ASRock X58 Extreme3 User Manual

Page 1
Copyright Notice:Copyright Notice:
Copyright Notice:
Copyright Notice:Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documen­tation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identifica­tion or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:
Disclaimer:Disclaimer:
Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published February 2010
Copyright©2010 ASRock INC. All rights reserved.
ASRock X58 Extreme3 Motherboard
EnglishEnglish
EnglishEnglish
English
11
1
11
Page 2
English
EnglishEnglish
EnglishEnglish
22
2
22
Motherboard LayoutMotherboard Layout
Motherboard Layout
Motherboard LayoutMotherboard Layout
1 PS2_USB_PWR1 Jumper 22 Dr. Debug 2 CPU Fan Connector (CPU_FAN1) 23 Reset Switch (RSTBTN) 3 A TX 12V Power Connector (A TX12V1) 24 Power Switch (PWRBTN) 4 1366-Pin CPU Socket 25 USB 2.0 Header (USB6_7, Blue) 5 Power Fan Connector (PWR_FAN1) 26 8Mb SPI Flash 6 Chassis Fan Connector (CHA_FAN2) 27 Front Panel IEEE 1394 Header 7 3 x 240-pin DDR3 DIMM Slots (FRONT_1394, White)
(Triple Channel: DDR3_A1, DDR3_B1, DDR3_C1 28 Chassis Fan Connector (CHA_FAN1)
; White) 29 TPM Header (TPM1) 8 ATX Power Connector (ATXPWR1) 30 COM Port Header (COM1) 9 System Panel Hea der (P ANEL1, White) 31 Floppy Connector (FLOPPY1) 10 USB 2.0 Header (USB8_9, Blue) 32 HDMI_SPDIF Header (HDMI_SPDIF1, White) 11 3 x 240-pin DDR3 DIMM Slots 33 Infrared Module Header (IR1)
(Triple Channel: DDR3_A2, DDR3_B2, DDR3_C2 34 PCI Express x16 Slot (PCIE4, White)
; Blue) 35 Chassis Intrusion Header (CI1) 12 SAT A3 Conne ctor (SA TA3_2, White) 36 PCI Slot (PCI2) 13 SATA3 Connector (SAT A3_1, White) 37 PCI Express 2.0 x16 Slot (PCIE3, Blue) 14 Primary IDE Connector (IDE1, Blue) 38 PCI Slot (PCI1) 15 Clear CMOS Jumper (CLRCMOS1) 39 PCI Express x1 Slot (PCIE2, White) 16 SAT AII Connector (SA T AII_1_2, Blue) 40 PCI Express 2.0 x16 Slot (PCIE1, Blue) 17 SAT AII Connector (SA T AII_3_4, Blue) 41 North Bridge Controller 18 SAT AII Connector (SA T AII_5_6, Blue) 42 North Bridge Fan Connector (NB_FAN1) 19 South Bridge Controller 43 Internal Audio Connector: CD1 (Black) 20 Power LED Header (PLED1) 44 Front Panel Audio Header 21 Chassis Speaker Header (SPEAKER 1, White) (HD_AUDIO1, White)
ASRock X58 Extreme3 Motherboard
Page 3
I/O PI/O P
I/O P
I/O PI/O P
* 5 LAN RJ-45 Port 14 USB 2.0 Ports (USB23)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.
See the table below for connection details in accordance with the type of speaker you use.
anelanel
anel
anelanel
1 PS/2 Mouse Port (Green) ** 10 Front Speaker (Lime) 2 Coaxial SPDIF Out Port 11 Microphone (Pink) 3 USB 2.0 Port (USB0) 12 USB 3.0 Ports 4 IEEE 1394 Port (IEEE 1394) 13 USB 2.0 Ports (USB45)
6 Side Speaker (Gray) 15 Powered eSA T AIII/USB 2.0 Connector 7 Rear Speaker (Black) 16 Optical SPDIF Out Port 8 Central / Bass (Orange) 17 Clear CMOS Switch (CLRCBTN) 9 Line In (Light Blue) 18 PS/2 Keyboard Port (Purple)
Activity/Link LED SPEED LED
Status Description Status Description
Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker
2 V -- -- -­4VV---­6 VVV-­8 VVVV
LAN Port LED Indications
TABLE for Audio Output Connection
(No. 10) (No. 7) (No. 8) (No. 6)
ACT/LINK LED
LAN Port
SPEED LED
ASRock X58 Extreme3 Motherboard
EnglishEnglish
EnglishEnglish
English
33
3
33
Page 4
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on your system. Please follow below instructions according to the OS you install.
For Windows® XP / XP 64-bit OS: Please click “VIA HD Audio Deck” icon. Click “Jack” and then click “Configuration”. In “Configuration” screen, please check the item “Independent Headphone”.
For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Please click “VIA HD Audio Deck” icon. Click “Advanced Options” on the right side on the bottom. In “Advanced Options” screen, please check the item “Independent Headphone”.
English
EnglishEnglish
EnglishEnglish
44
4
44
ASRock X58 Extreme3 Motherboard
Page 5
1. Introduction1. Introduction
1. Introduction
1. Introduction1. Introduction
Thank you for purcha sing ASRock X58 Extreme3 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard a nd step-by-ste p installation guide. More detailed information of the motherboard can be f ound in the user manual presented in the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp
1.1 Package Contents1.1 Package Contents
1.1 Package Contents
1.1 Package Contents1.1 Package Contents
ASRock X58 Extreme3 Motherboard
(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)
ASRock X58 Extreme3 Quick Installation Guide ASRock X58 Extreme3 Support CD 1 x 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable 1 x Ribbon Cable for a 3.5-in Floppy Drive 4 x Serial ATA (SATA) Data Cables (Optional) 2 x Serial ATA (SATA) HDD Power Cables (Optional) 1 x I/O Panel Shield 1 x ASRock SLI_Bridge_2S Card
ASRock X58 Extreme3 Motherboard
EnglishEnglish
EnglishEnglish
English
55
5
55
Page 6
English
EnglishEnglish
EnglishEnglish
1.21.2
SpecificationsSpecifications
1.2
Specifications
1.21.2
SpecificationsSpecifications
Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm
- All Solid Capacitor design (100% Japan-made high-quality Conductive Polymer Capacitors)
CPU - Intel® Socket 1366 CoreTM i7 Processor Extreme Edition /
Chipset - Northbridge: Intel® X58
Memory - Triple Cha nnel DDR3 Memory Technology (see CAUTION 3)
Expansion Slot - 2 x PCI Express 2.0 x16 slots (blue @ x16 mode)
Audio - 7.1 CH HD Audio with Content Protection
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
Rear Panel I/O I/O Panel
TM
Core
i7 Processor Supports Intel® Dynamic Speed
Technology
- System Bus up to 6400 MT/s; Intel® QuickPath Interconnect
- Advanced V8 Power Phase Design
- Supports Hyper-Threading Technology (see CAUTION 1)
- Supports Untied Overclocking Technology (see CAUTION 2)
- Supports EM64T CPU
- Southbridge: Intel® ICH10R
- 6 x DDR3 DIMM slots
- Supports DDR3 2000(OC)/1866(OC)/1600(OC)/1333(OC)/ 1066 non-ECC, un-buffered memory
- Supports DDR3 ECC, un-buffered memory with Intel Workstation 1S Xeon® processors 3500 series
- Max. capacity of system memory: 24GB (see CAUTION 4)
- Supports Intel® Extreme Memory Profile (XMP)
- 1 x PCI Express x16 slot (white @ x4 mode) (Double-wide slot spacing between each PCI-E slot)
- 1 x PCI Express x1 slot
- 2 x PCI slots
- Supports ATITM CrossFireXTM and Quad CrossFireX
- Supports NVIDIA® SLITM and Quad SLI
- DAC with 110dB dynamic range (VIA® VT2020 Audio Codec)
- Premium Blu-ray audio support
- Realtek RTL81 11DL
- Supports Wake-On-LAN
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Coaxial SPDIF Out Port
- 1 x Optical SPDIF Out Port
TM
®
TM
66
6
66
ASRock X58 Extreme3 Motherboard
Page 7
- 1 x Optical SPDIF Out Port
- 5 x Ready-to-Use USB 2.0 Ports
- 1 x Powered eSATAIII/USB 2.0 Connector
- 2 x Ready-to-Use USB 3.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
- 1 x IEEE 1394 Port
- 1 x Clear CMOS Switch
- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/ Line in/Front Speaker/Microphone (see CAUTION 5)
SATA3 - 2 x SATA3 6.0Gb/s connectors by Marvell SE9128, support
hardware RAID (RAID 0 and RAID 1), NCQ, AHCI and “Hot Plug” functions (SATA3_2 connector is shared with eSATA3 port)
USB3.0 - 2 x USB3.0 ports by NEC UPD720200, support USB 1.0/2.0/
3.0 up to 5Gb/s
Connector - 6 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 10, RAID 5 and Intel Matrix Storage), NCQ, AHCI and “Hot Plug” functions
- 2 x SATA3 6.0Gb/s connectors
- 1 x ATA133 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
- 1 x COM port header
- 1 x HDMI_SPDIF header
- 1 x IEEE 1394 header
- 1 x TPM header
- 1 x Chassis Intrusion header
- 1 x Power LED header
- CPU/Chassis/NB/Power FAN connector
- 24 pin ATX power connector
- 8 pin 12V power connector
- CD in header
- Front panel audio connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports) (see CAUTION 6)
- 1 x Dr. Debug (7-Segment Debug LED)
Smart Switch - 1 x Clear CMOS Switch with LED
- 1 x Power Switch with LED
- 1 x Reset Switch with LED
BIOS Feature - 8Mb AMI BIOS
- AMI Legal BIOS
- Supports “Plug and Play”
ASRock X58 Extreme3 Motherboard
EnglishEnglish
EnglishEnglish
English
77
7
77
Page 8
- ACPI 1.1 Compli ance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- CPU, VCCM, IOH, ICH, VTT, IOH/ICH PCIE, CPU PLL, IOH CSI, VCORE Voltage Multi-adjustment
- Supports I. O. T. (Intelligent Overclocking Technology)
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version),
ASRock Software Suite (CyberLink DVD Suite and Creative Sound Blaster X-Fi MB) (OEM and Trial Version)
Unique Feature - ASRock OC Tuner (see CAUTION 7)
- Intelligent Energy Saver (see CAUTION 8)
- Instant Boot
- ASRock Instant Flash (see CAUTION 9)
- ASRock OC DNA (see CAUTION 10)
- Hybrid Booster:
- CPU Frequency Stepless Control (see CAUTION 11)
- ASRock U-COP (see CAUTION 12)
- Boot Failure Guard (B.F.G.)
- Good Night LED Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing
- CPU/Chassis/NB/Power Fan Tachometer
- CPU Quiet Fan
- CPU/Chassis Fan Multi-Speed Control
- CASE OPEN detection
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft® Windows® 7 / 7 64-bit / Vista
TM
/ VistaTM 64-bit
/ XP / XP 64-bit compliant
Certifications - FCC, CE, WHQL
- ErP/EuP Ready (ErP/EuP ready power supply is required)
(see CAUTION 13)
* For detailed product information, please visit our website: http://www.asrock.com
English
EnglishEnglish
EnglishEnglish
88
8
88
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third­party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
ASRock X58 Extreme3 Motherboard
Page 9
CAUTION!
1. About the setting of “Hyper Threading Technology”, please check page 62 of “User Manual” in the support CD.
2. This motherboard supports Untied Overclocking Technology. Please read “Untied Overclocking Technology” on page 37 for details.
3. This motherboard supports Triple Channel Memory Technology. Before you implement Triple Channel Memory Technology, make sure to read the installation guide of memory modules on page 16 for proper installation.
4. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 7 / VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limitation.
5. For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.
6. Power Management for USB 2.0 works fine under Microsoft® Windows® 7 64-bit / 7 / VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2.
7. It is a user-friendly ASRock overclocking tool which allows you to surveil your system by hardware monitor function and overclock your hardware devices to get the best system performance under Windows® environment. Please visit our website for the operation procedures of ASRock OC Tuner . ASRock website: http://www.asrock.com
8. Featuring an advanced proprietary hardware and software design, Intelligent Energy Saver is a revolutionary technology that delivers unparalleled power savings. In other words, it is able to provide exceptional power saving and improve power efficiency without sacrificing computing performance. Please visit our website for the operation procedures of Intelligent Energy Saver. ASRock website: http://www.asrock.com
9. ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS-DOS or Windows®. With this utility, you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without prepar­ing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system.
ASRock X58 Extreme3 Motherboard
EnglishEnglish
EnglishEnglish
English
99
9
99
Page 10
10. The software name itself – OC DNA literally tells you what it is capable of. OC DNA, an exclusive utility developed by ASRock, provides a conve­nient way for the user to record the OC settings and share with others. It helps you to save your overclocking record under the operating system and simplifies the complicated recording process of overclocking settings. With OC DNA, you can save your OC settings as a profile and share with your friends! Your friends then can load the OC profile to their own system to get the same OC settings as yours! Please be noticed that the OC profile can only be shared and worked on the same motherboard.
11. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.
12. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU a nd the he atsink when you install the PC syste m.
13. EuP, stands for Energy Using Product, was a provision regulated by European Union to define the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1.00W in off mode condition. To meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required. According to Intel’s suggestion, the EuP ready power supply must meet the standard of 5v standby power efficiency is higher than 50% under 100 mA current consumption. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details.
English
EnglishEnglish
EnglishEnglish
1010
10
1010
ASRock X58 Extreme3 Motherboard
Page 11
TMTM
TM
1.31.3
Two SLITwo SLI
1.3
Two SLI
1.31.3
Two SLITwo SLI
(for Windows® XP / XP 64-bit / VistaTM / VistaTM 64-bit / 7 / 7 64-bit)
* For the latest updates of the supported PCI Express VGA card list for SLI please visit our website for details. ASRock website: http://www.asrock.com/support/index.htm
TMTM
Graphics Card Support List Graphics Card Support List
Graphics Card Support List
Graphics Card Support List Graphics Card Support List
Chipset Model Name Chipset Name Driver Vendor NVIDIA
Gigabyte GV -NX88T256H GeForce 8800 GT 182.50 Gigabyte GV -NX88S512H-B GeForce 8800 GTS 182.50 LEADTEK PX8800 GTX T DH GeForce 8800 GTX 182.50 Chaintech GES96GT-A1512P GeForce 9600 GT 182.50 ASUS EN9800GT T DP/HT DP/512M GeForce 9800GT 182.50 LEADTEK PX9800GTX GeForce 9800GTX 182.50 LEADTEK PX9800 GTX+ GeForce 9800GTX+ 182.50 GIGABYTE GV-N26-896H-B GeForce GTX260 182.50
TM
Mode,
ASRock X58 Extreme3 Motherboard
1111
11
1111
EnglishEnglish
EnglishEnglish
English
Page 12
TMTM
TM
1.41.4
Two CrossFireXTwo CrossFireX
1.4
Two CrossFireX
1.41.4
Two CrossFireXTwo CrossFireX
(for Windows® VistaTM / VistaTM 64-bit / 7 / 7 64-bit)
Chipset Model Name Chipset Name Driver Vendor ATI
MSI RX2600PRO-T2D256EZ Radeon HD 2600PRO Catalyst 9.1 Gigabyte GV -RX26T256HP-B Radeon HD 2600XT Catalyst 9.1 Powercolor AX3650 512MMD3-XP RADEON 3650 Catalyst 9.1 Gigabyte G V-RX385256H-B RADEON 3850 Catalyst 9.1 Powercolor AX3870 512MD4-H RADEON 3870 Catalyst 9.1 Powercolor AX3870X2 1GBD3-H RADEON 3870 Catalyst 9.1 Gecube GC-HD485PG3-E3 RADEON 4850 Catalyst 9.1
TMTM
Graphics Card Support List Graphics Card Support List
Graphics Card Support List
Graphics Card Support List Graphics Card Support List
English
EnglishEnglish
EnglishEnglish
* For the latest updates of the supported PCI Express VGA card list for CrossFireX ASRock website: http://www.asrock.com/support/index.htm
TM
Mode, please visit our website for details.
1212
12
1212
ASRock X58 Extreme3 Motherboard
Page 13
Catalyst 9.1 Catalyst 9.1 Catalyst 9.1 Catalyst 9.1 Catalyst 9.1
2.2.
InstallationInstallation
2.
Installation
2.2.
InstallationInstallation
Pre-installation PrecautionsPre-installation Precautions
Pre-installation Precautions
Pre-installation PrecautionsPre-installation Precautions
Take note of the following precautions before you install mother­board components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.
2.12.1
CPU InstallationCPU Installation
2.1
CPU Installation
2.12.1
CPU InstallationCPU Installation
For the installation of Intel 1366-Pin CPU, please f ollow the ste ps below.
1366-Pin Socket Overview
Before you insert the 1366-Pin CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
ASRock X58 Extreme3 Motherboard
1313
13
1313
EnglishEnglish
EnglishEnglish
English
Page 14
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear re­tention tab.
Step 1-2. Rotate the load lever to fully open posi-
tion at approxi mately 135 degrees .
Step 1-3. Rotate the load plate to fully open posi-
tion at approxi mately 100 degrees .
Step 2. Remove PnP Cap (Pick a nd Pla ce Cap).
1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
2. This cap must be placed if returning the motherboard for after service.
Step 3. Insert the 1366-Pin CPU:
Step 3-1. Hold the CPU by the edges where are
marked with black lines.
black line
black line
English
EnglishEnglish
EnglishEnglish
1414
14
1414
Step 3-2. Orient the CPU with IHS (Integrated Heat
Sink) up. Locate Pin1 and the two ori­entation key notches.
orientation key notch
Pin1
orientation key notch
1366-Pin CPU
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
Pin1
ASRock X58 Extreme3 Motherboard
alignment key
alignment key
1366-Pin Socket
Page 15
Step 3-3. Carefully place the CPU into the socket
by using a purely vertical motion.
Step 3-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
2.22.2
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
2.2
Installation of CPU Fan and Heatsink
2.22.2
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
For proper installation, plea se kindly refer to the instruction ma nuals of your CPU fan a nd heatsink.
Below is an example to illustrate the installation of the heatsink for 1366-Pin CPU. Step 1. Apply thermal interface material onto center of
IHS on the socket surface.
Step 2. Place the heatsink onto the socket. Ensure fan
cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_F AN1, see page 2, No. 2).
Step 3. Align fasteners with the motherboard
throughholes.
Step 4. Rotate the fastener clockwise, then press down
on fastener caps with thumb to install and lock. Repeat with remaining fa steners.
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
EnglishEnglish
EnglishEnglish
et
Step 5. Connect fan header with the CPU fa n connector
on the motherboard.
Step 6. Secure excess cable with tie-wrap to en sure
cable does not interfere with fan operation or contact other components.
1515
15
ASRock X58 Extreme3 Motherboard
1515
English
Page 16
English
EnglishEnglish
EnglishEnglish
2.3 Installation of Memor2.3 Installation of Memor
2.3 Installation of Memor
2.3 Installation of Memor2.3 Installation of Memor
This motherboard provides six 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Triple Channel Memory Technology . For triple cha nnel configuration, you always need to install identical (the same bra nd, speed, size a nd chi p-type) DDR3 DIMM pair in the slots of the same color. In other words, you have to install identi- cal DDR3 DIMM pair in Tri ple Channel (DD R3_A1, DDR3_B1 and DD R3_C1; White slots; see p.2 No.7), or identical DDR3 DIMM pair in Triple Channel (DDR3_A2, DDR3_B2 and DDR3_C2; Blue slots; see p.2 No.11), so that Triple Channel Memory Technology can be activated. This motherboard also allows you to install six DDR3 DIMMs for triple channel configuration, and please install iden-
tical DDR3 DIMMs in all six slots.
Recommended Memory Configurations
DDR3_A2 DDR3_A1 DD R3_B2 DDR3_B1 DD R3_C2 DDR3_C1 (Blue) (White) (Blue) (White) (Blue) (White)
1 DIMM - Populated - - - ­ 2 DIMMs - Populated - Populated - ­ 3 DIMMs - Populated - Populated - Populated 4 DIMMs Populated Populated - Populated - Populated 5 DIMMs Populated Populated Populated Populated - Populated 6 DIMMs Populated Populated Populated Populated Populated Populated
1. Please install the memory module into the white slot (DDR3_A1, DDR3_B1 or DDR3_C1) for the first priority.
2. Due to Intel® CPU spec definition, the system will not boot if only one DIMM is installed into DDR3_A2, DDR3_B2 or DDR3_C2 slot.
3. Due to Intel® CPU spec definition, XMP DIMMs and DDR3 1600 are supported for one DIMM per channel only.
4. You may install varying memory sizes in Channel A, Channel B and Channel C. The system maps the total size of the lower-sized channel for the dual-channel or triple-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
5. It is not allowed to install a DDR or DDR2 memory module into DDR3 slot; otherwise, this motherboard and DIMM may be damaged.
y Modules (DIMM)y Modules (DIMM)
y Modules (DIMM)
y Modules (DIMM)y Modules (DIMM)
1616
16
1616
ASRock X58 Extreme3 Motherboard
Page 17
Installing a DIMMInstalling a DIMM
Installing a DIMM
Installing a DIMMInstalling a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining cli ps outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the bre a k
on the slot.
The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully
sna p back in place and the DIMM is properly seated.
ASRock X58 Extreme3 Motherboard
1717
17
1717
EnglishEnglish
EnglishEnglish
English
Page 18
English
EnglishEnglish
EnglishEnglish
2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)
2.4 Expansion Slots (PCI and PCI Express Slots)
2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)
There are 2 PCI slots and 4 PCI Express slots on this motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE slots:
PCIE2 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc. PCIE1 / PCIE3 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width graphics cards, or used to install PCI Express graphics cards to support CrossFireXTM or SLITM function. PCIE4 (PCIE x16 slot; White) is used for PCI Express x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.
1. In single VGA card mode, it is recommended to install a PCI Express x16 graphics card on PCIE1 slot.
2. In CrossFireXTM mode or SLITM mode, please install PCI Express x16 graphics cards on PCIE1 and PCIE3 slots. Therefore, both these two slots will work at x16 bandwidth.
3. Please connect a chassis fan to motherboard chassis fan connector (CHA_FAN1 or CHA_FAN2) when using multiple graphics cards for better thermal environment.
Installing an expansion cardInstalling an expansion card
Installing an expansion card
Installing an expansion cardInstalling an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in
a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.
