Asus 90S8PA0000U200UET User Manual

RS700-E7/RS4

1U Rackmount Server User Guide

E7182

First Edition

February 2012

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not

limited to the implied warranties or conditions of merchantability or tness for a particular purpose. In no event shall ASUS, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of use or data,

interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product.

Specications and information contained in this manual ae furnished for informational use only, and are

subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe.

Contents

Contents ...................................................................................................... iii

Notices ........................................................................................................ vii

Safety information .................................................................................... viii

About this guide ......................................................................................... ix

Chapter 1: Product introduction

1.1 System package contents ........................................................... 1-2

1.2 Serial number label ...................................................................... 1-2

1.3 Systemspecications ................................................................. 1-3

1.4 Front panel features ..................................................................... 1-5

1.5 Rear panel features ...................................................................... 1-5

1.6 Internal features ........................................................................... 1-6

1.7 LED information ........................................................................... 1-7

1.7.1 Front panel LEDs ............................................................ 1-7

1.7.2 LAN (RJ-45) LEDs .......................................................... 1-7

1.7.3 HDD status LED .............................................................. 1-8

Chapter 2: Hardware setup

2.1 Chassis cover ............................................................................... 2-2

2.2 Central Processing Unit (CPU) ................................................... 2-3

2.2.1 Installing the CPU ........................................................... 2-3

2.2.2 Installing the CPU heatsink ............................................. 2-8

2.3 System memory ........................................................................... 2-9

2.3.1 Overview ......................................................................... 2-9

2.3.2 Memory Congurations ................................................... 2-9

2.4 Hard disk drives ......................................................................... 2-12

2.5 Expansion slot ............................................................................ 2-14

2.5.1 Installing an expansion card to the riser card bracket ... 2-14

2.5.2 Conguring an expansion card ..................................... 2-17

2.6 Cable connections ..................................................................... 2-18

2.7 SATAII/SAS backplane cabling ................................................. 2-19

2.8 Removable/optional components ............................................. 2-20

2.8.1 System fans .................................................................. 2-20

2.8.2 Redundant power supply module ................................. 2-21

2.8.3 Replacing optical drive (optional) .................................. 2-22

2.8.4 Connecting the Intel

ASRK Module (Optional) ............ 2-23

iii

Contents

2.8.5 Installing ASUS PIKE RAID card (optional) .................. 2-24

3.1 Friction Rail Kit Installation Guide ............................................. 3-2

3.1.1 Attaching the xing latches to the server ........................ 3-2

3.2 Ball-bearing rail kit items (optional) ........................................... 3-5

3.2.1 Attaching the rails to the server ...................................... 3-5

3.2.2 Attaching the rack rails .................................................... 3-6

3.2.3 Rackmounting the server ................................................ 3-7

4.1 Motherboard layouts .................................................................... 4-2

4.2 Jumpers ........................................................................................ 4-4

4.3 Internal connectors ...................................................................... 4-8

4.4 Internal LEDs .............................................................................. 4-13

Chapter 5: BIOS setup

5.1 Managing and updating your BIOS ............................................ 5-2

5.1.1 ASUS CrashFree BIOS 3 utility ...................................... 5-2

5.1.2 ASUS EZ Flash 2 Utility .................................................. 5-3

5.1.3 BUPDATER utility............................................................ 5-4

5.2 BIOS setup program .................................................................... 5-6

5.2.1 BIOS menu screen .......................................................... 5-7

5.2.2 Menu bar ......................................................................... 5-7

5.2.3 Menu items ..................................................................... 5-8

5.2.4 Submenu items ............................................................... 5-8

5.2.5 Navigation keys ............................................................... 5-8

5.2.6 General help ................................................................... 5-8

5.2.7 Conguration elds ......................................................... 5-8

5.2.8 Pop-up window ............................................................... 5-8

5.2.9 Scroll bar ......................................................................... 5-8

5.3 Main menu .................................................................................... 5-9

5.4 Advanced menu ......................................................................... 5-10

5.4.1 CPU Conguration ........................................................ 5-10

5.4.2 CPU Power Management Conguration ....................... 5-12

