graphics cards are
SLI/XFIRE_POWER1
plugged to this motherboard at the same ti me.
Game Port Hea der Connect a Game cable to this
(15-pin GAME1) header if the Game port bracket (see p.2 No. 27) is installed.
IEEE 1394 Headers There are two IEEE 1394
(9-pin FRONT_1394) headers on this motherboard, (see p.2 No. 25) including one front panel IEEE
1394 header (FRONT_1394) and one back pa nel IEEE 1394 header (BACK_1394). Each IEEE 1394 header cansupport one IEEE
(9-pin BACK_1394) 1394 port. (see p.2 No. 31)
ASRock ConRoe1333-eSATA2 Motherboard
2323
23
2323
EnglishEnglish
EnglishEnglish
English
HDMI_SPDIF Header HDMI_SPDIF header, providing
(3-pin HDMI_SPDIF1) SPDIF audio output to HDMI V GA (see p.2 No. 30) card, allows the system to
connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
English
EnglishEnglish
EnglishEnglish
HDMI_SPDIF Cable Please connect the black end (A)
(Optional) of HDMI_SPDIF cable to the
C
B
A
HDMI_SPDIF header on the motherboard. Then connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF connector of HDMI VGA card.
A. black end B. white end (2-pin) C. white end (3-pin)
USB+1394 Bracket This USB+1394 bracket can
support 2 additional USB 2.0 ports and 1 IEEE 1394 port. Please conne ct the blue conne c­tor on the cable of this USB+1394 bracket to the USB 2.0 header (USB23, USB45, or USB67), and connect the red connector on the cable of this USB+1394 bracket to the IEEE 1394 header (BACK_1394). Then fasten the USB+1394 bracket to the chassis with screws.
2424
24
2424
ASRock ConRoe1333-eSATA2 Motherboard
2.9 HDMI_SPDIF Header Connection Guide2.9 HDMI_SPDIF Header Connection Guide
2.9 HDMI_SPDIF Header Connection Guide
2.9 HDMI_SPDIF Header Connection Guide2.9 HDMI_SPDIF Header Connection Guide
HDMI (High-Definition Multi-media Interface) is an all-digital audio/video specification, which provides an interface between any compatible digital audio/video source, such as a set-top box, DVD player, A/V receiver and a compatible digital audio or video monitor, such as a digital television (DTV). A complete HDMI system require s a HDMI VGA card and a HDMI ready motherboard with a HDMI_SPDIF header. This motherboard is equipped with a HDMI_SPDIF header, which provides SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/projector/ LCD devices. To use HDMI function on this motherboard, please carefully follow the below steps.
• Step 1. Install the HDMI VGA card to the PCI Express Graphics slot on this
motherboard. For the proper installation of HDMI VGA card, please refer to the installation guide on page 14.
Step 2. Connect the black end (A) of HDMI_SPDIF cable to the
HDMI_SPDIF header (HDMI_SPDIF1, yellow , see page 2, No.
30) on the motherboard.
Make sure to correctly connect the HDMI_SPDIF cable to the motherboard and the HDMI VGA card according to the same pin definition. For the pin definition of HDMI_SPDIF header and HDMI_SPDIF cable conne ctors, ple ase refer to page 24. For the pin definition of HDMI_SPDIF connectors on HDMI VGA card, please refer to the user manual of HDMI VGA card vendor. Incorrect connection may cause permanent damage to this motherboard and the HDMI VGA card.
Step 3. Connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF
connector of HDMI VGA card. (There are two white ends (2-pin and 3-pin) on HDMI_SPDIF cable. Please choose the appropriate white end according to the HDMI_SPDIF connector of the HDMI V GA card you install.
white end (2-pin) (B)
Please do not connect the white end of HDMI_SPDIF cable to the wrong connector of HDMI VGA card or other VGA card. Otherwise, the motherboard and the VGA card may be damaged. For example, this picture shows the wrong example of connecting HDMI_SPDIF cable to the fan connector of PCI Express VGA card. Please refer to the VGA card user manual for connector usage in advance.
white end (3-pin) (C)
Step 4. Connect the HDMI output connector on HDMI VGA card to
HDMI device, such as HDTV. Please refer to the user manual of HDTV and HDMI VGA card vendor for detailed connection procedures.
Step 5. Install HDMI VGA card driver to your system.
ASRock ConRoe1333-eSATA2 Motherboard
2525
25
2525
EnglishEnglish
EnglishEnglish
English
2.10 eSA2.10 eSA
2.10 eSA
2.10 eSA2.10 eSA
What is eSATAII?
This motherboard supports eSATAII interface, the external SATAII specification. eSATAII allows you to enjoy the SATAII function provided by the I/O of your computer, offering the high speed data transfer rate up to 3.0Gb/s, and the convenient mobility like USB. eSATAII is equipped with Hot Plug ca pability that enables you to exchange drives easily. For example, with eSATAII interface, you may simply plug your eSATAII hard disk to the eSATAII ports instead of opening your chassis to exchange your SATAII hard disk. Currently, on the market, the data transfer rate of USB 2.0 is up to 480Mb/s, and for IEEE 1394 is up to 400Mb/ s. However, eSATAII provides the data transfer rate up to 3000Mb/s, which is much higher than USB 2.0 and IEEE 1394, and still keeps the convenience of Hot Plug feature. Therefore, on the basis of the advantageous transfer speed and the facilitating mobile capability, in the near future, eSATAII will replace USB 2.0 and IEEE 1394 to be a trend for external interface.
TT
AII InterAII Inter
T
AII Inter
TT
AII InterAII Inter
NOTE:
1. If you set “Configure SATA as” option in BIOS setup to AHCI or RAID mode, Hot Plug function is supported with eSATAII devices. Therefore, you can insert or remove your eSATAII devices to the eSATAII ports while the system is power-on and in working condition.
2. If you set “Configure SATA as” option in BIOS setup to IDE mode, Hot Plug function is not supported with eSATAII devices. If you still want to use eSATAII function in IDE mode, please insert or remove your eSATAII devices to the eSATAII ports only when the system is power-off.
3. Please refer to page 31 to 37 for detailed information of RAID mode, IDE mode, and AHCI mode.
face Introductionface Introduction
face Introduction
face Introductionface Introduction
English
EnglishEnglish
EnglishEnglish
2626
26
2626
How to install eSATAII?
SAT AII_ORANGE (POR T3) and SA TAII_RED (PORT2)
1. If you just plan to install one eSATAII device to this motherboard, it is recom­mended to enable the bottom eSATAII port of the I/O shield. In order to enable the bottom eSATAII port of the I/O shield, you need to connect the red SATAII connector (SATAII_RED (PORT2); see p.2 No.21) and the red eSATAII connector (eSATAII_BOTTOM; see p.2 No.36) with a SATA data cable first. Then the bottom eSATAII port of the I/O shield is enabled.
ASRock ConRoe1333-eSATA2 Motherboard
eSAT AII_T OP and eSATAII_BOTTOM
Connect the SATA data cable to the red SATAII connector (SATAII_RED (PORT2))
Connect the SATA data cable to the red eSATAII connector (eSATAII_BOTTOM)
2. If you plan to install two eSATAII devices to this motherboard, you need to enable both the top and the bottom eSATAII ports of the I/O shield. In order to enable the top and the bottom eSATAII ports of the I/O shield, you have to connect the red SATAII connector (SATAII_RED (PORT2); see p.2 No.21) and the red eSATAII connector (eSATAII_BOTTOM; see p.2 No.36) with a SATA data cable first, and then connect the orange SATAII connector (SATAII_ORANGE (PORT3); see p.2 No.15) and the orange eSATAII connec­tor (eSATAII_TOP; see p.2 No.37) with another SATA data cable. After that, both the top and the bottom eSATAII ports of the I/O shield are enabled.
Connect the SATA data cables to both red SATAII connector (SATAII_RED (PORT2)) and orange SATAII connector (SATAII_ ORANGE (PORT3))
Please make sure to correctly connect the SATAII and eSATAII connectors with corresponding color so that the eSATAII function will work successfully.
ASRock ConRoe1333-eSATA2 Motherboard
Connect the SATA data cables to both red eSATAII connector (eSATAII_BOTTOM) and orange eSATAII connector (eSAT AII_T OP)
2727
27
2727
EnglishEnglish
EnglishEnglish
English
3. Use the eSATAII device cable to connect eSATAII device and the eSATAII port of the I/O shield according to the eSATAII connector that you connect the SATA data cable.
Connect one end of the eSATAII device cable to eSATAII device
Comparison between eSATAII and other devices
IEEE 1394 400Mb/s USB 2.0 480Mb/s SATA 1.5Gb/s (1500Mb/s) eSATAII/SATAII 3.0Gb/s (3000Mb/s)
Connect the other end of the eSATAII device cable to eSATAII port of the I/O shield
English
EnglishEnglish
EnglishEnglish
2828
28
2828
ASRock ConRoe1333-eSATA2 Motherboard
2.11 SA2.11 SA
2.11 SA
2.11 SA2.11 SA
Before installing SATAII hard disk to your computer, please carefully read below SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be at SATAII mode, which operate with the best performance. In order to enable SATAII function, please follow the below instruction with different vendors to
correctly adjust your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard disk may fail to run at SATAII mode.
Western Digital
If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled. On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers from pin 5 and pin 6.
SAMSUNG
If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled. On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the jumpers from pin 3 and pin 4.
TT
AII Hard Disk Setup GuideAII Hard Disk Setup Guide
T
AII Hard Disk Setup Guide
TT
AII Hard Disk Setup GuideAII Hard Disk Setup Guide
HITACHI
Please use the Feature Tool, a DOS-bootable tool, for changing various ATA features. Please visit HITACHI’s website for details:
http://www.hitachigst.com/hdd/support/download.htm
The above examples are just for your reference. For different SATAII hard disk products of different vendors, the jumper pin setting methods may not be the same. Please visit the vendors’ website for the updates.
ASRock ConRoe1333-eSATA2 Motherboard
2929
29
2929
EnglishEnglish
EnglishEnglish
English
2.122.12
Serial ASerial A
2.12
Serial A
2.122.12
Serial ASerial A InstallationInstallation
Installation
InstallationInstallation
This motherboard adopts Intel® ICH7R south bridge chipset that supports Serial ATA (SATA) / Serial ATAII (SATAII) hard disks and RAID (RAID 0, RAID 1, RAID 10, RAID 5, and Intel Matrix Storage) functions. You may install SATA / SATAII hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA / SATAII hard disks.
STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk. STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
TT
A (SAA (SA
TT
A (SA
A (SAA (SA
A) / Serial AA) / Serial A
T
A) / Serial A
TT
A) / Serial AA) / Serial A
T
TT
1. If you plan to use RAID 0, RAID 1, or Intel Matrix Storage function, you need to install at least 2 SATA / SATAII hard disks. If you plan to use RAID 5 function, you need to install at least 3 SATA / SATAII hard disks. If you plan to use RAID 10 function, you need to install at least 4 SATA / SATAII hard disks. If you install 2 eSATAII devices, then only RAID 0, RAID 1, or Intel Matrix Storage functions will be enabled.
2. It is not recommended to switch the “Configure SATA as” setting between AHCI, RAID, and IDE mode after OS installation.
