Asrock B150M Pro4/Hyper Quick Installation Guide

Version 1.0
Published May 2016
Copyright©2016 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: [phone] ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

English

Motherboard Layout

Intel

B150

Sup er

I/O

ATXP WR1

HDLED RESET

PLED PWRBTN

PANEL1

1

COM1

1

B150M Pro4/Hyper

RoHS

2

3

6

1

Audio

CODEC

PCIE1

PCI Express 3.0

TPMS1

1

1

USB1_2

USB 3. 0

T: USB1

B: USB 2

PS2

Keyb oard

/Mous e

SPK_CI1

1

PCIE2

Front USB 3.0

16

171820212223

CMOS

Battery

DDR 4_A2 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

DDR 4_B2 (6 4 bit, 28 8-pin m odule )

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

5

4

ATX12V1

12

9

SATA3_2

SATA3_3

USB3_5 _6

13

14

15

SATA3_4

SATA3_5

BIOS
ROM

CHA_FAN2

10
11

CLRMOS1

1

1

HD_AUDIO1

PCIE3

Top:
RJ-45

USB 3.0
T: USB3
B: USB4

HDM I1

Top:

SIDE S PK

Cent er:

REAR S PK

Bott om:

CTR BA SS

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

CHA_FAN1

24

8

SATA3_1

7

SATA3_0

VGA 1

DVI1

CT4

M2_1

CT2

CT3

CT1

PCI1

Ultra M.2

PCIe Gen3 x4

CPU_FAN2CPU_FAN1

USB3_4

19

B150M Pro4/Hyper

1

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 CPU Fan Connector (CPU_FAN2)

4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

6 ATX Power Connector (ATXPWR1)

7 SATA3 Connector (SATA3_0)

8 SATA3 Connector (SATA3_1)

9 USB 3.0 Header (USB3_5_6)

10 Chassis Fan Connector (CHA_FAN2)

11 SATA3 Connector (SATA3_2)

12 SATA3 Connector (SATA3_3)

13 SATA3 Connector (SATA3_5)

14 SATA3 Connector (SATA3_4)

15 Clear CMOS Jumper (CLRMOS1)

16 System Panel Header (PANEL1)

17 Chassis Intrusion and Speaker Header (SPK_CI1)

18 USB 2.0 Header (USB1_2)

19 USB 2.0 Header (USB3_4)

20 TPM Header (TPMS1)

21 Print Port Header (LPT1)

22 COM Port Header (COM1)

23 Front Panel Audio Header (HD_AUDIO1)

24 Chassis Fan Connector (CHA_FAN1)

2

English

I/O Panel

B150M Pro4/Hyper

1

13 1011 9 812

No. Description No. Description

1 PS/2 Mouse/Keyboard Port 8 Microphone (Pink)

2 D-Sub Port 9 Central / Bass (Orange)

3 LAN RJ-45 Port* 10 USB 3.0 Ports (USB3_34)

4 Side Speaker (Gray) 11 HDMI Port

5 Rear Speaker (Black) 12 DVI-D Port

6 Line In (Light Blue) 13 USB 3.0 Ports (USB3_12)

7 Front Speaker (Lime)**

2

3 5

4

6

7

3

English

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below
for connection d etails in accordance w ith the type of speaker you use.

4

Audio Output

Channels

Front Speaker

(No. 7)

Rear Speaker

(No. 5)

Central / Bass

(No. 9)

2 V -- -- --
4 V V -- --
6 V V V --
8 V V V V

To enable Multi-Stre aming, you need to connect a front panel audio cable to the front
panel audio header. Aer restarting your computer, you will nd the “Mixer” tool
on your system. Please select “Mixer ToolBox” , click “Enable playback multi­streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are
allowed to select “Realtek HDA Pr imary output” to use the Rear Speaker, Central/
Bass, and Front Speake r, or select “Realtek HDA Audio 2nd output” to use the front
panel audio.

