Aspire Feedlink Revvo User Manual

Feedlink Revvo Kit User Manual

Read this information leaflet fully before you start using this
product as it contains important information. The notes below
relate to when the device is filled with liquid that contains
nicotine.

This product is intended for adult smokers. This product is not
recommended for non-smokers, young people under the age of 18
years, pregnant or breast feeding women and those experiencing
general ill health.

Wide bore Delrin

Drip cap

Top Chamber

Glass tube

Glass securing ring

Silicone E-juice

bottle

Airflow control ring

ARC coil

Fire button

Threaded

battery cover

Contents:

1* Feedlink mod
1* 2ml Revvo Boost tank

2* Coils (0.10-0.14Ω)

1* Glass tube
11* O-rings
2* Warning card
1* User manual
1* Warranty card

Tank Features

• Bottom fill (fill through the Squonk pin)

• Adjustable airflow

• 2ml capacity

• Innovative ARC(Aspire Radial Coil) technology

• Coil resistance 0.1-0.14Ω

• Wattage range: 70-80W

• Diameter: 24mm

• Length: 41mm

Filling

Squeeze the ejuice bottle inside of the mod to fill the tank.

Coil installation

1. Unscrew and remove the top chamber.

2. Unscrew and remove the mounting screw.

3. Remove the used ARC coil by lifting over the metal pin.

4. Place a new coil over the metal pin, make sure the coil edge
is lined up with the tank.

5. Screw the mounting screw back onto the base hardware.

6. Replace the top chamber.

NB: the mounting screw also acts as a ‘spit-back’ guard.

1 2 3 4 5

Replacing glass

1. Unscrew and remove the glass securing ring from the base
hardware.

2. Pull and remove the used glass tube.

3. Insert a new glass tube.

4. Screw the glass securing ring back onto the base hardware.

Do not let the tank become completely empty. Refill

the tank to avoid dry burning or damage to the
atomizer.

Feedlink mod specifications

Output voltage: 3.0-4.2V
Resistance parameter: 0.1-3.5ohm
Modes: Bypass output
Non-adjustable Wattage/ Voltage
Battery type: Single 18650 high rate discharge battery

(discharge rate ≥35A)

Continuous firing time: 10 seconds
Silicone bottle capacity: 7ml

Safety features

• Automatic cutoff: The continuous fire time is 10 seconds, after

10 seconds of continuous firing the mod will stop firing and the
LED light under the fire button will flash 10 times.

• Battery reverse protection

• Short circuit protection: When the mod detects a short, the

LED light will flash 2 or 3 times.

• Over discharge protection: When the battery level is below

3.2V, pressing the fire button the orange light will flash 15
times.

• Over heat protection: When the temperature of the control

board is above 75 degree Celsius, the mod will shut off and
the LED light will light up blue and orange for 3 seconds.

Operating instructions

1. Installing an 18650 battery into the mod, the LED light will
flash blue and orange 2 times.

2. When the battery level is above 3.8V, the LED light will be
blue only, when the battery level is between 3.5V and 3.8V,
the light will be a mixed color of blue and orange; the orange
light means the battery level is below 3.5V.

3. Click the fire button 5 times rapidly to lock or unlock the
device the LED light will flash blue and orange 3 times to

indicate lock or unlock. When the mod is unlocked, pressing
the fire button the blue or orange LED light will light up
according to the battery level.

Silicone e-juice bottle installation

• Lightly push in the bottle securing cap at the bottom of the

mod.

• Then twist counter-clockwise direction to remove the securing

cap.

• Insert a new silicone e-juice bottle into the plastic carrier

frame, reinsert the frame into the mod then push the knob and

twist clockwise direction to secure.

How to fill the Silicone e-juice bottle?

1. Unscrew and remove the metal cap at the top of the bottle.

2. Add your preferred e-juice into the bottle.

3. Replace metal cap.

Battery installation

1. Invert the Feedlink mod and unscrew the battery cap.

2. Insert an 18650 battery into the battery compartment with
positive end pointing down and negative end pointing up.

3. Screw the battery cap back onto the mod.

IMPORTANT INFORMATION ABOUT USING NICOTINE
CONTAINING E-LIQUIDS

Before using nicotine containing e-liquids the user should read
the following information carefully.

NICOTINE CONTAINING E-LIQUIDS:

Do not use if you are allergic to nicotine or any of the other
ingredients contained within the e-liquid (see manufacturer’s
label for full details).

WARNINGS AND PRECAUTIONS

Nicotine containing e-liquids are not recommended for:

• Non-smokers

• Young people under the age of 18 years;

• Pregnant or breast feeding women; as nicotine is known to

cross the placenta and to be excreted in breast milk;

• Those experiencing general ill health; such as heart disease,
stomach and duodenal ulcers, liver or kidney problems, long

term throat disease or difficulty breathing due to bronchitis,
emphysema or asthma;

• Those who have an overactive thyroid gland or have a
phaeochromocytoma(a tumour of the adrenal gland that can
affect high blood pressure);

• Those who have diabetes, as nicotine may affect your blood
sugar levels.

• Those taking the following medication;

• Theophylline (to treat breathing problems)

• Ropinirole (to treat restless leg syndrome)

• Clozapine (to treat schizophrenia)

POSSIBLE SIDE EFFECTS

If you inhale too much nicotine or use the product too much you
may experience one or more of the following effects:
Feeling faint;
Nausea (feeling sick)
Headache
Coughing
Irritation of the mouth or throat
Dizziness
Stomach discomfort
Hiccups
Nasal congestion
Vomiting (being sick)
Heart palpitations
Abnormal heart rate
If you experience any of these side effects; including any
possible side effects not listed in this leaflet, discontinue using
the product, if the effect(s) continue after you stop use, consult
your doctor or healthcare professional and bring this leaflet to
their attention.

To learn more about your products and how to use,
please visit:

www.aspirecig.com

Shenzhen Eigate Technology Co., Ltd.

Building 3, Xinhongtai Industrial Park, 14 Jian'an Rd,
Tangwei, Fuyong Town, Bao'an District, Shenzhen, China
Tel: [phone] Email: [e-mail]

Manufactured By Eigate MADE IN CHINA