1818
18
1818
ASRock X58 Extreme3 Motherboard
Page 19
TMTM
TM
2.5 SLI2.5 SLI
2.5 SLI
2.5 SLI2.5 SLI
This motherboard supports NVIDIA® SLITM and Quad SLITM (Scalable Link Interface) technology that allows you to install up to two identical PCI Express x16 graphics cards. Currently, NVIDIA® SLITM technology supports Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OS. NVIDIA® Quad SLITM technology support Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS only. Please follow the installation procedures in this section.
2.5.1 Graphics Card Setup2.5.1 Graphics Card Setup
2.5.1 Graphics Card Setup
2.5.1 Graphics Card Setup2.5.1 Graphics Card Setup
2.5.1.1 Installing Two SLI2.5.1.1 Installing Two SLI
2.5.1.1 Installing Two SLI
2.5.1.1 Installing Two SLI2.5.1.1 Installing Two SLI
Step 1. Install the identical SLITM-ready graphics cards that are NVIDIA® certified
TMTM
and Quad SLI and Quad SLI
and Quad SLI
and Quad SLI and Quad SLI
Requirements
1. For SLITM or Quad SLITM technology, you should have two identical SLITM-ready graphics cards that are NVIDIA® certified.
2. Make sure that your graphics card driver supports NVIDIA® SLI technology. Download the driver version 181.20 or later from NVIDIA website (www.nvidia.com).
3. Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. It is recommended to use NVIDIA® certified PSU. Please refer to NVIDIA® website for details.
because different types of graphics cards will not work together properly. (Even the GPU chips version shall be the same.) Insert one graphics card into PCIE1 slot and the other gra phics card to PCIE3 slot. M a ke sure that the cards are properly seated on the slots.
TM TM
TM
TM TM
Operation GuideOperation Guide
Operation Guide
Operation GuideOperation Guide
TMTM
TM
TMTM
-Ready Graphics Cards-Ready Graphics Cards
-Ready Graphics Cards
-Ready Graphics Cards-Ready Graphics Cards
TM
®
Step2. If required, connect the auxiliary power source to the PCI Express graphics
cards.
ASRock X58 Extreme3 Motherboard
1919
19
1919
EnglishEnglish
EnglishEnglish
English
Page 20
Step3. Align and insert ASRock SLI_Bridge_2S Card to the goldfingers on each
graphics card. Make sure ASRock SLI_Bridge_2S Card is firmly in place.
ASRock SLI_Bridge_2S Card
Step4. Connect a VGA cable or a DVI cable to the monitor connector or the DVI
connector of the graphics card that is inserted to PCIE1 slot.
2.5.2 Driver Installation and Setup2.5.2 Driver Installation and Setup
2.5.2 Driver Installation and Setup
2.5.2 Driver Installation and Setup2.5.2 Driver Installation and Setup
Install the graphics card drivers to your syste m. After that, you can enable the Multi­Graphics Processing U nit (GPU) fe ature in the N VIDIA® nView system tray utility. Ple a se follow the below procedures to enable the multi-GPU feature.
For Windows® XP / XP 64-bit OS: (For SLITM mode only)
A. Double-click NVIDIA Settings icon on your Windows® taskbar.
English
EnglishEnglish
EnglishEnglish
2020
20
2020
B. From the pop-up menu, select Set SLI and PhysX configuration. In Set PhysX GPU acceleration item, please select Enabled. In Select an SLI configuration item, please select Enable SLI. And click Apply.
ASRock X58 Extreme3 Motherboard
Page 21
C. Reboot your system. D. You can freely enjoy the benefit of SLITM feature.
For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: (For SLITM and Quad SLITM mode)
A. Click the Start icon on your Windows taskbar. B. From the pop-up menu, select All Programs, and then click NVIDIA Corporation. C. Select NVIDIA Control Panel tab. D. Select Control Panel tab.
E. From the pop-up menu, select Set SLI and PhysX configuration. In Set
PhysX GPU acceleration item, please select Enabled. In Select an SLI configuration item, please select Enable SLI. And click Apply.
F. Reboot your system. G. You can freely enjoy the benefit of SLITM or Quad SLITM feature.
ASRock X58 Extreme3 Motherboard
2121
21
2121
EnglishEnglish
EnglishEnglish
English
Page 22
TMTM
TM
2.62.6
CrossFireXCrossFireX
2.6
CrossFireX
2.62.6
CrossFireXCrossFireX GuideGuide
Guide
GuideGuide
This motherboard supports CrossFireXTM and Quad CrossFireXTM feature. CrossFireXTM technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units (GPU) in a single PC. Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism, CrossFireXTM enables the highest possible level of performance and image quality in any 3D application. Currently CrossFireXTM feature is supported with Windows® XP with Service Pack 2 / VistaTM / 7 OS. Quad CrossFireX check AMD website for ATITM CrossFireXTM driver updates.
2.6.1 Graphics Card Setup2.6.1 Graphics Card Setup
2.6.1 Graphics Card Setup
2.6.1 Graphics Card Setup2.6.1 Graphics Card Setup
2.6.1.1 Installing T2.6.1.1 Installing T
2.6.1.1 Installing T
2.6.1.1 Installing T2.6.1.1 Installing T
TM
1. If a customer incorrectly configures their system they will not see the performance benefits of CrossFireXTM. All three CrossFireXTM components, a CrossFireXTM Ready graphics card, a CrossFireXTM Ready motherboard and a CrossFireXTM Edition co-processor graphics card, must be installed correctly to benefit from the CrossFireXTM multi-GPU platform.
2. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both cards will operate as 12-pipe cards while in CrossFireXTM mode.
Cards Cards
Cards
Cards Cards
Different CrossFireXTM cards may require different methods to enable CrossFireX feature. In below procedures, we use Radeon HD 3870 as the example graphics card. For other CrossFireXTM cards that ATITM has released or will release in the future, please refer to ATITM graphics card manuals for detailed installation guide.
TMTM
and Quad CrossFireX and Quad CrossFireX
and Quad CrossFireX
and Quad CrossFireX and Quad CrossFireX
feature are supported with Windows® VistaTM / 7 OS only. Please
TMTM
TM
wo CrossFwo CrossF
wo CrossF
wo CrossFwo CrossF
ireXireX
ireX
ireXireX
TMTM
-R-R
-R
-R-R
TMTM
TM
TMTM
Operation Operation
Operation
Operation Operation
eady Graphicseady Graphics
eady Graphics
eady Graphicseady Graphics
TM
English
EnglishEnglish
EnglishEnglish
2222
22
2222
Step 1. Insert one Radeon graphics card into PCIE1 slot and the other Radeon
graphics card to PCIE3 slot. Make sure that the cards are properly seated on the slots.
ASRock X58 Extreme3 Motherboard
Page 23
Step 2. Connect two Radeon graphics cards by installing CrossFire Bridge on
CrossFire Bridge Interconnects on the top of Radeon graphics cards. (CrossFire Bridge is provided with the graphics card you purchase, not bundled with this motherboard. Please refer to your graphics card vendor for details.)
CrossFire Bridge
or
Step 3. Connect the DVI monitor cable to the DVI connector on the Radeon graphics
card on PCIE1 slot. (You may use the DVI to D-Sub adapter to convert the DVI connector to D-Sub interface, and then connect the D-Sub monitor cable to the DVI to D-Sub adapter.)
ASRock X58 Extreme3 Motherboard
2323
23
2323
EnglishEnglish
EnglishEnglish
English
Page 24
2.6.2 Driver Installation and Setup2.6.2 Driver Installation and Setup
2.6.2 Driver Installation and Setup
2.6.2 Driver Installation and Setup2.6.2 Driver Installation and Setup
Step 1. Power on your computer and boot into OS. Step 2. Remove the A TITM driver if you have any VGA driver in stalled in your system.
The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation. Please check AMD website for ATITM driver updates.
Step 3. Install the required drivers to your system.
For Windows® XP OS:
A. ATITM recommends Windows® XP Service Pack 2 or higher to be installed (If you have Windows® XP Service Pack 2 or higher installed
in your system, there is no need to download it again): http://www.microsoft.com/windowsxp/sp2/default.mspx B. You must have Microsoft .NET Framework installed prior to
downloading and installing the CATALYST Control Center . Please
check Microsoft website for details.
For Windows® 7 / VistaTM OS:
Install the CA TALYST Control Center. Please che ck AMD website for details.
Step 4. Restart your computer. Step 5. Install the VGA card drivers to your system, and restart your computer.
Then you will find “A TI Catalyst Control Center” on your Windows® taskbar.
(Driver Version: 8-12_vista32_dd_ccc_wdm_enu_72275.exe)
English
EnglishEnglish
EnglishEnglish
2424
24
2424
ATI Catalyst Control Center
Step 6. Double-click “ATI Catalyst Control Center”. Click “View”, select
“CrossFireXTM”, and then check the item “Enable CrossFireXTM”. Select the
option according to the total GPU number on the Radeon graphics cards.
Click “Apply”.
ASRock X58 Extreme3 Motherboard
Page 25
Although you have selected the option “Enable CrossFireTM”, the CrossFireX function may not work actually. Your computer will automatically reboot. After restarting your computer, please confirm whether the option “Enable CrossFireTM” in “ATI Catalyst Control Center” is selected or not; if not, please select it again, and then you are able to enjoy the benefit of CrossFireX feature.
TM
TM
Step 7. You can freely enjoy the benefit of CrossFireXTM or Quad CrossFireX
feature.
* CrossFireXTM appearing here is a registered trademark of ATITM Technologies Inc., and is used only for identification or explanation and to the owners’ benefit, without intent to infringe. * For further information of ATITM CrossFireXTM technology, please check AMD website for updates and details.
TM
ASRock X58 Extreme3 Motherboard
2525
25
2525
EnglishEnglish
EnglishEnglish
English
Page 26
2.7 Surround Display Feature2.7 Surround Display Feature
2.7 Surround Display Feature
2.7 Surround Display Feature2.7 Surround Display Feature
This motherboard supports Surround Display upgrade. With the external add-on PCI Express V GA cards, you can easily enjoy the benefits of Surround Display feature. For the detailed instruction, plea se refer to the document at the f ollowing path in the Support CD:
..\ Surround Display Information
2.8 Jumpers Setup2.8 Jumpers Setup
2.8 Jumpers Setup
2.8 Jumpers Setup2.8 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper Setting Description
PS2_USB_PWR1 Short pin2, pin3 to enable
(see p.2 No. 1) +5VSB (standby) for PS/2
Note: To select +5VSB, it requires 2 Amp and higher sta ndby current provided by power
supply.
Clear CMOS Jumper
(CLRCMOS1) (see p.2 No. 15)
Clear CMOSDefault
Short Open
or USB wake up events.
English
EnglishEnglish
EnglishEnglish
2626
26
2626
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn of f the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper ca p to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However , please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear­CMOS action.
If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.
ASRock X58 Extreme3 Motherboard
Page 27
2.9 Onboard Headers and Connectors2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors
2.9 Onboard Headers and Connectors2.9 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
FDD connector
(33-pin FLOPPY1) (see p.2 No. 31)
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.2 No. 14)
connect the blue end
to the motherboard
connect the black end to the IDE devices
80-conductor ATA 66/100/133 cable
Note: Please refer to th e i n struction of your IDE device vendor for the details.
Serial ATAII Connectors These six Serial ATAII (SATAII)
(SAT AII_1_2: connectors support SATA data see p.2, No. 16) cables for internal storage (SAT AII_3_4: devices. The current SATAII see p.2, No. 17) interface allows up to 3.0 Gb/s (SAT AII_5_6: data transfer rate. see p.2, No. 18)
SAT AII_5_6 SA T AII_3_4 SA T AII_1_2
Serial ATA3 Connectors These two Serial ATA3
(SAT A3_1: see p.2, No. 13) (SATA3) connectors support (SAT A3_2: see p.2, No. 12) SATA data cables for internal
SAT A3_2
SAT A3_1
storage devices. The current SATA3 interface allows up to
6.0 Gb/s data transfer rate.
ASRock X58 Extreme3 Motherboard
2727
27
2727
EnglishEnglish
EnglishEnglish
English
Page 28
Serial A TA (SA TA) Either end of the SAT A data cable Data Cable can be connected to the SATA /
(Optional) SATAII hard disk or the SATAII
connector on this motherboard.
Serial ATA (SATA) Please connect the black end of Power Cable SATA power cable to the power
(Optional) connector on each drive. Then
connect to the SAT A
HDD power connector
connect to the power supply
connect the white end of SATA power cable to the power connector of the power supply.
USB 2.0 Headers Besides five default USB 2.0
(9-pin USB6_7) ports on the I/O panel, there are (see p.2 No. 25) two USB 2.0 headers on this
motherboard. Each USB 2.0 header can support two USB
2.0 ports.
(9-pin USB8_9) (see p.2 No. 10)
TPM Header This connector supports a
(19-pin TPM1) Trusted Platform Module (TPM) (see p.2 No. 29) system, which can securely
store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.
English
EnglishEnglish
EnglishEnglish
2828
28
2828
Infrared Module Header This header supports an optional
(5-pin IR1) wireless transmitting and (see p.2 No. 33) receiving infrared module.
ASRock X58 Extreme3 Motherboard
Page 29
Chassis Intrusion Header This motherboard supports
(2-pin CI1) CASE OPEN detection feature (see p.2 No. 35) that detects if the chassis cover
has been removed. This feature requires a chassis with chassis intrusion detection design.
Internal Audio Connectors This connector allows you
(4-pin CD1) to receive stereo audio input (CD1: see p.2 No. 43) from sound sources such as
CD1
a CD-ROM, D VD-ROM, TV tuner card, or MPEG card.
Front Panel Audio Header This is an interface for front
(9-pin HD_AUDIO1) panel audio cable that allows (see p.2 No. 44) convenient connection and
control of audio devices.
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel. E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from
[Auto] to [Enabled].
System Panel Header This header accommodates
(9-pin PANEL1) several system front panel (see p.2 No. 9) functions.
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1) speaker to this header. (see p.2 No. 21)
ASRock X58 Extreme3 Motherboard
2929
29
2929
EnglishEnglish
EnglishEnglish
English
Page 30
Power LED Header Please connect the chassis
(3-pin PLED1) power LED to this header to (see p.2 No. 20) indicate system power status.
The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).
Chassis, NB and Power Fan Connectors Please connect the fan cables
(4-pin CHA_FAN1) to the fan connectors and (see p.2 No. 28) match the black wire to the
ground pin.
(3-pin CHA_FAN2) (see p.2 No. 6)
(3-pin NB_FAN1) (see p.2 No. 42)
(3-pin PWR_FAN1) (see p.2 No. 5)
English
EnglishEnglish
EnglishEnglish
3030
30
3030
CPU Fan Connector Please connect a CPU fan cable
(4-pin CPU_FAN1) to this connector and match (see p.2 No. 2) the black wire to the ground pin.
4 3 2 1
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Connector Please connect an ATX power
(24-pin ATXPW R1) supply to this connector. (see p.2, No. 8)
12 124
13
ASRock X58 Extreme3 Motherboard
Page 31
Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.
12
24
20-Pin A TX Power Supply Installation
ATX 12V Power Connector Please connect an ATX 12V
(8-pin A TX12V1) power supply to this connector. (see p.2 No. 3)
Though this motherboard provides 8-pin ATX 12V power connector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 5.
8 5
4 1
4-Pin ATX 12V Power Supply Installation
1
8 5
4 1
13
IEEE 1394 Header Besides one default IEEE 1394
(9-pin FRONT_1394) port on the I/O panel, there is one (see p.2 No. 27) IEEE 1394 header
(FRONT_1394) on this motherboard. This IEEE 1394 header cansupport one IEEE 1394 port.
Serial port Header This COM1 header supports a
(9-pin COM1) serial port module. (see p.2 No.30)
HDMI_SPDIF Header HDMI_SPDIF header, providing
(3-pin HDMI_SPDIF1) SPDIF audio output to HDMI V GA (see p.2 No. 32) card, allows the system to
connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
ASRock X58 Extreme3 Motherboard
3131
31
3131
EnglishEnglish
EnglishEnglish
English
Page 32
HDMI_SPDIF Cable Please connect the black end (A)
(Optional) of HDMI_SPDIF cable to the
C
B
A
HDMI_SPDIF header on the motherboard. Then connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF connector of HDMI VGA card.
A. black end B. white end (2-pin) C. white end (3-pin)
2.10 Smart Switches2.10 Smart Switches
2.10 Smart Switches
2.10 Smart Switches2.10 Smart Switches
This motherboard has three smart switches: power switch, reset switch and clear CMOS switch, allowing users to quickly turn on/off or reset the system or clear the CMOS values.
Power Switch Power Switch is a smart switch,
(PWRBTN) allowing users to quickly turn (see p.2 No. 24) on/off the system.
Reset Switch Reset Switch is a smart switch,
(RSTBTN) allowing users to quickly reset (see p.2 No. 23) the system.
English
EnglishEnglish
EnglishEnglish
3232
32
3232
Clear CMOS Switch Clear CMOS Switch is a smart
(CLRCBTN) switch, allowing users to quickly (see p.2 No. 17) clear the CMOS values
You are not allowed to use Clear CMOS switch function if you set up the system password. If you want to clear the CMOS values, please clean your system password in advance or refer to page 26 “Clear CMOS jumper” description instead.
ASRock X58 Extreme3 Motherboard
Page 33
2.11 Dr. Debug2.11 Dr. Debug
2.11 Dr. Debug
2.11 Dr. Debug2.11 Dr. Debug
Dr. Debug is used to provide code information, which makes troubleshooting even easier. Please see the diagrams below for reading the Dr. Debug codes.
The Bootblock initialization code sets up the chipset, memory and other components before system memory is available. The following table describes the type of checkpoints that may occur during the bootblock initialization portion of the BIOS:
Checkpoint Description
Before D1 Early chipset initialization is done. Early super I/O initialization is done
including RTC and keyboard controller. NMI is disabled.
D1 Perform keyboard controller BAT test. Check if waking up from power
management suspend state. Save power-on CPUID value in scratch CMOS.
D0 Go to flat mode with 4GB limit and GA20 enabled. Verify the bootblock
checksum.
D2 Disable CACHE before memory detection. Execute full memory sizing
module. Verify that flat mode is enabled.
D3 If memory sizing module not executed, start memory refresh and do
memory sizing in Bootblock code. Do additional chipset initialization.
Re-enable CACHE. Verify that flat mode is enabled. D4 Test base 512KB memory. Adjust policies and cache first 8MB. Set stack. D5 Bootblock code is copied from ROM to lower system memory and control
is given to it. BIOS now executes out of RAM. D6 Both key sequence and OEM specific method is checked to determine if
BIOS recovery is forced. Main BIOS checksum is tested. If BIOS recovery
is necessary, control flows to checkpoint E0. D7 Restore CPUID value back into register. The Bootblock-Runtime interface
module is moved to system memory and control is given to it. Determine
whether to execute serial flash. D8 The Runtime module is uncompressed into memory. CPUID information is
stored in memory. D9 Store the Uncompressed pointer for future use in PMM. Copying Main BIOS
into memory. Leaves all RAM below 1MB Read-Write including E000 and
F000 shadow area s but closing SMRAM. DA Restore CPUID value back into register. Give control to BIOS POST
(ExecutePOSTKernel).
ASRock X58 Extreme3 Motherboard
3333
33
3333
EnglishEnglish
EnglishEnglish
English
Page 34
English
EnglishEnglish
EnglishEnglish
The POST code checkpoints are the largest set of checkpoints during the BIOS pre-boot process. The following table describes the type of checkpoints that may occur during the POST portion of the BIOS:
Checkpoint Description
03 Disable NMI, Parity, video for EGA, and DMA controllers.
Initialize BIOS, POST, Runtime data area. Also initialize BIOS modules on POST entry and GPNV area. Initialized CMOS as mentioned in the Kernel V ari able “wCMOSFlags.”
04 Check CMOS diagnostic byte to determine if battery power is OK and
CMOS checksum is OK. Verify CMOS checksum manually by reading storage area. If the CMOS checksum is bad, update CMOS with power-on default values and clear passwords. Initialize status register A. Initializes data variables that are based on CMOS setup questions. Initializes both the 8259 compatible PICs in the system
05 Initializes the interrupt controlling hardware (generally PIC) and interrupt
vector table.
06 Do R/W test to CH-2 count reg. Initialize CH-0 as system timer. Install the
POSTINT1Ch handler. Enable IRQ-0 in PIC for system timer interrupt. Traps INT1Ch vector to “POSTINT1ChHandlerBlock.”
08 Initializes the CPU. The BAT test is being done on KBC. Program the
keyboard controller command byte is being done after Auto detection of
KB/MS using AMI KB-5. C0 Early CPU Init Start — Disable Cache - Init Local APIC C1 Set up boot strap proccessor Information C2 Set up boot strap proccessor for POST C5 Enumerate and set up application proccessors C6 Re-enable cache for boot strap proccessor C7 Early CPU Init Exit 0A Initializes the 8042 compatible Key Board Controller. 0B Detects the presence of PS/2 mouse. 0C Detects the presence of Keyboard in KBC port. 0E Testing and initialization of different Input Devices. Also, update the Kernel
Variables. Traps the INT09h vector, so that the POST INT09h handler gets
control for IRQ1. Uncompress all available language, BIOS logo, and Silent
logo modules. 13 Early POST initialization of chipset registers. 24 Uncompress and initialize any platform specific BIOS modules. 30 Initialize System Management Interrupt. 2A Initializes different devices through DIM.
See DIM Code Checkpoints section of document for more information. 2C Initializes different devices. Detects and initializes the video adapter
installed in the system that have optional ROMs. 2E Initializes all the output devices. 31 Allocate memory for ADM module and uncompress it. Give control to ADM
module for initialization. Initialize language and font modules for ADM.
Activate ADM module.
3434
34
3434
ASRock X58 Extreme3 Motherboard
Page 35
33 Initializes the silent boot module. Set the window for displaying text
information.
37 Displaying sign-on message, CPU information, setup key message, and
any OEM specific information. 38 Initializes different devices through DIM. 39 Initializes DMAC-1 & DMAC-2. 3A Initialize RTC date/time. 3B Test for total memory installed in the system. Also, Check for DEL or ESC
keys to limit memory test. Display total memory in the system. 3C Mid POST initialization of chipset registers. 40 Detect different devices (Parallel ports, serial ports, and coprocessor in
CPU, etc.) successfully installed in the system and update the BDA,
EBDA, etc. 50 Programming the memory hole or any kind of implementation that needs an
adjustment in system RAM size if needed. 52 Updates CMOS memory size from memory found in memory test.