TT
AII (SAAII (SA
T
AII (SA
TT
AII (SAAII (SA
TT
AII) Hard DisksAII) Hard Disks
T
AII) Hard Disks
TT
AII) Hard DisksAII) Hard Disks
English
EnglishEnglish
EnglishEnglish
3030
30
3030
ASRock ConRoe1333-eSATA2 Motherboard
2.13 Hot Plug and Hot Swap F2.13 Hot Plug and Hot Swap F
2.13 Hot Plug and Hot Swap F
2.13 Hot Plug and Hot Swap F2.13 Hot Plug and Hot Swap F HDDs and eSAHDDs and eSA
HDDs and eSA
HDDs and eSAHDDs and eSA
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII / eSATAII Devices in RAID / AHCI mode. Intel® ICH7R south bridge chipset provides hardware support for Advanced Host controller Interface (AHCI), a new progra mming interface for SATA host controllers developed thru a joint industry effort. AHCI also provides usability enhancements such as Hot Plug.
NOTE What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is called “Hot Plug” for the action to insert and remove the SATA / SATAII HDDs while the system is still power-on and in working condition. However, please note that it cannot perform Hot Plug if the OS has been
installed into the SATA / SATAII HDD.
What is Hot Swap Function?
If SATA / SATAII HDDs are built as RAID1 then it is called “Hot Swap” for the action to insert and remove the SATA / SATAII HDDs while the system is still power-on and in working condition.
eSATAII is equipped with Hot Plug capability that enables you to exchange drives easily. For example, with eSATAII interface, you may simply plug your eSATAII devices to the eSATAII ports instead of opening your chassis to exchange your SATAII hard disk.
TT
AII DevicesAII Devices
T
AII Devices
TT
AII DevicesAII Devices
unctions for SAunctions for SA
unctions for SA
unctions for SAunctions for SA
TT
A / SAA / SA
T
A / SA
TT
A / SAA / SA
TT
T
TT
AIIAII
AII
AIIAII
2.142.14
Driver Installation Guide Driver Installation Guide
2.14
Driver Installation Guide
2.142.14
Driver Installation Guide Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.
2.152.15
Installing WindowsInstalling Windows
2.15
Installing Windows
2.152.15
Installing WindowsInstalling Windows
TMTM
TM
TMTM
VistaVista
Vista
VistaVista
If you want to install Windows® 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII HDDs with RAID functions, please follow below procedures according to the OS you install.
64-bit With RAID Functions 64-bit With RAID Functions
64-bit With RAID Functions
64-bit With RAID Functions 64-bit With RAID Functions
ASRock ConRoe1333-eSATA2 Motherboard
®
2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista
2000 / XP / XP 64-bit / Vista
2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista
TM TM
TM
TM TM
//
/
//
3131
31
3131
EnglishEnglish
EnglishEnglish
English
English
EnglishEnglish
EnglishEnglish
2.15.1 Installing Windows2.15.1 Installing Windows
2.15.1 Installing Windows
2.15.1 Installing Windows2.15.1 Installing Windows RAID Functions RAID Functions
RAID Functions
RAID Functions RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below steps.
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option “Configure SATA as”, please set the option to [RAID].
STEP 2: Make a SATA / SATAII Driver Diskette.
A. Insert the Support CD into your optical drive to boot your system. B. During POST at the beginning of system boot-up, press <F11> key, and then a window for boot devices selection appears. Please select CD-ROM as the boot device. C. When you see the message on the screen, “Do you want to generate Serial ATA driver diskette [YN]?”, press <Y>. D. Then you will see these messages,
Please insert a diskette into the floppy drive. WARNING! Formatting the floppy diskette will lose ALL data in it! Start to format and copy files [YN]?
Please insert a floppy diskette into the floppy drive, and press <Y>. E. The system will start to format the floppy diskette and copy SATA / SATAII drivers into the floppy diskette.
STEP 3: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure the RAID function, you need to check the installation guide in the Support CD for proper configuration. Please refer to the document in the Support CD, “Guide to SATA Hard Dis ks In stallation a nd RAID Configuration”, which is located in the folder at the following path: .. \ RAID Installation Guide
STEP 4: Install Windows® 2000 / XP / XP 64-bit OS on your system.
After making a SATA / SATAII driver diskette a nd using “RAID Installation Guide” to set RAID configuration, you can start to install Windows® 2000 / XP / XP 64-bit on your system. At the beginning of Windows setup, press F6 to install a third-party RAID driver. When prompted, insert the SATA / SATAII driver diskette containing the Intel RAID driver. After reading the floppy disk, the driver will be presented. Select the driver to install according to the mode you choose and the OS you install. You may select: “Intel(R) 82801GR/GH SATA RAID Controller (Des ktop ICH7R­Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH SATA RAID Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
®
2000 / XP / XP 64-bit With 2000 / XP / XP 64-bit With
2000 / XP / XP 64-bit With
2000 / XP / XP 64-bit With 2000 / XP / XP 64-bit With
®
3232
32
3232
ASRock ConRoe1333-eSATA2 Motherboard
®
After the installation of Windows to manage RAID functions, you are allowed to use both “RAID Installation Guide” and “Intel Matrix Storage Manager Information” for RAID configuration. Please refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which is located in the folder at the following path: .. \ RAID Installation Guide and the document in the support CD, “Guide to Intel Matrix Storage Manager”, which is located in the folder at the following path: .. \ Intel Matrix Storage Manager Information
If you want to use “Intel Matrix Storage Manager” in Windows® environment,
please install SATA / SATAII drivers from the Support CD again so that “Intel
Matrix Storage Manager” will be installed to your system as well.
2.15.2 Setting Up a “RAID Ready” System2.15.2 Setting Up a “RAID Ready” System
2.15.2 Setting Up a “RAID Ready” System
2.15.2 Setting Up a “RAID Ready” System2.15.2 Setting Up a “RAID Ready” System
2000 / Windows® XP / Windows® XP-64bit OS, if you want
You can also set up a “RAID Ready” system with a single SATA / SATAII hard disk. A “RAID Ready” system can be seamlessly upgraded to RAID 0, RAID 1 or RAID 5 at a later date by using RAID migration feature of Intel Matrix Storage. The following steps outline how to build an Intel “RAID Ready” system.
1. Assemble the system and attach a single SATA / SATAII hard drive.
2. Set up system BIOS as step 1 of page 32. When done, exit Setup.
3. Make a SATA / SATAII driver diskette as step 2 of page 32. Begin Windows
®
setup by booting from the installation CD.
4. At the beginning of Windows® setup, press F6 to install a third-party RAID driver. When prompted, insert the SATA / SATAII driver diskette containing the Intel® RAID driver. After reading the floppy disk, the driver will be presented. Select the driver to install according to the mode you choose and the OS you install. You may select: “Intel(R) 82801GR/GH SATA RAID Controller (Desktop ICH7R-Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH SATA RAID Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
5. Finish the Windows® installation and install all necessary drivers.
6. Install the Intel(R) Matrix Storage Manager software via the CD-ROM included with your motherboard or after downloading it from the Internet. This will add the Intel(R) Matrix Storage Console which can be used to manage the RAID configuration.
7. After setting up a “RAID Ready” system as the above steps, you can follow the procedures of the next section to migrate the system to RAID 0, RAID 1 or RAID
5.
EnglishEnglish
EnglishEnglish
English
ASRock ConRoe1333-eSATA2 Motherboard
3333
33
3333
2.15.3 Migrating a “RAID Ready” System to RAID 0,2.15.3 Migrating a “RAID Ready” System to RAID 0,
2.15.3 Migrating a “RAID Ready” System to RAID 0,
2.15.3 Migrating a “RAID Ready” System to RAID 0,2.15.3 Migrating a “RAID Ready” System to RAID 0,
RAID 1 or RAID 5 RAID 1 or RAID 5
RAID 1 or RAID 5
RAID 1 or RAID 5 RAID 1 or RAID 5
If you have an existing “RAID Ready” system, then you can use the following steps to perform a migration from a single non-RAID configuration to a two drive RAID 0, RAID 1 configuration or three drive RAID 5 configuration. To prepare for this, you will need another SATA / SATAII hard drive with a capacity equal to or greater than that currently being used as the source hard drive.
1. Physically attach one additional SATA / SATAII hard drive to the SATAII port not being used. Note the serial number of the hard drive already in the system; you will use this to select it as the source hard drive when initiating the migration.
2. Boot Windows®, install the Intel(R) Matrix Storage Manager software, if not already installed, using the setup package obtained from a CD-ROM or from the Internet. This will install the necessary Intel Storage Utility and start menu links.
3. Open the Intel Storage Utility from the Start Menu and select “Create RAID volume from Existing Hard Drive” from the Actions menu. This will activate the Create RAID volume from Existing Hard Drive Wizard. Click through the dialogs as prompted. It’s important to understand what will occur during the migration process because any data on the destination hard drive will be lost.
4. Once the migration is complete, reboot the system. If you migrated to a RAID 0 volume, use Disk Management from within Windows® in order to partition and format the empty space created when the two hard drive capacities are combined. You may also use third-party software to extend any existing partitions within the RAID volume.
English
EnglishEnglish
EnglishEnglish
3434
34
3434
Vista Vista
Vista
Vista Vista
TMTM
TM
TMTM
/ Vista / Vista
/ Vista
/ Vista / Vista
2.15.4 Installing Windows2.15.4 Installing Windows
2.15.4 Installing Windows
2.15.4 Installing Windows2.15.4 Installing Windows
RAID Functions RAID Functions
RAID Functions
RAID Functions RAID Functions
If you want to install Windows® VistaTM / VistaTM 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below steps.
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option “Configure SATA as”, please set the option to [RAID].
STEP 2: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure the RAID function, you need to check the installation guide in the Support CD for proper configuration. Please refer to the document in the Support CD, “Guide to SATA Hard Dis ks In stallation a nd RAID Configuration”, which is located in the folder at the following path: .. \ RAID Installation Guide
ASRock ConRoe1333-eSATA2 Motherboard
®
TMTM
TM
TMTM
64-bit With 64-bit With
64-bit With
64-bit With 64-bit With
STEP 3: Install Windows® VistaTM / VistaTM 64-bit OS on your system.
Insert the Windows® VistaTM / VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install Windows® VistaTM / VistaTM 64-bit OS on your system. When you see “Where do you want to install Windows?” page, please insert the ASRock Support CD into your optical drive, and click the “Load Driver” button on the left on the bottom to load the Intel® RAID drivers. Intel® RAID drivers are in the following path in our Support CD:
.. \ I386 \ Vista (For Windows® Vista .. \ AMD64 \ Vista64 (For Windows® Vista
After that, please insert Windows® VistaTM / VistaTM 64-bit optical disk into the optical drive again to continue the installation.
TM
OS)
TM
64-bit OS)
After the installation of Windows functions, you are allowed to use both “RAID Installation Guide” and “Intel Matrix Storage Manager Information” for RAID configuration. Please refer to the document in the Support CD, “Guide to SATA Hard D is ks Installation and RAID Configuration”, which is located in the folder at the following path: .. \ RAID Installation Guide and the document in the support CD, “Guide to Intel Matrix Storage Manager”, which is located in the folder at the following path: .. \ Intel Matrix Storage Manager Information
If you want to use “Intel Matrix Storage Manager” in Windows® environment,
please install SATA / SATAII drivers from the Support CD again so that “Intel
Matrix Storage Manager” will be installed to your system as well.
2.162.16
Installing WindowsInstalling Windows
2.16
Installing Windows
2.162.16
Installing WindowsInstalling Windows
TMTM
TM
TMTM
VistaVista
Vista
VistaVista
If you want to install Windows® 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below procedures according to the OS you install.