5.4.3 Chipset Conguration ................................................... 5-14

5.4.4 PCH SATA Conguration .............................................. 5-22

5.4.5 PCH SCU SAS Conguration ....................................... 5-23

5.4.6 PCI Subsystem Settings ............................................... 5-23

Contents

5.4.7 Onboard LAN Conguration .......................................... 5-29

5.4.8 USB Conguration ........................................................ 5-30

5.4.9 Trusted Computing ........................................................ 5-32

5.4.10 ACPI Settings ................................................................ 5-33

5.4.11 WHEA Conguration ..................................................... 5-34

5.4.12 APM .............................................................................. 5-34

5.4.13 Serial Port Console Redirection .................................... 5-35

5.4.14 ME Subsystem .............................................................. 5-38

5.4.15 Legacy Devices Conguration ...................................... 5-38

5.4.16 Runtime Error Logging .................................................. 5-39

5.5 Server Mgmt menu ..................................................................... 5-40

5.5.1 System Event Log ......................................................... 5-41

5.5.2 BMC network conguration ........................................... 5-42

5.6 Event Logs menu ....................................................................... 5-43

5.6.1 Change Smbios Event Log Settings ............................. 5-43

5.7 Boot menu .................................................................................. 5-45

5.8 Monitor menu ............................................................................. 5-47

5.9 Security menu ............................................................................ 5-48

5.10 Tool menu ................................................................................... 5-49

5.11 Exit menu .................................................................................... 5-50

Chapter6: RAIDconguration

6.1 Setting up RAID ............................................................................ 6-2

6.1.1 RAID denitions .............................................................. 6-2

6.1.2 Installing hard disk drives ................................................ 6-2

6.1.3 RAID controller selection ................................................ 6-3

6.1.4 Setting the RAID item in BIOS ........................................ 6-3

6.2 LSISoftwareRAIDCongurationUtility .................................... 6-4

6.2.1 Creating a RAID set ........................................................ 6-5

6.2.2 Adding or viewing a RAID conguration ........................6-11

6.2.3 Initializing the virtual drives ........................................... 6-12

6.2.4 Rebuilding failed drives ................................................. 6-16

6.2.5 Checking the drives for data consistency ..................... 6-18

6.2.6 Deleting a RAID conguration ....................................... 6-21

6.2.7 Selecting the boot drive from a RAID set ...................... 6-22

Contents

6.2.8 Enabling WriteCache .................................................... 6-23

6.3 Intel

Option ROM Utility ..................................................................... 6-24

6.4 Intel

(Windows) ................................................................................... 6-34

Chapter 7: Driver installation

7.1 RAID driver installation ............................................................... 7-2

7.2 Intel

7.3 Intel

7.4 VGA driver installation............................................................... 7-19

7.5 Intel

7.6 Microsoft .NET Framework 3.5 SP1 .......................................... 7-23

7.7 Intel

7.8 Intel

7.9 Management applications and utilities installation ................ 7-31

Rapid Storage Technology enterprise SCU/SATA

6.3.1 Creating a RAID set ...................................................... 6-26

6.3.2 Creating a Recovery set ............................................... 6-27

6.3.3 Deleting a RAID set ...................................................... 6-29

6.3.4 Resetting disks to Non-RAID ........................................ 6-30

6.3.5 Exiting the Intel

Rapid Storage Technology utility ........ 6-31

6.3.6 Rebuilding the RAID ..................................................... 6-31

6.3.7 Setting the Boot array in the BIOS Setup Utility ............ 6-33

Rapid Storage Technology enterprise Utility

6.4.1 Creating a RAID set ...................................................... 6-35

6.4.2 Change Volume Type .................................................... 6-37

6.4.3 Delete volume ............................................................... 6-38

6.4.4 Preferences ................................................................... 6-39

7.1.1 Creating a RAID driver disk ............................................ 7-2

7.1.2 Installing the RAID controller driver ................................ 7-5

Chipset Device Software installation ............................. 7-14

Network Connections Software installation.................. 7-16

C600 Series Chipset SAS RAID (SATA mode) Drivers . . 7-22

Rapid Storage Technology enterprise 3.0 installation . 7-24

I350 Gigabit Adapters Driver installation ....................... 7-27

7.9.1 Running the support DVD ............................................. 7-31

7.9.2 Drivers menu ................................................................. 7-31

7.9.3 Utilities menu ................................................................ 7-32

7.9.4 Make disk menu ............................................................ 7-32

7.9.5 Contact information ....................................................... 7-32

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING! The use of shielded cables for connection of the monitor to the

graphics card is required to assure compliance with FCC regulations. Changes

or modications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

This Class B digital apparatus complies with Canadian ICES-003.