Allocates memory for Extended BIOS Data Area from base memory. 60 Initializes NUM-LOCK status and programs the KBD typematic rate. 75 Initialize Int-13 and prepare for IPL detection. 78 Initializes IPL devices controlled by BIOS and option ROMs. 7A Initializes remaining option ROMs. 7C Generate and write contents of ESCD in NVRam. 84 Log errors encountered during POST. 85 Display errors to the user and gets the user response for error. 87 Execute BIOS setup if needed / requested. 8C Late POST initialization of chipset registers. 8D Build ACPI tables (if ACPI is supported) 8E Program the peripheral parameters. Enable/Disable NMI as selected 90 Late POST initialization of system management interrupt. A0 Check boot password if installed. A1 Clean-up work needed before booting to OS. A2 Takes care of runtime image preparation for different BIOS modules. Fill
the free area in F000h segment with 0FFh. Initializes the Microsoft IRQ
Routing Table. Prepares the runtime language module. Disables the system
configuration display if needed. A4 Initialize runtime language module. A7 Displays the system configuration screen if enabled. Initialize the CPU’s
before boot, which includes the programming of the MTRR’s. A8 Prepare CPU for OS boot including final MTRR values. A9 Wait for user input at config display if needed. AA Uninstall POST INT1Ch vector and INT09h vector. Deinitializes the ADM
module. AB Prepare BBS for Int 19 boot. AC End of POST initialization of chipset registers. B1 Save system context for ACPI. 00 Passes control to OS Loader (typically INT19h).
EnglishEnglish
EnglishEnglish
English
ASRock X58 Extreme3 Motherboard
3535
35
3535
Page 36
2.122.12
Driver Installation Guide Driver Installation Guide
2.12
Driver Installation Guide
2.122.12
Driver Installation Guide Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.
English
EnglishEnglish
EnglishEnglish
2.132.13
Installing WindowsInstalling Windows
2.13
Installing Windows
2.132.13
Installing WindowsInstalling Windows 64-bit / XP / XP 64-bit With RAID Functions64-bit / XP / XP 64-bit With RAID Functions
64-bit / XP / XP 64-bit With RAID Functions
64-bit / XP / XP 64-bit With RAID Functions64-bit / XP / XP 64-bit With RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit on your SATA / SATAII HDDs with RAID functions, please refer to the document at the following path in the Support CD for detailed procedures:
..\ RAID Installation Guide
2.142.14
Installing WindowsInstalling Windows
2.14
Installing Windows
2.142.14
Installing WindowsInstalling Windows 64-bit / XP / XP 64-bit Without RAID Functions64-bit / XP / XP 64-bit Without RAID Functions
64-bit / XP / XP 64-bit Without RAID Functions
64-bit / XP / XP 64-bit Without RAID Functions64-bit / XP / XP 64-bit Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OS on your SATA / SAT AII HDDs without RAID functions, please follow below procedures according to the OS you install.
2.14.1 Installing Windows2.14.1 Installing Windows
2.14.1 Installing Windows
2.14.1 Installing Windows2.14.1 Installing Windows Functions Functions
Functions
Functions Functions
If you want to install Windows® XP / XP 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs and eSATA3 devices without NCQ function
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen Storage Configuration. B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure SATAII as”, ple ase set the option to [IDE].
STEP 2: Install Windows® XP / XP 64-bit OS on your system.
®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
®
XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID
XP / XP 64-bit Without RAID
XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID
TM TM
TM
TM TM
TM TM
TM
TM TM
/ Vista/ Vista
/ Vista
/ Vista/ Vista
/ Vista/ Vista
/ Vista
/ Vista/ Vista
TMTM
TM
TMTM
TMTM
TM
TMTM
3636
36
3636
ASRock X58 Extreme3 Motherboard
Page 37
2.14.2 Installing Windows2.14.2 Installing Windows
2.14.2 Installing Windows
2.14.2 Installing Windows2.14.2 Installing Windows 64-bit Without RAID Functions 64-bit Without RAID Functions
64-bit Without RAID Functions
64-bit Without RAID Functions 64-bit Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs and eSATA3 devices without NCQ function
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen Storage Configuration. B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure SATAII as”, please set the option to [IDE].
STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your
system.
Using SATA / SATAII HDDs and eSATA3 devices with NCQ function
STEP 1: Set Up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen Storage Configuration. B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure SATAII as”, please set the option to [AHCI].
STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your
system.
2.152.15
Untied Overclocking TUntied Overclocking T
2.15
Untied Overclocking T
2.152.15
Untied Overclocking TUntied Overclocking T
This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, plea se enter “Overclock Mode” option of BIOS setup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment.
®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
echnologyechnology
echnology
echnologyechnology
TM TM
TM
TM TM
/ Vista/ Vista
/ Vista
/ Vista/ Vista
TMTM
TM
TMTM
Please refer to the warning on page 8 for the possible overclocking risk before you apply Untied Overclocking Technology.
ASRock X58 Extreme3 Motherboard
3737
37
3737
EnglishEnglish
EnglishEnglish
English
Page 38
3. BIOS Information3. BIOS Information
3. BIOS Information
3. BIOS Information3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.
English
EnglishEnglish
EnglishEnglish
4. Sof4. Sof
4. Sof
4. Sof4. Sof
This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / VistaTM / Vista motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD­ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double­click on the file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
tware Supportware Suppor
tware Suppor
tware Supportware Suppor
TM
64-bit / XP / XP 64-bit. The Support CD that came with the
t CD informationt CD information
t CD information
t CD informationt CD information
3838
38
3838
ASRock X58 Extreme3 Motherboard
Page 39
1. Einführung1. Einführung
1. Einführung
1. Einführung1. Einführung
Wir danken Ihnen für den Kauf des ASRock X58 Extreme3 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robuste s Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installa­tion ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.
Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite: www.asrock.com/support/index.asp
1.1 Kartoninhalt1.1 Kartoninhalt
1.1 Kartoninhalt
1.1 Kartoninhalt1.1 Kartoninhalt
ASRock X58 Extreme3 Motherboard
(ATX-Formfa ktor: 30.5 cm x 24.4 cm; 12.0 Zoll x 9.6 Zoll) ASRock X58 Extreme3 Schnellinstallationsanleitung ASRock X58 Extreme3 Support-CD Ein 80-adriges Ultra-A T A 66/100/133 IDE-Flachba ndka bel Ein Flachba ndkabel für e in 3,5-Zoll-Diskettenlaufwerk Vier Serial ATA (SATA) -Datenkabel (optional) Zwei Serial ATA (SAT A) -Festplattenstromka bel (optional) Ein I/O Shield Ein ASRock SLI_Bridge_2S-Karte
ASRock X58 Extreme3 Motherboard
3939
39
3939
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 40
Deutsch
DeutschDeutsch
DeutschDeutsch
1.21.2
SpezifikationenSpezifikationen
1.2
Spezifikationen
1.21.2
SpezifikationenSpezifikationen
Plattform - ATX-Formfaktor: 30.5 cm x 24.4 cm; 12.0 Zoll x 9.6 Zoll
- Alle Feste Konden satordesign (100% in Japan gefertigte, erstklassige leitfähige Polymer-Konden satoren)
CPU - Intel®-Sockel 1366 CoreTM i7-Prozessor Extreme Edition /
CoreTM i7-Prozessor unterstützt Intel® Dyna mic Speed­ T echnologie
- System-Bus bis 6400 MT/s; Intel® QuickPath-Interconnect
- Erweitertes V8-Stromphasendesign
- Unterstützt Hyper-Threading-Technologie (siehe VORSICHT 1)
- Unterstützt Untied-Übertaktungstechnologie (siehe VORSICHT 2)
- Unterstützt EM64T -CPU
Chipsatz - Northbridge: Intel® X58
- Southbridge: Intel® ICH10R
Speicher - Triple-Channel-DDR3-Speichertechnologie
(siehe VORSICHT 3)
- 6 x Steckplätze für DDR3
- Unterstützt DDR3 2000(OC)/1866(OC)/1600(OC)/1333(OC)/ 1066 non-ECC, ungepufferter Speicher
- Unterstützt DDR3 ECC, ungepufferter Speicher mit Intel Workstation 1S Xeon®-Prozessoren der 3500-Serie
- Max. Kapazität de s Systemspeichers: 24GB (siehe VORSICHT 4)
- Unterstützt Intel® Extreme Memory Profile (XMP) Erweiterungs- - 2 x PCI Express 2.0 x16-Steckplätze (blau im x16-Modus) steckplätze - 1 x PCI Express x16-Steckplätze (Weiß im x4-Modus)
(Doppelbreiter Steckplatzabstand zwischen jedem einzelnen PCI-E-Steckplatz)
- 1 x PCI Express x1-Steckplätze
- 2 x PCI -Steckplätze
- Unterstützt ATITM CrossFireXTM und Quad CrossFireX
- Unterstützt NVIDIA® SLITM und Quad SLI Audio - 7.1 CH HD Audio mit dem Inhalt Schutz
- DAC mit 110dB Aussteuerungsbereich
(VIA® VT2020 Audio Codec)
- Premium Blu-ray-Audio-Unterstützung LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
TM
®
TM
4040
40
4040
ASRock X58 Extreme3 Motherboard
Page 41
- Realtek RTL81 11DL
- Unterstützt Wake-On-LAN E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss
- 1 x Koaxial-SPDIF-Ausgang
- 1 x optischer SPDIF-Ausgang
- 5 x Standard-USB 2.0-Anschlüsse
- 1 x eSATAIII/USB 2.0-Anschluss mit Stromversorgung
- 2 x Standard-USB 3.0-Anschlüsse
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
- 1 x IEEE 1394 Port
- 1 x CMOS löschen-Schalter
- HD Audiobuchse: Lautsprecher seitlich / Lautsprecher hinten
/ Mitte/Bass / Audioeingang/ Lautsprecher vorne / Mikrofon (siehe VORSICHT 5)
SATA3 - 2 x SATA 3-Anschlüsse (6,0 Gb/s) durch Marvell SE9128;
unterstützt Hardware-RAID- (RAID 0 und RAID 1), NCQ-, AHCI­ und „Hot Plug“ (Hot-Plugging)-Funktionen (SATA3_2­ Anschluss wird mit dem eSATA 3-Port geteilt)
USB 3.0 - 2 x USB 3.0-Ports durch NEC UPD720200; unterstützt
USB 1.0/2.0/3.0 mit bis zu 5 Gb/s
Anschlüsse - 6 x Serial ATAII 3,0 GB/s-Anschlüsse, unterstützen RAID-
(RAID 0, RAID 1, RAID 10, RAID 5 und Intel Matrix Storage), NCQ, AHCI und “Hot Plug” Funktionen
- 2 x SATA3 6,0 GB/s-Anschlüsse
- 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)
- 1 x FDD-Anschlüsse
- 1 x Infrarot-Modul-Header
- 1 x COM-Anschluss-Header
- 1 x HDMI_SPDIF-Anschluss
- 1 x IEEE 1394-Anschluss
- 1 x TPM-Stiftleiste
- 1 x Verteiler für Gehäuseeindringversuche
- 1 x Betriebs-LED-Header
- CPU/Gehäuse/NB/Stromlüfter-Anschluss
- 24-pin ATX-Netz-Header
- 8-pin anschluss für 12V-ATX-Netzteil
- Interne Audio-Anschlüsse
- Anschluss für Audio auf der Gehäusevorderseite
- 2 x USB 2.0-Anschlüsse (Unterstützung 4
zusätzlicher USB 2.0-Anschlüsse) (siehe VORSICHT 6)
ASRock X58 Extreme3 Motherboard
4141
41
4141
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 42
Deutsch
DeutschDeutsch
DeutschDeutsch
4242
42
4242
- 1 x Dr. Debug (Debug-LED mit 7 Segmenten)
Schnellschalter - 1 x CMOS löschen-Schalter mit LED
- 1 x Netzschalter mit LED
- 1 x Rücksetzschalter (Reset) mit LED
BIOS - 8Mb AMI BIOS
- AMI legal BIOS mit Unterstützung für “Plug and Play”
- ACPI 1.1-Weckfunktionen
- JumperFree-Übertaktungstechnologie
- SMBIOS 2.3.1
- Zentraleinheit, VCCM, IOH, ICH, VTT, IOH/ICH PCIE, CPU PLL, IOH CSI, VCORE Stromspannung Multianpassung
- Unterstützt I. O. T. (Intelligente Übertakten Technologie)
Support-CD - Treiber, Dienstprogramme, Antivirussoftware
(Probeversion), ASRock-Software-Suite (CyberLink DVD Suite und Creative Sound Blaster X-Fi MB) (OEM- und Testversion)
Einzigartige - ASRock OC Tuner (siehe VORSICHT 7) Eigenschaft - Intelligent Energy Saver (Intelligente Energiesparfunktion)
(siehe VORSICHT 8)
- Sofortstart
- ASRock Instant Flash (siehe VORSICHT 9)
- ASRock OC DNA (siehe VORSICHT 10)
- Hybrid Booster:
- Schrittloser CPU-Frequenz-Kontrolle (siehe VORSICHT 11)
- ASRock U-COP (siehe VORSICHT 12)
- Boot Failure Guard (B.F.G. – Systemstartfehlerschutz)
- Gute Nacht-LED
Hardware Monitor - Überwachung der CPU-Temperatur
- Motherboardtemperaturerkennung
- Drehzahlmessung für CPU/Gehäuse/NB/Stromlüfter
- CPU-Lüftergeräuschdämpfung
- Mehrstufige Geschwindigkeitsteuerung für CPU-/ Gehäuselüfter
- GEHÄUSE OFFEN-Erkennung
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
Betriebssysteme - Unterstützt Microsoft® Windows® 7 / 7 64-Bit / VistaTM /
Zertifizierungen - FCC, CE, WHQL
TM
Vista
64-Bit / XP / XP 64-Bit
- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich) (siehe VORSICHT 13)
ASRock X58 Extreme3 Motherboard
Page 43
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com
WARNUNG
Beachten Sie bitte, dass Overclocking, einschließlich der Einstellung im BIOS, Anwenden der Untied Overclocking-Technologie oder Verwenden von Overclocking-Werkzeugen von Dritten, mit einem gewissen Risiko behaftet ist. Overclocking kann sich nachteilig auf die Stabilität Ihres Systems auswirken oder sogar Komponenten und Geräte Ihres Systems beschädigen. Es geschieht dann auf eigene Gefahr und auf Ihre Kosten. Wir übernehmen keine Verantwortung für mögliche Schäden, die aufgrund von Overclocking verursacht wurden.
VORSICHT!
1. Die Einstellung der “Hyper-Threading Technology”, finden Sie auf Seite 62 des auf der Support-CD enthaltenen Benutzerhandbuches beschrieben.
2. Dieses Motherboard unterstützt die Untied-Übertaktungstechnologie. Unter “Entkoppelte Übertaktungstechnologie” auf Seite 37 finden Sie detaillierte Informationen.
3. Dieses Motherboard unterstützt Triple-Kanal-Speichertechnologie. Vor Implementierung der Triple-Kanal-Speichertechnologie müssen Sie die Installationsanleitung für die Speichermodule auf Seite 49 zwecks richtiger Installation gelesen haben.
4. Durch Betriebssystem-Einschränkungen kann die tatsächliche Speichergröße weniger als 4 GB betragen, da unter Windows® 7 / Vista™ / XP etwas Speicher zur Nutzung durch das System reserviert wird. Unter Windows® OS mit 64-Bit-CPU besteht diese Einschränkung nicht.
5. Der Mikrofoneingang dieses Motherboards unterstützt Stereo- und Mono­Modi. Der Audioausgang dieses Motherboards unterstützt 2-Kanal-, 4­Kanal-, 6-Kanal- und 8-Kanal-Modi. Stellen Sie die richtige Verbindung anhand der Tabelle auf Seite 3 her.
6. Das Power Management für USB 2.0 arbeitet unter Microsoft® Windows 7 64-Bit / 7 / VistaTM 64-Bit / VistaTM / XP 64-Bit / XP SP1 oder SP2 einwandfrei.
7. Es ist ein benutzerfreundlicher ASRock Übertaktenswerkzeug, das erlaubt, dass Sie Ihr System durch den Hardware-Monitor Funktion zu überblicken und Ihre Hardware-Geräte übertakten, um die beste Systemleistung unter der Windows® Umgebung zu erreichen. Besuchen Sie bitte unsere Website für die Operationsverfahren von ASRock OC Tuner . ASRock-Website: http://www.asrock.com
8. Mit einem fortschrittlichen, eigenständigen Hard- und Softwaredesign nutzt der Intelligent Energy Saver eine revolutionäre Technologie, die bisher unerreichte Energieeinsparungen ermöglicht. Mit anderen Worten: Sie verbrauchen besonders wenig Energie und erreichen einen hohen Wirkungsgrad, ohne dass dies zu Lasten der Rechenleistung geht. Auf unseren Internetseiten finden Sie einige Erläuterungen zur Funktionsweise des Intelligent Energy Saver. ASRock-Website: http://www.asrock.com
ASRock X58 Extreme3 Motherboard
®
DeutschDeutsch
DeutschDeutsch
Deutsch
4343
43
4343
Page 44
Deutsch
DeutschDeutsch
DeutschDeutsch
4444
44
4444
9. ASRock Instant Flash ist ein im Flash-ROM eingebettetes BIOS-Flash-
Programm. Mithilfe dieses praktischen BIOS-Aktualisierungswerkzeugs können Sie das System-BIOS aktualisieren, ohne dafür zuerst Betriebssysteme wie MS-DOS oder Windows® aufrufen zu müssen. Mit diesem Progra mm bekommen Sie durch Drücken der <F6>-Taste während des POST-Vorgangs oder durch Drücken der <F2>-Taste im BIOS-Setup-Menü Zugang zu ASRock Instant Flash. Sie brauchen dieses Werkzeug einfach nur zu starten und die neue BIOS-Datei auf Ihrem USB-Flash-Laufwerk, Diskettenlaufwerk oder der Festplatte zu speichern, und schon können Sie Ihr BIOS mit nur wenigen Klickvorgängen ohne Bereitstellung einer zusätzlichen Diskette oder eines anderen komplizierten Flash-Programms aktualisieren. Achten Sie darauf, dass das USB-Flash-Laufwerk oder die Festplatte das Dateisystem FAT32/16/12 benutzen muss.
10. Allein der Name – OC DNA* – beschreibt es wörtlich, was die Software
zu leisten vermag. OC DNA ist ein von ASRock exklusiv entwickeltes Dienstprogramm, das Nutzern eine bequeme Möglichkeit bietet, Übertaktungseinstellungen aufzuzeichnen und sie Anderen mitzuteilen. Es hilft Ihnen, Ihre Übertaktungsaufzeichnung im Betriebssystem zu speichern und vereinfacht den komplizierten Aufzeichnungsvorgang von Übertaktungseinstellungen. Mit OC DNA können Sie Ihre Übertaktungseinstellungen als Profil abspeichern und Ihren Freunden zugänglich machen! Ihre Freunde können dann das Übertaktungsprofil auf ihren eigenen Systemen laden, um dieselben Übertaktungseinstellungen wie Sie zu erhalten! Beachten Sie bitte, dass das Übertaktungsprofil nur bei einem identischen Motherboard gemeinsam genutzt und funktionsfähig gemacht werden kann.
11 . Obwohl dieses Motherboard stufenlose Steuerung bietet, wird Over-
clocking nicht empfohlen. Frequenzen, die über den für den jeweiligen Prozessor vorgesehenen liegen, können das System instabil werden lassen oder die CPU beschädigen.
12. Die Combo-Kühleroption bietet die flexible Möglichkeit zur Aufnahme von
zwei verschiedenen CPU-Kühlertypen, Socket LGA 775 und LGA 1156. Beachten Sie bitte, dass nicht alle 775 CPU-Lüfter verwendet werden können.
13. EuP steht für Energy Using Product und kennzeichnet die Ökodesign-
Richtlinie, die von der Europäischen Gemeinschaft zur Festlegung des Energieverbrauchs von vollständigen Systemen in Kraft gesetzt wurde. Gemäß dieser Ökodesign-Richtlinie (EuP) muss der gesamte Netzstromverbrauch von vollständigen Systemen unter 1,00 Watt liegen, wenn sie ausgeschaltet sind. Um dem EuP-Standard zu entsprechen, sind ein EuP-fähiges Motherboard und eine EuP-fähige Stromversorgung erforderlich. Gemäß einer Empfehlung von Intel muss eine EuP-fähige Stromversorgung dem Standard entsprechen, was bedeutet, dass bei einem Stromverbrauch von 100 mA die 5-Volt-Standby-Energieeffizienz höher als 50% sein sollte. Für die Wahl einer EuP-fähigen Stromversorgung empfehlen wir Ihnen, weitere Details beim Hersteller der Stromversorgung abzufragen.
ASRock X58 Extreme3 Motherboard
Page 45
2. Installation2. Installation
2. Installation
2. Installation2. Installation
Sicherheitshinweise vor der MontageSicherheitshinweise vor der Montage
Sicherheitshinweise vor der Montage
Sicherheitshinweise vor der MontageSicherheitshinweise vor der Montage
Bitte nehmen Sie die folgende Sicherheitshinweise zur Kenntnis, bevor Sie das Motherboard einbauen oder Veränderungen an den Einstellungen vornehmen.
1. Trennen Sie das System vom Stromnetz, bevor Sie eine ystemkomponente berühren, da es sonst zu schweren Schäden a m Motherboard oder den sonstigen internen, bzw. externen omponenten kommen kann.
2. Um Schäden aufgrund von statischer Elektrizität zu vermeiden, das Motherboard NIEMALS auf einen Teppich o.ä.legen. Denken Sie außerem daran, immer ein geerdetes Armband zu tragen oder ein geerdetes Objekt aus Metall zu berühren, bevor Sie mit Systemkomponenten hantieren.
3. Halten Sie Komponenten immer an den Rändern und vermeiden Sie Berührungen mit den ICs.
4. Wenn Sie Komponenten ausbauen, legen Sie sie immer auf eine antistatische Unterlage, oder zurück in die Tüte, mit der die Komponente geliefert wurde.
5. Wenn Sie das Motherboard mit den Schrauben an dem Computergehäuse befestigen, überziehen Sie bitte die Schrauben nicht! Das Motherboard kann sonst beschädigt werden.
2.1 CPU Installation2.1 CPU Installation
2.1 CPU Installation
2.1 CPU Installation2.1 CPU Installation
Für die Installation des Intel 1366-Pin CPU führen Sie bitte die folgenden Schritte durch.
(Ladeplatte)
(Kontaktreihe)
1366-Pin Sockel Übersicht
Bevor Sie die 1366-Pin CPU in den Sockel sitzen, prüfen Sie bitte, ob die CPU-Oberfläche sauber ist und keine der Kontakte verbogen sind. Setzen Sie die CPU nicht mit Gewalt in den Sockel, dies kann die CPU schwer beschädigen.
