ASRock B460 phantom Gaming 4 operation manual

Version 1.1

Published May 2020

Copyright©2020 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel

: [phone] ext.123 (Standard International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 7

1.4 I/O Panel 9

Chapter 2 Installation 10

2.1 Installing the CPU 11

2.2 Installing the CPU Fan and Heatsink 14

2.3 Installing Memory Modules (DIMM) 15

2.4 Expansion Slots (PCI Express Slots) 17

2.5 Jumpers Setup 18

2.6 Onboard Headers and Connectors 19

2.7 Post Status Checker 25

2.8 CrossFireXTM and Quad CrossFireXTM Operation Guide 26

2.8.1 Installing Two CrossFireXTM-Ready Graphics Cards 26

2.8.2 Driver Installation and Setup 28

2.9 M.2 WiFi/BT Module Installation Guide 29

2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 31

Chapter 3 Software and Utilities Operation 35

3.1 Installing Drivers 35

3.2 ASRock Motherboard Utility (Phantom Gaming Tuning) 36

3.3 ASRock Live Update & APP Shop 39

3.3.1 UI Overview 39

3.3.2 Apps 40

3.3.3 BIOS & Drivers 43

3.3.4 Setting 44

3.4 Nahimic Audio 45

3.5 ASRock Polychrome SYNC 46

Chapter 4 UEFI SETUP UTILITY 49

4.1 Introduction 49

4.2 EZ Mode 50

4.3 Advanced Mode 51

4.3.1 UEFI Menu Bar 51

4.3.2 Navigation Keys 52

4.4 Main Screen 53

4.5 OC Tweaker Screen 54

4.6 Advanced Screen 64

4.6.1 CPU Conguration 65

4.6.2 Chipset Conguration 67

4.6.3 Storage Conguration 70

4.6.4 Intel(R) Thunderbolt 71

4.6.5 Super IO Conguration 72

4.6.6 ACPI Conguration 73

4.6.7 USB Conguration 75

4.6.8 Trusted Computing 76

4.7 Tools 77

4.8 Hardware Health Event Monitoring Screen 79

4.9 Security Screen 83

4.10 Boot Screen 84

4.11 Exit Screen 87

B460 Phantom Gaming 4

Chapter 1 Introduction

ank you for purchasing ASRock B460 Phantom Gaming 4 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation

guide of the soware and utilities. Chapter 4 contains the conguration guide of

the BIOS setup.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website w ithout f urther notice. If you require technical support relate d to
this motherboard, please vi sit our website for s pecic information about the model
you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s
website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock B460 Phantom Gaming 4 Motherboard (ATX Form Factor)

•

ASRock B460 Phantom Gaming 4 Quick Installation Guide

•

ASRock B460 Phantom Gaming 4 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

2 x Screws for M.2 Sockets (Option al)

•

1 x I/O Panel Shield

•

English

1

1.2 Specications

Platform

CPU

Chipset

Memory

* Please refer to Memory Support List on ASRock's website for

more information. (http://www.asrock.com/)

* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),

Pentium® and Celeron® support DDR4 up to 2666.

ATX Form Factor

•

Solid Capacitor design

•

Suppor ts 10th Gen Intel® CoreTM Processors (Socket 1200)

•

Digi Power design

•

9 Power Phase design

•

Supports Intel® Turbo Boost Max 3.0 Technology

•

Intel® B460

•

Dual Channel DDR4 Memory Technology

•

4 x DDR4 DIMM Slots

•

Supports DDR4 2933/2800/2666/2400/2133 non-ECC, un-

•

buered memory

Supports ECC UDIMM memory modules (operate in non-

•

ECC mode)

Max. capacity of system memory: 128GB

•

Supports Intel® Extreme Memory Prole (XMP) 2.0

•

15μ Gold Contact in DIMM Slots

•

English

2

Expansion
Slot

2 x PCI Express 3.0 x16 Slots (PCIE1/PCIE3: single at x16

•

(PCIE1); dual at x16 (PCIE1) / x4 (PCIE3)*

* Supports NVMe SSD as boot disks

2 x PCI Express 3.0 x1 Slots

•

Supports AMD Quad CrossFireXTM and CrossFireXTM

•

1 x M.2 Socket (Key E), supports ty pe 2230 WiFi/BT module

•

B460 Phantom Gaming 4

Graphics

Audio

* Intel® UHD Graphics Built-in Visuals and the VGA outputs can

be supported only with processors which are GPU integrated.

Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265

•

8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,

MJ PEG, VC-1

* VP9 10bit and VC-1 are for decode only.

* VP8 and VP9 encode are not supported by Windows OS.

Graphics, Media & Compute: Microso DirectX 12, OpenGL

•

4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /

Switchable Graphics, OpenCL 2.1

Display & Content Security: Rec. 2020 (Wide Color Gamut),

•

Microso PlayReady 3.0, Intel® SGX Content Protection,

UHD/HDR Blu-ray Disc

Supports HDMI 1.4 with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI 1.4 Port

(Compliant HDMI monitor is required)

Supports HDCP 2.3 with HDMI 1.4 Port

•

Supports 4K Ultra HD (UHD) playback with HDMI 1.4 Port

•

7.1 CH HD Audio with Content Protection (Realtek ALC1200

•

Audio Codec)

Premium Blu-ray Audio support

•

Supports Surge Protection

•

PCB Isolate Shielding

•

Individual PCB Layers for R/L Audio Channel

•

Nahimic Audio

•

LAN

Gigabit LAN 10/100/10 00 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

English

3

English

Rear Panel
I/O

Storage

Connector

1 x Antenna Bracket

•

1 x PS/2 Mouse/Keyboard Port

•

1 x HDMI Port

•

4 x USB 3.2 Gen1 Type-A Ports (Supports ESD Protection)

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

•

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology

17), NCQ, AHCI and Hot Plug*

* If M2_2 is occupied by a SATA-type M.2 device, SATA3_0 will

be disabled.

1 x Ultra M.2 Socket (M2_2), supports M Key type

•

2280/22110 M.2 SATA3 6.0 Gb/s module and M.2 PCI

Express module up to Gen3 x4 (32 Gb/s)**

** Supports NVMe SSD as boot disks

** Supports ASRock U.2 Kit

1 x COM Port Header

•

1 x SPI TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

2 x RGB LED Headers

•

* Support in total up to 12V/3A, 36W LED Strip

2 x Addressable LED Headers

•

* Support in total up to 5V/3A, 15W LED Strip

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of ma ximum

1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control)

* e CPU/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

5 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control)

* e Chassis/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

4

BIOS
Feature

Hardware
Monitor

B460 Phantom Gaming 4

* CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP, CHA_

FAN3/WP, CHA_FAN4/WP and CHA_FAN5/WP can auto

detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

1 x underbolt AIC Connector (5-pin) (Supports ASRock

•

underbolt 3 AIC R2.0 Card only)

2 x USB 2.0 Headers (Supports 3 USB 2.0 ports) (Supports

•

ESD Protection)

2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)

•

(Supports ESD Protection)

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU Core/Cache, GT, DRAM, PCH, VCCIO, VCCST,

•

VCCSA Voltage Multi-adjustment

Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-

•

ter Pump Fans

Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

•

Pump Fans

Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans

Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

•

Water Pump Fans

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

VPPM, PCH, VCCST

OS

Certica­tions

Microso® Windows® 10 64-bit

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

English

5

* For detailed product information, please visit our website: http://www.asrock .com

Please realize that the re is a certain r isk involved with overclo cking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technol ogy, or using
third-party overclocking tool s. Overclocking may aect your system’s stability, or
even cause dam age to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for poss ible damage caused by
overclocking.