REACH Information

Complying with the REACH (Registration, Evaluation, Authorization, and Restriction

of Chemicals) regulatory framework, we publish the chemical substances in our

products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.

vii

Safety information

Electrical Safety

• Before installing or removing signal cables, ensure that the power cables for the

system unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the electrical

outlet before relocating the system.

• When adding or removing any additional devices to or from the system, ensure

that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

• If the power supply is broken, do not try to x it by yourself. Contact a qualied

service technician or your dealer.

Operation Safety

• Any mechanical operation on this server must be conducted by certied or

experienced engineers.

• Before operating the server, carefully read all the manuals included with the server

package.

• Before using the server, ensure all cables are correctly connected and the power

cables are not damaged. If any damage is detected, contact your dealer as soon as possible.

• To avoid short circuits, keep paper clips, screws, and staples away from

connectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a stable

surface.

viii

This product is equipped with a three-wire power cable and plug for the user’s safety. Use the power cable with a properly grounded electrical outlet to avoid electrical shock.

Lithium-Ion Battery Warning

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

CD-ROM Drive Safety Warning

CLASS 1 LASER PRODUCT

Heavy System

CAUTION! This server system is heavy. Ask for assistance when moving or

carrying the system.

DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

About this guide

Audience

This user guide is intended for system integrators, and experienced users with at

least basic knowledge of conguring a server.

Contents

This guide contains the following parts:

1. Chapter 1: Product introduction

This chapter describes the general features of the server, including sections

on front panel and rear panel specications.

2. Chapter 2: Hardware setup

This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.

3. Chapter 3: Installation options

This chapter describes how to install optional components into the barebone server.

4. Chapter 4: Motherboard information

This chapter gives information about the motherboard that comes with the server. This chapter includes the motherboard layout, jumper settings, and connector locations.

5. Chapter 5: BIOS information

This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters.

6. Chapter6:RAIDconguration

This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

7 Chapter 7: Driver installation

This chapter provides instructions for installing the necessary drivers for different system components.

Conventions

To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when

trying to complete a task.

CAUTION: Information to prevent damage to the components when

trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text

Italics

<Key> Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or Return key.

<Key1+Key2+Key3> If you must press two or more keys simultaneously,

the key names are linked with a plus sign (+).

Example: <Ctrl+Alt+D>

Command

exactly as shown, then supply the required item or value enclosed in brackets.

Example: At the DOS prompt, type the command line:

Indicates a menu or an item to select.

Used to emphasize a word or a phrase.

Means that you must type the command

format A:/S

References

Refer to the following sources for additional information, and for product and software updates.

1. ASUS Server Web-based Management (ASWM) user guide

This manual tells how to set up and use the proprietary ASUS server management utility.

2. ASUS websites

The ASUS websites worldwide provide updated information for all ASUS hardware and software products. Refer to the ASUS contact information.

Chapter 1

This chapter describes the general features of the chassis kit. It includes sections on front panel and rear panel

specications.

Product introduction

1.1 System package contents

Check your system package for the following items.

Model Name RS700-E7/RS4 Chassis ASUS R12D 1U Rackmount Chassis

Motherboard ASUS Z9PP-D24 Server Board Component 2 x800W Redundant Power Supply (varies by territories)

Accessories 1 x RS700-E7/RS4 User’s Guide

Optional Items Second 800W Redundant Power Supply Module

*ASUS System Web-based Management

1 x SAS 3.5” HDD Backplane (BP4LX-R10A) 4 x hot-swap 3.5” HDD trays (varies by territories) 1 x Front I/O Board (LED board, FPB-AR14) 2 x Riser Card (RE16L-R12D, RE16R-R12D) 8 x System Fans (40 x 40 x 56mm)

1 x ASWM Enterprise User’s Guide 1 x RS700-E7/RS4 Support CD 1 x ASWM Enterprise Support CD 1 x Bag of Screws 2 x CPU Heatsink (varies by territories) 2 x AC Power Cable

1 x Friction Rail Kit

CPU Heatsink

Slim type DVD-RW Semi-ball Bearing Rail Kit

If any of the above items is damaged or missing, contact your retailer.

