Asrock B85M-DGS User Manual

B85M DGSB85M DGS

B85M-DGSB85M-DGS

Version 1.1

Published October 2014

Copyright©2014 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 5

1.4 I/O Panel 7

Chapter 2 Installation 8

2.1 Installing the CPU 9

2.2 Installing the CPU Fan and Heatsink 12

2.3 Installing Memory Modules (DIMM) 13

2.4 Expansion Slots (PCI Express Slots) 15

2.5 Jumpers Setup 16

2.6 Onboard Headers and Connectors 17

Chapter 3 Software and Utilities Operation 22

3.1 Installing Drivers 22

3.2 A-Tuning 23

3.3 Intel® Rapid Start Technology 29

3.4 Intel® Smart Connect Technology 34

3.5 ASRock APP Shop 39

3.5.1 UI Overview 39

3.5.2 Apps 40

3.5.3 BIOS & Drivers 43

3.5.4 Setting 44

3.6 Start8 45

Chapter 4 UEFI SETUP UTILITY 48

4.1 Introduction 48

4.1.1 UEFI Menu Bar 48

4.1.2 Navigation Keys 49

4.2 Main Screen 50

4.3 OC Tweaker Screen 51

4.4 Advanced Screen 59

4.4.1 CPU Conguration 60

4.4.2 Chipset Conguration 62

4.4.3 Storage Conguration 64

4.4.4 Intel® Rapid Start Technology 65

4.4.5 Intel® Smart Connect Technology 66

4.4.6 Super IO Conguration 67

4.4.7 ACPI Conguration 68

4.4.8 USB Conguration 70

4.4.9 Trusted Computing 72

4.5 Tools 73

4.6 Hardware Health Event Monitoring Screen 76

4.7 Boot Screen 77

4.8 Security Screen 80

4.9 Exit Screen 81

Chapter 1 Introduction

ank you for purchasing ASRock B85M-DGS motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality

and endurance.

In this manual, Chapter 1 and 2 contains the introduction of the motherboard

and step-by-step installation guides. Chapter 3 contains the operation guide of the

soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation w ill be subject to change w ithout notice. In case any
modications of this documentation occur, the updated ve rsion will be available on
ASRock’s website w ithout furthe r notice. If you require technical support relate d to
this motherboard, ple ase vi sit our website for specic information about the model
you are using. You may nd the l atest VGA cards and CPU support list on ASRock ’s
website a s well. ASRock website ht tp://www.asrock .com.

1.1 Package Contents

ASRock B85M-DGS Motherboard (Micro ATX Form Factor)

•

ASRock B85M-DGS Quick Installation Guide

•

ASRock B85M-DGS Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

•

B85M-DGS

English

1

English

1.2 Specications

Platform

CPU

Chipset

Memory

Expansion
Slot

Graphics

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Micro ATX Form Factor

All Solid Capacitor design

High Density Glass Fabric PCB

Supports New 4th and 4th Generation Intel® CoreTM i7/i5/i3/

Xeon®/Pentium®/Celeron® Processors (Socket 1150)

Supports Intel® Turbo Boost 2.0 Technology

Intel® B85

Dual Channel DDR3 Memory Technology

2 x DDR3 DIMM Slots

Supports DDR3 1600/1333/1066 non-ECC, un-buered

memory

Max. capacity of system memory: 16GB (see CAUTION)

Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2

1 x PCI Express 3.0 x16 Slot (PCIE1: x16 mode)

1 x PCI Express 2.0 x1 Slot

Intel® HD Graphics Built-in Visua ls and the VGA outputs can

be supported only with processors which are GPU integrated.

Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD

Technology, Intel® InsiderTM, Intel® HD Graphics 4400/4600

Pixel Shader 5.0, DirectX 11.1

Max. shared memory 1792MB

Dual graphics output: support DVI-D and D-Sub by

independent display controllers

Supports DVI-D with ma x. resolution up to 1920x1200 @

60Hz

Supports D-Sub with max. resolution up to 1920x1200 @

60Hz

Supports HDCP with DVI-D Port

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

Port

2

Audio

LAN

Rear Panel
I/O

5.1 CH HD Audio (Realtek ALC662 Audio Codec)

•

Supports Surge Protection (ASRock Full Spike Protection)

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111GR

•

Supports Wake-On-WAN

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection (ASRock Full Spike

•

Protection)

Supports LAN Cable Detection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

4 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))