ASRock X58 Extreme3 Motherboard
(Sockel)
4545
45
4545
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 46
Schritt 1. Öffnen Sie den Sockel:
Schritt 1-1. Öffnen Sie den Hebel, indem
Sie ihn nach unten drücken und aushaken.
Schritt 1-2. Drehen Sie den Ladehebel, bis
er in geöffneter Position steht, ca. 135 Grad.
Schritt 1-3. Drehen Sie die Ladeplatte, bis
sie in geöffneter Position steht, ca. 100 Grad.
Schritt 2. PnP-Kappe entfernen (Pick and Pla ce-Ka ppe).
1. Verwenden Sie beim Entfernen die Kappenlasche und vermeiden Sie ein Abreißen der PnP-Kappe.
2. Diese Kappe muss angebracht werden, falls Sie das Motherboard zur Reparatur bringen.
Schritt 3. 1366-Pin CPU einstecken:
Schritt 3-1. Halten Sie die CPU an den mit
schwarzen Linien gekennzeichneten Seiten.
Linie
Schwarze
Linie
Schwarze
Deutsch
DeutschDeutsch
DeutschDeutsch
4646
46
4646
Schritt 3-2. Halten Sie das Teil mit dem IHS
(Integrated Heat Sink – integrierter Kühlkörper) nach oben. Suchen Sie Pin 1 und die zwei Orientierungseinkerbungen.
Orientierungskerbe
Pin1
Orientierungskerbe
1366-Pin CPU
Pin1
ASRock X58 Extreme3 Motherboard
Ausrichtungsmarkierung
Ausrichtungsmarkierung
1366-Pin Sockel
Page 47
Um die CPU ordnungsgemäß einsetzen zu können, richten Sie die zwei Orientierungskerben der CPU mit den beiden
Markierungen des Sockels aus.
Schritt 3-3. Drücken Sie die CPU vorsichtig
in vertikaler Richtung in den Sockel.
Schritt 3-4. Prüfen Sie, dass die CPU
ordnungsgemäß im Sockel sitzt und die Orientierungskerben einwandfrei in den entsprechenden Auskerbungen sitzen.
Schritt 4. Sockel schließen:
Schritt 4-1. Drehen Sie die Ladeplatte auf
den Kühlkörper (IHS).
Schritt 4-2. Drücken Sie leicht auf die
Ladeplatte und schließen Sie den Ladehebel.
Schritt 4-3. Sichern Sie Ladehebel und
Ladeplatte mithilfe des Hebelverschlusses.
ASRock X58 Extreme3 Motherboard
4747
47
4747
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 48
2.22.2
Installation des CPU-Lüfters und KühlkörpersInstallation des CPU-Lüfters und Kühlkörpers
2.2
Installation des CPU-Lüfters und Kühlkörpers
2.22.2
Installation des CPU-Lüfters und KühlkörpersInstallation des CPU-Lüfters und Kühlkörpers
Für Installationshinweise, siehe Betriebsanleitung Ihres CPU-Lüfters und Kühlkörpers. Unten stehend ein Beispiel zur In stallation eines Kühlkörpers für den 1366-Pin CPU.
Schritt 1. Geben Sie Wärmeleitmaterial auf die Mitte
des IHS, auf die Sockeloberfläche.
Schritt 2. Setzen Sie den Kühlkörper auf den Sockel.
Prüfen Sie, dass die Lüfterkabel auf der Seite am nächsten zum CPU-Lüfter­Anschluss des Motherboards verlaufen (CPU_FAN1, siehe Seite 2, Nr. 2).
Schritt 3. Richten Sie Verbindungselemente und
Löcher im Motherboard aus.
Schritt 4. Drehen Sie die Verbindungselemente im
Uhrzeigersinn und drücken Sie mit dem Daumen auf die Kappen der Elemente zum Feststellen. Wiederholen Sie dies mit den anderen Verbindungselementen.
Wenn Sie die Verbindungselemente nur drücken, ohne sie im Uhrzeigersinn zu drehen, wird der Kühlkörper nicht ordnungsgemäß am Motherboard befestigt.
(Tragen Sie Wärmeleitmaterial auf. )
(Lüfterkabel auf der Seite am nächsten zum Anschluss des Motherboards)
(Schlitze der Verbindungselemente nach außen)
(Nach unten drücken (4 Stellen))
Deutsch
DeutschDeutsch
DeutschDeutsch
4848
48
4848
Schritt 5. Schließen Sie den Lüfter an den CPU-
Lüfteranschluss des Motherboards.
Schritt 6. Befestigen Sie überschüssiges Kabel mit
Band, um eine Störung des Lüfters oder Kontakt mit anderen Teilen zu vermeiden.
ASRock X58 Extreme3 Motherboard
Page 49
2.3 Installation der Speichermodule (DIMM)2.3 Installation der Speichermodule (DIMM)
2.3 Installation der Speichermodule (DIMM)
2.3 Installation der Speichermodule (DIMM)2.3 Installation der Speichermodule (DIMM)
Dieses Motherboard verfügt über sechs 240-pol. DDR3 (Double Data Rate 3) DIMM­Steckplätze und unterstützt Tri ple-Cha nnel-Speicherte chnologie. Für die T riple­Kanalkonfiguration dürfen Sie nur identische (gleiche M arke, Geschwindigke it, Größe und gleicher Chiptyp) DD R3 DIMM-Paare in den Steckplätzen gleicher Farbe installieren. Mit anderen W orten, sie müssen e in identisches DDR3 DIMM-Paar i m Triple-Ka nal (DDR3_A1, DDR3_B1 und DDR3_C1; We iß Steckplätze, siehe Seite 2 Nr. 7) oder ein identisches DDR3 DIMM-Paar i m T r i ple-Kanal (DDR3_A2, DDR3_B2 und DDR3_C2; Blau Steckplätze, siehe Se ite 2 Nr. 11) installieren, damit die Triple­Kanal-Speicherte chnologie aktiviert werden k ann. Auf die sem Motherboard können Sie auch sechs DDR3 DIMMs für eine Triple-Kan alkonfiguration installieren. Auf diese m Motherboard können Sie auch sechs DDR3 DIMM-Module für eine Tri ple­Kanalkonfiguration installieren, wobe i Sie bitte in allen sechs Steck plätzen identische DDR3 DIMM-Module installieren.
Empfohlene Speicherkonfigurationen
DDR3_A2 DDR3_A1 DD R3_B2 DDR3_B1 DD R3_C2 DDR3_C1
(Blau) (Weiß) (Blau) (Weiß) (Blau) (Weiß) 1 DIMM - Bestückt - - - ­ 2 DIMMs - Bestückt - Bestückt - ­ 3 DIMMs - Bestückt - Bestückt - Bestückt 4 DIMMs Bestückt Bestückt - Bestückt - Bestückt 5 DIMMs Bestückt Bestückt Bestückt Bestückt - Bestückt 6 DIMMs Bestückt Bestückt Bestückt Bestückt Bestückt Bestückt
1. Installieren Sie das Speichermodul für die erste Priorität im weißen Steckplatz (DDR3_A1, DDR3_B1 oder DDR3_C1).
2. Aufgrund der Intel® CPU-Spezifikationsdefinition startet das System nicht, wenn nur ein DIMM im DDR3_A2-, DDR3_B2- oder DDR3_C2-Steckplatz installiert ist.
3. Aufgrund der Intel® CPU-Spezifikationsdefinition werden XMP DIMMs und DDR3 1600 nur für ein DIMM pro Kanal unterstützt.
4. Sie können unterschiedliche Speichergrößen in Kanal A, Kanal B und Kanal C installieren. Das System bildet die Gesamtgröße des Kanals mit der geringeren Größe für die Dual-Channel- oder Triple-Channel-Konfiguration ab. Jeder darüber hinausgehende Speicher vom Kanal mit höherer Größe wird dann für Single­Channel-Betrieb abgebildet.
5. Es ist nicht gestattet, ein DDR- oder DDR2 –Speichermodul im DDR3-Steckplatz zu installieren; andernfalls können dieses Motherboard und das DIMM beschädigt werden.
ASRock X58 Extreme3 Motherboard
4949
49
4949
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 50
Einsetzen eines DIMM-ModulsEinsetzen eines DIMM-Moduls
Einsetzen eines DIMM-Moduls
Einsetzen eines DIMM-ModulsEinsetzen eines DIMM-Moduls
Achten Sie darauf, das Netzteil abzustecken, bevor Sie DIMMs oder Systemkomponenten hinzufügen oder entfernen.
Schritt 1: Öffnen Sie einen DIMM-Slot, indem Sie die se itlichen Clips n ach außen
drücken.
Schritt 2: Richten Sie das DIMM-Modul so über dem Slot aus, das s das Modul mit
der Kerbe in den Slot passt.
Deutsch
DeutschDeutsch
DeutschDeutsch
5050
50
5050
Die DIMM-Module passen nur richtig herum eingelegt in die Steckplätze. Falls Sie versuchen, die DIMM-Module mit Gewalt falsch herum in die Steckplätze zu zwingen, führt dies zu dauerhaften Schäden am Mainboard und am DIMM-Modul.
Schritt 3: Drücken Sie die DIMM-Module fest in die Ste ckplätze, so dass die
Halteklammern a n beiden Enden de s Moduls einschn a ppen und das DIMM-Modul fest an Ort und Stelle sitzt.
ASRock X58 Extreme3 Motherboard
Page 51
2.42.4
Erweiterungssteckplätze (PCI-Steckplätze und PCIErweiterungssteckplätze (PCI-Steckplätze und PCI
2.4
Erweiterungssteckplätze (PCI-Steckplätze und PCI
2.42.4
Erweiterungssteckplätze (PCI-Steckplätze und PCIErweiterungssteckplätze (PCI-Steckplätze und PCI ExpressExpress
Express
ExpressExpress
Es gibt einen 2 PCI-Steckplätze und 4 PCI Express-Steckplätze am X58 Extreme3 Motherboard.
PCI-Slots: PCI-Slots werden zur Installation von Erweiterungskarten mit
PCI Express-Slots:
-Steckplätze)-Steckplätze)
-Steckplätze)
-Steckplätze)-Steckplätze)
dem 32bit PCI-Interface genutzt.
PCIE2 (PCIE x1-Steckplatz; weiß) wird für PCI Express-Karten mit x1 Lane-Breite-Karten verwendet, z.B. Gigabit LAN-Karte, SATA2-Karte. PCIE1 / PCIE3 (PCIE x16-Steckplatz; blau) wird für PCI Express x16 Lane-Breite-Grafikkarten oder für die Installation von PCI Express-Grafikkarten verwendet, um die CrossFireXTM oder SLITM-Funktion zu unterstützen. PCIE4 (PCIE x16-Steckplatz; weiß) wird für PCI Express x1 Lane-Breite-Karten verwendet, z.B. Gigabit LAN-Karte, SATA2-Karte, etc.
1. Im Einzel-VGA-Kartenmodus wird empfohlen, eine PCI Express x16-Grafikkarte im PCIE1-Steckplatz zu installieren.
2. Im CrossFireXTM-Modus oder SLITM-Modus installieren Sie PCI Express x16-Grafikkarten in den PCIE1- und PCIE3-Steckplätzen. Daher funktionieren diese zwei Steckplätze mit x16-Bandbreite.
3. Verbinden Sie einen Gehäuselüfter mit dem Motherboard­Gehäuselüfteranschluss (CHA_FAN1 oder CHA_FAN2), wenn Sie mehrere Grafikkarten für eine bessere Wärmeumgebung verwenden.
Einbau einer ErweiterungskarteEinbau einer Erweiterungskarte
Einbau einer Erweiterungskarte
Einbau einer ErweiterungskarteEinbau einer Erweiterungskarte
Schritt 1: Bevor Sie die Erweiterungskarte installieren, vergewissern Sie sich,
dass das Netzteil ausge schaltet und das Netzka bel a bgezogen ist. Bitte lesen Sie die Dokumentation zur Erweiterungsk arte und nehmen Sie nötige Hardware-Einstellungen für die Karte vor, ehe Sie mit der Installation beginnen.
Schritt 2: Entfernen Sie das Abde ckungsblech (Slotblende) von dem
Gehäuseschacht (Slot) , den Sie nutzen möchten und behalten die Schraube für den Einbau der Karte.
Schritt 3: Richten Sie die Karte über dem Slot aus und drücken Sie sie ohne
Gewalt hinein, bis sie den Steckplatz korrekt ausfüllt.
Schritt 4: Befestigen Sie die Karte mit der Schraube aus Schritt 2.
ASRock X58 Extreme3 Motherboard
5151
51
5151
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 52
TMTM
TM
2.52.5
2.5
2.52.5
Dieses Motherboard unterstützt NVIDIA® SLITM- und Quad SLITM- (Scalable Link Interface) Technologie, die Ihnen die Installation von bis zu zwei identischen PCI Express x16-Grafikkarten gestattet. Derzeit unterstützt die NVIDIA® SLITM­Technologie die Betriebssysteme Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit / XP / XP 64-Bit. Die NVIDIA® Quad SLITM-Technologie unterstützt nur die Betriebssysteme Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit. Beachten Sie den detailliert erklärten Installationsablauf auf Seite 19.
TMTM
SLISLI
- und Quad SLI- und Quad SLI
SLI
- und Quad SLI
SLISLI
- und Quad SLI- und Quad SLI
TMTM
TM
TMTM
-Bedienungsanleitung-Bedienungsanleitung
-Bedienungsanleitung
-Bedienungsanleitung-Bedienungsanleitung
TMTM
TM
2.62.6
CrossFireXCrossFireX
2.6
CrossFireX
2.62.6
CrossFireXCrossFireX BedienungsanleitungBedienungsanleitung
Bedienungsanleitung
BedienungsanleitungBedienungsanleitung
Dieses Motherboard unterstützt die CrossFireXTM- und Quad CrossFireXTM­Funktion. CrossFireXTM-Technologie bietet die am vorteilhaftesten zur Verfügung stehende Methode zur Kombination mehrerer leistungsstarker Grafikprozessoren (GPU) in einem einzelnen PC. Die Kombination einer Reihe unterschiedlicher Betriebsmodi mit intelligentem Softwaredesign und einem innovativen Schaltmechanismus ermöglicht CrossFireXTM die optimalste Leistung und Bildqualität in einer 3D-Anwendung. Derzeit wird die CrossFireXTM-Funktion von den Betriebssystemen Windows® XP mit Service Pack 2 / VistaTM / 7 unterstützt. Quad CrossFireXTM-Funktion wird nur vom Betriebssystem Windows® VistaTM / 7 unterstützt. Schauen Sie auf der AMD-Website nach, ob es ATITM CrossFireXTM­Treiber-Updates gibt. Beachten Sie den detailliert erklärten Installationsablauf auf Seite 22.
TMTM
- und Quad CrossFireX- und Quad CrossFireX
- und Quad CrossFireX
- und Quad CrossFireX- und Quad CrossFireX
TMTM
TM
TMTM
--
-
--
Deutsch
DeutschDeutsch
DeutschDeutsch
5252
52
5252
ASRock X58 Extreme3 Motherboard
Page 53
2.7 “Surround Display”2.7 “Surround Display”
2.7 “Surround Display”
2.7 “Surround Display”2.7 “Surround Display”
Dieses Motherboard unterstützt Surround Display-Aufrüstung. M it zusätzlichen PCI Express-VGA-Karte können Sie die V orteile der Surround Display-Funktion problemlos genießen. Für detaillierte Informationen, siehe folgendes Dokument auf beiliegender Support-CD: ..\ Surround Display Information
2.8 Einstellung der Jumper2.8 Einstellung der Jumper
2.8 Einstellung der Jumper
2.8 Einstellung der Jumper2.8 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Gebrückt” sind, bzw. es befindet sich eine Jumper­Kappe auf diesen beiden Pins.
Jumper Einstellun Beschreibung
PS2_USB_PWR1 Überbrücken Sie Pin2, Pin3, um
(siehe S.2 - No. 1) +5VSB (Standby) zu setzen
Hinweis: Um +5VSB nutzen zu können, muss das Netzteil auf dieser Leitung 2A
oder mehr leisten können.
Gebrückt Offen
und die PS/2 oder USB­We ckfunktionen zu aktivieren.
CMOS löschen
(CLRCMOS1, 3-Pin jumper) (siehe S.2 - Nr. 15)
Hinweis: CLRCMOS1 erlaubt Ihnen das Löschen der CMOS-Daten. Diese beinhalten
das System-Passwort, Datum, Zeit und die verschiedenen BIOS-Parameter. Um die Systemparameter zu löschen und auf die Werkseinstellung zurückzusetzen, schalten Sie bitte den Computer ab und entfernen da s Stromkabel. Benutzen Sie eine Jumperkappe, um die Pin 2 und Pin 3 an CLRCMOS1 für 5 Sekunden kurzzuschließen. Bitte vergessen Sie nicht, den Jumper wieder zu entfernen, nachdem das CMOS gelöscht wurde. Bitte vergessen Sie nicht, den Jumper wieder zu entfernen, nachde m da s CMOS gelöscht wurde. W enn Sie den CMOS-Inhalt gleich n a ch de m Aktualisieren des BIOS löschen müssen, müssen Sie zuerst da s System starten und dann wieder ausschalten, bevor Sie den CMOS-Inhalt löschen.
Default­Einstellung
ASRock X58 Extreme3 Motherboard
CMOS löschen
5353
53
5353
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 54
Durch Löschen des CMOS kann erkannt werden, wenn das Gehäuse offen ist. Bitte stellen Sie zum Löschen der Aufzeichnung des vorherigen Gehäuseindringungsstatus die BIOS-Option “Status leeren” ein.
2.9 Integrierte Header und Anschlüsse2.9 Integrierte Header und Anschlüsse
2.9 Integrierte Header und Anschlüsse
2.9 Integrierte Header und Anschlüsse2.9 Integrierte Header und Anschlüsse
Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf diese He ader und Anschlüsse. Wenn Sie Jumperkappen auf Header und Anschlüsse setzen, wird das Motherboard unreparierbar beschädigt!
Anschluss für das Floppy-Laufwerk
(33-Pin FLOPPY1) (siehe S.2 - No. 31)
die rotgestreifte Seite auf Stift 1
Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Ka bel mit der Stift 1-
Seite des An schlusses verbunden wird.
Primärer IDE-Anschluss (blau)
(39-pin IDE1, siehe S.2 - No. 14)
Blauer Anschluss Schwarzer Anschluss zum Motherboard zur Festplatte
80-adriges A T A 66/100/133 Kabel
Hinweis: Details entnehmen Sie bitte den Anweisungen Ihres IDE-Gerätehändlers.
Deutsch
DeutschDeutsch
DeutschDeutsch
5454
54
5454
Seriell-ATAII-Anschlüsse Diese sechs Serial ATAII-
(SATAII_1_2: (SAT AII-)Verbínder unterstützten siehe S.2 - No. 16) SATA-Datenkabel für interne (SATAII_3_4: Massenspeichergeräte. Die siehe S.2 - No. 17) aktuelle SATAII-Schnittstelle (SATAII_5_6: ermöglicht eine siehe S.2 - No. 18) Datenübertragungsrate bis
3,0 Gb/s.
SAT AII_5_6 SA T AII_3_4 SA T AII_1_2
ASRock X58 Extreme3 Motherboard
Page 55
Seriell-ATA3-Anschlüsse Diese zwei Serial ATA3-
(SAT A3_1: siehe S.2 - No. 13) (SATA3-)Verbínder (SAT A3_2: siehe S.2 - No. 12) unterstützten SATA-Datenkabel
SAT A3_2
SAT A3_1
für interne Massen spe ichergeräte. Die aktuelle SATA3- Schnittstelle ermöglicht eine Datenübertragungsrate bis 6,0 Gb/s.
Serial A TA- (SATA-) SJedes Ende des SATA Datenkabel Datenkabels kann an die SATA
(Option) / SATAII / SATA3 Festplatte
oder das SATAII / SATA3 Verbindungsstück auf dieser Hauptplatine angeschlossen werden.
Serial A TA- (SATA-) Verbinden Sie das schwarze Stromversorgungskabel Ende des SATA-Netzkabels mit
(Option) dem Netzan schluss am
SATA-HDD-Stromanschluss
Verbindung zum
Verbindung zum Netzteil
Laufwerk. Verbinden Sie dann das weiße Ende des SATA­Stromversorgungskabels mit dem Stromanschluss des Netzteils.
USB 2.0-Header Zusätzlich zu den fünf
(9-pol. USB6_7) üblichen USB 2.0-Ports an den (siehe S.2 - No. 25) I/O-Anschlüssen befinden sich
zwei USB 2.0­Anschlussleisten am Motherboard. Pro USB 2.0-
(9-pol. USB8_9) Anschlussleiste werden zwei (siehe S.2 - No. 10) USB 2.0-Ports unterstützt.
ASRock X58 Extreme3 Motherboard
5555
55
5555
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 56
TPM-Stiftleiste Dieser Anschluss unterstützt ein
(19-Pin TPM1) Trusted Platform Module-System (siehe S.2 - No. 29) (TPM: Vertrauenswürdiges
Plattformmodul), auf dem sich Schlüssel, Digitalzertifikate, Kennwörter und Daten auf sichere We ise speichern lassen. Ein TPM-System hilft auch bei der Verbesserung der Netzwerksicherheit, schützt digitale Identitäten und sorgt für Plattformintegrität.
Infrarot-Modul-Header Dieser Header unterstützt ein
(5-pin IR1) optionales, drahtloses Sende- (siehe S.2 - No. 33) und Empfangs-Infrarotmodul.
Verteiler für Gehäuseeindringversuche Dieses Motherboard
(2-pin CI1) unterstützt die GEHÄUSE (siehe S.2 - No. 35) OFFEN-Erkennungsfunktion,
die feststellt, ob die Gehäuseabdeckung entfernt wurde. Für diese Funktion ist ein Gehäuse erforderlich, das mit einem De sign zur Erkennung von Gehäuseeindringversuchen ausgestattet ist.
Deutsch
DeutschDeutsch
DeutschDeutsch
5656
56
5656
Interne Audio-Anschlüsse Diese ermöglichen Ihnen
(4-Pin CD1) Stereo-Signalquellen, wie z. B. (siehe S.2 - No. 43) CD-ROM, DV D-ROM, TV-Tuner
CD1
oder MPEG-Karten mit Ihrem System zu verbinden.
Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorderseite
(9-Pin HD_AUDIO1) Ihres Gehäuses, ermöglicht (siehe S.2 - No. 44) Ihnen eine bequeme
Anschlussmöglichkeit und Kontrolle über Audio-Geräte.
ASRock X58 Extreme3 Motherboard
Page 57
1. High Definition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an. B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an. D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden. E. Rufen Sie das BIOS-Setup-Dienstprogramm auf. Wechseln Sie zu Erweiterte Einstellungen und wählen Sie Chipset-Konfiguration.