Line In
(No. 6)

English

B150M Pro4/Hyper

Chapter 1 Introduction

ank you for purchasing ASRock B150M Pro4/Hyper motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be available on ASRock’s
website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You
may nd the l atest VGA cards and CPU support list on ASRock’s website a s well. ASRock
website http://www.asrock.com.

1.1 Package Contents

ASRock B150M Pro4/Hyper Motherboard (Micro ATX Form Factor)

•

ASRock B150M Pro4/Hyper Quick Installation Guide

•

ASRock B150M Pro4/Hyper Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x I/O Panel Shield

•

1 x Screw for M.2 Socket

•

5

English

1.2 Specications

Platform

CPU

Chipset

Memory

* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)

Micro ATX Form Factor

•

Solid Capacitor design

•

th

Supports 6

•

Celeron® Processors (Socket 1151)
Digi Power design

•

6 Power Phase design

•

Supports Intel® Turbo Boost 2.0 Technology

•

Supports ASRock Hyper BCLK Engine

•

Intel® B150

•

Supports Intel® Small Business Advantage 4.0

•

Dual Channel DDR4 Memory Technology

•

4 x DDR4 DIMM Slots

•

Supports DDR4 2133 non-ECC, un-buered memory

•

Supports ECC UDIMM memory modules (operate in non-

•

ECC mode)

Max. capacity of system memory: 64GB

•

Supports Intel® Extreme Memory Prole (XMP) 2.0

•

15μ Gold Contact in DIMM Slots

•

Generation Intel® CoreTM i7/i5/i3/Pentium®/

6

Expansion
Slot

Graphics

2 x PCI Express 3.0 x16 Slots (PCIE1: x16 mode; PCIE3: x4

•

mode)*

* Supports NVMe SSD as boot disks

1 x PCI Express 3.0 x1 Slot (Flexible PCIe)

•

1 x PCI Slot

•

* If PCI or PCIE2 slot is occupied, M2_1 slot will support M.2
PCI Express module up to Gen3 x2 (16 Gb/s).

Supports AMD Quad CrossFireXTM and CrossFireXTM

•

Intel® HD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU
integrated.

English

B150M Pro4/Hyper

Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

•

Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTru
Technology, Intel® InsiderTM, Intel® HD Graphics 510/530
Pixel Shader 5.0, DirectX 12

•

Max. shared memory 1024MB

•

* e size of maximum shared memory may vary from dierent
operating systems.

ree graphics output options: D-Sub, DVI-D and HDMI

•

Supports Triple Monitor

•

Supports HDMI with max. resolution up to 4K x 2K

•

(4096x2160) @ 24Hz / (3840x2160) @ 30Hz
Supports DVI-D with max. resolution up to 1920x1200 @

•

60Hz
Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
Supports Accelerated Media Codecs: HEVC, VP8, VP9

•

Supports HDCP with DVI-D and HDMI Ports

•

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

•

and HDMI Ports

TM

3D, Intel® Clear Video HD

Audio

LAN

7.1 CH HD Audio with Content Protection (Realtek ALC892

•

Audio Codec)
Premium Blu-ray Audio support

•

Supports Surge Protection (ASRock Full Spike Protection)

•

ELNA Audio Caps

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection (ASRock Full Spike

•

Protection)
Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

7

English

Rear Panel
I/O

Storage

Connector

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

4 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LE D)
HD Audio Jacks: Side Speaker / Rear Speaker / Central / Bass

•

/ Line in / Front Speaker / Microphone

6 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug*
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_0 will
be disabled.