2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

B85M-DGS

Storage

Connector

4 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug

1 x Print Port Header

•

1 x COM Port Header

•

1 x Chassis Intrusion Header

•

1 x TPM Header

•

1 x CPU Fan Connector (4-pin)

•

1 x Chassis Fan Connector (4-pin)

•

1 x Power Fan Connector (3-pin)

•

1 x 24 pin ATX Power Connector

•

1 x 4 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

English

3

BIOS
Feature

Hardware
Monitor

OS

Certica­tions

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD

•

Protection (ASRock Full Spike Protection))

1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports ESD

•

Protection (ASRock Full Spike Protection))

32Mb AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 1.1 Compliant wake up events

•

SMBIOS 2.3.1 support

•

CPU, DRAM, PCH 1.05V, PCH 1.5V Voltage multi-adjust-

•

ment

CPU/Chassis temperature sensing

•

CPU/Chassis/Power Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature)

CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

•

Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-

•

bit / 7 32-bit / 7 64-bit

FCC, CE, WHQL

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

English

4

* For detailed product information, please visit our website: http://ww w.asrock.com

Please realiz e that there is a certain r isk involved with overclocking , including adju st­ing the setting in the BIOS, applying Untied Overclocking Technology, or using third­party o verclocking tools. O verclo cking may aect your system’s stability, or even cause
damage to the components and dev ices of your system. It should be done at your own
risk and expense. We are not responsible for possible damage caused by overclocking.

Due to limitation, the actual memory size may be l ess than 4GB for the reser vation
for system usage under Windows® 32-bit operating systems. Windows® 64-bit operat­ing systems do not have such limitations. You can use ASRock XFast RA M to utilize
the memory that Windows® cannot use.

1.3 Motherboard Layout

Intel

B85

DDR 3_B1 (6 4 bit, 24 0-pin m odule )

DDR 3_A1 (6 4 bit, 24 0-pin m odule )

CMO S

Bat tery

Sup er

I/O

ATXP WR 1

LAN

Top:
RJ- 45

USB 2 .0
T: USB2
B: US B3

CLRCMO S1

1

1

SPEAKER1

HDLED RESET

PLED P WRBTN

PANEL1

1

USB4_5

1

COM1

1

1

HD_AU DIO1

B85M-DG S

CHA_FA N1

RoHS

7

8

14

16

12

13

17

19

20

21

18

15

2

CPU_FAN1

3

4

6

5

1

32Mb
BIOS

VGA1

Audio

CODEC

PCIE1

Fro nt USB 3. 0

PWR_FA N1

1

TPMS1

1

1

LPT1

CI1

1

USB3 _2_3

9

10

11

SATA3_3

PCIE2

USB 3. 0
T: USB0
B: US B1

Top:

LINE IN

Cente r:

FRONT

Botto m:

MIC IN

USB6_7

1

ATX12V 1

SATA3_1

SATA3_2

SATA3_0

PCI Express 3.0

USB 2. 0

T: USB0

B: USB 1

PS2

Keyb oard/

Mous e

DVI1

B85M-DGS

English

5

No. Description

1 CPU Fan Connector (CPU_FAN1)

2 ATX 12V Power Connector (ATX12V1)

3 Power Fan Connector (PWR_FAN1)

4 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1)

5 ATX Power Connector (ATXPWR1)

6 SATA3 Connector (SATA3_3)

7 SATA3 Connector (SATA3_2)

8 SATA3 Connector (SATA3_0)

9 SATA3 Connector (SATA3_1)

10 USB 3.0 Header (USB3_ 2_3)

11 Clear CMOS Jumper (CLRCMOS1)

12 System Panel Header (PANEL1)

13 TPM Header (TPMS1)

14 USB 2.0 Header (USB6_7)

15 Chassis Speaker Header (SPEAKER1)

16 USB 2.0 Header (USB4_5)

17 Chassis Fan Connector (CHA_FAN1)

18 Print Port Header (LPT1)

19 COM Port Header (COM1)

20 Chassis Intrusion Header (CI1)

21 Front Panel Audio Header (HD_AUDIO1)

English

6

1.4 I/O Panel

1

B85M-DGS

3

2 4

10

8

No. Description No. Description

1 USB 2.0 Ports (USB01) 6 USB 2.0 Ports (USB23)

2 LAN RJ-45 Port* 7 USB 3.0 Ports (USB3_01)

3 Line In (Light Blue) 8 D-Sub Port

4 Front Speaker (Lime) 9 DVI-D Port

5 Microphone (Pink) 10 PS/2 Mouse/Keyboard Port

* ere are two LEDs on each LA N port. Please refer to the table below for the LAN port LED indications.