1.2 Serial number label

Before requesting support from the ASUS Technical Support team, you must take note of the product’s serial number containing 14 characters such as xxS0xxxxxxxxxx. See the gure below.

With the correct serial number of the product, ASUS Technical Support team

members can then offer a quicker and satisfying solution to your problems.

RS700-E7/RS4

xxS0xxxxxxxxxx

Chapter 1: Product introduction1-2

1.3 Systemspecications

The ASUS RS700-E7/RS4 feature the ASUS Z9PP-D24 server board. The

server supports Intel® Socket-R LGA2011 Xeon® series processors with EM64T technology, plus other latest technologies through the chipsets onboard.

Model Name RS700-E7/RS4

Processor / System Bus

Core Logic

ASUS Features

Memory

Expansion Slots

Storage

HDD Bays

Networking LAN

Graphic VGA

Smart Fan ASWM

Enterprise Total Slots

Capacity

Memory Type

Memory Size

Total PCI/PCI-X/ PCI-E Slots

Slot Type Additional Slot

SATA Controller

SAS Controller

I = internal A or S will be hot-swappable

2 x Socket-R (LGA2011) 8/6/4 Core Intel QPI 6.4 / 7.2 / 8.0 GT/s

Intel

√

24 (4-channel per CPU, 12 DIMMs per CPU) Maximum up to 512GB (RDIMM)

Maximum up to 128GB (UDIMM) Maximum up to 768GB (LRDIMM)

DDR3 1600 / 1333 / 1066 / 800 Reg DIMM / Unbuffered DIMM with ECC / LRDIMM

1GB, 2GB, 4GB, 8GB, 16GB and 32GB (RDIMM) 1GB, 2GB, 4GB and 8GB (UDIMM) 8GB, 16GB, 32GB (LRDIMM)

2+1

2 x PCI-E G3 x16 (x16 Link) ( Full-height/Half-lengh)

1 x PIKE slot for storage enhancement

Intel <AHCI>

2x SATA 3Gb/s ports 1x ISATA1 port (2 x SATA 3 Gb/s+2 x SATA 6Gb/s) Intel RSTe (For Windows only)

- Supports S/W RAID 0,1,10 & 5) LSI MegaRAID (for Linux / Windows):

- Supports software RAID 0, 1 & 10\

<SCU>

1x ISAS1 port (4 x SATA 3Gb/s) Intel RSTe (For Windows only)

- Supports S/W RAID 0,1,10 & 5)

Optional:

ASUS PIKE 2008 8-port SAS2 6G RAID card ASUS PIKE 2008/IMR 8-port SAS2 6G RAID card ASUS PIKE 2108 8-port SAS2 6G H/W RAID card

For <SCU>:

ASRK #1 SAS 6G RAID kit (RAID 0/1/10) ASRK #2 SAS 6G RAID kit (RAID 0, 1, 10 & 5)

Xeon E5-2600 Series (Up to TDP=150W)

C602 chipset

C602 chipset:

4 x Hot-swap 3.5” SATA/SAS HDD Bays

4 x Intel

I350-AM4 + 1 x Mgmt LAN

Aspeed AST2300 + 16MB VRAM

(continued on the next page)

ASUS RS700-E7/RS4 1-3

Model Name RS700-E7/RS4

5 x RJ-45 ports (1 for ASMB6-iKVM) 4 x USB 2.0 ports (Front x 2, Rear x 2)

Onboard I/O

OS Support

1 x VGA port 1 x PS/2 keyboard port 1 x PS/2 mouse port

Server 2008 R2

Windows Windows® Server 2008 Enterprise 32 / 64-bit

Windows

Server 2003 R2 Enterprise 32 / 64-bit

RedHat® Enterprise Linux AS5.7, 6.1 32 / 64-bit SuSE® Linux Enterprise Server 11.1 32 / 64-bit (Subject to change without any notice)

Out of Band Management Solution

Remote

Hardware

Software Dimension (HH x WW x DD) Net Weight Kg (CPU, DRAM &

HDD not inclu ded)