Setzen Sie die Option Frontleistenkontrolle von [Automatisch] auf
[Aktiviert].
System Panel-Header Dieser Header unterstützt
(9-pin PANEL1) mehrere Funktion der (siehe S.2 - No. 9) Systemvorderseite.
Gehäuselautsprecher-Header Schließen Sie den
(4-pin SPEAKER1) Gehäuselautsprecher a n (siehe S.2 - No. 21) diesen Header an.
Betriebs-LED-Header Bitte schließen Sie die
(3-pin PLED1) Betriebs-LED des Gehäuses (siehe S.2 - No. 20) zur Anzeige des
Systembetriebsstatus an diesem Header a n. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt i m S1­Zustand. Im S3-/S4- oder S5­Zustand (ausgeschaltet) leuchtet die LED nicht.
ASRock X58 Extreme3 Motherboard
5757
57
5757
DeutschDeutsch
DeutschDeutsch
Deutsch
Page 58
Gehäuse-, Notebook- und Stromlüfteranschlüsse
(4-pin CHA_FAN1) (siehe S.2 - No. 28)
(3-pin CHA_FAN2) (siehe S.2 - No. 6)
(3-pin NB_FAN1) (siehe S.2 - No. 42)
(3-pin PWR_FAN1) (siehe S.2 - No. 5)
Verbinden Sie die Lüfterkabel mit den Lüfteranschlüssen, wobei der schwarze Dra ht a n den Schutzleiterstift angeschlossen wird.
Deutsch
DeutschDeutsch
DeutschDeutsch
CPU-Lüfteranschluss Verbinden Sie da s CPU -
(4-pin CPU_FAN1) Lüfterkabel mit diesem (siehe S.2 - No. 2) Anschluss und passen Sie den
4 3 2 1
schwarzen Draht dem Erdungsstift an.
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss (Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den Pins 1 – 3.
Lüfter mit dreipoligem Anschluss installieren
ATX-Netz-Hea der V erbinden Sie die A TX-
(24-pin ATXPWR1) Stromversorgung mit diesem (siehe S.2 - No. 8) Header.
12 124
13
Obwohl dieses Motherboard einen 24-pol. ATX-Stromanschluss bietet, kann es auch mit einem modifizierten traditionellen 20-pol. ATX-Netzteil verwendet werden. Um ein 20-pol. ATX-Netzteil zu verwenden, stecken Sie den Stecker mit Pin 1 und Pin 13 ein.
Installation eines 20-pol. A TX-Netzteils
Pins 1–3 anschließen
12
1
24
13
5858
58
5858
ASRock X58 Extreme3 Motherboard
Page 59
aht a n den angeschlossen
ATX 12V Anschluss Bitte schließen Sie an diesen
(8-pin ATX12V1) Anschluss die A TX 12V (siehe S.2 - No. 3) Stromversorgung an.
Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur Verfügung stellt, kann sie noch arbeiten, wenn Sie einen traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die 4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.
8 5
4 1
8 5
en
llieren
Installation der 4-Pin A TX 12V Energieversorgung
4 1
IEEE-1394 Header Außer einem vorgegebenem
(9-pin FRONT_1394) IEEE-1394 Port auf dem Ein-/ (siehe S.2 - No. 27) Ausgabe Paneel, gibt es einen
IEEE-1394 Header (FRONT_1394) auf dieser Hauptplatine. Dieser IEEE-1394 Header ka nn einen IEEE-1394 Port unterstützen.
COM-Anschluss-Header Dieser COM-Anschluss-
(9-pin COM1) Header wird verwendet, um (siehe S.2 - No. 30) ein COM-Anschlussmodul zu
unterstützen.
HDMI_SPDIF-Anschluss Der HDMI_SPDIF-Anschluss
(HDMI_SPDIF1, dreipolig) stellt einen SPDIF- (siehe S.2 - No. 32) Audioausgang für eine HDMI-
VGA-Karte zur V erfügung und ermöglicht den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten, Projektoren,
12
24
LCD-Geräten an das System. Bitte verbinden Sie den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte mit diese m
DeutschDeutsch
1
13
Anschluss.
DeutschDeutsch
Deutsch
ASRock X58 Extreme3 Motherboard
5959
59
5959
Page 60
HDMI_SPDIF-Kabel Bitte verbinden Sie das
(Option) schwarze Ende (A) des
C
B
A
HDMI_SPDIF-Kabels mit dem HDMI_SPDIF-Anschluss am Motherboard. Schließen Sie dann das weiße Ende (B oder C) des HDMI_SPDIF-Kabels an den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte an.
A. Schwarzes Ende B. Weißes Ende (zweipolig) C. Weißes Ende (dreipolig)
2.102.10
SchnellschalterSchnellschalter
2.10
Schnellschalter
2.102.10
SchnellschalterSchnellschalter
Dieses Motherboard besitzt drei Schnellschalter: Netzschalter, Rücksetzschalter (Reset) und CMOS löschen-Schalter, mit denen Benutzer das System schnell ein-/ ausschalten oder zurücksetzen oder die CMOS-Werte löschen können.
Netzschalter Der Netzschalter ist ein
(PWRBTN) Schnellschalter, mit dem (siehe S.2 - No. 24) Benutzer das System schnell
ein-/ausschalten können.
Deutsch
DeutschDeutsch
DeutschDeutsch
6060
60
6060
Rücksetzschalter (Reset) Der Rücksetzschalter (Reset) ist
(RSTBTN) ein Schnellschalter, mit dem (siehe S.2 - No. 23) Benutzer das System schnell
RESET
zurücksetzen können.
CMOS löschen-Schalter Der CMOS löschen-Schalter ist
(CLRCBTN) ein Schnellschalter, mit dem (siehe S.2 - No. 17) Benutzer die CMOS-Werte
clr
CMOS
schnell löschen können.
Es ist Ihnen bei Einrichtung des Systemkennworts nicht gestattet, die Schalterfunktion Clear CMOS (CMOS löschen) zu verwenden. Wenn Sie die CMOS-Werte entfernen möchten, müssen Sie zuerst Ihr Systemkennwort entfernen, oder Sie können sich stattdessen auch auf die Beschreibung “Clear CMOS jumper” (CMOS löschen-Jumper) auf Seite 53 beziehen.
ASRock X58 Extreme3 Motherboard
Page 61
2.112.11
Debug-LEDDebug-LED
2.11
Debug-LED
2.112.11
Debug-LEDDebug-LED
Die integrierte Debug-LED liefert Codeinformationen, die eine Fehlerbehebung erleichtern. Siehe die Abbildungen auf den Seiten 33, 34 und 35 zum Ablesen der Debug-LED-Codes.
2.122.12
TT
2.12
2.122.12
Zur Treiberinstallation Sie bitte die Unterstützungs-CD in Ihr optisches Laufwerk ein. Anschließend werden die mit Ihrem System kompatiblen Treiber automatisch erkannt und auf dem Bildschirm angezeigt. Zur Installation der nötigen Treiber gehen Sie bitte der Reihe nach von oben nach unten vor. Nur so können die von Ihnen installierten Treiber richtig arbeiten.
reiberinstallationreiberinstallation
T
reiberinstallation
TT
reiberinstallationreiberinstallation
®®
®
2.132.13
Windows Windows
2.13
Windows
2.132.13
Windows Windows XP 64-Bit mit RAID-Funktionalität installierenXP 64-Bit mit RAID-Funktionalität installieren
XP 64-Bit mit RAID-Funktionalität installieren
XP 64-Bit mit RAID-Funktionalität installierenXP 64-Bit mit RAID-Funktionalität installieren
Wenn Sie die Betriebssysteme Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit auf Ihren SA TA- / SA TAII-Festplatten mit RAID-Funktionalität installieren möchten, entnehmen Sie die detaillierten Schritte bitte dem Dokument, das Sie unter folgendem Pfad auf der Unterstützungs-CD finden:
..\ RAID Installation Guide
2.142.14
WindowsWindows
2.14
Windows
2.142.14
WindowsWindows XP 64-Bit ohne RAID-Funktionalität installierenXP 64-Bit ohne RAID-Funktionalität installieren
XP 64-Bit ohne RAID-Funktionalität installieren
XP 64-Bit ohne RAID-Funktionalität installierenXP 64-Bit ohne RAID-Funktionalität installieren
Wenn Sie Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit / XP / XP 64-Bit ohne RAID-Funktionalität auf Ihren SATA / SATAII-Festplatten installieren, dann folgen Sie bitte je nach dem zu installierenden Betriebssystem den folgenden Schritten.
2.14.1 Windows2.14.1 Windows
2.14.1 Windows
2.14.1 Windows2.14.1 Windows installieren installieren
installieren
installieren installieren
Wenn Sie Windows® XP / XP 64-Bit ohne RAID-Funktionalität auf Ihren SATA / SAT AII­Festplatten installieren, gehen Sie bitte wie folgt vor.
Verwendung von SATA / SATAII-Festplatten ohne NCQ-Funktionen
SCHRITT 1: BIOS einrichten.
A. Rufen Sie das BIOS SETUP UTILITY auf, wählen Sie den „Adva nced“­ Bildschirm (Erweitert), dann „Storage Configuration“ (Storage-Konfiguration). B. Stellen Sie “SATAII-Konfiguration” auf [Erweitert] ein, stellen Sie danach “SATAII konfigureren als” auf [IDE] ein.
SCHRITT 2: Installieren Sie Windows® XP / XP 64-Bit in Ihrem System.
®®
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
®®
®
®®
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
®®
®
®®
XP / XP 64-Bit ohne RAID-Funktionalität XP / XP 64-Bit ohne RAID-Funktionalität
XP / XP 64-Bit ohne RAID-Funktionalität
XP / XP 64-Bit ohne RAID-Funktionalität XP / XP 64-Bit ohne RAID-Funktionalität
TMTM
TM
TMTM
/ Vista / Vista
/ Vista
/ Vista / Vista
TMTM
TM
TMTM
/ Vista / Vista
/ Vista
/ Vista / Vista
TMTM
TM
TMTM
64-Bit / XP / 64-Bit / XP /
64-Bit / XP /
64-Bit / XP / 64-Bit / XP /
TMTM
TM
TMTM
64-Bit / XP / 64-Bit / XP /
64-Bit / XP /
64-Bit / XP / 64-Bit / XP /
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock X58 Extreme3 Motherboard
6161
61
6161
Page 62
®®
®
2.14.2 Windows2.14.2 Windows
2.14.2 Windows
2.14.2 Windows2.14.2 Windows ohne RAID-Funktionalität installieren ohne RAID-Funktionalität installieren
ohne RAID-Funktionalität installieren
ohne RAID-Funktionalität installieren ohne RAID-Funktionalität installieren
Wenn Sie Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit ohne RAID-Funktionalität auf Ihren SATA / SATAII-Festplatten installieren, gehen Sie bitte wie folgt vor.
Verwendung von SATA / SATAII-Festplatten ohne NCQ-Funktionen
SCHRITT 1: BIOS einrichten.
A. Rufen Sie das BIOS SETUP UTILITY auf, wählen Sie den „Adva nced“­ Bildschirm (Erweitert), dann „Storage Configuration“ (Storage-Konfiguration). B. Stellen Sie “SATAII-Konfiguration” auf [Erweitert] ein, stellen Sie dan a ch “SATAII konfigureren als” auf [IDE] ein.
SCHRITT 2: Installieren Sie Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit in
Ihrem System.
Verwendung von SATA / SATAII-Festplatten mit NCQ-Funktionen
SCHRITT 1: BIOS einrichten.
A. Rufen Sie das BIOS SETUP UTILITY auf, wählen Sie den „Adva nced“­ Bildschirm (Erweitert), dann „Storage Configuration“ (Storage-Konfiguration). B. Stellen Sie “SATAII-Konfiguration” auf [Erweitert] ein, stellen Sie dan a ch “SATAII konfigureren als” auf [AHCI] ein.
SCHRITT 2: Installieren Sie Windows® 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit in
Ihrem System.
®®
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista
7 / 7 64-Bit / Vista 7 / 7 64-Bit / Vista
TMTM
TM
TMTM
/ Vista / Vista
/ Vista
/ Vista / Vista
TMTM
TM
TMTM
64-Bit 64-Bit
64-Bit
64-Bit 64-Bit
Deutsch
DeutschDeutsch
DeutschDeutsch
6262
62
6262
ASRock X58 Extreme3 Motherboard
Page 63
3. BIOS-Information3. BIOS-Information
3. BIOS-Information
3. BIOS-Information3. BIOS-Information
Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie <F2> während des POST (Power-On-Self-Test) um ins Setup zu gela ngen, a n son sten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch durchführen, indem Sie das System kurz ab- und danach wieder anschalten. Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der Support CD.
4. Sof4. Sof
4. Sof
4. Sof4. Sof
Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows Betriebssystemen: 7 / 7 64-Bit / VistaTM / Vista Motherboard beigefügte Support-CD enthält hilfreiche Software, Treiber und Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben. Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File ASSETUP.EXE im BIN-Verze ichnis der Support-CD, um die Menüs aufzurufen. Das Setup-Progra mm soll es Ihnen so le icht wie möglich ma chen. Es ist menügesteuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und die Programme werden dann automatisch installiert.
tware Supportware Suppor
tware Suppor
tware Supportware Suppor
t CD informationt CD information
t CD information
t CD informationt CD information
®
TM
64-Bit / XP / XP 64-Bit. Die Ihrem
DeutschDeutsch
DeutschDeutsch
Deutsch
ASRock X58 Extreme3 Motherboard
6363
63
6363
Page 64
Français
FrançaisFrançais
FrançaisFrançais
1. Introduction1. Introduction
1. Introduction
1. Introduction1. Introduction
Merci pour votre achat d’une carte mère ASRock X58 Extreme3, une carte mère très fiable produite selon les critères de qualité rigoureux de ASRock. Elle offre des performances excellentes et une conception robuste conformément à l’engagement d’ASRock sur la qualité et la fiabilité au long terme. Ce Guide d’installation rapide présente la carte mère et constitue un guide d’installation pas à pas. Des informations plus détaillées concernant la carte mère pourront être trouvées dans le ma nuel l’utilisateur qui se trouve sur le CD d’assista nce.
Les spécifications de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notification. Au cas où n’importe qu’elle modification intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis. Vous trouverez les listes de prise en charge des cartes VGA et CPU également sur le site Web ASRock. Site web ASRock, http://www.asrock.com Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez. www.asrock.com/support/index.asp
1.1 Contenu du paquet1.1 Contenu du paquet
1.1 Contenu du paquet
1.1 Contenu du paquet1.1 Contenu du paquet
Carte mère ASRock X58 Extreme3
(Facteur de forme ATX: 12.0 pouce s x 9.6 pouces, 30.5 cm x 24.4 cm) Guide d’installation rapide ASRock X58 Extreme3 CD de soutien ASRock X58 Extreme3 Un câble ruba n IDE Ultra ATA 66/100/133 80 conducteurs Un câble ruba n pour un lecteur de dis quettes 3,5 pouces Quatre câbles de données de série ATA (SATA) (en option) Deux câble d’alimentation de série AT A (SAT A) HDD (en option) Un I/O Pa nel Shield Un carte 2S_Pont_ASRock SLI
6464
64
6464
ASRock X58 Extreme3 Motherboard
Page 65
1.21.2
SpécificationsSpécifications
1.2
Spécifications
1.21.2
SpécificationsSpécifications
Format - Facteur de forme A TX:
12.0 pouces x 9.6 pouces, 30.5 cm x 24.4 cm
- Accessoire s de Carte mère (condensateurs 100% polymère conducteur de haute qualité fabriqué au Ja pon)
CPU - Douille Intel® 1366 CoeurTM i7 Processeur Extrême Edition /
CoeurTM i7. Le Processeur prend en charge la technologie Intel Dynamic Speed
- Bus de système 6400 MT/s; interconnexion Intel® QuickPath
- Conception avancée V8 Power Phase
- Prise en charge de la technologie Hyper-Threading (voir ATTENTION 1)
- Prend en charge la technologie Untied Overclocking
(voir ATTENTION 2)
- Prise en charge de la technologie EM64T par le CPU
Chipsets - Northbridge: Intel® PX58
- Southbridge: Intel® ICH10R
Mémoire - Technologie de mémoire de DDR3 tri ple chaîne
(voir ATTENTION 3)
- 6 x slots DIMM DDR3
- Supporter DDR3 2000(OC)/1866(OC)/1600(OC)/1333(OC)/ 1066 non-ECC, sans amortissement mémoire
- Prend en charge DDR3 ECC, sans amortissement mémoire avec Intel® station de travail processeurs 1S Xeon® série 3500
- Capacité maxi de mémoire système: 24GB (voir ATTENTION 4)
- Prend en charge le profil de mémoire extrême Intel® (XMP)
Slot d’extension - 2 x slot PCI Express 2.0 x16 (bleu @ x16 modes)
- 1 x slot PCI Express x16 (blanc@ x4 mode) (espacement faisant deux fois la taille d’une fente entre chaque fente PCI-E)
- 1 x slot PCI Express x1
- 2 x slots PCI
- Prend en charge ATITM CrossFireXTM et Quad CrossFireX
- Prend en charge NVIDIA® SLITM et Quad SLI
Audio - 7,1 CH HD Audio avec protection de contenu
- DAC avec une gamme dynamique 110dB (VIA® VT2020 Audio Codec)
- Prise en charge de l’audio Premium Blu-ray
TM
®
TM
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
ASRock X58 Extreme3 Motherboard
6565
65
6565
Page 66
Français
FrançaisFrançais
FrançaisFrançais
6666
66
6666
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL81 11DL
- Support du Wake-On-LAN
Panneau arrière I/O Panel
- 1 x port souris PS/2
- 1 x port clavier PS/2
- 1 x Port de sortie coaxial SPDIF
- 1 x Port de sortie optique SPDIF
- 5 x ports USB 2.0 par défaut
- 1 x Connecteur eSATAIII/USB 2.0 alimenté
- 2 x ports USB 3.0 par défaut
- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOT ANTE et LED VITESSE)
- 1 x port IEEE 1394
- 1 x interrupteur d’effacement du CMOS
- Prise HD Audio: Haut-parleur latéral / Haut-parleur arrière / Central /Basses / Entrée Ligne / Haut-parleur frontal / Microphone (voir ATTENTION 5)
SATA3 - 2 x connecteurs SATA3 6,0 Gb/s par Marvell SE9128,
prennent en charge les fonctions RAID matériel (RAID 0 et RAID 1), NCQ, AHCI et « Hot Plug » (Branchement à chaud) (le connecteur SATA3_2 est partagé avec le port eSATA3)
USB 3.0 - 2 x ports USB3.0 par NEC UPD720200, prennent en charge
USB 1.0/2.0/3.0 jusqu’à 5 Gb/s
Connecteurs - 6 x connecteurs SATAII, prennent en charge un taux de
transfert de données pouvant aller jusqu’à 3.0Go/s, supporte RAID (RAID 0, RAID 1,RAID 10, RAID 5 et mémoire à sélection matricielle), NCQ, AHCI et “Hot-Plug” (Connexion à chaud)
- 2 x connecteurs SATA3, prennent en charge un taux de transfert de données pouvant aller jusqu’à 6.0Go/s
- 1 x ATA133 IDE connecteurs (prend en charge jusqu’à 2 périphériques IDE)
- 1 x Port Dis quette
- 1 x En-tête du module infrarouge
- 1 x En-tête de port COM
- 1 x Connecteur HDMI_SPDIF
- 1 x Connecteur IEEE 1394
- 1 x connecteur TPM
- 1 x connecteur TPM
- 1 x Embase d’intrusion châssis
- Connecteur pour processeur/châssis/NB/ventilateur
- br. 24 connecteur d’alimentation ATX
ASRock X58 Extreme3 Motherboard
Page 67
- br. 8 connecteur d’alimentation 12V ATX
- Connecteurs audio internes
- Connecteur audio panneau avant
- 2 x En-tête USB 2.0 (prendre en charge 4 ports USB 2.0
supplémentaires) (voir ATTENTION 6) Interrupteur - 1 x interrupteur d’effacement du CMOS avec LED rapide - 1 x interrupteur d’alimentation avec LED
- 1 x interrupteur de réinitialisation avec LED
BIOS - 8Mb BIOS AMI
- BIOS AMI
- Support du “Plug and Play”
- Compatible pour événements de réveil ACPI 1.1
- Gestion jumperless
- Support SMBIOS 2.3.1
- CPU, VCCM, IOH, ICH, VTT, IOH/ICH PCIE, CPU PLL, IOH CSI,
VCORE Tension Multi-ajustement
- Supporter I. O. T. (Technologie d’Overclocking Intelligent)
CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (Version d’essai), Suite
logicielle ASRock (CyberLink DVD Suite et Creative Sound
Blaster X-Fi MB) (Version OEM et d’essai)
Caractéristique - Tuner ASRock OC (voir ATTENTION 7) unique - Économiseur d’énergie intelligent (voir ATTENTION 8)
- l'Instant Boot
- ASRock Instant Flash (voir ATTENTION 9)
- ASRock OC DNA (voir ATTENTION 10)
- L’accélérateur hybride:
- Contrôle direct de la fréquence CPU (voir ATTENTION 11)
- ASRock U-COP (voir ATTENTION 12)
- Garde d’échec au démarrage (B.F.G.)
- DEL veilleuse Surveillance - Contrôle de la température CPU système - Mesure de température de la carte mère
- Tachéomètre ventilateur processeur/châssis/NB/ventilateur
- Ventilateur silencieux d’unité centrale
- Commande de ventilateur CPU/boîtier à plusieurs vitesses
- Détection d’OUVERTURE DE BOÎTIER
- Monitoring de la tension: +12V, +5V, +3.3V, Vcore OS - Microsoft® Windows® 7 / 7 64-bit / VistaTM / Vista
/ XP / XP 64-bit
Certifications - FCC, CE, WHQL
- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)
(voir ATTENTION 13)
ASRock X58 Extreme3 Motherboard
TM
64-bit
6767
67
6767
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 68
Français
FrançaisFrançais
FrançaisFrançais
6868
68
6868
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web:
http://www.asrock.com
A TTENTION
Il est important que vous réalisiez qu’il y a un certain risque à effectuer l’overclocking, y compris ajuster les réglages du BIOS, appliquer la technologie Untied Overclocking, ou utiliser des outils de tiers pour l’overclocking. L’overclocking peut affecter la stabilité de votre système, ou même causer des dommages aux composants et dispositifs de votre système. Si vous le faites, c’est à vos frais et vos propres risques. Nous ne sommes pas responsables des dommages possibles causés par l’overclocking.