1 x Ultra M.2 Socket, supports type 2230/2242/2260/2280

•

M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module

up to Gen3 x4 (32 Gb/s)**
** If PCI or PCIE2 slot is occupied, M2_1 slot will support M.2
PCI Express module up to Gen3 x2 (16 Gb/s).
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit

1 x Print Port Header

•

1 x COM Port Header

•

1 x TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

2 x CPU Fan Connectors (1 x 3-pin, 1 x 4-pin) (Smart Fan

•

Speed Control)

2 x Chassis Fan Connectors (4-pin) (Smart Fan Speed

•

Control)
* CHA_FAN1 and CHA_FAN2 can auto detect if 3-pin or 4-pin
fan is in use.
* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

8

English

BIOS
Feature

Hardware
Monitor

B150M Pro4/Hyper

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports

•

ESD Protection (ASRock Full Spike Protection))
1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports

•

ESD Protection (ASRock Full Spike Protection))

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 5.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

DRAM, PCH 1.0V, VCCIO, VCCSA Voltage Multi-adjust-

•

ment

CPU/Chassis temperature sensing

•

CPU/Chassis Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature)
CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, GT_CPU,

•

DRAM, VPPM, PCH 1.0V, VCCIO, VCCSA

Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-

OS

Certica­tions

* For detailed product information, please visit our website: http://www.asrock.com

•

bit
* To install Windows® 7 OS, a modied installation disk with
xHCI drivers packed into the ISO le is required. Please refer to
page 150.
or more detailed instructions.
* For the updated Windows® 10 driver, please visit ASRock ’s
website for details: http://www.asrock.com

FCC, CE, WHQL

•

ErP/EuP Ready (ErP/EuP ready power supply is required)

•

9

English

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

10

English

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap i s on the
socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not
force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.

2. Unplug all power cables before in stalling the CPU.

1

B150M Pro4/Hyper

A

B

2

11

English

3

4

12

5

English

B150M Pro4/Hyper

Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.

13

English

2.2 Installing the CPU Fan and Heatsink

1 2

14

FAN

CPU_

English

B150M Pro4/Hyper

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.

1. For dual channel conguration , you always need to in stall identical (the same brand,
speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memor y Technology with only one or three memor y
module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 sl ot;
otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated
2 Populated Populated
3 Populated Populated Populated Populated

e DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

15

English

1

2

16

3

English

B150M Pro4/Hyper

2.4 Expansion Slots (PCI and PCI Express Slots)

ere are 1 PCI slot and 3 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and make necessary hardware settings for the card before you start
the installation.

PCI slot:

e PCI1 slot is used to install expansion cards that have 32-bit PCI interface.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
*If PCI or PCIE2 slot is occupied, M2_1 slot will support M.2 PCI Express module
up to Gen3 x2 (16 Gb/s).

PCIe Slot Congurations

PCIE1 PCIE3

Single Graphics Card x16 N/A

Two Graphics Cards in

CrossFireX

TM

Mode

For a better ther mal environment, please connect a chassi s fan to the motherboard’s
chassis fan connector (CHA_ FAN1 or CHA_FAN2) when using multiple graphic s
cards.

x16 x4

17

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper
(C LR MOS 1)
(see p.1, No. 15)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the
CMOS right aer you update the BIOS. If you need to clear the CMOS when you
just nish updating the BIOS, you must boot up the system rst, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.

Default

Clear CMOS

18

If you clear the CMOS, the case open may be detec ted. Please adjust the BIOS option “Clear
Status” to clear the record of previous chassis intrusion status.

English

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
heade rs and connectors. Placing jumper caps over the headers and connectors will cause
permanent damage to the motherboard.

B150M Pro4/Hyper

System Panel Header
(9-pi n PANEL1)
(see p.1, No. 16)

PWRBTN (Power Switch):

Connec t to the power switch on the chassi s front panel. You may congure the way to tur n
o your system using the power switch.

RESET (Reset Switch):
Connec t to the reset switch on the chassis front panel. Press the reset sw itch to restart the
computer if the computer f reezes and fails to perform a normal restar t.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chassis front panel. e LED i s on when the
system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e
LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the
hard drive is reading or wr iting data.

e front panel design may dier by chassis. A front panel module mainly consists of power
switch, reset switch , power LED, hard dr ive activity LED, speaker and etc. When connect­ing your chassi s front panel module to thi s header, make sure the wire a ssignments and the
pin assignments are matched correctly.