Power Supply

Power Rating

On-Board ASMB6-iKVM for KVM-over-IP support

ASUS ASWM Enterprise

689.5mm x 444mm x 43.4mm (1U)

18 Kg

800W (Delta 80Plus Platinum level) 1+1 Redundant Power Supply (Default with one Power Supply Module)

Input:

800W: 100 - 127Vac / 9.9A, 200-240Vac / 4.79A, 47 - 63Hz, Class 1 Operation temperature: 10°C–35°C

Environment

Non operation temperature: -40°C–70°C Non operation humidity: 20%–90% ( Non-condensing)

*Specicationsaresubjecttochangewithoutnotice.

Chapter 1: Product introduction1-4

1.4 Front panel features

The barebone server displays a simple yet stylish front panel with easily accessible features. The power and reset buttons, LED indicators, slim type optical drive, and

two USB ports are located on the front panel.

Refer to section 1.7.1 Front panel LEDs for the LED descriptions.

Rack screw

HDD 1 HDD 2 HDD 3 HDD 4

Optical drive

USB ports

HDD Access LED

LAN2 LED LAN1 LED

Message LED

Reset button

Location LED

Location switch

Rack screw

Power button

Power LED

Factory shipment (default):

• Connect HDD1 - HDD4 to ISAS1 <AHCI> to support 2 x SATA 6Gb/s (HDD1/ HDD2) and 2 x SATA 3Gb/s (HDD3/HDD4). If you want SAS HDD support,

please upgrade with a PIKE RAID card or ASRK RAID kit.

• Refer to section

2.8.5 Installing ASUS PIKE RAID card

for the

descriptions.

1.5 Rear panel features

The rear panel includes the expansion slots, system power socket, and rear fans.

The middle part includes the I/O shield with openings for the rear panel connectors

on the motherboard.

LAN port 1

LAN port 2

Expansion slot

LAN port 3

LAN port 4

USB ports

PS/2 keyboard port

Expansion slot

DMLAN port*

PS/2 mouse port

VGA port

(Optional)

Redundant power

Second

connector

Power cord

• The ports for the PS/2 keyboard, PS/2 mouse, serial port, USB, VGA, and Gigabit LAN do not appear on the rear panel if motherboard is not present.

• *The port is for ASUS ASMB6-iKVM controller card only.

ASUS RS700-E7/RS4 1-5

1.6 Internal features

The barebone server includes the basic components as shown.

1. Power supply and power fan

2. PCI-E G3 x16 slot (x16 link) (FH/HL)

3. PIKE Slot

4. ASUS Z9PP-D24 Server Board

5. System fans

6. SATA/SAS backplane

(hidden)

7. 4 x HDD trays

8. Front LED Board (FPB-AR14)

9. Slim-type optical drive

The barebone server does not include a oppy disk drive. Connect a USB oppy disk drive to any of the USB ports on the front or rear panel if you need to use a oppy disk.

A protection lm is pre-attached to the front cover before shipping. Please remove the protection lm before turning on the system for proper heat

dissipation.

*WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY

Chapter 1: Product introduction1-6

1.7 LED information

1.7.1 Front panel LEDs

HDD Access LED

LAN2 LED

LAN1 LED

LED Icon Display status Description

Power LED

HDD Access LED

Message LED

Location LED

LAN LEDs

Message LED

Power LED

Location LED

ON System power ON

OFF

Blinking

OFF

Blinking

OFF

Blinking

No activity

Read/write data into the HDD System is normal; no incoming event ASWM indicates a HW monitor event

Normal status Location switch is pressed (Press the location switch again to turn off) No LAN connection LAN is transmitting or receiving data LAN connection is present

1.7.2 LAN (RJ-45) LEDs

SPEED LED

ACT/LINK LED

ACT/LINK LED SPEED LED

Status Description Status Description

OFF No link OFF 10 Mbps connection

GREEN Linked ORANGE 100 Mbps connection

BLINKING Data activity GREEN 1 Gbps connection

ASUS RS700-E7/RS4 1-7

1.7.3 HDD status LED

HDD status LED

HDD Activity LED

SATAII/SAS HDD LED Description

GREEN ON SATAII/SAS HDD power ON

HDD Status LED

HDD Activity LED

RED ON

GREEN/ RED

GREEN Blinking Read/write data from/into the SATAII/SAS HDD

Blinking RAID rebuilding

HDD has failed and should be swapped immediately

Chapter 1: Product introduction1-8

Chapter 2

This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.