ATTENTION!
1. En ce qui concerne le paramétrage “Hyper-Threading Technology”, veuillez consulter la page 62 du manuel de l’utilisateur sur le CD technique.
2. Cette carte mère prend en charge la technologie Untied Overclocking. Veuillez lire “La technologie de surcadençage à la volée” à la page 37 pour plus d’informations.
3. Cette carte mère supporte la Technologie de Mémoire à Canal Triple. Avant d’intégrer la Technologie de Mémoire à Canal Triple, assurez­vous de bien lire le guide d’installation des modules mémoire en page 74 pour réaliser une installation correcte.
4. Du fait des limites du système d’exploitation, la taille mémoire réelle réservée au système pourra être inférieure à 4 Go sous Windows® 7 / VistaTM / XP. Avec Windows® OS avec CPU 64 bits, il n’y a pas ce genre de limitation.
5. Pour l’entrée microphone, cette carte mère supporte les deux modes stéréo et mono. Pour la sortie audio, cette carte mère supporte les modes 2-canaux, 4-canaux, 6-canaux et 8-canaux. Veuillez vous référer au tableau en page 3 pour effectuer la bonne connexion.
6. La gestion de l’alimentation pour l’USB 2.0 fonctionne bien sous Microsoft® Windows® 7 64-bit / 7 / VistaTM 64-bit/ VistaTM / XP 64-bit / XP SP1; SP2.
7. Il s’agit d’un usage facile ASRock overclocking outil qui vous permet de surveiller votre système en fonction de la monitrice de matériel et overclocker vos périphériques de matériels pour obtenir les meilleures performances du système sous environnement Windows®. S’il vous plaît visitez notre site web pour le fonctionnement des procédures de Tuner ASRock OC. ASRock website: http://www.asrock.com
8. Comprenant une conception matérielle et logicielle propriétaire avancée, Intelligent Energy Saver est une technologie révolutionnaire qui offre des gains d’énergie incomparables. En d’autres termes, il est capable d’apporter des économies d’énergie exce ptionnelle s et d’améliorer l’efficacité énergétique sans sacrifier aux performances de calcul. Veuillez visiter notre site Web pour les procédures d’utilisation d’Intelligent Energy Saver. Site Web ASRock : http://www.asrock.com
ASRock X58 Extreme3 Motherboard
Page 69
9. O ASRock Instant Flash é um utilitário de flash do BIOS incorporado na memória Flash ROM. Esta prática ferramenta de actualização do BIOS permite-lhe actualizar o BIOS do sistema sem necessitar de entrar nos sistemas operativos, como o MS-DOS ou o Windows®. Com este utilitário, poderá premir a tecla <F6> durante o teste de arranque POST ou premir a tecla <F2> para exibir o menu de configuração do BIOS para aceder ao ASRock Instant Flash. Execute esta ferramenta para guardar o novo ficheiro de BIOS numa unidade flash USB, numa disquete ou num disco rígido, em seguida, poderá actualizar o BIOS com apenas alguns cliques sem ter de utilizar outra disquete ou outro complicado utilitário de flash. Note que a unidade flash USB ou a unidade de disco rígido devem utilizar o sistema de ficheiros FAT32/16/
12.
10. Le nom même du logiciel – OC DNA vous indique littéralement ce dont il est capable. OC DNA, utilitaire exclusif développé par ASRock, offre une façon pratique pour l’utilisateur d’enregistrer les paramètres d’overclockage et de les partager avec d’autres. Il vous aide à enregistrer votre overclockage sous le système d’exploitation et simplifie le processus compliqué d’enregistrement des paramètres d’overclockage. Avec OC DNA , vous pouvez enregistrer vos réglages d’overclockage en tant que profil et les partager avec vos amis ! Vos amis peuvent alors charger le profil d’overclockage sur leur propre système pour obtenir les mêmes réglages d’overclockage que les vôtres ! Veuillez noter que le profil d’overclockage peut être partagé et utilisé uniquement sur la même carte mère.
11. Même si cette carte mère offre un contrôle sans souci, il n’est pas recommandé d’y appliquer un over clocking. Des fréquences de bus CPU autres que celles recommandées risquent de rendre le système instable ou d’endommager le CPU et la carte mère.
12. Lorsqu’une surchauffe du CPU est détectée, le système s’arrête automatiquement. Avant de redémarrer le système, veuillez vérifier que le ventilateur d’UC sur la carte mère fonctionne correctement et débranchez le cordon d’alimentation, puis rebranchez-le. Pour améliorer la dissipation de la chaleur, n’oubliez pas de mettre de la pâte thermique entre le CPU le dissipateur lors de l’installation du PC.
13. EuP, qui signifie Energy Using Product (Produit Utilisant de l’Energie), est une disposition établie par l’Union Européenne pour définir la consommation de courant pour le système entier. Conformément à la norme EuP, le courant CA total du système entier doit être inférieur à 1 W en mode d’arrêt. Pour être conforme à la norme EuP, une carte mère EuP et une alimentation EuP sont requises. Selon les suggestions d’Intel’, l’alimentation électrique EuP doit correspondre à la norme, qui est que l’efficacité électrique de 5v en mode de veille doit être supérieure à 50% pour 100 mA de consommation de courant. Pour choisir une alimentation électrique conforme à la norme EuP, nous vous recommandons de consulter votre fournisseur de courant pour plus de détails.
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
ASRock X58 Extreme3 Motherboard
6969
69
6969
Page 70
2. Installation2. Installation
2. Installation
2. Installation2. Installation
Précautions à observer avant l’installationPrécautions à observer avant l’installation
Précautions à observer avant l’installation
Précautions à observer avant l’installationPrécautions à observer avant l’installation
Veuillez tenir compte des précautions suivantes avant l’installation des composants ou tout réglage de la carte mère.
1. Débranchez le câble d’alimentation de la prise secteur avant de toucher à tout composant. En ne le faisant pas, vous pouvez sérieusement endommager la carte mère, les périphériques et/ou les composants.
2. Pour éviter d’endommager les composants de la carte mère du fait de l’électricité statique, ne posez JAMAIS votre carte mère directement sur de la moquette ou sur un tapis. N’oubliez pas d’utiliser un bracelet antistatique ou de toucher un objet relié à la masse avant de manipuler les composants.
3. Tenez les composants par les bords et ne touchez pas les circuits intégrés.
4. A chaque désinstallation de composant, placez-le sur un support antistatique ou dans son sachet d’origine.
5. Lorsque vous placez les vis dans les orifices pour vis pour fixer la carte mère sur le châssis, ne serrez pas trop les vis ! Vous risquez sinon d’endommager la carte mère.
2.1 Installation du CPU2.1 Installation du CPU
2.1 Installation du CPU
2.1 Installation du CPU2.1 Installation du CPU
Pour l’installation du processeur Intel 1366 broches, veuillez suivre la procédure ci-dessous.
(Plaque de chargement)
(Barrette de contact)
(Corps du socket)
Français
FrançaisFrançais
FrançaisFrançais
7070
70
7070
Vue d’ensemble du socket 1366 broches
Avant d’insérer le processeur 1366 broches dans le socket, veuillez vérifier que la surface du processeur est bien propre, et qu’il n’y a aucune broche tordue sur le socket. Si c’est le cas, ne forcez pas pour insérer le processeur dans le socket. Sinon, le processeur sera gravement endommagé.
ASRock X58 Extreme3 Motherboard
Page 71
Etape 1. Ouvrez le socle :
Etape 1-1. Dégagez le levier en appuyant sur le
crochet et en le faisant ressortir pour dégager la languette de retenue.
Etape 1-2. Faites tourner le levier de
chargement en position ouverte maximum à 135 degrés.
Etape 1-3. Faites pivoter la plaque de
chargement pour l’ouvrir au maximum à environ 100 degrés.
Etape 2. Enlevez le capuchon PnP (Pick et Place).
1. Il est recommandé d’utiliser la languette du capuchon ; évitez de faire sortir le capuchon PnP.
2. Ce capuchon doit être mis en place si vous renvoyez la carte mère pour service après vente.
Etape 3. Insérez le processeur 1366 broches :
Etape 3-1. Tenez le processeur par ses bords
là où se trouvent des lignes noires.
Ligne noire
Ligne noire
Etape 3-2. Orientez le paquet avec le
dissipateur thermique intégré (IHS) vers le haut. Repérez la broche 1 et les deux encoches d’orientation.
Encoche d’orientation
broche 1
Encoche d’orientation
Processeur 1366 broches
ASRock X58 Extreme3 Motherboard
broche 1
Détrompeur
Détrompeur
Socket 1366 broches
7171
71
7171
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 72
Pour une insertion correcte, veuillez vérifier que vous faites bien correspondre les deux encoches d’orientation sur le processeur
avec les deux détrompeurs du socket
Etape 3-3. Mettez soigneuse ment en place le
processeur dans le socle en un mouvement strictement vertical.
Etape 3-4. Vérifiez que le proce sseur est bien
installé dans le socle et que les encoches d’orientation sont dans la bonne position.
Etape 4. Refermez le socle :
Etape 4-1. Faites pivoter la plaque de
chargement sur l’IHS.
Etape 4-2. Tout en appuyant doucement sur
la plaque de chargement, engagez le levier de chargement.
Etape 4-3. Fixez le levier de chargement avec
la languette de la plaque de chargement sous la languette de retenue du levier de chargement.
.
Français
FrançaisFrançais
FrançaisFrançais
7272
72
7272
ASRock X58 Extreme3 Motherboard
Page 73
2.22.2
Installation du ventilateur du processeur etInstallation du ventilateur du processeur et
2.2
Installation du ventilateur du processeur et
2.22.2
Installation du ventilateur du processeur etInstallation du ventilateur du processeur et dissipateur thermiquedissipateur thermique
dissipateur thermique
dissipateur thermiquedissipateur thermique
Pour une installation correcte, veuillez vous reporter aux manuels d’instructions de votre ventilateur de processeur et de votre dissipateur thermique.
L’exemple ci-dessous illustre l’installation du dissipateur thermique pour un processeur 1366 broches.
Etape 1. Appliquez le matériau d’interface thermique
au centre de IHS sur la surface du socket.
Etape 2. Placez le dissipateur thermique sur le socket.
Vérifiez que les câbles du ventilateur sont orientés vers le côté le plus proche du connecteur pour ventilateur de processeur sur la carte mère (CPU_FAN1, voir page 2, no. 2).
Etape 3. Alignez les attaches avec la carte mère par
les orifices.
Etape 4. Faites tourner les attaches dans le sens des
aiguilles d’une montre, puis, du pouce, enfoncez les capuchons des attaches pour les installer et les verrouiller. Répétez l’opération avec les autres attaches.
(Appliquez le matériau d’interface thermique)
(Câbles du ventilateur du côté le plus proche du connecteur sur la carte mère)
(Orifices des attaches ressortant)
(Enfoncez (4 endroits))
Si vous enfoncez les attaches sans les faire tourner dans le sens des aiguilles d’une montre, le dissipateur thermique ne sera pas fixé sur la carte mère.
Etape 5. Connectez l’en-tête du ventilateur sur le
connecteur pour ventilateur de processeur sur la carte mère.
Etape 6. Fixez la longueur de câble en excès avec du
ruban adhésif pour vous assurer que le câble ne gênera pas le fonctionnement du ventilateur ou n’entrera pas en contact avec les autres composants.
ASRock X58 Extreme3 Motherboard
7373
73
7373
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 74
2.3 Installation des modules m émoire [DIMM]2.3 Installation des modules m émoire [DIMM]
2.3 Installation des modules m émoire [DIMM]
2.3 Installation des modules m émoire [DIMM]2.3 Installation des modules m émoire [DIMM]
Cette carte mère offre six fentes DIMM 240 broches pour DDR3 (mémoire à double débit de données 3), et prend en charge la technologie de mémoire triple chaîne. Pour effectuer une configuration à ca nal tri ple, vous devez toujours installer des paires de DIMM DDR3 identique s (de la même marque, de la même vitesse, de la même taille et du même type de puce) dans les slots de même couleur. En d’autres termes, vous devez installer une paire de DIMM DD R3 identiques da ns le Ca nal T riple (DD R3_A1, DDR3_B1 et DD R3_C1; slots bla nc; voir p.2 No. 7) ou une paire de DIMM DDR3 identiques dans le Ca nal T riple (DD R3_A2, DDR3_B2 et DD R3_C2; slots bleu; voir p.2 No. 11), de façon à ce que la Technologie de Mémoire à Canal Triple puisse être activée. Cette carte vous permet également d’installer six module s DIMM DDR3 pour la configuration à canal triple. Cette carte mère vous permet égale ment d’installer quatre modules DIMM DDR3 pour une configuration triple canal; veuillez installer les mêmes modules DIMM DDR3 dans les six emplacements.
Configurations de mémoire recommandée
DDR3_A2 DDR3_A1 DD R3_B2 DDR3_B1 DDR3_C2 DDR3_C1
(Bleu) (Blanc) (Bleu) (Blanc) (Bleu) (Blanc) 1 DIMM - Occupé - - - ­ 2 DIMMs - Occupé - Occupé - ­ 3 DIMMs - Occupé - Occupé - Occupé 4 DIMMs Occupé Occupé - Occupé - Occupé 5 DIMMs Occupé Occupé Occupé Occupé - Occupé 6 DIMMs Occupé Occupé Occupé Occupé Occupé Occupé
Français
FrançaisFrançais
FrançaisFrançais
7474
74
7474
1. Veuillez tout d’abord installer le module de mémoire dans la fente blanche (DDR3_A1, DDR3_B1 ou DDR3_C1).
2. Etant donnée la définition spécifique du processeur Intel® CPU, le système ne sera pas lancé si un DIMM est installé dans une fente DDR3_A2, DDR3_B2 ou DDR3_C2.
3. Etant donnée la définition spécifique du processeur Intel®, les XMP DIMM et DDR3 1600 sont pris en charge avec un DIMM par chaîne uniquement.
4. Vous pouvez installer des mémoires de diverses tailles dans la Chaîne A, la Chaîne B et la Chaîne C. Le système détermine la taille totale de la chaîne la plus petite pour la configuration de la chaîne double ou de la chaîne triple. Toute mémoire excédentaire de la chaîne la plus grande sera donc établie pour les opérations mono-chaîne.
5. Il est interdit d’installer un module de mémoire DDR ou DDR2 dans une fente DDR3 ; autrement, cette carte mère et ce DIMM pourraient être endommagés.
ASRock X58 Extreme3 Motherboard
Page 75
Installation d’un module DIMMInstallation d’un module DIMM
Installation d’un module DIMM
Installation d’un module DIMMInstallation d’un module DIMM
Ayez bien le soin de débrancher l’alimentation avant d’ajouter ou de retirer des modules DIMM ou les composants du système.
Etape 1. Déverrouillez un connecteur DIMM en poussant les taquets de maintien
vers l’extérieur.
Etap e 2 . Alignez le module DIMM sur son emplacement en faisant correspondre les
encoches du module DIMM aux trous du connecteur.
Le module DIMM s’insère uniquement dans un seul sens. Si vous forcez le module DIMM dans son emplacement avec une mauvaise orientation cela provoquera des dommages irrémédiables à la carte mère et au module DIMM.
Etape 3. Insérez fermement le module DIMM dans son empla ce ment jusqu’à ce que
les clips de maintien situés aux deux extrémités se ferment complètement et que le module DIMM soit inséré corre ctement.
ASRock X58 Extreme3 Motherboard
7575
75
7575
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 76
Français
FrançaisFrançais
FrançaisFrançais
2.42.4
Slot d’extension (Slots PCI et Slots PCI Express)Slot d’extension (Slots PCI et Slots PCI Express)
2.4
Slot d’extension (Slots PCI et Slots PCI Express)
2.42.4
Slot d’extension (Slots PCI et Slots PCI Express)Slot d’extension (Slots PCI et Slots PCI Express)
Il y a 2 ports PCI et 4 ports PCI Express sur la carte mère X58 Extreme3. Slots PCI: Les slots PCI sont utilisés pour installer des cartes d’extension dotées
d’une interface PCI 32 bits.
Slots PCIE:
Le PCIE2 (slot PCIE x1; blanc) sert aux cartes PCI Express avec les cartes de largeur x1 voie, comme la carte Gigabit LAN, la carte SATA2. Le PCIE1 / PCIE3 (slot PCIE x16; bleu) sert aux cartes graphiques PCI Express de largeur x16 voies, ou sert à installer des cartes graphiques PCI Express pour prendre en charge la fonction CrossFireXTM ou SLITM. Le PCIE4 (slot PCIE x16; blanc) sert aux cartes graphiques PCI Express de largeur x1 voie, comme la carte Gigabit LAN, la carte SATA2, etc.
1. En mode de carte VGA unique, il est recommandé d’installer une carte graphique PCI Express x16 dans la fente PCIE1.
2. En mode CrossFireXTM ou SLITM, installez une carte graphique PCI Express x16 dans les fentes PCIE1 et PCIE3. Par conséquent, ces deux fentes fonctionneront avec une largeur de bande x16.
3. Reliez un ventilateur de châssis au connecteur pour ventilateur de châssis de la carte mère (CHA_FAN1 ou CHA_FAN2) lorsque vous utilisez plusieurs cartes graphiques afin d’obtenir un meilleur environnement thermique.
Installation d’une carte d’extensionInstallation d’une carte d’extension
Installation d’une carte d’extension
Installation d’une carte d’extensionInstallation d’une carte d’extension
Etape 1. Avant d’installer les cartes d’extension, veuillez vous assurer de bien
avoir coupé l’alimentation ou d’avoir débranché le cordon d’ali mentation. Veuillez lire la documentation des cartes d’extension et effe ctuer le s réglages matériels nécessaires pour les cartes ava nt de débuter l’installation.
Etape 2. Retirez l’équerre correspondant au connecteur que vous voulez utiliser .
Gardez la vis pour un usage ultérieur.
Etape 3. Alignez la carte sur le connecteur et appuyez fermement jusqu’à l’insertion
complète de la carte dans son emplacement.
Etape 4. Fixez la carte sur le châssis à l’aide d’une vis.
7676
76
7676
ASRock X58 Extreme3 Motherboard
Page 77
TMTM
TM
2.52.5
Mode d’emploi pour SLIMode d’emploi pour SLI
2.5
Mode d’emploi pour SLI
2.52.5
Mode d’emploi pour SLIMode d’emploi pour SLI
Cette carte mère prend en charge les technologies NVIDIA® SLITM et Quad SLI (Interface de lien extensible) qui vous permettront d’installer jusqu’à deux cartes graphiques PCI Expre ss x16 identiques. En général, la technologie NVIDIA® SLI prend en charge Windows® 7 / 7 64 octets / VistaTM / VistaTM 64 octets / XP / XP 64 octets. Les technologies NVIDIA® Quad SLITM prennent en charge Windows® 7 / 7 64 octets / VistaTM / VistaTM 64 octets uniquement. Veuillez suivre les instructions d’installation de la page 19 pour plus de détails.
2.62.6
Mode d’emploi pour CrossFireXMode d’emploi pour CrossFireX
2.6
Mode d’emploi pour CrossFireX
2.62.6
Mode d’emploi pour CrossFireXMode d’emploi pour CrossFireX
TMTM
TM
CrossFireXCrossFireX
CrossFireX
CrossFireXCrossFireX
Cette carte mère prend en charge CrossFireXTM et Quad CrossFireXTM. La technologie CrossFireXTM offre le moyen le plus avantageux de combiner divers dispositifs de traitement graphique performants (GPU) dans un seul PC. Combinez une gamme de modes d’exploitation différents avec des logiciels intelligents et des mécanismes d’interconnexion innovants. CrossFireXTM permet d’obtenir le niveau de performance le plus haut possible et une haute qualité d’image pour les applications 3D. En général, CrossFireXTM est pris en charge par Windows® XP avec le Pack de service 2 / VistaTM / 7. Quad CrossFireXTM est pris en charge par Windows® VistaTM / 7 uniquement. Veuillez consulter le site d’AMD pour les mises à jour de driver ATITM CrossFireXTM. Veuillez suivre les instructions d’installation de la page 22 pour plus de détails.
2.7 “Surround Display”2.7 “Surround Display”
2.7 “Surround Display”
2.7 “Surround Display”2.7 “Surround Display”
Cette carte mère supporte la mise à niveau de Surround Display. Avec la carte externe d’extension VGA PCI Express, vous pouvez facilement jouir des avantages de la caractéristique de l’affichage Surround. Pour les instructions détaillées, veuillez vous reporter au document qui se trouve sur le chemin suivant dans le CD d’assistance : ..\ Surround Display Information
TMTM
TMTM
et Quad SLI et Quad SLI
et Quad SLI
et Quad SLI et Quad SLI
TMTM
TM
TMTM
TMTM
TM
TMTM
et Quad et Quad
et Quad
et Quad et Quad
TM
TM
ASRock X58 Extreme3 Motherboard
7777
77
7777
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 78
Français
FrançaisFrançais
FrançaisFrançais
2.8 Réglage des cavaliers2.8 Réglage des cavaliers
2.8 Réglage des cavaliers
2.8 Réglage des cavaliers2.8 Réglage des cavaliers
L’illustration explique le réglage des cavaliers. Quand un capuchon est placé sur les broches, le cavalier est « FERME ». Si aucun capuchon ne relie les broches,le cavalier est « OUVERT ». L’illustration montre un cavalier à 3 broches dont les broches 1 et 2 sont “FERMEES” quand le
Ferme Ouvert
capuchon est placé sur ces 2 broches.
Le cavalier Description
PS2_USB_PWR1 Court-circuitez les broches 2
(voir p.2 No. 1) et 3 pour choisir +5VSB
(standby) et permettre aux périphériques PS/2 ou USB de réveiller le système.
Note: Pour sélectionner +5VSB, il faut obligatoirement 2 Amp et un courant
standby supérieur fourni par l’alimentation.
Effacer la CMOS
(CLRCMOS1, le cavalier à 3 broches) (voir p.2 No. 15)
Paramètres par défaut
Effacer la CMOS
Note: CLRCMOS1 vous permet d’effa cer les données qui se trouvent da ns la CMOS.
Les données dans la CMOS comprennent les inf ormations de conf iguration du système telles que le mot de passe système, la date, l’heure et le s paramètres de configuration du système. Pour effa cer et réinitialiser le s paramètres du système pour retrouver la configuration par défaut, veuillez mettre l’ordinateur hors tension et débrancher le cordon d’alimentation de l’ali mentation éle ctrique. Attendez 15 secondes, puis utilisez un ca puchon de cavalier pour court­circuiter la broche 2 et la broche 3 sur CLRCMOS1 pendant 5 secondes. Après avoir court-circuité le cavalier Effacer la CMOS, veuillez enlever le capuchon de cavalier. Toutefois, veuillez ne pas effa cer la CMOS tout de suite après avoir mis le BIOS à jour. Si vous avez besoin d’eff a cer la CMOS lors que vous avez fini de mettre le BIOS à jour, vous devez d’abord initialiser le système, puis le mettre hors tension avant de procéder à l’opération d’effa ce ment de la CMOS.