2.16.1 Installing Windows2.16.1 Installing Windows
2.16.1 Installing Windows
2.16.1 Installing Windows2.16.1 Installing Windows RAID Functions RAID Functions
RAID Functions
RAID Functions RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.
64-bit Without RAID Functions 64-bit Without RAID Functions
64-bit Without RAID Functions
64-bit Without RAID Functions 64-bit Without RAID Functions
The installation procedures for Windows® VistaTM / VistaTM 64-bit are subject to change. Please visit our website for the updates of Windows® Vista driver and related information in the future.
®
VistaTM / VistaTM 64-bit OS, if you want to manage RAID
®
2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista
2000 / XP / XP 64-bit / Vista
2000 / XP / XP 64-bit / Vista 2000 / XP / XP 64-bit / Vista
®
2000 / XP / XP 64-bit Without 2000 / XP / XP 64-bit Without
2000 / XP / XP 64-bit Without
2000 / XP / XP 64-bit Without 2000 / XP / XP 64-bit Without
TM TM
TM
TM TM
TM
/ VistaTM 64-bit
//
/
//
EnglishEnglish
EnglishEnglish
English
Using SATA / SATAII HDDs and eSATAII devices with NCQ and Hot Plug functions
ASRock ConRoe1333-eSATA2 Motherboard
3535
35
3535
STEP 1: Set Up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [AHCI].
STEP 2: Make a SATA / SATAII driver diskette.
Please make a SATA / SATAII driver diskette by following section 2.15.1 step 2 on page 32.
If you want to enable Hot Plug function on eSATAII ports but you install OS on IDE HDD, please skip step 2.
STEP 3: Install Windows® 2000 / XP / XP 64-bit OS on your system.
After making a SATA / SATAII driver diskette, you can start to install Windows® 2000 / XP / XP 64-bit on your system. At the beginning of Windows® setup, press F6 to install a third-party AHCI driver. When prompted, insert the SATA / SATAII driver diskette containing the Intel® AHCI driver. After reading the floppy disk, the driver will be presented. Select the driver to install according to the mode you choose and the OS you install. You may select: “Intel(R) 82801GR/GH SATA AHCI Controller (Des ktop ICH7R-Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH SATA AHCI Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
Using SATA / SATAII HDDs and eSATAII devices without NCQ and Hot Plug functions
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [IDE].
STEP 2: Install Windows® 2000 / XP / XP 64-bit OS on your system.
English
EnglishEnglish
EnglishEnglish
Vista Vista
Vista
Vista Vista
TM TM
TM
TM TM
/ Vista/ Vista
/ Vista
/ Vista/ Vista
2.16.2 Installing Windows2.16.2 Installing Windows
2.16.2 Installing Windows
2.16.2 Installing Windows2.16.2 Installing Windows RAID Functions RAID Functions
RAID Functions
RAID Functions RAID Functions
If you want to install Windows® VistaTM / VistaTM 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs and eSATAII devices with NCQ and Hot Plug functions
STEP 1: Set Up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [AHCI].
3636
36
3636
ASRock ConRoe1333-eSATA2 Motherboard
®
TMTM
TM
TMTM
64-bit Without 64-bit Without
64-bit Without
64-bit Without 64-bit Without
STEP 2: Install Windows® VistaTM / VistaTM 64-bit OS on your system.
After setting up BIOS, you can start to install Windows® VistaTM / VistaTM 64-bit on your system.
Using SATA / SATAII HDDs and eSATAII devices without NCQ and Hot Plug functions
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [IDE].
STEP 2: Install Windows® VistaTM / VistaTM 64-bit OS on your system.
After setting up BIOS, you can start to install Windows® VistaTM / VistaTM 64-bit on your system.
2.172.17
Untied Overclocking TUntied Overclocking T
2.17
Untied Overclocking T
2.172.17
Untied Overclocking TUntied Overclocking T
This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment.
echnologyechnology
echnology
echnologyechnology
Please refer to the warning on page 6 for the possible overclocking risk before you apply Untied Overclocking Technology.
ASRock ConRoe1333-eSATA2 Motherboard
3737
37
3737
EnglishEnglish
EnglishEnglish
English
3. BIOS Information3. BIOS Information
3. BIOS Information
3. BIOS Information3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.
English
EnglishEnglish
EnglishEnglish
4. Software Suppor4. Software Suppor
4. Software Suppor
4. Software Suppor4. Software Suppor
This motherboard supports various Microsoft® Windows® operating systems: 2000 / XP / XP 64-bit / VistaTM / Vista contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP. EXE” from the BIN folder in the Support CD to display the menus.
TM
64-bit. The Support CD that came with the motherboard
t CD informationt CD information
t CD information
t CD informationt CD information
3838
38
3838
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
3939
39
3939
®
® ® ®
® ®
®
®
®
4040
40
4040
ASRock ConRoe1333-eSATA2 Motherboard
®
®
ASRock ConRoe1333-eSATA2 Motherboard
4141
41
4141
4242
42
4242
®
®
®
®
ASRock ConRoe1333-eSATA2 Motherboard
®
® ®
®
®
® ®
®
®
®
ASRock ConRoe1333-eSATA2 Motherboard
4343
43
4343
4444
44
4444
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
4545
45
4545
4646
46
4646
ASRock ConRoe1333-eSATA2 Motherboard
DDRII_1 DDRII_2 DDRII_3 DDRII_4
( )( )( )( ) (1) - ­(2) - ­(3)
ASRock ConRoe1333-eSATA2 Motherboard
4747
47
4747
4848
48
4848
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
4949
49
4949
2.52.5
2.5
2.52.5
®
5050
50
5050
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
5151
51
5151
5252
52
5252
®
®
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
5353
53
5353
5454
54
5454
ASRock ConRoe1333-eSATA2 Motherboard
SAT AII_ORANGE (PORT3)
SAT AII_RED (PORT2)
SAT AII_BLACK (PORT1)
SAT AII_BLUE (PORT0)
eSATAII_BOTTOM
eSATAII_TOP
ASRock ConRoe1333-eSATA2 Motherboard
5555
55
5555
5656
56
5656
ASRock ConRoe1333-eSATA2 Motherboard
CD1
ASRock ConRoe1333-eSATA2 Motherboard
5757
57
5757
1 2 3 4
SLI/XFIRE_POWER1
5858
58
5858
ASRock ConRoe1333-eSATA2 Motherboard
C
B
A
ASRock ConRoe1333-eSATA2 Motherboard
5959
59
5959
6060
60
6060
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
6161
61
6161
6262
62
6262
ASRock ConRoe1333-eSATA2 Motherboard
IEEE 1394 400Mb/s USB 2.0 480Mb/s SATA 1.5Gb/s (1500Mb/s) eSATAII/SATAII 3.0Gb/s (3000Mb/s)
ASRock ConRoe1333-eSATA2 Motherboard
6363
63
6363
6464
64
6464
®
ASRock ConRoe1333-eSATA2 Motherboard
ASRock ConRoe1333-eSATA2 Motherboard
6565
65
6565
®
®
®
®
®
®
®
®
®
®
6666
66
6666
ASRock ConRoe1333-eSATA2 Motherboard
®
® ®
® ®
® ® ®
®
®
®
®
®
ASRock ConRoe1333-eSATA2 Motherboard
6767
67
6767
®
®
6868
68
6868
®
®
®
®
ASRock ConRoe1333-eSATA2 Motherboard
®
®
® ®
®
®
®
®
®
®
®
®
®
®
®
®
®
®
®
®
®
6969
69
6969
ASRock ConRoe1333-eSATA2 Motherboard
®
® ® ®
®
®
®
®
7070
70
7070
®
ASRock ConRoe1333-eSATA2 Motherboard
®
®
®
ASRock ConRoe1333-eSATA2 Motherboard
7171
71
7171
® ®
7272
72
7272
ASRock ConRoe1333-eSATA2 Motherboard
O:
X:
X O O O O O
X O O O O O
ASRock ConRoe1333-eSATA2 Motherboard
7373
73
7373
1. Einführung1. Einführung
1. Einführung
1. Einführung1. Einführung
Wir danken Ihnen für den Kauf des ASRock ConRoe1333-eSATA2 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robuste s Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.
Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com
1.1 Kartoninhalt
ASRock ConRoe1333-eSATA2 Motherboard
(ATX-Formfaktor: 30.5 cm x 21.8 cm; 12.0 Zoll x 8.6 Zoll) ASRock ConRoe1333-eSATA2 Schnellinstallationsanleitung ASRock ConRoe1333-eSATA2 Support-CD Ein 80-adriges Ultra-ATA 66/100 IDE-Flachbandkabel Ein Flachbandkabel für ein 3,5-Zoll-Diskettenlaufwerk Vier Serial ATA (SATA) -Datenkabel (optional) Zwei Serial ATA (SATA) -Festplattenstromkabel (optional) Ein HDMI_SPDIF-Kabel (Option) Ein ASRock 8CH_eSAT AII I/O Shield Ein USB+1394-Halterung
Deutsch
DeutschDeutsch
DeutschDeutsch
7474
74
7474
ASRock ConRoe1333-eSATA2 Motherboard
1.21.2
SpezifikationenSpezifikationen
1.2
Spezifikationen
1.21.2
SpezifikationenSpezifikationen
Plattform - ATX-Formfaktor: 30.5 cm x 21.8 cm; 12.0 Zoll x 8.6 Zoll CPU - LGA 775 für Intel® Dual Core CoreTM 2 Extreme- / CoreTM 2
Duo- / Pentium® D- / Pentium® Dual Core- / Pentium® 4- / Celeron®- / Celeron® D- Prozessoren
- Kompatibilität mit allen Zentraleinheiten (CPU) FSB1333/1066/ 800/533MHz außer Quadrangel Kerne (siehe VORSICHT 1)
- Unterstützt Hyper-Threading-Technologie (siehe VORSICHT 2)
- Unterstützt Untied-Übertaktungstechnologie (siehe VORSICHT 3)
- Unterstützt EM64T -CPU
Chipsatz - Northbridge: Intel® 945P/945G
- Southbridge: Intel® ICH7R
Speicher - Unterstützung von Dual-Kanal-DDRII-Speichertechnologie
(siehe VORSICHT 4)
- 4 x Steckplätze für DDRII
- Unterstützt DDRII667/533 (siehe VORSICHT 5)
- Max. 4GB (siehe VORSICHT 6)
Hybrid Booster - Schrittloser CPU-Frequenz-Kontrolle (siehe VORSICHT 7)
- ASRock U-COP (siehe VORSICHT 8)
- Boot Failure Guard (B.F.G. – Systemstartfehlerschutz) Erweiterungs- - Unterstützt ATITM CrossFire steckplätze - 3 x PCI -Steckplätze
- 1 x PCI Express x16-Steckplätze
- 1 x AGI Express (PCI Express x4)-Steckplätze
- 1 x PCI Express x1-Steckplätze Audio - 7.1 CH Windows® VistaTM Premium Level HD Audio
(ALC888 Audio Codec)
LAN - PCIE x1 Giga bit LAN 10/100/1000 Mb/s
- Realtek RTL8111B
- Unterstützt Wake-On-LAN E/A-Anschlüsse ASRock 8CH_eSA TAII I/O an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss
- 1 x Serieller port: COM 1
- 1 x Paralleler port: Unterstützung für ECP / EPP
- 2 x Standard-USB 2.0-Anschlüsse
- 2 x eSATAII Ports
- 1 x RJ-45 Port
TM
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock ConRoe1333-eSATA2 Motherboard
7575
75
7575
Deutsch
DeutschDeutsch
DeutschDeutsch
7676
76
7676
- HD Audiobuchse: Lautsprecher seitlich / Lautsprecher hinten / Mitte/Bass / Audioeingang/ Lautsprecher vorne / Mikrofon (siehe VORSICHT 9)
Gratis-Paket: USB- und 1394-Blech, bietet 2 zusätzliche USB 2.0-Ports und 1 IEEE 1394-Port
Anschlüsse - 4 x Serial ATAII 3,0 GB/s-Anschlüsse, unterstützen RAID-
(RAID 0, RAID 1, RAID 10, RAID 5 und Intel Matrix Storage), NCQ, AHCI und “Hot Plug” Funktionen (siehe VORSICHT 10)
- 2 x eSATAII 3.0 GB/s-Anschlüsse (mit 2 SATAII-Anschlüssen geteilt), unterstützt „Hot Plug“-Funktion (siehe VORSICHT 11)
- 1 x ATA100 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)
- 1 x FDD-Anschlüsse
- 1 x Infrarot-Modul-Header
- 1 x Game-Anschluss
- 1 x HDMI_SPDIF-Anschluss
- 2 x IEEE 1394-Anschlussleisten
- CPU/Gehäuse-Lüfteranschluss
- 20-pin ATX-Netz-Header
- 4-pin anschluss für 12V-ATX-Netzteil
- SLI/XFIRE-Netz-Header
- Interne Audio-Anschlüsse
- Anschluss für Audio auf der Gehäusevorderseite
- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher USB 2.0-Anschlüsse) (siehe VORSICHT 12)
BIOS - 4Mb AMI BIOS
- AMI legal BIOS mit Unterstützung für “Plug and Play”
- ACPI 1.1-Weckfunktionen
- JumperFree-Modus
- SMBIOS 2.3.1
Support-CD - Treiber, Dienstprogramme, Antivirussoftware
(Probeversion)
Hardware Monitor - Überwachung der CPU-Temperatur
- Motherboardtemperaturerkennung
- Drehzahlmessung für CPU-Lüfter
- Drehzahlmessung für Gehäuselüfter
- CPU-Lüftergeräuschdämpfung
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
Betriebssysteme - Unterstützt Microsoft® Windows® 2000 / XP / XP 64-Bit /
VistaTM / Vista
Zertifizierungen - FCC, CE, WHQL
ASRock ConRoe1333-eSATA2 Motherboard
TM
64-Bit (siehe VORSICHT 13)
WARNUNG
Beachten Sie bitte, dass Overclocking, einschließlich der Einstellung im BIOS, Anwenden der Untied Overclocking-Technologie oder Verwenden von Overclocking-Werkzeugen von Dritten, mit einem gewissen Risiko behaftet ist. Overclocking kann sich nachteilig auf die Stabilität Ihres Systems auswirken oder sogar Komponenten und Geräte Ihres Systems beschädigen. Es geschieht dann auf eigene Gefahr und auf Ihre Kosten. Wir übernehmen keine Verantwortung für mögliche Schäden, die aufgrund von Overclocking verursacht wurden.