ACT/LINK L ED

SPEED LE D

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

5679

English

7

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

8

2.1 Installing the CPU

1. Before you insert the 1150-Pin CPU into the socket, please check if the P nP cap is on
the socket, if the CPU surface is unclean , or if there are any bent pins in the sock et.
Do not force to insert the CPU into the socket if above situation is found. Otherwise ,
the CPU will be seriously damaged.

2. Unplug all power c ables before in stalling the CPU.

1

B85M-DGS

A

B

2

English

9

4

5

3

10

English

Please save and replace the cover if the proc essor is removed. e cover must be placed
if you wish to retur n the motherboard for aer service.

B85M-DGS

11

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

12

N

FA

_

U

P

C

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always ne ed to install id entical (the same

brand, speed , size and chip-type) DDR3 DI MM pairs.

2. It is unable to activate Dual Channel Memor y Technol ogy with only one memory
module installed.

3. It is not allowed to install a DDR or DDR2 me mory module into a DDR3 slot ;
otherwise , this motherboard and DIM M may be damaged.

e DIMM only ts in one correct orie ntation. It will cause permanent damage to
the mothe rboard and the DIMM if you force the DIMM into the slot at incorrect
orientation .

B85M-DGS

13

English

1

2

3

14

English

2.4 Expansion Slots (PCI Express Slots)

ere are 2 PCI Express slots on the motherboard.

Before installing an ex pansion card , please make s ure that the power s upply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you star t
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

PCIE2 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width graphics cards.

B85M-DGS

15

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRCMOS1)

(see p.5, No. 11)

CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear

the CMOS right aer you update the BIOS. If you need to clear the CMOS when

you just nish updating the BIOS, you must boot up the system rst, and then shut

it down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOSDefault

English

16

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option
“Clear Status” to clear the record of previous chassis intrusion status.

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. D o NOT place jumper caps over
these headers and connectors. Plac ing jumper caps over the headers and connectors
will cause permane nt damage to the motherboard.

B85M-DGS

System Panel Header

(9-pin PANEL1)

(see p.5, No. 12)

PWRBTN (Power Sw itch):

Connec t to the power switch on the ch assi s front panel. You may congure the way to
turn o your system using the powe r switch.

RESET (Reset Switch):

Connec t to the reset switch on the chassi s front panel. P ress the reset switch to re start
the computer if the compute r freezes and fails to perform a normal restart.

PLED (Syste m Power LED):

Connec t to the power status indicator on the chas sis front panel. e LED i s on when
the system is ope rating. e LED keeps blinking when the system is in S1/S3 sleep state .
e LED is o when the system i s in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):

Connec t to the hard drive ac tivity LED on the chassis front panel . e LED is on when
the hard dr ive is reading or w riting data.

e front panel de sign may dier by chassis. A f ront panel module mainly consists
of power switch , reset switch, power LED, hard dr ive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make s ure the wire
assig nments and the pin assig nments are matched correctly.

1

PLE D+

PLE D-

HDL ED-

HDL ED+

PWR BTN#

GND

RES ET#

GND

GND

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

17

English

Serial ATA3 Connectors

(SATA3_0:

see p.5, No. 8)

(SATA3_1:

see p.5, No. 9)

(SATA3_2:

see p.5, No. 7)

(SATA3_3:

see p.5, No. 6)

ese four SATA3

connectors support SATA

data cables for internal

SATA3_3

SATA3_2

storage devices with up to

6.0 Gb/s data transfer rate.

SATA3_1

SATA3_0

USB 2.0 Headers

(9-pin USB4_ 5)

(see p.5, No. 16)

(9-pin USB6_7)

(see p.5, No. 14)

USB 3.0 Header

(19-pin USB3_2_3)

(see p.5, No. 10)

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.5, No. 21)

USB _PW R

1

USB _PW R

Vbus

IntA _PA_SS RX-

IntA _PA_SS RX+

GND

IntA _PA_SS TX-

IntA _PA_SS TX+

GND

IntA _PA_D-

IntA _PA_D+

GND

1

MIC 2_L

P-

P+

GND

GND

P+

P-

1

PRE SENCE #

MIC _RET

J_S ENSE

OUT 2_R

MIC 2_R

DUM MY

VbusVbus

IntA _PB_S SRX-

IntA _PB_S SRX+

GND

IntA _PB_S STX-

IntA _PB_S STX+

GND

IntA _PB_D -

IntA _PB_D +

Dumm y

OUT _RET

OUT 2_L

Besides four USB 2.0 ports

on the I/O panel, there

are two headers on this

motherboard. Each USB

2.0 header can support

two ports.