7878
78
7878
Si vous effacez la CMOS, il se peut qu’une ouverture du boîtier soit détectée. Veuillez ajuster l’option du BIOS “Clear Status” (Effacer l’état) pour effacer la mention d’état d’intrusion dans le châssis.
ASRock X58 Extreme3 Motherboard
Page 79
2.9 En-têtes et Connecteurs sur Carte2.9 En-têtes et Connecteurs sur Carte
2.9 En-têtes et Connecteurs sur Carte
2.9 En-têtes et Connecteurs sur Carte2.9 En-têtes et Connecteurs sur Carte
Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers. NE PAS placer les capuchons de cavalier sur ces en-têtes et connecteurs. Le fait de placer les capuchons de cavalier sur les en­têtes et connecteurs causera à la carte mère des dommages irréversibles!
Connecteur du lecteur de disquette
(FLOPPY1 br. 33) (voir p.2 No. 31)
le côté avec fil rouge côté Broche1
Note: Assurez-vous que le côté avec fil rouge du câble est bien branché sur le
côté Broche1 du connecteur.
Connecteur IDE primaire (bleu)
(IDE1 br. 39, voir p.2 No. 14)
connecteur bleu connecteur noir vers la carte mère vers le disque dur
Câble ATA 66/100/133 80 conducteurs
Note: V euillez vous reporter aux instructions du fa brica nt de votre IDE périphérique
pour les détails.
Connecteurs Série A T AII Ces six connecteurs Série
(SATAII_1_2: AT AII (SA T AII) prennent en voir p.2 No. 16) charge les câbles SATA pour (SAT AII_3_4: les périphériques de stockage voir p.2 No. 17) internes. L’interface SATAII (SATAII_5_6: actuelle permet des taux voir p.2 No. 18) transferts de données pouvant
aller jusqu’à 3,0 Gb/s.
SAT AII_5_6 SA T AII_3_4 SA T AII_1_2
ASRock X58 Extreme3 Motherboard
7979
79
7979
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 80
Connecteurs Série ATA3 Ces deux connecteurs Série
(SAT A3_1: voir p.2 No. 13) ATA3 (SATA3) prennent en (SAT A3_2: voir p.2 No. 12) charge les câbles SATA pour
SAT A3_2
les périphériques de stockage
SAT A3_1
internes. L’interface SATA3 actuelle permet des taux transferts de données pouvant aller jusqu’à 6,0 Gb/s.
Câble de données Toute cote du cable de data SAT A Série ATA (SA TA) peut etre connecte au disque dur
(en option) SATA / SATAII / SATA3 ou au
connecteur SATAII / SATA3 sur la carte mere.
Cordon d’alimentation Veuillez connecter l’extrémité Série ATA (SA T A ) noire du cordon d’alimentation
(en option) SATA sur le connecteur
connecter au connecteur
d’alimentation du disque
dur SAT A
connecter à l’unité d’alimentation électrique
d’alimentation sur chaque unité. Connectez ensuite l’extrémité blanche du cordon d’alimentation SATA sur le connecteur d’alimentation de l’unité d’alimentation électrique.
En-tête USB 2.0 A côté des cinq ports
(US6_7 br.9) USB 2.0 par défaut sur le (voir p.2 No. 25) panneau E/S, il y a deux
embases USB 2.0 sur cette carte mère. Chaque embase USB 2.0 peut prendre en
(US8_9 br.9) charge 2 ports USB 2.0. (voir p.2 No. 10)
Français
FrançaisFrançais
FrançaisFrançais
8080
80
8080
Connecteur TPM
(TPM1 br. 19) (voir p.2 No. 29)
Ce connecteur prend en charge un système Trusted Platform Module (TPM ou module de plateforme de confiance), qui peut stocker des clés de sécurité, des certificats numériques, des mots de passe
ASRock X58 Extreme3 Motherboard
Page 81
et des données. Un système TPM permet également de renforcer la sécurité des réseaux, protège les identités numériques, et assure l’intégrité de la plate-forme.
En-tête du module infrarouge Cet en-tête supporte un module
(IR1 br.5) infrarouge optionnel de (voir p.2 No. 33) transfert et de réception sans
fil.
Embase d’intrusion châssis Cette carte-mère prend en
(CI1 br.2) charge la détection (voir p.2 No. 35) d’OUVERTURE DE BOÎTIER, qui
détecte tout retrait du capot du châssis. Cette fonction nécessite un châssis qui a été conçu pour la détection d’intrusion dans le châssis.
Connecteurs audio internes Ils vous permettent de gérer des
(CD1 br. 4) entrées audio à partir de sources (CD1: voir p.2 No. 43) stéréo comme un CD-ROM,
CD1
DVD-ROM, un tuner TV ou une carte MPEG.
prend en charge sted Platform
Connecteur audio panneau C’est une interface pour un câble av ant audio en façade qui permet le
(HD_AUDIO1 br. 9) bra nchement et le contrôle (voir p.2 No. 44) commodes de périphériques
audio.
1. L’audio à haute définition (HDA) prend en charge la détection de fiche, mais le fil de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de châssis afin installer votre système.
2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio du panneau avant conformément à la procédure ci-dessous : A. Connectez Mic_IN (MIC) à MIC2_L. B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L. C. Connectez Ground (GND) à Ground (GND). D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous n’avez pas besoin de les connecter pour le panneau audio AC’97.
ASRock X58 Extreme3 Motherboard
8181
81
8181
çaisçais
çaisçais
çais
ranran
ranran
ran FF
FF
F
Page 82
E. Entrer dans l’utilitaire de configuration du BIOS. Saisir les Paramètres avancés puis sélectionner Configuration du jeu de puces. Définir l’option panneau de commande de [Auto] à [Activé].
En-tête du panneau système Cet en-tête permet d’utiliser
(PANEL1 br.9) plusieurs fonctions du (voir p.2 No. 9) panneau système frontal.
En-tête du haut-parleur Veuillez connecter le de châssis haut-parleur de châssis sur
(SPEAKER1 br. 4) cet en-tête. (voir p.2 No. 21)
LED di accensione Collegare il LED di a ccen sione
(3-pin PLED1) chassi per indicare lo stato di (vedi p.2 Nr. 20) alimentazione del sistema. Il
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggi are in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
Français
FrançaisFrançais
FrançaisFrançais
8282
82
8282
Connecteur pour châssis, NB et ventilateur
(CHA_FAN1 br. 4) (voir p.2 No. 28)
(CHA_FAN2 br. 3) (voir p.2 No. 6)
(NB_FAN1 br. 3) (voir p.2 No. 42)
(PWR_FAN1 br. 3) (voir p.2 No. 5)
ASRock X58 Extreme3 Motherboard
Branchez les câbles du ventilateur aux connecteurs pour ventilateur et faites correspondre le fil noir à la broche de terre.
Page 83
Connecteur du ventilateur Veuillez connecter le câble de de l’UC ventilateur d’UC sur ce
(CPU_FAN1 br. 4) connecteur et brancher le fil (voir p.2 No. 2) noir sur la broche de terre.
ien que cette carte mère offre un support de (Ventilateur silencieux) ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut bien fonctionner même sans la fonction de commande de vitesse du ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3 broches au connecteur du ventilateur de CPU sur cette carte mère, veuillez le connecter aux broches 1-3.
Installation de ventilateur à 3 broches
4 3 2 1
Broches 1-3 connectées
onnecteurs pour es correspondre
En-tête d’alimentation ATX Veuillez connecter l’unité
(ATXPWR1 br. 24) d’alimentation A TX sur cet en- (voir p.2 No. 8) tête.
Bien que cette carte mère fournisse un connecteur de
12 124
13
12
courant ATX 24 broches, elle peut encore fonctionner si vous adopter une alimentation traditionnelle ATX 20 broches. Pour utiliser une alimentation ATX 20 broches, branchez à l’alimentation électrique ainsi qu’aux broches 1 et 13.
20-Installation de l’alimentation électrique A TX
Connecteur ATX 12V Veuillez connecter une unité
(ATX12V1 br .8) d’alimentation électrique ATX (voir p.2 No. 3) 12V sur ce connecteur.
8 5
4 1
1
Bien que cette carte mère possède 8 broches connecteur d’alimentation ATX 12V, il peut toujours travailler si vous adoptez une approche traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser l’alimentation des 4 broches ATX, branchez votre alimentation avec la broche 1 et la broche 5.
4-Installation d’alimentation à 4 broches A TX 12V
8 5
4 1
Header de IEEE 1394 Sauf un port de default IEEE
(FRONT_1394 br. 9) 1394 sur le panel I/O, il y a un (voir p.2 No. 27) header de IEEE1394
(FRONT_1394) sur cette carte mere. Le header de IEEE 1394 peut supporter un port de IEEE
1394.
ASRock X58 Extreme3 Motherboard
24
13
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
8383
83
8383
Page 84
En-tête de port COM Cette en-tête de port COM est
(COM1 br.9) utilisée pour prendre en charge (voir p.2 No. 30) un module de port COM.
Connecteur HDMI_SPDIF Connecteur HDMI_SPDIF,
(HDMI_SPDIF1 3-pin) fournissa nt une sortie audio (voir p.2 No. 32) SPDIF vers la carte V GA HDMI,
et permettant au système de se connecter au un téléviseur numérique HDMI /un projecteur / un périphérique LCD. Veuillez brancher le connecteur HDMI_SPDIF de la carte V GA HDMI sur ce connecteur.
Français
FrançaisFrançais
FrançaisFrançais
Câble HDMI_SPDIF Veuillez connecter l’extrémité
(en option) noire (A) du câble HDMI_SPDIF
C
B
A
au collecteur HDMI_SPDIF de la carte-mère. Connectez ensuite l’extrémité blanche (B ou C) du câble HDMI_SPDIF au connecteur HDMI_SPDIF de la carte VGA HDMI.
A. extrémité noire B. extrémité blanche C. extrémité blanche (2 briches) (3 briches)
8484
84
8484
ASRock X58 Extreme3 Motherboard
Page 85
2.10 Interrupteur rapides2.10 Interrupteur rapides
2.10 Interrupteur rapides
2.10 Interrupteur rapides2.10 Interrupteur rapides
Cette carte mère dispose de trois interrupteurs rapides : un interrupteur d’alimentation, un interrupteur de réinitialisation et un interrupteur d’effacement de CMOS, permettant aux utilisateurs de rapidement allumer/éteindre ou réinitialiser le système, ainsi que d’effacer les valeurs du CMOS.
Interrupteur d’alimentation
(PWRBTN) (voir p.2 No. 24)
Interrupteur de réinitialisation
(RSTBTN) (voir p.2 No. 23)
Interrupteur d’effacement de CMOS
(CLRCBTN) (voir p.2 No. 17)
Vous n’êtes pas autorisé à utiliser la fonction de l’interrupteur Clear CMOS (Effacement du CMOS) si vous configurez un mot de passe pour le système. Si vous voulez effacer les valeurs du CMOS, veuillez d’abord effacer le mot de passe de votre système ou vous référer plutôt à la description “Clear CMOS jumper (Cavalier d’effacement du CMOS)” de la page 78.
RESET
clr
CMOS
L’interrupteur d’alimentation est un interrupteur rapide, qui permet à l’utilisateur d’allumer/éteindre rapidement le système.
L’interrupteur de réinitialisation est un interrupteur rapide, qui permet à l’utilisateur de réinitialiser ra pide ment le système.
L’interrupteur d’effacement de CMOS est un interrupteur rapide qui permet à l’utilisateur d’effacer rapidement les valeurs du CMOS.
ASRock X58 Extreme3 Motherboard
8585
85
8585
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 86
2.112.11
LED de débogageLED de débogage
2.11
LED de débogage
2.112.11
LED de débogageLED de débogage
La LED de débogage intégrée sert à fournir des informations de code, ce qui rend le dépannage encore plus facile. Veuillez consulter les diagrammes des pages 33, 34 et 35 pour la lecture des codes LED de débogage.
2.122.12
Guide d’installation des pilotesGuide d’installation des pilotes
2.12
Guide d’installation des pilotes
2.122.12
Guide d’installation des pilotesGuide d’installation des pilotes
Pour installer les pilotes sur votre système, veuillez d’abord insérer le CD dans votre lecteur optique. Puis, les pilotes compatibles avec votre système peuvent être détectés automatiquement et sont listés sur la page du pilote du CD. V euillez suivre l’ordre de haut en bas sur le côté pour installer le s pilote s requis. En conséquence, les pilotes que vous installez peuvent fonctionner correctement.
Français
FrançaisFrançais
FrançaisFrançais
2.13 Installation de Windows2.13 Installation de Windows
2.13 Installation de Windows
2.13 Installation de Windows2.13 Installation de Windows
TMTM
TM
Vista Vista
Vista
Vista Vista
Si vous souhaitez installer Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OS sur votre lecteur de disque dur SATA / SATAII avec les fonctions RAID, veuillez vous référer au document de l’étape suivante sur le CD de support pour connaître la procédure détaillée:
..\ RAID Installation Guide (Guide d’installation RAID)
2.142.14
Installation de Windows Installation de Windows
2.14
Installation de Windows
2.142.14
Installation de Windows Installation de Windows Vista Vista
Vista
Vista Vista
Si vous voulez installer Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bits / XP / XP 64-bit sur vos disques durs SATA / SATAII sans les fonctions RAID, veuillez suivre les procédures ci-dessous, en fonction de l’OS que vous installez.
2.14.1 Installation de Windows2.14.1 Installation de Windows
2.14.1 Installation de Windows
2.14.1 Installation de Windows2.14.1 Installation de Windows fonctions RAID fonctions RAID
fonctions RAID
fonctions RAID fonctions RAID
Si vous voulez installer Windows® XP / XP 64-bit sur vos disques durs SATA / SATAII sans les fonctions RAID, veuillez suivre la procédure ci-dessous.
Utilisation des disques durs SATA / SATAII sans NCQ fonctions
ETAPE 1 : Configurez le BIOS.
A. Accédez à BIOS SETUP UTILITY (Utilitaire de configuration BIOS) écran Avancé Configuration Storage. B. Réglez «configuration SA TAII « sur [Améliorée], et puis dans l’option «Configurer
SATAII comme «, veuillez régler sur [IDE].
ETAPE 2 : Installez le système d’exploitation Windows® XP / XP 64 bits
sur votre système.
TMTM
64-bit / XP / XP 64-bit avec fonctions RAID 64-bit / XP / XP 64-bit avec fonctions RAID
64-bit / XP / XP 64-bit avec fonctions RAID
64-bit / XP / XP 64-bit avec fonctions RAID 64-bit / XP / XP 64-bit avec fonctions RAID
TMTM
TM
TMTM
64-bit / XP / XP 64-bit sans fonctions RAID 64-bit / XP / XP 64-bit sans fonctions RAID
64-bit / XP / XP 64-bit sans fonctions RAID
64-bit / XP / XP 64-bit sans fonctions RAID 64-bit / XP / XP 64-bit sans fonctions RAID
®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
®®
®
®®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
®
XP / XP 64-bit sans XP / XP 64-bit sans
XP / XP 64-bit sans
XP / XP 64-bit sans XP / XP 64-bit sans
TMTM
TM
TMTM
/ /
/
/ /
TMTM
TM
TMTM
/ /
/
/ /
8686
86
8686
ASRock X58 Extreme3 Motherboard
Page 87
TMTM
TM
2.14.2 Installation de Windows2.14.2 Installation de Windows
2.14.2 Installation de Windows
2.14.2 Installation de Windows2.14.2 Installation de Windows
TMTM
TM
TMTM
VistaVista
Vista
VistaVista
Si vous voulez installer Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit sur vos disques durs SATA / SATAII sans les fonctions RAID, veuillez suivre la procédure ci-dessous.
Utilisation des disques durs SAT A / SATAII sa n s NCQ fonction s
ETAPE 1 : Configurez le BIOS.
A. Accédez à BIOS SETUP UTILITY (Utilitaire de configuration BIOS) écran Avancé Configuration Storage. B. Réglez «configuration SATAII « sur [Améliorée], et puis dans l’option «Conf igurer
SATAII comme «, veuillez régler sur [IDE].
ETAPE 2: Installer le système d’exploitation Windows® 7 / 7 64-bit / Vista
/ Vista
Utilisation des disques durs SATA / SATAII avec NCQ fonctions ETAPE 1 : Configurez le BIOS.
A. Accédez à BIOS SETUP UTILITY (Utilitaire de configuration BIOS) écran Avancé Configuration Storage. B. Réglez «configuration SATAII « sur [Améliorée], et puis dans l’option «Conf igurer
SATAII comme «, veuillez régler sur [AHCI].
ETAPE 2: Installer le système d’exploitation Windows® 7 / 7 64-bit / Vista
/ Vista
64-bit sans fonctions RAID 64-bit sans fonctions RAID
64-bit sans fonctions RAID
64-bit sans fonctions RAID 64-bit sans fonctions RAID
TM
64-bit sur votre système.
TM
64-bit sur votre système.
®
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
7 / 7 64-bit / Vista
7 / 7 64-bit / Vista 7 / 7 64-bit / Vista
TMTM
/ /
/
/ /
TM
TM
ASRock X58 Extreme3 Motherboard
8787
87
8787
çaisçais
çaisçais
çais
FranFran
FranFran
Fran
Page 88
3. Informations sur le BIOS
La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous démarrez l’ordinateur, veuillez presser <F2> pendant le POST (Power-On-Self­Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier du système. Vous pouvez également redémarrer en éteignant le système et en le rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un programme piloté par menu, qui vous permet de faire défiler par ses divers sous-menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées sur le BIOS, veuillez consulter le Guide de l’utilisateur (fichier PDF) dans le CD technique.
4. Informations sur le CD de support4. Informations sur le CD de support
4. Informations sur le CD de support
4. Informations sur le CD de support4. Informations sur le CD de support
Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®: 7 / 7 64 bits / VistaTM / Vista cette carte mère contient les pilotes et les utilitaires nécessaires pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu principal s’affiche automatiquement si “AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas automatiquement, localisez dans le CD technique le fichier “ASSETUP.EXE” dans le dossier BIN et double-cliquez dessus pour afficher les menus.
TM
64 bits / XP / XP 64 bits. Le CD technique livré avec
Français
FrançaisFrançais
FrançaisFrançais
8888
88
8888
ASRock X58 Extreme3 Motherboard
Page 89
1. Introduzione
Grazie per aver scelto una scheda madre ASRock X58 Extreme3, una scheda madre affidabile prodotta secondo i severi criteri di qualità ASRock. Le prestazioni eccellenti e il design robusto si conformano all’impegno di ASRock nella ricerca della qualità e della resistenza. Questa Guida Ra pida all’In stallazione contiene l’introduzione alla motherboard e la guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si possono trovare nel manuale per l’utente presente nel CD di supporto.