VORSICHT!
1. FSB1333-CPU wird nach Uhrzeitmode operatieren. In diese Situation wird PCIE Frequenz auch nach Uhrzeitmode zu 115MHz.
2. Die Einstellung der “Hyper-Threading Technology”, finden Sie auf Seite 48 des auf der Support-CD enthaltenen Benutzerhandbuches beschrieben.
3. Dieses Motherboard unterstützt die Untied-Übertaktungstechnologie. Unter “Entkoppelte Übertaktungstechnologie” auf Seite 111 finden Sie detaillierte Informationen.
4. Dieses Motherboard unterstützt Dual-Kanal-Speichertechnologie. Vor Implementierung der Dual-Kanal-Speichertechnologie müssen Sie die Installationsanleitung für die Speichermodule auf Seite 83 zwecks richtiger Installation gelesen haben.
5. Die unterstützten Arbeitsspeicherfrequenzen und die entsprechende CPU FSB-Frequenz entnehmen Sie bitte der nachstehenden Tabelle.
CPU FSB-Frequenz Unterstützte Arbeitsspeicherfrequenz
1333 DDRII533*, DDRII667 1066 DDRII533, DDRII667 800 DDRII400, DDRII533, DDRII667 533 DDRII400, DDRII533
* Bei Verwendung einer FSB1333-CPU auf diesem Motherboard läuft es
mit DDRII500, wenn Sie ein DDRII533-Speichermodul verwenden.
6. Aufgrund von Chipset-Einschränkungen könnte unter Windows Windows® XP, Windows® XP 64-Bit, Windows® VistaTM und Windows® Vista 64-Bit die für das System reservierte Speichergröße unterhalb von 4 GB liegen.
7. Obwohl dieses Motherboard stufenlose Steuerung bietet, wird Over­clocking nicht empfohlen. Frequenzen, die über den für den jeweiligen Prozessor vorgesehenen liegen, können das System instabil werden lassen oder die CPU beschädigen.
8. Wird eine Überhitzung der CPU registriert, führt das System einen automatischen Shutdown durch. Bevor Sie das System neu starten, prüfen Sie bitte, ob der CPU-Lüfter am Motherboard richtig funktioniert, und stecken Sie bitte den Stromkabelstecker aus und dann wieder ein. Um die Wärmeableitung zu verbessern, bitte nicht vergessen, etwa s Wärmeleitpa ste zwischen CPU und Kühlkörper zu sprühen.
®
2000,
TM
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock ConRoe1333-eSATA2 Motherboard
7777
77
7777
9. For microphone input, this motherboard supports both stereo and mono
modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.
10. Bevor Sie eine SATA II Festplatte mit dem SATA II Anschluss verbinden,
lesen Sie bitte die “Anleitung zur SATA II Festplatteneinrichtung“ auf Seite 102, um Ihre SATA II Festplatte in den SATA II Modus umzuschalten. SATA-Festplatten können Sie auch direkt mit dem SATA II-Anschluss verbinden.
11. Dieses Motherboard unterstützt die eSATAII-Schnittstelle, externe
SATAII-Spezifikation. Bitte lesen Sie den Abschnitt „Vorstellung der eSATAII-Schnittstelle“ auf Seite 98. Dort finden Sie detaillierte Informationen über eSATAII und zur eSATAII-Installation.
12. Das Power Management für USB 2.0 arbeitet unter Microsoft® Windows
VistaTM 64-Bit / VistaTM / XP 64-Bit / XP SP1 oder SP2/2000 SP4 einwandfrei.
13. Der Microsoft® Windows® VistaTM / VistaTM 64-Bit Treiber wird ständig
aktualisiert. Sobald wir den neuesten Treiber haben, stellen wir ihn auf unserer Website zur Verfügung. Bitte besuchen Sie unsere Website für den Microsoft® Windows® VistaTM / VistaTM 64-Bit Treiber und verwandte Informationen. ASRock-Website http://www.asrock.com
®
Deutsch
DeutschDeutsch
DeutschDeutsch
7878
78
7878
1.31.3
Minimale Hardwarevorausetzungen für WindowsMinimale Hardwarevorausetzungen für Windows
1.3
Minimale Hardwarevorausetzungen für Windows
1.31.3
Minimale Hardwarevorausetzungen für WindowsMinimale Hardwarevorausetzungen für Windows
TMTM
TM
TMTM
VistaVista
Vista
VistaVista
Premium 2007 und Basic Logo Premium 2007 und Basic Logo
Premium 2007 und Basic Logo
Premium 2007 und Basic Logo Premium 2007 und Basic Logo
Systemintegratoren und Anwender unseres Motherboards, die ihre Rechner auf die Vergabe des Windows® VistaTM Premium 2007 und Basic­ Logos vorbereiten möchten, finden die minimalen hardwarevoraussetzungen in der folgenden Tabelle.
CPU Celeron D 326 Speicher 1 GB Systemspeicher (Premium)
512 MB, Single Channel (Basic)
VGA DX9.0 mit WDDM-Treiber
mit 128 Bit-VGA-Speicher (Pre mium) mit 64 Bit-VGA-Speicher (Basic)
* Nach dem ersten Juni, 2007 sind , all Windows® VistaTM Systems dafür erforderlich, mit der Minimalforderung der obengenannte Hardware übereinzustimmen, um Windows® VistaTM Premium 2007 logo.zu befähigen.
ASRock ConRoe1333-eSATA2 Motherboard
®
2. Installation2. Installation
2. Installation
2. Installation2. Installation
Sicherheitshinweise vor der MontageSicherheitshinweise vor der Montage
Sicherheitshinweise vor der Montage
Sicherheitshinweise vor der MontageSicherheitshinweise vor der Montage
Bitte nehmen Sie die folgende Sicherheitshinweise zur Kenntnis, bevor Sie das Motherboard einbauen oder Veränderungen an den Einstellungen vornehmen.
1. Trennen Sie das System vom Stromnetz, bevor Sie eine ystemkomponente berühren, da es sonst zu schweren Schäden a m Motherboard oder den sonstigen internen, bzw. externen omponenten kommen kann.
2. Um Schäden aufgrund von statischer Elektrizität zu vermeiden, das Motherboard NIEMALS auf einen Teppich o.ä.legen. Denken Sie außerem daran, immer ein geerdetes Armband zu tragen oder ein geerdetes Objekt aus Metall zu berühren, bevor Sie mit Systemkomponenten hantieren.
3. Halten Sie Komponenten immer an den Rändern und vermeiden Sie Berührungen mit den ICs.
4. Wenn Sie Komponenten ausbauen, legen Sie sie immer auf eine antistatische Unterlage, oder zurück in die Tüte, mit der die Komponente geliefert wurde.
5. Wenn Sie da s Motherboard mit den Schrauben an dem Computergehäuse befestigen, überziehen Sie bitte die Schrauben nicht! Das Motherboard kann sonst beschädigt werden.
2.1 CPU Installation2.1 CPU Installation
2.1 CPU Installation
2.1 CPU Installation2.1 CPU Installation
Für die Installation des Intel 775-Pin CPU führen Sie bitte die folgenden Schritte durch.
(Ladeplatte)
(Kontaktreihe)
(Sockel)
775-Pin Sockel Übersicht
Bevor Sie die 775-Pin CPU in den Sockel sitzen, prüfen Sie bitte, ob die CPU-Oberfläche sauber ist und keine der Kontakte verbogen sind. Setzen Sie die CPU nicht mit Gewalt in den Sockel, dies kann die CPU schwer beschädigen.
ASRock ConRoe1333-eSATA2 Motherboard
7979
79
7979
DeutschDeutsch
DeutschDeutsch
Deutsch
Schritt 1. Öffnen Sie den Sockel:
Schritt 1-1. Öffnen Sie den Hebel, indem
Sie ihn nach unten drücken und aushaken.
Schritt 1-2. Drehen Sie den Ladehebel, bis
er in geöffneter Position steht, ca. 135 Grad.
Schritt 1-3. Drehen Sie die Ladeplatte, bis
sie in geöffneter Position steht, ca. 100 Grad.
Schritt 2. 775-Pin CPU einstecken:
Schritt 2-1. Halten Sie die CPU an den mit
schwarzen Linien gekennzeichneten Seiten.
Schritt 2-2. Halten Sie das Teil mit dem IHS
(Integrated Heat Sink – integrierter Kühlkörper) nach oben. Suchen Sie Pin 1 und die zwei Orientierungseinkerbungen.