1

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

GND

Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.

19

English

Chassis Intrusion and

1

+5V

DUMMY

SIGNAL

GND

DUMMY

SPEAKER

DUMMY

DUMMY

GND

GND

P+

P-

USB_PWR

P+

P-

USB_PWR

1

Speaker Header
(7-pi n SPK_CI1)
(see p.1, No. 17)

Please connect the
chassis intrusion and the
chassis speaker to this
header.

Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 7)
(SATA3_1:
see p.1, No. 8)
(SATA3_2:
see p.1, No. 11)
(SATA3_3:
see p.1, No. 12)
(SATA3_4:
see p.1, No. 14)
(SATA3_5:
see p.1, No. 13)

USB 2.0 Headers
(9-pin USB1_2)
(see p.1, No. 18)
(9-pin USB3_4)
(see p.1, No. 19)

USB 3.0 Header
(19-pin USB3_5_6)
(see p.1, No. 9)

SATA3_2

SATA3_4

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

SATA3_0

SATA3_1

1

SATA3_3

SATA3_5

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

ese six SATA3
connectors support SATA
data cables for internal
storage devices with up to

6.0 Gb/s data transfer rate.
* If M2_1 is occupied by
a SATA-type M.2 device,
SATA3_0 will be disabled.

ere are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.

Besides four USB 3.0
ports on the I/O panel,
there is one header on this
motherboard. is USB

3.0 header can support
two ports.

20

English

B150M Pro4/Hyper

J_SENSE

OUT2_L

1

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

FAN_SPEED_CONTROL

1 2 3 4

FAN_SPEED_CONTROL

GND

OL

CHA_FAN_SPEED

Front Panel Audio Header
(9-pin HD_ AUDIO1)
(see p.1, No. 23)

is header is for
connecting audio devices
to the front audio panel.

1. High Denition Audio support s Jack Sensing, but the panel wire on the chassis must sup ­port HDA to function correctly. Please follow the instructions in our manual and chassis
manual to install your system.

2. If you use an AC’97 audio panel , please install it to the front panel audio header by the
steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect
them for the AC’97 audio panel .
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and
adjust “Recording Volume”.

Chassis Fan Connectors
(4-pin CHA_FAN1)
(see p.1, No. 24)

(4-pin CHA_FAN2)
(see p.1, No. 10)

CHA_FAN_SPEED

FAN_VOLTAGE

GND

FAN_VOLTAGE

CHA_FAN_SPEED

FAN_SPEED_CONTR

Please connect fan cables
to the fan connectors and
match the black wire to
the ground pin.

CPU Fan Connectors
(4-pin CPU_FAN1)
(see p.1, No. 2)

(3-pin CPU_FAN2)
(see p.1, No. 3)

CPU_FAN_SPEED

FAN_VOLTAGE

GND

FAN_VOLTAGE

GND

is motherboard pro­vides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.

21

English

ATX Power Connector

RRXD1

DDCD#1

RRI#1

#

1

AFD#

ERROR#

PINIT#

GND

SLIN#

STB#

SPD0

SPD1

SPD2

SPD3

SPD4

SPD5

SPD6

SPD7

ACK#

BUSY

PE

SLCT

4

8

(24-pin ATXPWR1)
(see p.1, No. 6)

24

12

is motherboard pro­vides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin

1

13

13.

ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.1, No. 1)

Serial Port Header
(9-pin COM1)
(see p.1, No. 22)

TPM Header
(17-pi n TPMS1)
(see p.1, No. 20)

Print Port Header
(25-pin LPT1)
(see p.1, No. 21)

5

is motherboard
provides an 8-pin ATX

1

12V power connector. To
use a 4-pin ATX power
supply, please plug it along
Pin 1 and Pin 5.

is COM1 header
supports a serial port
module.