Le specifiche della scheda madre e il software del BIOS possono essere aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia modificato, la versione aggiornata sarà disponibile sul sito di ASRock senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate. ASRock website http://www.asrock.com Se si necessita dell’assistenza tecnica per questa scheda madre, visitare il nostro sito per informazioni specifiche sul modello che si sta usando. www.asrock.com/support/index.asp
1.1 Contenuto della confezione1.1 Contenuto della confezione
1.1 Contenuto della confezione
1.1 Contenuto della confezione1.1 Contenuto della confezione
Scheda madre ASRock X58 Extreme3
(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm) Guida di installazione rapida ASRock X58 Extreme3 CD di supporto ASRock X58 Extreme3 Un cavo IDE 80-pin Ultra A T A 66/100/133 Un cavo per floppy drive a 1,44 Mb Quattro cavi dati Serial AT A (SATA) (opzion ali) Due cavi di alimentazione HDD Seri al AT A (SATA) (opzion ali) Un I/O Shield Un Scheda ASRock SLI_Bridge_2S
ASRock X58 Extreme3 Motherboard
8989
89
8989
ItalianoItaliano
ItalianoItaliano
Italiano
Page 90
Italiano
ItalianoItaliano
ItalianoItaliano
1.21.2
SpecificheSpecifiche
1.2
Specifiche
1.21.2
SpecificheSpecifiche
Piattaforma - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm
- Design condensatore compatto (conden satori a conduttore in polimero di alta qualità realizzati al 100% in Gi appone)
Processore - Processore Intel® Socket 1366 CoreTM i7 Extreme Edition /
CoreTM i7 con supporto della tecnologia Intel® Dyna mic Speed
- Bus di sistema fino a 6400 MT/s; Intel® QuickPath Interconnect
- Struttura di fase con alimentazione V8 avanzata
- Supporto tecnologia Hyper Threading (vedi ATTENZIONE 1)
- Supporta la tecnologia overclocking “slegata” (vedi ATTENZIONE 2)
- Supporto CPU EM64T
Chipset - Northbridge: Intel® X58
- Southbridge: Intel® ICH10R
Memoria - Tecnologia memori a DDR3 a tre ca nali (vedi A TTENZIONE 3)
- 6 x slot DDR3 DIMM
- Supporto DDR3 2000(OC)/1866(OC)/1600(OC)/1333(OC)/ 1066 non-ECC, momoria senza buffer
- Supporto di DDR3 ECC, momoria senza buffer con processori Intel® Workstation 1S Xeon® serie 3500
- Capacità massima della memoria di sistema: 24GB (vedi ATTENZIONE 4)
- Supporto di Intel® XMP (Extreme Memory Profile) Slot di - 2 x slot PCI Express 2.0 x16 (Blu a modalità x16) espansione - 1 x slot PCI Express x16 (bianco a modalità x4)
(Spazio di ampiezza doppia tra gli alloggi PCI-E)
- 1 x slot PCI Express x1
- 2 x slot PCI
- Supporto di ATITM CrossFireXTM e Quad CrossFireX
- Supporto di NVIDIA® SLITM e Quad SLI Audio - 7.1 CH Windows® VistaTM Premium Level HD Audio con protezioni
contenuti
- DAC con raggio dinamico di 1 10dB (VIA® VT2020 Audio Codec)
- Supporto audio Blu-ray Premium LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL81 11DL
- Supporta Wake-On-LAN Pannello I/O Panel posteriore I/O - 1 x porta PS/2 per mouse
- 1 x porta PS/2 per tastiera
TM
TM
9090
90
9090
ASRock X58 Extreme3 Motherboard
Page 91
- 1 x Porta coassiale SPDIF Out
- 1 x Porta ottica SPDIF Out
- 5 x porte USB 2.0 già integrate
- 1 x Connettore alimentato eSA TAIII/USB 2.0
- 2 x porte USB 3.0 già integrate
- 1 x porte LAN RJ-45 con LED (LED azione/collega mento e LED velocità)
- 1 x porte IEEE 1394
- 1 x interruttore di pulizia CMOS
- Connettore HD Audio: cassa laterale / cassa posteriore / cassa centrale / bassi / ingresso line a / cassa frontale / microfono (vedi ATTENZIONE 5)
SATA3 - 2 x Connettori SATA3 6,0Gb/s SE9128 Marvell, supporto RAID
hardware (RAID 0 e RAID 1) e delle funzioni NCQ, AHCI e “Hot Plug” (il connettore SATA3_2 è condiviso con la porta eSATA3)
USB 3.0 - 2 x Porte USB3.0 UPD720200 NEC, supporto di USB 1.0/2.0/3.0
fino a 5Gb/s
Connettori - 6 x connettori SATAII 3.0Go/s, sopporta RAID (RAID 0, RAID 1,
RAID 10, RAID 5 ed Intel M atrix Storage), NCQ, AHCI e “Collegamento a caldo”
- 2 x connettori SATA3 6.0Go/s
- 1 x connettori ATA133 IDE (supporta fino a 2 dispositivi IDE)
- 1 x porta Floppy
- 1 x Collettore modulo infrarossi
- 1 x collettore porta COM
- 1 x connettore HDMI_SPDIF
- 1 x collettore IEEE 1394
- 1 x collettore TPM
- 1 x header di intrusione dello chassis
- 1 x LED di accensione
- Connettore CPU/Chassis/NB/Alimentazione ventola
- 24-pin collettore alimentazione ATX
- 8-pin connettore ATX 12V
- Connettori audio interni
- Connettore audio sul pannello frontale
- 2 x Collettore USB 2.0 (supporta 4 porte USB 2.0)
(vedi ATTENZIONE 6)
- 1 x Dr. Debug (LED debug con 7 segmenti) Interruttore - 1 x interruttore pulizia CMOS con LED rapido - 1 x interruttore di alimentazione con LED
- 1 x interruttore di reset con LED
BIOS - 8Mb AMI BIOS
ASRock X58 Extreme3 Motherboard
9191
91
9191
ItalianoItaliano
ItalianoItaliano
Italiano
Page 92
Italiano
ItalianoItaliano
ItalianoItaliano
9292
92
9292
- Suppor AMI legal BIOS
- Supporta “Plug and Play”
- Compatibile con ACPI 1.1 wake up events
- Supporta jumperfree
- Supporta SMBIOS 2.3.1
- Regolazione multi-voltaggio CPU, VCCM, IOH, ICH, VTT, IOH/ICH PCIE, CPU PLL, IOH CSI, VCORE
- Supporto I. O. T. (Intelligent Overclocking Technology) CD di - Driver, utilità, software antivirus (Versione dimostrativa), Suite supporto software ASRock (Suite CyberLink DVD e Creative Sound
Blaster X-Fi MB) (OEM e Versione demo) Caratteristica - Sintonizzatore ASRock OC (vedi ATTENZIONE 7) speciale - Intelligent Energy Saver (Risparmio intelligente dell’energia)
(vedi ATTENZIONE 8)
- Instant Boot
- ASRock Instant Flash (vedi ATTENZIONE 9)
- ASRock OC DNA (vedi ATTENZIONE 10)
- Booster ibrido:
- Stepless control per frequenza del processore (vedi ATTENZIONE 11)
- ASRock U-COP (vedi ATTENZIONE 12)
- Boot Failure Guard (B.F.G.)
- LED notturno Monitoraggio - Sensore per la temperatura del processore Hardware - Sensore temperatura scheda madre
- Indicatore di velocità per la ventola del CPU/Chassis/NB/
Alimentazione
- Ventola CPU silenziosa
- Ventola CPU/chassis con controllo di varie velocità
- Rilevamento CASE APER TO
- Voltaggio: +12V, +5V, +3.3V, Vcore Compatibi- - Microsoft® Windows® 7 / 7 64 bit / VistaTM / Vista
TM
64 bit / XP /
lità SO XP 64 bit Certificazioni - FCC, CE, WHQL
- Predisposto ErP/EuP (è necessaria l’alimentazione predisposta
per il sistema ErP/EuP) (vedi A TTENZIONE 13)
* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com
AVVISO
Si prega di prendere atto che la procedura di overclocking implica dei rischi, come anche la regolazione delle impostazioni del BIOS, l’a pplicazione della tecnologia U ntied Overclocking Technology, oppure l’uso di strumenti di overclocking forniti da terzi. L’overclocking può influenzare la stabilità del sistema, ed anche provocare danni ai componenti ed alle periferiche del sistema. La procedura è eseguita a proprio rischio ed a proprie spese. Noi non possiamo essere ritenuti responsabili per possibili danni provocati dall’overclocking.
ASRock X58 Extreme3 Motherboard
Page 93
ATTENZIONE!
1. Per il settaggio della “Tecnologia Hyper-Threading”, per favore controllare pagina 62 del Manuale dell’utente all’interno del CD di supporto.
2. Questa scheda madre supporta la tecnologia overclocking “slegata”. Per i dettagli leggere “Tecnologia di Untied Overclocking” a pagina 37.
3. Questa scheda madre supporta la tecnologia Triple Channel Memory. Prima di implementare la te cnologia Triple Channel Memory, assicurarsi di leggere la guida all’installazione dei moduli di memoria, a pagina 98, per
seguire un’installazione appropri ata.
4. A causa delle limitazioni del sistema operativo, le dimensioni effettive della memoria possono essere inferiori a 4GB per l’accantonamento riservato all’uso del sistema sotto Windows Windows® OS con CPU 64-bit, non c’è tale limitazione.
5. Questa scheda madre supporta l’ingresso stereo e mono per il microfono. Questa scheda madre supporta le modalità 2 canali, 4 canali, 6 canali e 8 canali per l’uscita audio. Controllare la tavola a pagina 3 per eseguire il collegamento appropriato.
6. La Gestione Risorse per USB 2.0 funziona perfettamente con Microsoft Windows® 7 64-bit / 7 / VistaTM 64-bit / VistaTM / XP 64 bit / XP SP1; SP2.
7. Si tratta di uno strumento di sicronizzazione ASRock di face uso in grado di implementare il controllo del sistema tramite la funzione di hardware monitor e sincronizzare le Vostre unita‘ hardware per ottenere la migliore prestazione in Windows?. Prego visitare il nostro sito Internet per ulteriori dettagli circa l‘uso del Sintonizzatore ASRock OC. ASRock website: http://www.asrock.com
8. Dotato di un design avanzato e brevettato dell’hardware e del software, Intelligent Energy Saver è una tecnologia rivoluzionaria che offre un risparmio energetico senza pari. In altre parole: è capace di fornire un risparmio energetico eccezionale e di migliorare l’efficienza senza sacrificare le prestazioni di computazione. Visitare il nostro sito per informazioni sulle procedure operative di Intelligent Energy Saver. Sito ASRock: http://www.asrock.com/feature/IES/index.html
9. ASRock Instant Flash è una utilità Flash BIOS integrata nella Flash ROM. Questo comodo strumento d’aggiornamento del BIOS permette di aggiornare il sistema BIOS senza accedere a sistemi operativi come MS­DOS or Windows®. Con questa utilità, si può premere il tasto <F6> durante il POST, oppure il tasto <F2> nel menu BIOS per accedere ad ASRock Instant Flash. Avviare questo strumento e salvare il nuovo file BIOS nell’unità Flash USB, dischetto (disco floppy) o disco rigido; poi si può aggiornare il BIOS con pochi clic, senza preparare altri dischetti (dischi floppy) o altre complicate utilità Flash. Si prega di notare che l’unità Flash USB o il disco rigido devono usare il File System FAT32/16/
12.
10. Il nome stesso del software – OC DNA – dice di cosa è capace. OC DNA, una utilità esclusiva sviluppata da ASRock, fornisce un modo comodo per registrare le impostazioni OC e condividerle con gli altri. Aiuta a salvare le registrazioni di overclocking nel sistema operativo e semplifica la complicata procedura di registrazione delle impostazioni di
ASRock X58 Extreme3 Motherboard
®
7 / VistaTM / XP. Per
®
ItalianoItaliano
ItalianoItaliano
Italiano
9393
93
9393
Page 94
overclocking. Con OC DNA, puoi salvare le impostazioni OC come un profilo da condividere con gli amici! I tuoi amici possono scaricare il profilo OC sul loro sistema operativo per ottenere le tue stesse impostazioni OC! Si prega di notare che il profilo OC può essere condiviso e modificato solo sulla stessa scheda madre.
11. Anche se questa motherboard offre il controllo stepless, non si consiglia
di effettuare l’overclocking. Frequenze del bus del processore diverse da quelle raccomandate possono causare instabilità al sistema o danni al processore e alla scheda madre.
12. Se il processore si surriscalda, il sistema si chiude automaticamente.
Prima di riavviare il sistema, assicurarsi che la ventolina CPU della scheda madre funzioni correttamente; scollegare e ricollegare il cavo d’alimentazione. Per migliorare la dissipazione del calore, ricordare di applicare l’apposita pasta siliconica tra il processore e il dissipatore quando si installa il sistema.
13. EuP, che sta per Energy Using Product (Prodotto che consuma energia)
, era una normativa emanata dall’Unione Europea che definiva il consumo energetico del sistema completo. In base all’EuP, l’alimentazione totale del sistema completo deve essere inferiore a 1,00 W quando è spento. Per soddisfare la norma EuP sono necessari un alimentatore e una scheda elettrica predisposti EuP. In base ai suggerimenti Intel l’alimentatore predisposto EuP deve soddisfare lo standard secondo cui l’efficienza energetica in standby di 5 v è più alta del 50% con un consumo di corrente di 100 mA. Per la scelta di un’alimentatore predisposto EuP consigliamo di verificare ulteriori dettagli con il produttore.
Italiano
ItalianoItaliano
ItalianoItaliano
9494
94
9494
2. Installazione2. Installazione
2. Installazione
2. Installazione2. Installazione
Precauzioni preinstallazionePrecauzioni preinstallazione
Precauzioni preinstallazione
Precauzioni preinstallazionePrecauzioni preinstallazione
Leggere le seguenti precauzioni prima di installare componenti delle schede madri o di ca mbi are le i mpostazioni delle schede ma dri.
1. T ogliere il cavo dalla presa elettrica pri ma di toccare le componenti. In caso contrario la schedamadre, le periferiche, e/o i componenti possono subire gravi danni.
2. Per evitare che l’elettricità statica danneggi la scheda madre,NON appoggi are la scheda ma dre su moquette, tappeti o tessuti simili. Ricordarsi di indossare un braccialetto antistatico collegato a terra o di toccare un oggetto posizionato a terra prima di ma neggiare le componenti.
3. T enere i componenti per i bordi e non toccare i ICs.
4. Ogni volta che si disinstalla un componente, appoggi arlo su un tappetino antistatico messo a terra o depositarlo nella borsa data in dotazione con il componente.
ASRock X58 Extreme3 Motherboard
Page 95
5. Nell’usare i giraviti per fissare la scheda madre al telaio non serrare eccessivamente le viti! Altrimenti si rischia di danneggiare la scheda madre.
2.1 Installazione del processore2.1 Installazione del processore
2.1 Installazione del processore
2.1 Installazione del processore2.1 Installazione del processore
Attenersi alle seguenti fasi per installare la CPU Intel 1366-Pin.
Prima da inserire la CPU da 1366-Pin nel socket, verificare che la superficie della CPU sia pulita e che non ci siano pin piegati nel socket. Non forzare l’inserimento della CPU nel socket se ci sono pin piegati. In caso contrario la CPU potrebbe essere seriamente danneggiata.
(Piastra di carica mento)
(Disposizione comandi)
Vista del socket 1366-Pin
Fase 1. Aprire la presa:
Fase 1-1. Sbloccare la leva premendola
verso il basso ed allontanandola dal gancio per liberare la linguetta.
(Corpo socket)
Fase 1-2. Ruotare di circa 135 gradi la leva
di carico per aprirla completamente.
Fase 1-3. Ruotare di circa 100 gradi la
piastra di carico per aprirla completamente.
Fase 2. Rimuovere il cappuccio PnP
(Pick and Pla ce: prelievo e posizionamento).
1. Si raccomanda di utilizzare la linguetta del cappuccio per la manipolazione ed evitare di far saltare via il cappuccio PnP.
2. Questo tappo deve essere inserito se se la scheda madre deve essere restituita per l’assistenza.
ASRock X58 Extreme3 Motherboard
9595
95
9595
ItalianoItaliano
ItalianoItaliano
Italiano
Page 96
Fase 3. Inserire la CPU 1366-Pin:
Fase 3-1. Tenere la CPU dai bordi segnati
con linee nere.
Fase 3-2. Orientare il pacchetto con l’IHS
(Integrated Heat Sink: dispersore di calore integrato) verso l’alto. Individuare il Pin1 ed i due dentelli chiave d’orientamento.
Dente di orientamento
Pin1
Dente di orientamento
CPU da 1366-Pin
Per il corretto inserimento, verificare di far combaciare i due denti di allineamento della CPU con le due tacche nel socket.
Fase 3-3. Collocare con delicatezza la CPU
sulla presa con un movimento puramente verticale.
Fase 3-4. Verificare che la CPU sia all’interno
della presa e combaci in modo appropri ato con le chiavi d’orientamento.
Ta cca di allinea mento
Pin1
T acca di allinea mento
Socket da 1366-Pin
Linea nera
Linea nera
Italiano
ItalianoItaliano
ItalianoItaliano
9696
96
9696
Fase 4. Chiudere la presa:
Fase 4-1. Ruotare la piastra di carico
sull’IHS.
Fase 4-2. Bloccare la leva di carico mentre
si preme leggermente sulla piastra di carico.
Fase 4-3. Fissare la leva di carico con la
linguetta della pia stra di carico che si trova sulla parte inferiore della linguetta di ritenzione della leva di carico.
ASRock X58 Extreme3 Motherboard
Page 97
2.22.2
Installazione della ventola e del dissipatore diInstallazione della ventola e del dissipatore di
2.2
Installazione della ventola e del dissipatore di
2.22.2
Installazione della ventola e del dissipatore diInstallazione della ventola e del dissipatore di calore della CPUcalore della CPU
calore della CPU
calore della CPUcalore della CPU
Per eseguire correttamente l’installazione si rimanda ai manuali di istruzione della ventola e del dissipatore di calore della CPU.
Di seguito viene presentato un esempio che mostra l’installazione del dissipatore per la CPU da 1366-Pin.
Fase1. Applicare il materiale di interfaccia termica al
dell’IHS sulla superficie del socket
(Applicare il materiale dell’interfaccia termica)
Fase 2. Collocare il dissipatore di calore nel socket.
Verificare che i cavi della ventola sono orientati sul lato più vicino al connettore della ventola della CPU presente sulla scheda madre (CPU_F AN1, si veda pagin a 2, No. 2).
Fase 3. Allineare i fastener con i fori passanti della
scheda madre.
Fase 4. Ruotare i fastener in senso orario, quindi
premere il cappuccio del fastener con il pollice per installarlo e fissarlo. Ripetere la stessa operazione con gli altri fa stener.
Se si premono i fastener verso il basso, senza ruotarli in senso orario, il dissipatore non viene fissato bene alla scheda madre
Fase 5. Collegare il cavo di alimentazione della
ventola al connettore ventola della CPU sulla scheda madre.
Fase 6. fissare il cavo in eccesso con fascette per
assicurare che il cavo non interferisca con il funzionamento della ventola o che venga a contatto con gli altri componenti.
(Cavi della ventola sul lato più vicino all’header della MB)
(Fori per fastener che allineati ad fori passa nti)
(Premere verso il basso (4 punti))
ItalianoItaliano
ItalianoItaliano
Italiano
ASRock X58 Extreme3 Motherboard
9797
97
9797
Page 98
Italiano
ItalianoItaliano
ItalianoItaliano
2.3 Installazione dei moduli di memoria (DIMM)2.3 Installazione dei moduli di memoria (DIMM)
2.3 Installazione dei moduli di memoria (DIMM)
2.3 Installazione dei moduli di memoria (DIMM)2.3 Installazione dei moduli di memoria (DIMM)
Questa scheda madre fornisce sei alloggi DIMM DDR3 (Double Data Rate 3) a 240 pin, e supporta la tecnologia Tri ple Channel Memory. Per la conf igurazione a tre canali, è necessario installare se mpre coppie identiche (ste ssa marca, velocità, dimensioni e tipo di chip) di DIMM DDR3 negli alloggi amenti dello stesso colore. In altre parole, è necessario installare coppie identiche di DIMM DDR3 nel canale doppio (DDR3_A1, DD R3_B1 e DDR3_C1; alloggiamenti bianco; vedere pag. 2 Nr. 7) oppure coppie identiche di DIMM DD R3 nel canale doppio (DDR3_A2, DD R3_B2 e DDR3_C2; alloggiamenti blu; vedere pag. 2 Nr. 11), per fare sì che la tecnologia Triple Channel Memory possa essere attivata. Questa scheda madre consente anche di installare sei DIMM DDR3 per la configurazione a canale doppio.Questa scheda madre consente anche di installare sei DIMM DDR3 per configurazione a canale triple, si raccomanda di installare DIMM DDR3 identiche nei sei alloggi amenti.
Configurazioni raccomandate della memoria
DDR3_A2 DDR3_A1 DD R3_B2 DDR3_B1 DD R3_C2 DDR3_C1
(Blu) (Bianco) (Blu) (Bianco) (Blu) (Bianco) 1 DIMM - Popolato - - - ­ 2 DIMMs - Popolato - Popolato - ­ 3 DIMMs - Popolato - Popolato - Popolato 4 DIMMs Popolato Popolato - Popolato - Popolato 5 DIMMs Popolato Popolato Popolato Popolato - Popolato 6 DIMMs Popolato Popolato Popolato Popolato Popolato Popolato
1. Installare il modulo di memoria nell’alloggio bianco (DDR3_A1, DDR3_B1 o DDR3_C1) per la prima priorità.
2. A causa delle definizioni delle specifiche della CPU Intel®, il sistema no si avvierà se nell’alloggio DDR3_A2, DDR3_B2 o DDR3_C2 è installato un solo modulo DIMM.
3. A causa delle definizioni delle specifiche della CPU Intel®, i moduli DIMM XMP e DDR3 1600 sono supportati su un solo DIMM per canale.
4. Nel Canale A, Canale B e Canale C si possono installare memorie con dimensioni diverse. Il sistema mappa le dimensioni totali del canale di dimensioni minori per la configurazione a due o tre canali. Tutta la memoria in eccesso dei canali con dimensioni maggiori è quindi mappata per le operazioni a canale singolo.
5. Non è consentito di installare un modulo di memoria DDR o DDR2 in un alloggio DDR3; diversamente questa scheda madre ed il modulo DIMM potrebbero essere danneggiati.
9898
98
9898
ASRock X58 Extreme3 Motherboard
Page 99
Installare una DIMMInstallare una DIMM
Installare una DIMM
Installare una DIMMInstallare una DIMM
Scollegare l’alimentazione elettrica prima di aggiungere o rimuovere i DIMM o altri componenti del sistema.
Step 1. Sbloccare lo slot DIMM premendo i fermi che lo trattengono verso
l’esterno.
Step 2. Allineare una DIMM sullo slot così che il pettine della DIMM combaci con
la sua sede sullo slot.
La DIMM può essere montata correttamente soltanto con un orientamento. Se si dovesse installare a forza la DIMM nello slot con un orientamento errato, si causerebbero danni permanenti alla scheda madre e alla DIMM stessa.
Step 3. Inserire saldamente la DIMM nello slot f ino a far scattare completamente
in posizione i fermagli di ritegno alle due estremità e fino ad installare correttamente la DIMM nella sua sede.
ASRock X58 Extreme3 Motherboard
9999
99
9999
ItalianoItaliano
ItalianoItaliano
Italiano
Page 100
Italiano
ItalianoItaliano
ItalianoItaliano
2.42.4
Slot di espansione (Slot PCI ed Slot PCI Express)Slot di espansione (Slot PCI ed Slot PCI Express)
2.4
Slot di espansione (Slot PCI ed Slot PCI Express)
2.42.4
Slot di espansione (Slot PCI ed Slot PCI Express)Slot di espansione (Slot PCI ed Slot PCI Express)
Sulla scheda madre X58 Extreme3 c’è 2 slot PCI ed 4 slot PCI Express. Slot PCI: Sono utilizzati per installare schede di espansione con Interfa cci a PCI
a 32-bit.
Slot PCI Express: L’alloggio PCIE2 (PCIE x1; bianco) è usato per le
schede PCI Express x1 lane, come schede Gigabit LAN e SATA2. L’alloggio PCIE1 / PCIE3 (PCIE x16; blu) è usato per le schede grafiche PCI Express x16 lane, oppure è usato per installare schede grafiche PCI Express per supportare la funzione CrossFireXTM o SLITM. L’alloggio PCIE4 (PCIE x16; bianco) è usato per le schede PCI Express x1 lane, come schede Gigabit LAN, SATA2, eccetera.
1. In modalità scheda VGA singola, si raccomanda di installare una scheda video PCI Express x16 nell’alloggio PCIE1.
2. In modalità CrossFireXTM o SLITM, installare le schede video PCI Express x16 negli alloggi PCIE1 e PCIE3. Quindi, entrambi gli alloggi lavoreranno a larghezza di banda x16.
3. Collegare una ventola chassis al relativo connettore della scheda madre (CHA_FAN1 or CHA_FAN2) quando si usano più schede video per ottenere un migliore ambiente termico.
Installare una scheda di espansioneInstallare una scheda di espansione
Installare una scheda di espansione
Installare una scheda di espansioneInstallare una scheda di espansione
Step 1. Prima d’installare la scheda di espansione, assicurarsi che l’alimentazione
sia stata esclusa oppure che il cavo di alimentazione sia scollegato. Prima di iniziare l’installazione, si prega di leggere la documentazione della scheda di espansione e di effettuare le ne cessarie i mpostazioni del hardware.
Step 2. Rimuovere i ganci sullo slot che si intende utilizzare. Tenere a portata di mano
le viti.
Step 3. Allineare il connettore della scheda con lo slot e premere con decisione
finché la scheda è completamente in serita nello slot.
Step 4. Agganciare la scheda allo chassis con le viti.
100100
100
100100
ASRock X58 Extreme3 Motherboard
Loading...