Pin1
Orientierungskerbe
Ausrichtungsmarkierung
Orientierungskerbe
Pin1
Schwarze Linie
775-Pin Sockel
Schwarze Linie
Ausrichtungsmarkierung
Deutsch
DeutschDeutsch
DeutschDeutsch
8080
80
8080
775-Pin CPU
Um die CPU ordnungsgemäß einsetzen zu können, richten Sie die zwei Orientierungskerben der CPU mit den beiden Markierungen des Sockels aus.
Schritt 2-3. Drücken Sie die CPU vorsichtig
in vertikaler Richtung in den Sockel.
ASRock ConRoe1333-eSATA2 Motherboard
Schritt 2-4. Prüfen Sie, dass die CPU
ordnungsgemäß im Sockel sitzt und die Orientierungskerben einwandfrei in den entsprechenden Auskerbungen sitzen.
Schritt 3. PnP-Kappe entfernen (Pick and Place-Kappe):
Halten Sie den Rand der Ladeplatte mit Zeigefinger und Daumen Ihrer linken Hand, halten Sie die PnP-Kappe mit dem Daumen der rechten Hand und ziehen Sie die Kappe vom Sockel während Sie auf die Mitte der Kappe drücken, um ein Entfernen zu erleichtern.
1. Verwenden Sie beim Entfernen die Kappenlasche und vermeiden Sie ein Abreißen der PnP-Kappe.
2. Diese Kappe muss angebracht werden, falls Sie das Motherboard zur Reparatur bringen.
Schritt 4. Sockel schließen:
Schritt 4-1. Drehen Sie die Ladeplatte auf
den Kühlkörper (IHS).
Schritt 4-2. Drücken Sie leicht auf die
Ladeplatte und schließen Sie den Ladehebel.
Schritt 4-3. Sichern Sie Ladehebel und
Ladeplatte mithilfe des Hebelverschlusses.
ASRock ConRoe1333-eSATA2 Motherboard
8181
81
8181
DeutschDeutsch
DeutschDeutsch
Deutsch
2.22.2
Installation des CPU-Lüfters und KühlkörpersInstallation des CPU-Lüfters und Kühlkörpers
2.2
Installation des CPU-Lüfters und Kühlkörpers
2.22.2
Installation des CPU-Lüfters und KühlkörpersInstallation des CPU-Lüfters und Kühlkörpers
Für Installationshinweise, siehe Betriebsanleitung Ihres CPU-Lüfters und Kühlkörpers. Unten stehend ein Beispiel zur Installation eines Kühlkörpers für den 775-Pin CPU.
Schritt 1. Geben Sie Wärmeleitmaterial auf die Mitte
des IHS, auf die Sockeloberfläche.
Schritt 2. Setzen Sie den Kühlkörper auf den Sockel.
Prüfen Sie, dass die Lüfterkabel auf der Seite am nächsten zum CPU-Lüfter­Anschluss des Motherboards verlaufen (CPU_FAN1, siehe Seite 2, Nr. 6).
Schritt 3. Richten Sie Verbindungselemente und
Löcher im Motherboard aus.
Schritt 4. Drehen Sie die Verbindungselemente im
Uhrzeigersinn und drücken Sie mit dem Daumen auf die Kappen der Elemente zum Feststellen. Wiederholen Sie dies mit den anderen Verbindungselementen.
Wenn Sie die Verbindungselemente nur drücken, ohne sie im Uhrzeigersinn zu drehen, wird der Kühlkörper nicht ordnungsgemäß am Motherboard befestigt.
(Tragen Sie Wärmeleitmaterial auf. )
(Lüfterkabel auf der Seite am nächsten zum Anschluss des Motherboards)
(Schlitze der Verbindungselemente nach außen)
(Nach unten drücken (4 Stellen))
Deutsch
DeutschDeutsch
DeutschDeutsch
8282
82
8282
Schritt 5. Schließen Sie den Lüfter an den CPU-
Lüfteranschluss des Motherboards.
Schritt 6. Befestigen Sie überschüssiges Kabel mit
Band, um eine Störung des Lüfters oder Kontakt mit anderen Teilen zu vermeiden.
ASRock ConRoe1333-eSATA2 Motherboard
2.3 Installation der Speichermodule (DIMM)2.3 Installation der Speichermodule (DIMM)
2.3 Installation der Speichermodule (DIMM)
2.3 Installation der Speichermodule (DIMM)2.3 Installation der Speichermodule (DIMM)
Die Motherboards ConRoe1333-eSATA2 bieten vier 240-pol. DDRII (Double Data Rate II) DIMM-Steckplätze und unterstützen die Dual-Kanal-Speichertechnologie. Für die Dual-Kanalkonfiguration dürfen Sie nur identische (gleiche Marke, Geschwindigkeit, Größe und gleicher Chiptyp) DDRII DIMM-Paare in den Steckplätzen gleicher Farbe installieren. Mit anderen Worten, sie müssen ein identisches DDR DIMM-Paar im Dual-Kanal A (DDRII_1 und DDRII_3; gelbe Steckplätze, siehe Seite 2 Nr. 7) oder ein identisches DDRII DIMM-Paar im Dual­Kanal B (DDRII_2 und DDRII_4; orange Steckplätze, siehe Seite 2 Nr. 8) installieren, damit die Dual-Kanal-Speichertechnologie aktiviert werden kann. Auf diesem Motherboard können Sie auch vier DDRII DIMMs für eine Dual-Kanal konf iguration installieren. Auf diesem Motherboard können Sie auch vier DDRII DIMM-Module für eine Dual-Kanalkonfiguration installieren, wobei Sie bitte in allen vier Steckplätzen identische DDRII DIMM-Module installieren. Beziehen Sie sich dabei auf die nachstehende Konfigurationstabelle für Dual-Kanalspeicher.
Dual-Kanal-Speicherkonfigurationen
DDRII_1 DDRII_2 DDRII_3 DD RII_4
(gelbe Steckplätze) (orange Steckplätze) (gelbe Steckplätze) (orange Steckplätze)
(1) Bestückt - Bestückt ­(2) - Bestückt - Bestückt (3) Bestückt Bestückt Bestückt Bestückt
* Für Konfiguration (3) installieren Sie bitte identische DDRII DIMMs in allen vier
• Steckplätzen.
1. Wenn Sie zwei Speichermodule installieren möchten, verwenden Sie dazu für optimale Kompatibilität und Stabilität Steckplätze gleicher Farbe. Installieren Sie die beiden Speichermodule also entweder in den gelbe Steckplätzen (DDRII_1 und DDRII_3) oder den orange Steckplätzen (DDRII_2 und DDRII_4).
2. Wenn nur ein Speichermodul oder drei Speichermodule in den DDRII DIMM-Steckplätzen auf diesem Motherboard installiert sind, kann es die Dual-Kanal-Speichertechnologie nicht aktivieren.
3. Ist ein Speichermodulpaar NICHT im gleichen “Dual-Kanal” installiert, z.B. ein Speichermodulpaar wird in DDRII_1 und DDRII_2 installiert, kann es die Dual-Kanal-Speichertechnologie nicht aktivieren.
4. Es ist nicht zulässig, DDR in einen DDRII Steckplatz zu installieren; andernfalls könnten Motherboard und DIMMs beschädigt werden.
5. Wenn Sie eine PCI Express-VGA-Karte von ATI Motherboard verwenden möchten, muss der Haupspeicher (System­RAM) mehr als 512 MB groß sein.
TM
mit diesem
ASRock ConRoe1333-eSATA2 Motherboard
8383
83
8383
DeutschDeutsch
DeutschDeutsch
Deutsch
Einsetzen eines DIMM-ModulsEinsetzen eines DIMM-Moduls
Einsetzen eines DIMM-Moduls
Einsetzen eines DIMM-ModulsEinsetzen eines DIMM-Moduls
Achten Sie darauf, das Netzteil abzustecken, bevor Sie DIMMs oder Systemkomponenten hinzufügen oder entfernen.
Schritt 1: Öffnen Sie einen DIMM-Slot, indem Sie die seitlichen Clips nach außen
drücken.
Schritt 2: Richten Sie das DIMM-Modul so über dem Slot aus, dass das Modul mit
der Kerbe in den Slot passt.
Die DIMM-Module passen nur richtig herum eingelegt in die Steckplätze. Falls Sie versuchen, die DIMM-Module mit Gewalt falsch herum in die Steckplätze zu zwingen, führt dies zu dauerhaften Schäden am Mainboard und am DIMM-Modul.
Deutsch
DeutschDeutsch
DeutschDeutsch
8484
84
8484
Schritt 3: Drücken Sie die DIMM-Module fest in die Steckplätze, so dass die
Halteklammern an beiden Enden des Moduls einschnappen und das DIMM-Modul fest an Ort und Stelle sitzt.
ASRock ConRoe1333-eSATA2 Motherboard
2.4 Erweiterungssteckplätze: (PCI- , PCI Express-und AGI2.4 Erweiterungssteckplätze: (PCI- , PCI Express-und AGI
2.4 Erweiterungssteckplätze: (PCI- , PCI Express-und AGI
2.4 Erweiterungssteckplätze: (PCI- , PCI Express-und AGI2.4 Erweiterungssteckplätze: (PCI- , PCI Express-und AGI Express-Slots): Express-Slots):
Express-Slots):
Express-Slots): Express-Slots):
Es stehen 3 PCI- , 2 PCI Express - und 1 AGI Express -Slot (PCI Express x4) auf dem ConRoe1333-eSATA2 Motherboard zur Verfügung. PCI-Slots: PCI-Slots werden zur Installation von Erweiterungskarten mit dem 32bit PCI-Interface genutzt. PCI Express-Slots: PCIE1 (PCIE x16-Steckplatz) wird für PCI Express-
Grafikkarten mit x16-Busbreite verwendet. PCIE2 (PCIE x1-Steckplatz) wird für PCI Express­ Grafikkarten mit x1-Busbreite verwendet wie Gigabit LAN­ Karten, SATA2-Karten, usw. eingesetzt.
AGI Express-Slot: AGI Express Steckplatz (PCI Express x4) ist für den
Anschluss von PCI Express-Erweiterungskarten.
Wenn Sie nur eine PCI Express-Karte in diesem Motherboard installieren möchten, installieren Sie diese bitte im PCIE1-Steckplatz (PCIE x16­Steckplatz).
Einbau einer ErweiterungskarteEinbau einer Erweiterungskarte
Einbau einer Erweiterungskarte
Einbau einer ErweiterungskarteEinbau einer Erweiterungskarte
Schritt 1: Bevor Sie die Erweiterungskarte installieren, vergewissern Sie sich,
dass das Netzteil ausgeschaltet und das Netzkabel abgezogen ist. Bitte lesen Sie die Dokumentation zur Erweiterungskarte und nehmen Sie nötige Hardware-Einstellungen für die Karte vor, ehe Sie mit der Installation beginnen.
Schritt 2: Entfernen Sie das Abdeckungsblech (Slotblende) von dem
Gehäuseschacht (Slot) , den Sie nutzen möchten und behalten die Schraube für den Einbau der Karte.
Schritt 3: Richten Sie die Karte über dem Slot aus und drücken Sie sie ohne
Gewalt hinein, bis sie den Steckplatz korrekt ausfüllt.
Schritt 4: Befestigen Sie die Karte mit der Schraube aus Schritt 2.