Hardware setup

2.1 Chassis cover

Removing the rear cover

1. Loosen the two thumbscrews on the rear panel to release the rear cover from the chassis.

Thumbscrews

2. Firmly hold the cover and slide it

toward the rear panel for about half an inch until it is disengaged from the chassis.

1/2 inch distance

3. Lift the cover from the chassis.

Chapter 2: Hardware setup2-2

Z9PP-D24

Z9PP-D24 CPU LGA2011 Socket

CPU2

CPU1

2.2 Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA2011 socket designed for the

Intel® Xeon E5-2600 family processor.

• Upon purchase of the motherboard, ensure that the PnP cap is on

the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP

cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.

• Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA2011 socket.

• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/

incorrect removal of the PnP cap.

2.2.1 Installing the CPU

To install a CPU:

1. Locate the CPU socket on the motherboard.

Before installing the CPU, ensure that the socket box is facing towards you and

the load lever is on your left.

2-3ASUS RS700-E7/RS4

2. Press the left load lever with your

thumb (A), then move it to the left

(B) until it is released from the

retention tab.

To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.

3. Slightly lift the load lever in the direction of the arrow.

Load lever

4. Press the right load lever with your

thumb (C), then move it to the right (D) until it is released from the retention tab. Lift the load lever in the direction of the arrow (E).

Chapter 2: Hardware setup2-4

5. Push the left load lever (F) to lift the load plate (G).

6. Position the CPU over the socket, ensuring that the triangle mark is on the top-right corner of the socket.

Triangle

mark

The CPU ts in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU!

7. Remove the PnP cap (H) from the CPU socket and close the load plate (I).

2-5ASUS RS700-E7/RS4

8. Push down the right load lever (J),

ensuring that the edge of the load

plate is xed by the lever (K).

9. Insert the right load lever under the retention tab.

10. Push down the left load lever (L),

and then insert the lever under the retention tab (M).

Chapter 2: Hardware setup2-6

11. Apply some Thermal Interface Material to the exposed area of the CPU that the heatsink will be in contact with, ensuring that it is spread in an even thin layer.

Some heatsinks come with preapplied thermal paste. If so, skip this step.

The Thermal Interface Material is toxic and inedible. DO NOT eat it. If it gets into your eyes or touches your skin, wash it off immediately, and seek professional medical help.

2-7ASUS RS700-E7/RS4

2.2.2 Installing the CPU heatsink

To install the CPU heatsink:

1. Place the heatsink on top of the installed CPU, ensuring that the four fasteners match the holes on the motherboard.

2. Twist each of the four screws with

a Philips (cross) screwdriver just enough to attach the heatsink to

the motherboard. When the four

screws are attached, tighten them one by one to completely secure the heatsink.

Tighten the four heatsink screws in a

diagonal sequence.

Chapter 2: Hardware setup2-8

2.3 System memory

Z9PP-D24

Z9PP-D24 240-pin DDR3 DIMM sockets

DIMM_C3

DIMM_C2

DIMM_C1

DIMM_D3

DIMM_D2

DIMM_D1

DIMM_E1

DIMM_E2

DIMM_E3

DIMM_F1

DIMM_F2

DIMM_F3

DIMM_H2

DIMM_H3

DIMM_H1

DIMM_G3

DIMM_G2

DIMM_G1

DIMM_A2

DIMM_A1

DIMM_A3

DIMM_B1

DIMM_B2

DIMM_B3

2.3.1 Overview

The motherboard comes with 12 (per CPU) Double Data Rate 3 (DDR3) Dual Inline

Memory Modules (DIMM) sockets.

A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules

are developed for better performance with less power consumption.

The gure illustrates the location of the DDR3 DIMM sockets:

2.3.2 MemoryCongurations

You may install 1GB, 2GB, 4GB, 8GB, 16GB and 32GB* RDIMMs or

4GB and 8GB* with ECC/Non-ECC UDIMMs or

the DIMM sockets using the memory congurations in this section.