English

6

1.3 Motherboard Layout

Intel

B460

DDR 4_A2 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

DDR 4_B2 (6 4 bit, 28 8-pin m odule )

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

ATX12V1

USB 2. 0

T: USB1

B: USB 2

ATXP WR 1

PCIE1

Top:
RJ-45

USB 3.2 Gen1
T: USB3_1
B: USB3_2

PCIE3

HDLED RESET

PLED PWRBTN

PANEL1

1

USB3_4

1

1

SPK_CI1

COM1

1

1

HD_AUDIO1

RoHS

12

15

18

19

1

Ultra M.2

PCIe Gen3 x4

PS2

Keybo ard

/Mous e

CMOS

Battery

PCIE2

32

14

8

USB3_ 7_8

1

30

9

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

SATA3_1

SATA3_0

SATA3_2

SATA3_3

SATA3_4

SATA3_5

CLRMOS1

1

M2_ 3

M2_ 2

T B1

1

PCIE4

AUDIO
CODEC

USB3_5_6

1

13

20

24

25

26

29

21

3

2

CHA_FAN 5/WP

CHA_FAN1/WP

CHA_FAN3/WP

CPU_FAN2/WP

CPU_FAN1

4

5

10

CHA_FAN 4/WP

16

1

SPI_TPM_J1

17

28

ADDR_LED1

1

RGB_LED1

1

27

31

ADDR_LED2

1

RGB_LED2

1

6

7

33

SUPER

I/O

HDMI 1

23

CHA_FAN2/WP

CPU

DRAM

VGA

BOOT

22

USB_5

1

11

USB 3.2 Gen1
T: USB3_4
B: USB3_3

B460 Phantom Gaming 4

English

7

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

5 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

6 RGB LED Header (RGB_LED2)

7 Addressable LED Header (ADDR_LED2)

8 ATX Power Connector (ATXPWR1)

9 USB 3.2 Gen1 Header (USB3_7_8)

10 Chassis/Water Pump Fan Connector (CHA_FAN5/WP)

11 USB 2.0 Header (USB_5)

12 SATA3 Connector (SATA3_3)

13 SATA3 Connector (SATA3_2)

14 SATA3 Connector (SATA3_5)

15 SATA3 Connec tor (SATA3_4)

16 Chassis/Water Pump Fan Connector (CHA _FAN4/WP)

17 SPI TPM Header (SPI_TPM_J1)

18 Chassis Intrusion and Speaker Header (SPK_CI1)

19 SATA3 Connector (SATA3_0)

20 SATA3 Connector (SATA3_1)

21 System Panel Header (PANEL1)

22 Post Status Checker (PSC)

23 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

24 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)

25 USB 3.2 Gen1 Header (USB3_5_6)

26 USB 2.0 Header (USB3_4)

27 Addressable LED Header (ADDR_LED1)

28 COM Port Header (COM1)

29 Front Panel Audio Header (HD_AUDIO1)

30 RGB LED Header (RGB_LED1)

31 Clear CMOS Jumper (CLRMOS1)

32 underbolt AIC Connector (TB1)

33 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

8

1.4 I/O Panel

B460 Phantom Gaming 4

1

10

9

2

7

68

No. Description No. Description

1 USB 2.0 Ports (USB1_2) 6 USB 3.2 Gen1 Ports (USB3_3_4)

2 LAN RJ-45 Port* 7 USB 3.2 Gen1 Ports (USB3_1_2)

3 Line In (Light Blue)** 8 HDMI Port

4 Front Speaker (Lime)** 9 PS/2 Mouse/Keyboard Port

5 Microphone (Pink)** 10 Antenna Bracket

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications .

ACT/LINK LED

SPEED LED

3

4

5

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

English

9

Chapter 2 Installation

is is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

10

2.1 Installing the CPU

1. Before you insert the 1200-Pin CPU into the socke t, please check if the PnP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not
force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.

2. Unplug all power cables before installing the CPU.

1

B460 Phantom Gaming 4

A

B

2

English

11

3

5

4

English

12

B460 Phantom Gaming 4

Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.

13

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

14

CPU_FAN

B460 Phantom Gaming 4

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,

and supports Dual Channel Memory Technology.

1. For dual channel conguration, you a lways need to install identical (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Me mory Technology w ith only one or three

memory module installed.

3. It is not allowed to ins tall a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated
2 Populated Populated Populated Populated

e DIMM only ts in one correct orientation. It will cause permanent dam age to
the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect
orientation.