RRTS#1

CCTS#1

DDSR#1

TTXD1

GND

DDTR#1

1

is connector supports Trusted

GN D

LAD 0

LAD 3

+3 V

PC IRS T

+3V S B

D

GN

GN D

SER IRQ #

S_P WRD WN #

FRA M E

GN D

LAD 1

LAD 2

SMB _CL K_M AIN

Platform Module (TPM) system,

PC ICL K

which can securely store keys,

1

digital certicates, passwords,
and data. A TPM system also
helps enhance network security,
protects digital identities, and
ensures platform integrity.

is is an interface for print
port cable that allows
convenient connection of printer
devices.

22

English

B150M Pro4/Hyper

4

2.7 M.2_SSD (NGFF) Module Installation Guide

The M.2, also known as the Next G ene rat ion Form Fact or (NGF F), is a sma l l size
and vers atile c a rd edge conn ector t hat aim s to rep lace m PCIe a nd mSATA. The
Ult ra M.2 Soc kets support M.2 PC I E x pre ss module up to Gen3 x4 (32 Gb/s).
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_0 will be disabled.
* If PCI or PCIE2 slot is occupied, M2_1 slot will support M.2 PCI Express module up to
Gen3 x2 (16 Gb/s).

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module
and the screw.

3

Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, nd the corresponding nut

Step 2

2

1

A

BCD

location to be used.

No. 1 2 3 4

Nut Location A B C D

PCB Length 3cm 4.2cm 6cm 8cm

Module Type Typ e2230 Type 224 2 Type22 60 Ty pe 2280

23

English

Step 3

Move the stando based on the
module type and length.

A

BCD

e stando is placed at the nut
location D by default. Skip Step 3
and 4 and go straight to Step 5 if you
are going to use the default nut.
Otherwise, release the stando by
hand.

Step 4

Peel o the yellow protective lm on
the nut to be used. Hand tighten the

A

BCD

stando into the desired nut location
on the motherboard.

Step 5

Align and gently insert the M.2
(NGFF) SSD module into the M.2

A

BC

slot. Please be aware that the M.2
(NGFF) SSD module only ts in one
orientation.

24

ABCD

English

B150M Pro4/Hyper

Step 6

Tighten the screw with a screwdriver
to secure the module into place.

NUT1NUT2D

Please do not overtighten the screw
as this might damage the module.

M.2_SSD (NGFF) Module Support List

Vendor Size Interface Length P/N

ADATA 128GB SATA 3 2280 AXNS381E-128GM-B
ADATA 256GB SATA3 2280 AX NS381E-256GM-B
ADATA 32GB SATA 3 2230 AXNS330E-32GM-B
Crucial 120GB SATA3 2280 CT120M500SSD4
Crucial 240GB SATA3 2280 CT240M500SSD4
Intel 80GB SATA3 2280 Intel SSDSCKGW080A401/80G
Kingston 120GB SATA 3 2280 SM2280S3
Kingston 480GB PCIe2 x4 2280 SH2280S3/480G
Plextor 256GB PCIe 2280 PX- G256M6e
Plextor 512GB PCIe 2280 PX-G512M6e
Samsung 256GB PCIe3 x4 2280 SM951 (MZHPV256HDGL)
Samsung 512 GB PCIe3 x4 2280 SM951 (MZHPV512H DGL)
Samsung 512GB PCIe x4 2280 XP941-512G (MZHPU512HCGL)
SanDisk 128GB PCIe 2260 SD6PP4M-12 8G
SanDisk 256GB PCIe 2260 SD6PP4M-256G
Te am 128GB SATA3 2242 TM4PS4128GMC105
Te am 128GB SATA3 2280 TM8PS4128GMC105
Te am 256GB SATA3 2280 TM8PS 4256GMC105
Te am 256GB SATA3 2242 TM4PS4256GMC105
Tra nscend 256GB SATA3 2242 TS256GMTS400
Tra nscend 512GB SATA3 2280 TS512GMTS800
Tra nscend 512GB SATA3 2260 TS512GMTS600