Besides two USB 3.0 ports

on the I/O panel, there

is one header on this

motherboard. Each USB

3.0 header can support

two ports.

is header is for

connecting audio devices

to the front audio panel.

English

18

1. High Denition Audio supports Jack Sen sing, but the panel wire on the chassis mu st

GND

+12 V

FAN_ SPEED

FAN_S PEED

FAN_S PEED_ CONTR OL

GND

+12V

1 2 3 4

FAN_S PEED

FAN_S PEED_ CONTR OL

+12V

GND

4

3

2

1

suppor t HDA to function correctly. Please follow the instr uctions in our manual and
chassis manual to install your system.

2. If you use an AC’97 audio panel , please install it to the front panel audio head er by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connec t them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Cont rol panel
and adju st “Recording Volume”.

Chassis Speaker Header

(4-pin SPEAKER1)

(see p.5, No. 15)

DUM MY

1

+5V

SPE AKER

DUM MY

B85M-DGS

Please connect the chassis

speaker to this header.

Chassis and Power Fan

Connectors

(4-pin CHA_FAN1)

(see p.5, No. 17)

(3-pin PWR_FAN1)

(see p.5, No. 3)

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.5, No. 1)

ATX Power Connector

(24-pin ATXPWR1)

(see p.5, No. 5)

Please connect fan cables

to the fan connectors and

match the black wire to

the ground pin.

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

24

12

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

English

plug it along Pin 1 and Pin

1

13

13.

19

ATX 12V Power

Connector

(4-pin ATX12V1)

(see p.5, No. 2)

Please connect an ATX

12V power supply to this

connector.

Serial Port Header

(9-pin COM1)

(see p.5, No. 19)

Chassis Intrusion Header

(2-pin CI1)

(see p.5, No. 20)

TPM Header

(17-pin TPMS1)

(see p.5, No. 13)

is COM1 header

supports a serial port

module.

is motherboard

supports CASE OPEN

detection feature that

1

RRXD 1

DDTR #1

TTXD 1

DDCD #1

1

Sig nal

DDSR #1

CCTS #1

RRTS #1

GND

GND

RRI# 1

detects if the chassis cove

has been removed. is

feature requires a chassis

with chassis intrusion

detection design.

is connector supports

Trusted Platform Module

(TPM) system, which can

SMB _CLK_ MAIN

GND

SMB _DATA _MAIN

LAD 2

GND

LAD 1

S_P WRDWN #

SER IRQ#

GND

securely store keys, digital

1

+3V

LAD 3

LAD 0

FRA ME

PCI CLK

PCI RST#

certicates, passwords,

and data. A TPM system

GND

+3V SB

also helps enhance

network security, protects

digital identities, and

ensures platform integrity.

English

20

B85M-DGS

Print Port Header

(25-pin LPT1)

(see p.5, No. 18)

1

AFD #

STB #

ERR OR#

PIN IT#

SPD 1

SPD 0

SLI N#

SPD 2

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

is is an interface

for print port cable

that allows convenient

connection of printer

PE

SLC T

devices.

21

English

Chapter 3 Software and Utilities Operation

3.1 Installing Drivers

e Support CD that comes with the motherboard contains necessary drivers and

useful utilities that enhance the motherboard’s features.

Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. e CD

automatically displays the Main Menu if “AUTORUN” is enabled in your computer.

If the Main Menu does not appear automatically, locate and double click on the le

“ASRSETUP.EXE” in the Support CD to display the menu.

Drivers Menu

e drivers compatible to your system will be auto-detected and listed on the

support CD driver page. Please click Install All or follow the order from top to

bottom to install those required drivers. erefore, the drivers you install can work

properly.

Utilities Menu

e Utilities Menu shows the application soware that the motherboard supports.

Click on a specic item then follow the installation wizard to install it.

To improve Windows 7 compatibility, please download and install the following hot
x provided by Microso.
“KB2720599”: http://support.microso.com/kb/2720599/en-us

English

22