15

English

1

2

English

16

3

B460 Phantom Gaming 4

2.4 Expansion Slots (PCI Express Slots)

ere are 4 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you start
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.

PCIE4 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

PCIe Slot Congurations

PCIE1 PCIE3

Single Graphics Card x16 N/A

Two Graphics Cards in

CrossFireXTM Mode

For a better ther mal environment, ple ase connect a ch assi s fan to the motherboard’s
chassis fan connector (CHA_ FAN1/WP, CHA_ FAN2/WP, CHA_FAN3/WP, CHA_
FAN4/WP or CHA_ FAN5/WP) when u sing multiple graphics cards.

x16 x4

English

17

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“O pen”.

Clear CMOS Jumper

(CLRMO S1)

(see p.7, No. 31)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short the pins on CLR MOS1 for 5 seconds. However, please do not clear the

CMOS right aer you update the BIOS. If you need to clear the CMOS when you

just nish updating the BIOS, you must boot up the system rst, and then shut it

down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

English

18

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these header s and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

B460 Phantom Gaming 4

System Panel Header

(9-pi n PANEL1)

(see p.7, No. 21)

PWRBTN (Power Button):

Connec t to the power button on the chassi s front panel. You may congure the way to
turn o your system using the power button.

RESET (Reset Button):
Connec t to the reset button on the chassi s front panel. Press the reset button to
restar t the computer if the computer freezes and fails to perform a nor mal restart.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when
the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep
state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on
when the hard drive i s reading or writing data.

e front panel de sign may dier by chassis. A front pane l module mainly consists
of power button , reset button, power LED, hard dr ive activity LED, speaker and etc.
When connecting your chassis front panel module to this head er, make sure the wire
assig nments and the pin assig nments are matched correctly.

1

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

GND

Connect the power button,

reset button and system

status indicator on the

chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting the

cables.

19

English

Chassis Intrusion and

USB_PWR

SPEAKER

Speaker Header

(7-pi n SPK _CI1)

(see p.7, No. 18)

DUMMY
+5V

1

SIGNAL

DUMMY

GND

DUMMY

Please connect the

chassis intrusion and the

chassis speaker to this

header.

Serial ATA3 Connectors

(SATA3_0:

see p.7, No. 19)

(SATA3_1:

see p.7, No. 20)

(SATA3_ 2:

see p.7, No. 13)

(SATA3_ 3:

see p.7, No. 12)

(SATA3_4:

see p.7, No. 15)

(SATA3_ 5:

see p.7, No. 14)

USB 2.0 Headers

(9-pin USB3_4)

(see p.7, No. 26)

(4-pin USB_5)

(see p.7, No. 11)

SATA3_2

SATA3_4

SATA3_1

USB_PWR

1

USB_PWR

GND

P-

P+

P+

P-

P+

SATA3_0

GND

DUMMY

GND

P-

1

ese six SATA3

connectors support SATA

data cables for internal

storage devices with up to

SATA3_3

6.0 Gb/s data transfer rate.

* If M2_2 is occupied by

a SATA-type M.2 device,

SATA3_5

SATA3_0 will be disabled.

ere are two USB

2.0 headers on this

motherboard.

English

20

USB 3.2 Gen1 Headers

(19-pin USB3_5_6)

(see p.7, No. 25)

1

IntA_PA_D+

IntA_PA_D-

Dummy

IntA_PB_D+

IntA_PA_SSTX+

GND

GND

IntA_PB_D-

IntA_PA_SSRX+

IntA_PA_SSRX-

IntA_PA_SSTX-

GND

IntA_PB_SSTX+

IntA_PB_SSTX-

GND

IntA_PB_SSRX+

ere are two headers on

this motherboard. Each

Vbus

USB 3.2 Gen1 header can

support two ports.

IntA_PB_SSRX-

VbusVbus

B460 Phantom Gaming 4

(19-pin USB3_7_8)

(see p.7, No. 9)

Front Panel Audio Header

(9-pin HD_ AUDIO1)

(see p.7, No. 29)

1. High Denition Audio support s Jack Sensing , but the panel wire on the cha ssis

must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front pane l audio header by

the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connec t them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

GND

1

MIC2_L

1

PRESENCE#

MIC_RET

J_SENSE

OUT2_R

MIC2_R

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

OUT_RET

OUT2_L

is header is for

connecting audio devices

to the front audio panel.