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com

25

English

M.2 Socket Congurations

M. 2 Typ e SATA 3_0 SATA3_1 SATA3 _2 SATA3_ 3 SATA 3_4 SATA 3_5 PCI1 PCI2

SATA

Type

M.2

PCIE

Type

M.2(x4)

PCIE

Type

M.2(x2)

NO M.2 V V V V V V V V

V= Supported X= Not supported

X V V V V V V V

V V V V V V X X

V V V V V V V V

26

Deutsch

B150M Pro4/Hyper

1 Einleitung

Vielen Dank, dass Sie sich für das B150M Pro4/Hyper von ASRock entschieden
haben – ein zuverlässiges Motherboard, das konsequent unter der strengen
Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung
mit robustem Design, das ASRock Streben nach Qualität und Beständigkeit erfüllt.

Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden
können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert we rden.
Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte
Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten
Sie technische Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer
Webseite spezischen Informationen über das von Ihnen verwendete Modell. Auch
nden Sie eine aktuelle Liste unterstützter VGA-Karten und Prozessoren auf der ASRock­Webseite: ASRock-Website http://www.asrock.com.

1.1 Lieferumfang

•ASRock B150M Pro4/Hyper-Motherboard (Micro-ATX-Formfaktor)

•ASRock B150M Pro4/Hyper-Schnellinstallationsanleitung

•ASRock B150M Pro4/Hyper-Support-CD

•2 x Serial-ATA- (SATA) Datenkabel (optional)

•1 x E/A-Blendenabschirmung

•1 x Schraube für M.2-Sockel

27

Deutsch

1.2 Technische Daten

Plattform

Prozessor

Chipsatz

Speicher

•Micro-ATX-Formfaktor

•Feststoondensator-Design

•Unterstützt die Prozessoren Intel® Core

Celeron® der 6. Generation (Sockel 1151)

•Digipower-Design

•6-Leistungsphasendesign

•Unterstützt Intel® Turbo Boost 2.0-Technologie

•Unterstützt ASRock-Hyper-BCLK-Engine

®

•Intel

B150

•Unterstützt Intel® Small Business Advantage 4.0

•Dualkanal-DDR4-Speichertechnologie

•4 x DDR4-DIMM-Steckplätze

•Unterstützt DDR4 2133 non-ECC, ungepuerter Speicher

•Unterstützt ECC-UDIMM-Speichermodule (Betrieb im

Non- ECC-Modus)
* Weitere Informationen nden Sie in der
Speicherkompatibilitätsliste auf der ASRock-Webseite.
(http://www.asrock.com/)

•Systemspeicher, max. Kapazität: 64GB

•Unterstützt Intel® Extreme Memory Prole (XMP) 2.0

•15-μ-Goldkontakt in DIMM-Steckplätze

TM

i7/i5/i3/Pentium®/

28

Erweiter­ungssteck­platz

Grakkarte

•2 x PCI-Express 3.0-x16-Steckplatz (PCIE1:x16-Modus;

PCIE3:x4-Modus)*
*Unterstützt NVMe-SSD als Bootplatte

•1 x PCI-Express 3.0-x1-Steckplatz (exibles PCIe)

•1 x PCI-Steckplatz

* Falls ein PCI- oder PCIE2-Steckplatz belegt ist, unterstützt
der M2_1-Steckplatz M.2-PCI-Express-Module bis Gen3 x 2 (16
Gb/s).

•Unterstützt AMD Quad CrossFireX

•Integrierte Intel® HD Graphics-Visualisierung und VGA-

Ausgänge können nur mit Prozessoren unterstützt werden,

die GPU-integriert sind.

TM

und CrossFireXTM