ASRock ConRoe1333-eSATA2 Motherboard
8585
85
8585
DeutschDeutsch
DeutschDeutsch
Deutsch
TMTM
TM
2.52.5
2.5
2.52.5
CrossFireCrossFire
CrossFire
CrossFireCrossFire
TMTM
Bedienungsanleitung Bedienungsanleitung
Bedienungsanleitung
Bedienungsanleitung Bedienungsanleitung
Dieses Motherboard unterstützt die CrossFireTM-Funktion. Die CrossFireTM­Technologie bietet die nützlichsten Vorteile beim Zusammenschließen mehrerer leistungsstarken GPUs (Graphics Processing Units) in einem PC an. Durch das Kombinieren verschiedener Betriebsmodi, das intelligente Software-Design sowie einen innovativen Zusammenschaltmechanismus ermöglicht CrossFireTM das maximal mögliche Leistungsniveau und die maximale Bildqualität in allen 3D­Applikationen. Zur Zeit wird die CrossFireTM-Funktion nur von Windows® XP mit Service Pack 2 unterstützt. Informieren Sie sich auf der ATITM-Website nach Treiber-Updates.
Welche Grafikkarten funktionieren mit CrossFireTM?
Ein rundum CrossFireTM-kompatibles System erfordert ein CrossFireTM Ready­ Motherboard, eine CrossFireTM Edition-Grafikkarte und eine kompatible Radeon­ Standardgrafikkarte (CrossFireTM Ready) derselben Serie, oder zwei CrossFire Ready-Karte, sofern diese durch Software aktiviert werden. Dies gilt für ATITM­ Karten und Karten von ATITM-Partnern.
Karten für AGI Express-Steckplatz Karten für PCIE1-Steckplatz Radeon X1950Pro-Serie Radeon X1950Pro-Serie Radeon X1950XTX-Serie Radeon X1950XTX CrossFireTM Edition Radeon X1950-Serie Radeon X1950 CrossFireTM Edition Radeon X1900-Serie Radeon X1900 CrossFireTM Edition Radeon X1800-Serie Radeon X1800 CrossFireTM Edition Radeon X1650Pro-Serie Radeon X1650Pro-Serie Radeon X1600-Serie Radeon X1600-Serie Radeon X1300-Serie Radeon X1300-Serie Radeon X850-Serie Radeon X850 CrossFireTM Edition
TM
Deutsch
DeutschDeutsch
DeutschDeutsch
8686
86
8686
1. Wenn IHr System nicht richtig konfiguriert ist, konnen Sie die Leistungsvorteile von CrossFire Ready Grafikkarte, ein CrossFireTM Ready Motherboard und eine CrossFire Edition Co-Prozessor-Grafikkarte, müssen richtig installiert werden, um Nutzen aus der CrossFireTM Multi-GPU-Plattform zu ziehen.
2. Wenn eine 12-Pipe CrossFireTM Edition Karte mit einer 16-Pipe-Karte zusammen verwendet wird, arbeiten die beiden Karten nur mit 12 Pipelines im CrossFireTM­ Modus.
Den VDen V
Den V
Den VDen V
oror
teil der CrossFteil der CrossF
or
teil der CrossF
oror
teil der CrossFteil der CrossF
ATITM bietet derzeit Grafikk arten der Serie Ra deon X850XT, X1800XT, X1900XT, X1950XT, X1950Pro, X1950XTX, X1300, X1650 und X1600 CrossFireTM an, bei denen die CrossFireTM-Funktionen jeweils unterschiedlich aktiviert werden. Bei den folgenden Schritten benutzen wir eine Radeon X850XT zur Verdeutlichung. Bei anderen CrossFireTM-Karten aus der aktuellen oder zukünftigen Produktpalette von ATITM lesen Sie zur Installation bitte in den jeweiligen Bedienungsanleitungen zur Grafikkarte nach.
TM
nicht erleben. Alle drei CrossFire
TMTM
TM
TMTM
ireire
genießen genießen
ire
genießen
ireire
genießen genießen
TM
Komponenten, eine CrossFire
ASRock ConRoe1333-eSATA2 Motherboard
TM
TM
Schritt 1. Nehmen Sie die Stromversorgungsverbindung vor. Verbinden Sie
bitte einen Festplattenstromsteckverbinder mit dem SLI/XFIRE Power­Anschluss.
Wir empfehlen Ihnen ein Netzteil mit 500 Watt oder noch höherer Leistung zu verwenden, um die CrossFireTM-
Funktion zu nutzen für Radeon X850XT, X1900 und X1950-serie.
Schritt 2. Stecken Sie die normale Radeon (CrossFireTM Ready) Grafikkarte in
den AGI Express-Steckplatz (PCI Express x4) ein. Für Hinweise zur Installation sehen Sie bitte im Abschnitt “Erweiterungssteckplätze” nach.
Normale Radeon (CrossFireTM Ready) Grafikkarte
Schritt 3. Stecken Sie die Radeon CrossFireTM Edition Grafikkarte in den PCIE1-
Steckplatz ein. Für Hinweise zur Installation sehen Sie bitte im Abschnitt “Erweiterungssteckplätze” nach.
Radeon CrossFire Edition Grafikkarte
Normale Radeon (CrossFireTM Ready) Grafikkarte
1. Sie können entweder zwei CrossFire Steckplätze einstecken oder eine CrossFireTM Edition Grafikkarte und eine kompatible normale Radeon (CrossFireTM Ready) Grafikkarte von der selben Serie verwenden.
2. Für die ATITM Radeon X1300, X1600, X1650 und X1950Pro-Serien gibt es keine CrossFire können Sie weiterhin zwei normale Grafikkarten aus derselben Serie im PCIE1- und im AGI Express (PCI Express x4)-Steckplatz installieren. Verbinden Sie auch das Monitorkabel mit der Grafikkarte im PCIE1­ Steckplatz.
TM
TM
Edition Grafikkarten in die beiden
TM
Edition-Grafikkarten. Zur Unterstützung von CrossFire
Schritt 4. Verbinden Sie das DVI-DMS-Kabel mit den zwei installierten
Grafikkarten und dem Anschluss am Monitor. (Wenn Sie zwei Radeon-Standardgrafikkarten (CrossFire TM Ready) in diesem Motherboard installieren, überspringen Sie bitte diesen Schritt.)
ASRock ConRoe1333-eSATA2 Motherboard
TM
DeutschDeutsch
DeutschDeutsch
Deutsch
8787
87
8787
DMS-AnschlussDVI-DMS-Kabel
Normale Radeon (CrossFireTM Ready) Grafikkarte
DVI-Anschluss
D VI-Anschluss
Deutsch
DeutschDeutsch
DeutschDeutsch
Verbinden Sie das DVI-DMS
-Kabel mit dem DVI­Anschluss an der kompatiblen normalen Radeon (CrossFire Ready) Grafikkarte.
Radeon CrossFire Edition Grafikkarte
Wenn Sie zwei CrossFire ein Ende des DVI-DMS-Kabels mit dem Anschluss am Monitor, ein anderes Ende mit dem DMS-Anschluss an der CrossFireTM Edition Grafikkarte, die im PCIE1-Steckplatz sitzt, und das andere Ende mit dem DVI­Anschluss an der CrossFireTM Edition Grafikkarte, die im AGI Express­Steckplatz (PCI Express x4) sitzt. Wenn Sie eine CrossFireTM Edition Grafikkarte und eine kompatible normale Radeon (CrossFireTM Ready) Grafikkarte installieren, verbinden Sie bitte ein Ende des DVI-DMS-Kabels mit dem DVI-Anschluss am Monitor, ein anderes Ende mit dem DMS-Anschluss an der CrossFireTM Edition Grafikkarte und das andere Ende mit dem Anschluss an der Radeon (CrossFireTM Ready) Grafikkarte.
Es gibt zwei DVI-Anschlüsse an der normalen Radeon (CrossFireTM Ready) Grafikkarte.
TM
TM
Bitte verbinden Sie das DVI-DMS-Kabel mit dem richtigen DVI-Anschluss. Andernfalls kann die Grafikkarte nicht funktionieren.
DMS­Ansc­hluss
Verbinden Sie das DVI-DMS­Kabel mit dem DMS-Anschluss an der CrossFire Grafikkarte.
TM
Edition
TM
Edition Grafikkarten installieren, verbinden Sie bitte
Verbinden Sie da s DVI-DMS­Kabel mit dem Anschluss am Monitor.
Schritt 5. Schalten Sie den Computer ein und fahren das Betriebssystem hoch. Schritt 6. Entfernen Sie jeden früher installierten ATITM-VGA-Treiber von Ihrem
System.
8888
88
8888
ASRock ConRoe1333-eSATA2 Motherboard
Hierzu ist der Catalyst Uninstaller hilfreich. Wir empfehlen Ihnen, dieses Dienstprogramm zu verwenden, um alle früher installierten Catalyst-Treiber zu deinstallieren. Bitte besuchen Sie die folgende Website, um das Dienstprogramm herunterzuladen: http://support.ati.com/ics/support/DLRedirect.asp? fileIDExt=050553d40196ef109fff37cbb40aaf28&accountID=737&deptID=894
Schritt 7. Installieren Sie die notwendigen Treiber für Ihr System. Bitte
besuchen Sie die folgenden Websites für die Treiber, die ATI
TM
empfiehlt: A. ATI empfiehlt die Installation des Windows® XP service Pack 2 order
dessen Nachfolger (Wenn Windows® XP Service Pack 2 oder dessen Nachfolger bereits in lhrem System installiert ist, dann mussen Sie es nicht emeut downloaden):
http://www.microsoft.com/windowsxp/sp2/default.mspx
B. Vor dem Downloaden und Installieren des CATALYST Control
Center muss Microsoft .NET Framework installiert werden: http://www.microsoft.com/downloads/details.aspx? FamilyId=262D25E3-F589-4842-8157-
034D1E7CF3A3&displaylang=en Schritt 8. Starten Sie den Computer neu. Schritt 9. Installieren Sie die VGA-Kartentreiber und starten dann den Computer
neu. “ATI Catalyst Control Center” wird auf Ihrem Desktop angezeigt.
“ATI Catalyst Control Center” wird auf Ihrem Desktop angezeigt.
Schritt 10. Klicken Sie doppelt auf “ATI Catalyst Control Center”. Klicken Sie auf
“View” (Ansicht) und wählen dann “Advanced View” (Erweiterte Ansicht). Klicken Sie auf “CrossFireTM” und haken dann die Option “Enable CrossFireTM” (CrossFireTM aktivieren) an.
ASRock ConRoe1333-eSATA2 Motherboard
8989
89
8989
DeutschDeutsch
DeutschDeutsch
Deutsch
View (Ansicht)
CrossFire
TM
Enable CrossFire (CrossFire
Befolgen Sie bitte auch die obigen Schritte, wenn Sie statt zwei Radeon CrossFireTM Edition Grafikkarten eine Radeon CrossFireTM Edition Grafikkarte und eine normale kompatible Radeon (CrossFireTM Ready) installieren. Dennoch kann die CrossFireTM-Funktion nicht wirklich in Kraft treten, nachdem Sie die Option “Enable CrossFireTM” angehakt haben. Der Computer wird automatisch neu gestartet. Überprüfen Sie nach dem Neustarten des Computers, ob die Option “Enable CrossFireTM” (CrossFireTM aktivieren) angehakt ist. Wenn nicht, haken Sie sie bitte erneut an. Dann können Sie die Vorzüge der CrossFireTM­Funktion genießen.
Schritt 11. Jetzt können Sie den Nutzen aus der CrossFireTM-Funktion ziehen.