1CPUConguration(mustonCPU1)(QuadRank)

DIMM_A3 DIMM_A2 DIMM_A1 DIMM_B3 DIMM_B2 DIMM_B1 1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs

1CPUConguration(mustonCPU1)(QuadRank)

DIMM_C3 DIMM_C2 DIMM_C1 DIMM_D3 DIMM_D2 DIMM_D1 1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs

8GB, 16GB and 32GB* LR-DIMMs into

V V V V V V V V V V

V V V V

1GB, 2GB,

2-9ASUS RS700-E7/RS4

2CPUConguration(SingleRank,DualRank)

DIMM_A3 DIMM_A2 DIMM_A1 DIMM_B3 DIMM_B2 DIMM_B1 1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs 12 DIMMs 16 DIMMs 20 DIMMs 24 DIMMs

2CPUConguration(SingleRank,DualRank)

1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs 12 DIMMs 16 DIMMs 20 DIMMs 24 DIMMs

2CPUConguration(SingleRank,DualRank)

1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs 12 DIMMs 16 DIMMs 20 DIMMs 24 DIMMs

2CPUConguration(SingleRank,DualRank)

1 DIMMs 2 DIMMs 4 DIMMs 8 DIMMs 12 DIMMs 16 DIMMs 20 DIMMs 24 DIMMs

V V V V V V V V V V V V

DIMM_C3 DIMM_C2 DIMM_C1 DIMM_D3 DIMM_D2 DIMM_D1

V V V V V V V V V V V V

DIMM_E3 DIMM_E2 DIMM_E1 DIMM_F3 DIMM_F2 DIMM_F1

V V V V V V

DIMM_G3 DIMM_G2 DIMM_G1 DIMM_H3 DIMM_H2 DIMM_H1

V V V V V V

V V V V V V V V

V V V V V V V

V V V V

• *Refer to ASUS Server AVL for latest update.

• Start installing the DIMMs from slot A1 (light blue).

• Always install DIMMs with the same CAS latency. For optimum

compatibility, it is recommended that you obtain memory modules from the same vendor.

Chapter 2: Hardware setup2-10

2.3.3 Installing a DIMM on a single clip DIMM socket

1. Unlock a DIMM socket by pressing

the retaining clip outward.

2. Align a DIMM on the socket

such that the notch on the DIMM matches the DIMM slot key on the socket.

A DIMM is keyed with a notch so that it ts in only one direction. DO NOT force

a DIMM into a socket in the wrong direction to avoid damaging the DIMM.

3. Hold the DIMM by both of its ends,

then insert the DIMM vertically into the socket. Apply force to both ends of the DIMM simultaneously until the retaining clip snaps back into place, and the DIMM cannot be pushed in any further to ensure proper sitting of the DIMM.

Always insert the DIMM into the socket VERTICALLY to prevent DIMM notch

damage.

• To install two or more DIMMs, refer to the user guide bundled in the

motherboard package.

• Refer to the user guide for qualied vendor lists of the memory modules.

DIMM notch

DIMM slot key

Unlocked retaining clip

Locked Retaining Clip

Removing a DIMM from a single clip DIMM socket

1. Press the retaining clip outward to

unlock the DIMM.

2. Remove the DIMM from the socket.

Support the DIMM lightly with your ngers when pressing the retaining clips. The DIMM might get damaged when it ips out with extra force.

2-11ASUS RS700-E7/RS4

2.4 Hard disk drives

The system supports four hot-swap SATAII/SAS hard disk drives. The hard disk drive installed on the drive tray connects to the motherboard SATAII/SAS ports via the SATAII/SAS backplane.

To install a hot-swap SATAII/SAS HDD:

1. Release a drive tray by pushing the spring lock to the right, then pulling the tray lever outward. The drive tray ejects slightly after you pull out the lever.

2. Firmly hold the tray lever and pull

the drive tray out of the bay.

spring lock

3. Take note of the drive tray holes.

Each side has three holes to t

different types of hard disk drives. Use two screws on each side to secure the hard disk drive.

4. Place a SATAII/SAS hard disk drive

on the tray, then secure it with four screws.

Chapter 2: Hardware setup2-12

+ 158 hidden pages