21

English

Chassis/Water Pump Fan

4 3 2 1

4

Connectors

(4-pin CHA_FAN1/WP)

(see p.7, No. 33)

(4-pin CHA_FAN2/WP)

(see p.7, No. 23)

(4-pin CHA_FAN3/WP)

(see p.7, No. 24)

(4-pin CHA_FAN4/WP)

(see p.7, No. 16)

(4-pin CHA_FAN5/WP)

(see p.7, No. 10)

GND

FAN_VOLTAGE

CHA_FAN_SPEED

FAN_SPEED_CONTROL

1 2 3 4

FAN_SPEED_CONTROL

CHA_FAN_SPEED

FAN_VOLTAGE

GND

1

FAN_VOLTAGE

2

CHA_FAN_SPEED

3

4

FAN_SPEED_CONTROL

is motherboard provides

ve 4-Pin water cooling

chassis fan connectors. If

you plan to connect a 3-Pin

chassis water cooler fan,

please connect it to Pin 1-3.

GND

English

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.7, No. 2)

CPU/Water Pump Fan

Connector

(4-pin CPU_FAN2/WP)

(see p.7, No. 5)

ATX Power Connector

(24-p i n ATX PWR1)

(see p.7, No. 8)

FAN_SPEED_CONTROL

CPU_FAN_SPEED

FAN_VOLTAGE

GND

FAN_VOLTAGE

CPU_FAN_SPEED

GND

FAN_SPEED_CONTROL

1 2 3 4

12

1

is motherboard provides

3

a 4-Pin CPU fan (Quiet

2
1

Fan) connector. If you plan

to connect a 3-Pin CPU

fan, please connect it to Pin

1-3.

is motherboard provides

a 4-Pin water cooling CPU

fan connector. If you plan

to connect a 3-Pin CPU

water cooler fan, please

connect it to Pin 1-3.

24

is motherboard provides

a 24-pin ATX power con-

nector. To use a 20-pin

ATX power supply, please

13

plug it along Pin 1 and Pin

13.

22

B460 Phantom Gaming 4

SPI_DQ3

8 5

ATX 12V Power

Connector

(8-pin ATX12V1)

(see p.7, No. 1)

Serial Port Header

(9-p in CO M1)

(see p.7, No. 28)

SPI TPM Header

(13 -pi n SPI_T PM _J1)

(see p.7, No. 17)

underbolt AIC

Connector

(5-pin TB1)

(see p.7, No. 32)

4

RRXD1

1

DDCD#1

+3.3V

TPM_Present

1

SPI_MISO

SPI_CS0

SPI_DQ2

1

DDTR#1

DDSR#1

GND

TTXD1

CLK

SPI_MOSI

GND

RSMRST#

1

CCTS#1

RRI#1

RRTS#1

RST#

TPM_PIRQ

SPI_TPM_CS#

is motherboard provides

an 8-pin ATX 12V power

connector. To use a 4-pin

ATX power supply, please

plug it along Pin 1 and Pin

5.

is COM1 header

supports a serial port

module.

is connector supports SPI

Trusted Platform Module (TPM)

system, which can securely

store keys, digital certicates,

passwords, and data. A TPM

system also helps enhance

network securit y, protects digital

identities, and ensures platform

integrity.

Please connect a

underbolt™ add-in card

(AIC) to this connector

via the GPIO cable.

*Please install the underbolt™

AIC card to PCIE3 (default slot).

RGB LED Headers

(4-p i n RGB_ LED1)

(see p.7, No. 30)

(4-pi n RGB _LED2)

(see p.7, No. 6)

1

12V GR B

B

R

G

12V

1

RGB headers are used to connect

RGB LED extension cables which

allow users to choose from

various LED lighting eects.

Caution: Never install the

RGB LED cable in the wrong

orientation; otherwise, the cable

may be damaged.

*Please refer to page 46 for further

instructions on this header.

English

23