* CrossFireTM ist ein eingetragenes Warenzeichen der ATITM Technologies Inc. und wird nur zur
Identifizierung oder Erläuterung und zu Gunsten des Inhabers, ohne Rechtverletzungsabsicht, verwendet.
2.6 “Surround Display”2.6 “Surround Display”
2.6 “Surround Display”
2.6 “Surround Display”2.6 “Surround Display”
Dieses Motherboard unterstützt Surround Display-Aufrüstung. Mit zusätzlichen PCI Express-VGA-Karte können Sie die Vorteile der Surround Display-Funktion problemlos genießen. Für detaillierte Informationen, siehe folgendes Dokument auf beiliegender Support-CD: ..\ Surround Display Information
TM
TM
aktivieren)
Deutsch
DeutschDeutsch
DeutschDeutsch
9090
90
9090
2.7 Einstellung der Jumper2.7 Einstellung der Jumper
2.7 Einstellung der Jumper
2.7 Einstellung der Jumper2.7 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Gebrückt” sind, bzw. es befindet sich eine Jumper­Kappe auf diesen beiden Pins.
ASRock ConRoe1333-eSATA2 Motherboard
Gebrückt Offen
Jumper Einstellun Beschreibung
PS2_USB_PWR1 Überbrücken Sie Pin2, Pin3, um
(siehe S.2 - No. 1) +5VSB (Standby) zu setzen
und die PS/2 oder USB­Weckfunktionen zu aktivieren.
Hinweis: Um +5VSB nutzen zu können, muss das Netzteil auf dieser Leitung 2A
oder mehr leisten können.
CMOS löschen
(CLRCMOS1, 2-Pin jumper) (siehe S.2 - No. 10)
2-Pin jumper
Hinweis: CLRCMOS1 erlaubt Ihnen das Löschen der CMOS-Daten. Diese
beinhalten das System-Passwort, Datum, Zeit und die verschiedenen BIOS-Parameter. Um die Systemparameter zu löschen und auf die Werkseinstellung zurückzusetzen, schalten Sie bitte den Computer ab und entfernen das Stromkabel. Benutzen Sie eine Jumperkappe, um die Pins an CLRCMOS1 für 5 Sekunden kurzzuschließen.
2.8 Integrierte Header und Anschlüsse2.8 Integrierte Header und Anschlüsse
2.8 Integrierte Header und Anschlüsse
2.8 Integrierte Header und Anschlüsse2.8 Integrierte Header und Anschlüsse
Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf diese He ader und Anschlüsse. Wenn Sie Jumperkappen auf Header und Anschlüsse setzen, wird das Motherboard unreparierbar beschädigt!
Anschluss für das Floppy-Laufwerk
(33-Pin FLOPPY1) (siehe S.2 - No. 26)
die rotgestreifte Seite auf Stift 1
Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Kabel mit der Stift 1-
Seite des Anschlusses verbunden wird.
Primärer IDE-Anschluss (blau)
(39-pin IDE1, siehe S.2 - No. 16)
Blauer Anschluss Schwarzer Anschluss zum Motherboard zur Festplatte
80-adriges ATA 66/100 Kabel
Hinweis: Details entnehmen Sie bitte den Anweisungen Ihres IDE-Gerätehändlers.
ASRock ConRoe1333-eSATA2 Motherboard
9191
91
9191
DeutschDeutsch
DeutschDeutsch
Deutsch
Seriell-ATAII-Anschlüsse Diese vier Serial A TAII-
(SAT AII_BLUE (PORT0): (SATAII-)Verbínder unterstützten siehe S.2 - No. 19) SATA-Datenkabel für interne (SAT AII_BLACK (PORT1): Massen speichergeräte. Die siehe S.2 - No. 1 1) aktuelle SATAII-Schnittstelle (SAT AII_RED (PORT2): ermöglicht eine siehe S.2 - No. 21) Datenübertragungsrate bis (SAT AII_ORANGE (PORT3): 3,0 Gb/s.
siehe S.2 - No. 15)
Die Anschlüsse SATAII_RED (PORT2) (rot) und SATAII_ORANGE (PORT3) (orange) können für interne Speichergeräte verwendet oder zur Unterstützung von eSATAII-Geräten mit den Anschlüssen eSA TAII_BOTTOM und eSATAII_TOP in den entsprechenden Farben verbunden werden. Bitte lesen Sie den Abschnitt „Vorstellung der eSATAII-Schnittstelle“ auf Seite 98. Dort finden Sie detaillierte Informationen über eSA TAII und zur eSATAII-Installation.
SAT AII_ORANGE (PORT3)
SAT AII_RED (PORT2)
SAT AII_BLACK (PORT1)
SAT AII_BLUE (PORT0)
Deutsch
DeutschDeutsch
DeutschDeutsch
eSATAII-Anschlüsse
(eSAT AII_TOP: siehe S.2 - No. 37) (eSAT AII_BOTTOM: siehe S.2 - No. 36)
An diese beiden eSATAII­Anschlüsse können Sie SATA­Datenkabel für externe SATAII­Funktionen anschließen. Die derzeitige eSATAII-Schnittstelle
eSATAII_BOTTOM
eSATAII_TOP
ermöglicht Datentransferraten von bis zu 3,0 GB/s.
Serial A TA- (SATA-) Sie können beide Enden des Datenkabel SATA-Datenkabels entweder
(Option) mit der SATA / SATAII-
Festplatte oder dem SATAII-Anschluss am Mainboard verbinden.
Serial A TA- (SA TA-) Verbinden Sie bitte das Stromversorgungskabel schwarze Ende des SATA-
(Option) Stromversorgungskabels mit
SATA-HDD-Stromanschluss
Verbindung zum
Verbindung zum Netzteil
dem Stromanschluss jedes Laufwerks. Verbinden Sie dann das weiße Ende des SATA-Stromversorgungskabels mit dem Stromanschluss des Netzteils.
9292
92
9292
ASRock ConRoe1333-eSATA2 Motherboard
USB 2.0-Header Zusätzlich zu den zwei
(9-pol. USB67) üblichen USB 2.0-Ports an den (siehe S.2 - No. 20) I/O-Anschlüssen befinden sich
drei USB 2.0-Anschlussleisten am Motherboard. Pro USB 2.0­ Anschlussleiste werden zwei USB 2.0-Ports unterstützt.
(9-pol. USB45) (siehe S.2 - No. 23)
(9-pol. USB23) (siehe S.2 - No. 24) .
Infrarot-Modul-Header Dieser Header unterstützt ein
(5-pin IR1) optionales, drahtloses Sende- (siehe S.2 - No. 1 1) und Empfangs-Infrarotmodul.
n
Interne Audio-Anschlüsse Diese ermöglichen Ihnen
(4-Pin CD1) Stereo-Signalquellen, wie z. B. (CD1: siehe S.2 - No. 28) CD-ROM, DV D-ROM, TV-Tuner
CD1
oder MPEG-Karten mit Ihrem System zu verbinden.
Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorderseite
(9-Pin HD_AUDIO1) Ihres Gehäuses, ermöglicht (siehe S.2 - No. 29) Ihnen eine bequeme
Anschlussmöglichkeit und Kontrolle über Audio-Geräte.
1. High Definition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am
Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie
bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an.
ASRock ConRoe1333-eSATA2 Motherboard
9393
93
9393
DeutschDeutsch
DeutschDeutsch
Deutsch
B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an. D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden. E. Rufen Sie das BIOS-Setup-Dienstprogramm auf. Wechseln Sie zu Erweiterte Einstellungen und wählen Sie Chipset-Konfiguration. Setzen Sie die Option Frontleistenkontrolle von [Automatisch] auf [Aktiviert]. F. Rufen Sie das Windows-System auf. Klicken Sie auf das Symbol in der Taskleiste unten rechts, um den Realtek HD Audio-Manager aufzurufen. Klicken Sie auf “Audio-E/A”, wählen Sie die “Anschlusseinstellungen”
, wählen Sie “Erkennung der Frontleistenbuchse deaktivieren”
und speichern Sie die Änderung durch Klicken auf “OK”.
System Panel-Header Dieser Header unterstützt
(9-pin PANEL1) mehrere Funktion der (siehe S.2 - No. 18) Systemvorderseite.
Gehäuselautsprecher-Header Schließen Sie den
(4-pin SPEAKER1) Gehäuselautsprecher an (siehe S.2 - No. 14) diesen Header an.
Deutsch
DeutschDeutsch
DeutschDeutsch
9494
94
9494
Gehäuselüfteranschluss Verbinden Sie das
(3-pin CHA_FAN1) Gehäuselüfterkabel mit diesem (siehe S.2 - No. 12) Anschluss und passen Sie den
schwarzen Draht dem Erdungsstift an.
CPU-Lüfteranschluss Verbinden Sie das CPU -
(4-pin CPU_FAN1) Lüfterkabel mit diesem (siehe S.2 - No. 6) Anschluss und passen Sie den
1 2 3 4
schwarzen Draht dem Erdungsstift an.
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss (Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den Pins 1 – 3.
Lüfter mit dreipoligem Anschluss installieren
Pins 1–3 anschließen
ASRock ConRoe1333-eSATA2 Motherboard
ATX-Netz-Header Verbinden Sie die ATX-
(20-pin A TXPWR1) Stromversorgung mit diesem (siehe S.2 - No. 35) Header.
ATX 12V Anschluss Bitte schließen Sie an diesen
(4-pin A TX12V1) Anschluss die ATX 12V (siehe S.2 - No. 2) Stromversorgung an.
SLI/XFIRE-Stromanschluss
(4-pin SLI/XFIRE_POWER1) (siehe S.2 - No. 3)
Sie müssen diesen Anschluss nicht zwingend verwenden. Wenn allerdings zwei Grafikkarten gleichzeitig am
SLI/XFIRE_POWER1
Motherboard angeschlossen sind, verbinden Sie diesen Anschluss bitte mit einem Festplatten-Stromversorgungs­stecker.
Game-Anschluss Verbinden Sie ein Game-Kabel
(15-pin GAME1) mit diesem Anschluss, wenn (siehe S.2 - No. 27) der Game-Anschlusshalter
installiert ist.
IEEE 1394-Anschlussleisten Auf dem Motherboard befinden
(9-pin FRONT_1394) sich zwei IEEE 1394- (siehe S.2 - No. 25) Anschlussleisten; eine IEEE
1394-Frontanschlussleiste (FRONT_1394) und eine rückwärtige IEEE 1394­Anschlussleiste (BACK_1394).
(9-pin BACK_1394) Jeder IEEE 1394- (siehe S.2 - No. 31) Anschlussleiste unterstützt
einen IEEE 1394-Port.
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock ConRoe1333-eSATA2 Motherboard
9595
95
9595
HDMI_SPDIF-Anschluss Der HDMI_SPDIF-Anschluss
(HDMI_SPDIF1, dreipolig) stellt einen SPDIF- (siehe S.2 - No. 30) Audioausgang für eine HDMI-
VGA-Karte zur Verfügung und ermöglicht den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten, Projektoren, LCD-Geräten an das System. Bitte verbinden Sie den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte mit die sem Anschluss.
HDMI_SPDIF-Kabel Bitte verbinden Sie das
(Option) schwarze Ende (A) des
C
B
A
HDMI_SPDIF-Kabels mit dem HDMI_SPDIF-Anschluss am Motherboard. Schließen Sie dann das weiße Ende (B oder C) des HDMI_SPDIF-Kabels an den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte an.
A. Schwarzes Ende B. Weißes Ende (zweipolig) C. Weißes Ende (dreipolig)
Deutsch
DeutschDeutsch
DeutschDeutsch
9696
96
9696
USB+1394-Halterung Da s USB+1394-Blech
unterstützt zwei zusätzliche USB 2.0-Ports und einen IEEE 1394-Port. Bitte verbinden Sie den blauen Stecker des Kabels
zum USB+1394-Blech mit der
USB 2.0-Anschlussleiste (USB23, USB45 oder USB67), den roten Stecker des Kabels zum USB+1394-Blech mit der IEEE 1394-Anschlussleiste (BACK_1394). Fixieren Sie das USB+1394-Blech danach mit Schrauben am Gehäuse.
ASRock ConRoe1333-eSATA2 Motherboard
2.92.9
HDMI_SPDIF-Anschluss – InstallationshinweiseHDMI_SPDIF-Anschluss – Installationshinweise
2.9
HDMI_SPDIF-Anschluss – Installationshinweise
2.92.9
HDMI_SPDIF-Anschluss – InstallationshinweiseHDMI_SPDIF-Anschluss – Installationshinweise
HDMI (Hochauflösende Multimedia-Schnittstelle) ist eine komplett digitale Audio/ Video-Spezifikation, die eine Schnittstelle zwischen sämtlichen kompatiblen Digitalaudio-/Videoquellen zur Verfügung stellt. Beispiele für solche Digitalgeräte sind Digitalempfänger , D VD-Player, A/V-Receiver sowie kompatible Audiosysteme und Videoanzeigegeräte zum digitalen Fernsehen (DTV). Ein komplettes HDMI­System benötigt eine HDMI-VGA-Karte und ein HDMI-kompatibles Motherboard mit verbundenem HDMI_SPDIF-Anschluss. Ihr Motherboard ist mit einem HDMI_SPDIF­Anschluss ausgestattet, der einen SPDIF-Audioausgang für eine HDMI-VGA-Karte zur Verfügung stellt und den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten/Projektoren/LCD-Geräten an das System ermöglicht. Um die HDMI­Funktionen Ihres Motherboards nutzen zu können, führen Sie bitte die nachstehenden Schritte aus.
Schritt 1: Installieren Sie die HDMI-V GA-Karte im PCI Express-Steckplatz Ihres
Motherboards. Hinweise zur Installation der HDMI-VGA-Karte finden Sie in der Installationsanleitung auf Seite 85.
Schritt 2: Verbinden Sie das schwarze Ende (A) des HDMI_SPDIF-
Kabels mit dem HDMI_SPDIF-Anschluss (HDMI_SPDIF1, gelb, siehe Seite 2, Nr. 30) am Motherboard.
Achten Sie darauf, dass das HDMI_SPDIF-Kabel richtig an Motherboard und HDMI­VGA-Karte a nge schlossen wird; be achten Sie die jeweilige Pinbelegung. Hinweise zur Pinbelegung des HDMI_SPDIF-Anschlusses sowie der Stecker am HDMI_SPDIF-Kabel finden Sie auf Seite 96. Die Pinbelegung des HDMI_SPDIF-Anschlusses finden Sie in der Dokumentation Ihrer HDMI-VGA-Karte. Anschlussfehler können Motherboard und HDMI-VGA-Karte irrepara bel beschädigen.
Schritt 3: Schließen Sie das w eiße Ende (B oder C) des HDMI_SPDIF-Kabels an
den HDMI_SPDIF-Anschluss der HDMI-V GA-Karte a n. Am HDMI_SPDIF­Kabel befinden sich zwei weiße Enden (zwei- und dreipolig). Bitte wählen Sie das zum HDMI_SPDIF-Anschluss Ihrer VGA-Karte passende weiße Ende aus.
Weiße s Ende (zweipolig) (B)
Schließen Sie das weiße Ende des HDMI_SPDIF-Kabels keinesfalls an den falschen Anschluss der HDMI-VGA-Karte oder gar an eine andere VGA-Karte an. Dadurch können Motherboard und VGA-Karte schwer beschädigt werden. In der Abbildung sehen Sie ein Beispiel für einen falschen Anschluss: Hier wird versucht, das HDMI_SPDIF-Kabel mit dem Lüfteranschluss der PCI Express-VGA-Karte zu verbinden. Schauen Sie in die Dokumentation Ihrer VGA-Karte und informieren Sie sich schon im Vorfeld über die richtige Nutzung der Anschlüsse.
ASRock ConRoe1333-eSATA2 Motherboard
Weiße s Ende (dreipolig) (C)
9797
97
9797
DeutschDeutsch
DeutschDeutsch
Deutsch
Schritt 4: Schließen Sie den HDMI-Ausgang an ein HDMI-Gerät an; z. B.
an ein HDTV-Gerät. Hinweise zum richtigen Anschluss finden Sie in der Dokumentation des HDMI-Gerätes und der VGA-Karte.
Schritt 5: Installieren Sie die HDMI-V GA-Kartentre iber in Ihrem System.
Deutsch
DeutschDeutsch
DeutschDeutsch
2.10 V2.10 V
2.10 V
2.10 V2.10 V
Was ist eSATAII ?
Dieses Motherboard unterstützt die eSATAII-Schnittstelle, externe SATAII­Spezifikation. eSATAII ermöglicht die Nutzung von SATAII-Funktionen, die von den Ein-/Ausgabeschnittstellen Ihres Computers zur Verfügung gestellt werden, dabei stehen Ihnen schnelle Datentransferraten von bis zu 3,0 GB/s bei einer ähnlich guten Mobilität wie bei USB-Verbindungen zur Verfügung. eSATAII ist „Hot Plug“­fähig - das bedeutet, dass Sie Laufwerke ganz einfach austauschen können. Beispielsweise können Sie eine eSATAII-Festplatte durch die eSATAII-Schnittstelle einfach mit den eSATAII-Anschlüssen verbinden, statt das Gehäuse zum Austausch öffnen zu müssen. Derzeit beträgt die maximale Datentransferrate von USB 2.0 bis zu 480 MB/s, die von IEEE 1394 bis zu 400 MB/s. eSATAII dagegen bietet eine Datentransferrate von bis zu 3000 MB/s, also erheblich mehr als USB
2.0 und IEEE 1394 - und ist durch die „Hot Plug“-Funktionalität genauso komfortabel. Aus diesem Grund werden USB 2.0 und IEEE 1394 als externe Schnittstellen in naher Zukunft vermutlich durch eSATAII abgelöst, da eSATAII höhere Transferraten bei identisch komfortabler Handhabung bietet.
orstellung der eSAorstellung der eSA
orstellung der eSA
orstellung der eSAorstellung der eSA
HINWEIS:
1. Wenn Sie die Option “Configure SATA as” im BIOS-Setup auf den AHCI- oder den RAID-Modus setzen, wird die Hot Plug-Funktion auf eSATAII-Geräten unterstützt. Daher können Sie Ihre eSATAII-Geräte bei eingeschaltetem und in Betrieb befindlichem System mit den eSATAII-Anschlüssen verbinden oder von ihnen abtrennen.
2. Wenn Sie die Option “Configure SATA as” im BIOS-Setup auf den IDE-Modus setzen, wird die Hot Plug-Funktion auf eSATAII-Geräten nicht unterstützt. Möchten Sie die eSATAII-Funktion dennoch im IDE-Modus verwenden, verbinden Sie Ihre eSATAII-Geräte nur dann mit den eSATAII-Anschlüssen, oder trennen Sie diese nur dann davon ab, wenn das System ausgeschaltet ist.
3. Detaillierte Informationen über den RAID-Modus, den IDE-Modus und den AHCI-Modus sind auf den Seiten 104 zu 110 angegeben.
TT
AII-SchnittstelleAII-Schnittstelle
T
AII-Schnittstelle
TT
AII-SchnittstelleAII-Schnittstelle
9898
98
9898
ASRock ConRoe1333-eSATA2 Motherboard
Wie installieren Sie eSATAII ?
SAT AII_ORANGE (POR T3) und SATAII_RED (PORT2)
eSAT AII_T OP und eSATAII_BOTTOM
1. Wenn Sie nur ein eSATAII-Gerät an Ihr Motherboard anschließen möchten, sollten Sie den unteren eSATA-Anschluss am Ein-/Ausgabefeld verwenden. Zum Aktivieren des unteren eSATAII-Anschlusses des Ein-/ Ausgabefeldes müssen Sie zunächst den roten SATAII-Anschluss (SATAII_RED (PORT2); siehe Se ite 2, Nr. 21) und den roten eSATAII­Anschluss (eSATAII_BOTTOM; siehe Seite 2, Nr. 36) mit einem SATA­Datenkabel verbinden. Danach ist der untere eSATAII-Anschluss am Ein-/ Ausgabefeld aktiviert.
Schließen Sie das SA TA­Datenkabel an den roten SATAII-Anschluss (SAT AII _RED (PORT2)) an
Verbinden Sie das SATA-Datenkabel mit dem roten eSATAII­Anschluss (eSAT AII_BOTTOM)
2. Wenn Sie zwei eSATAII-Geräte mit Ihrem Motherboard verwenden möchten, müssen Sie sowohl den oberen als auch den unteren eSATAII-Anschluss am Ein-/Ausgabefeld aktivieren. Zum Aktivieren des oberen und unteren eSATAII-Anschlusses am Ein-/Ausgabefeld müssen Sie zunächst den roten SATAII-Anschluss (SATAII_RED (PORT2); siehe Seite 2, Nr. 21) und den roten eSATAII-Anschluss (eSATAII_BOTTOM; siehe Seite 2, Nr. 36) mit einem SATA-Datenkabel verbinden und danach den orangefarbenen SATAII-Anschluss (SATAII_ORANGE (PORT3); siehe Seite 2, Nr. 15) und den orangefarbenen eSATAII-Anschluss (eSATAII_TOP; Seite 2, Nr. 37) mit einem weiteren SATA-Datenkabel verbinden. Danach sind sowohl der obere als auch der untere eSATAII-Anschluss am Ein-/Ausgabefeld aktiviert.
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock ConRoe1333-eSATA2 Motherboard
9999
99
9999
Schließen Sie die SATA-Datenkabel sowohl an den roten SATAII-Anschluss (SATAII_RED (PORT2)) als auch an den orangefarbenen SATAII-Anschluss (SATAII_ORANGE (PORT3)) an
Achten Sie darauf, die SATAII- und eSATAII-Stecker an die Anschlüsse der passenden Farbe anzuschließen; nur so können die eSATAII-Funktionen richtig arbeiten.
Verbinden Sie die SA TA­Datenkabel sowohl mit dem roten eSATAII­Anschluss (eSATAII_ BOTTOM) als auch mit dem orangefarbenen eSATAII-Anschluss (eSATAII_TOP)
3. Verbinden Sie ein eSATAII-Gerät und den eSATAII-Anschluss am Ein-/ Ausgabefeld über das eSATAII-Gerätekabel mit dem eSATAII-Anschluss, an den Sie das SATA-Datenkabel angeschlossen haben.
Schließen Sie ein Ende des eSATAII-Gerätekabels an da s eSAT AII-Gerät a n
Verbinden Sie das andere Ende des eSATAII­Gerätekabels mit dem eSATAII-Anschluss am Ein-/Ausgabefeld
Deutsch
DeutschDeutsch
DeutschDeutsch
100100
100
100100
ASRock ConRoe1333-eSATA2 Motherboard
Loading...