![](/html/ee/eeee/eeee43aef5213e71884a16ff14aac4c66eebedda288547679f58859d237aa91d/bg1.png)
Spring Loaded
510 Connector
Fire button
0.86inch
OLED Screen
Micro USB
charging port
Plus and
Minus buttons
USER MANUAL
Battery cap
Specifications
Wattage range: 1-80W
Voltage range: 0.5-8.0V
Resistance parameter: 0.1-3.5Ω
Output modes: VW/VV/Bypass
Screen type: 0.86inch OLED
Micro USB charging port
Continuous firing time: 10 Seconds
Battery type: Single 18650 high rated discharge battery
Dimensions: 24*48*72.5mm
Temperature Control: N/A
Firmware update: N/A
Protective features
• Automatic Cut Off: The preset continuous fire time is 10
seconds, after 10 seconds of continuous firing, the
screen will display “Over 10S”. Release the fire button
and press again to continue using the mod.
• Short Circuit Protection: When the mod detects a short
or the atomizer attached is below 0.08Ω, the screen will
display “Low Res” for 5 seconds.
• Over Heat Protection: When the control board
temperature rises too high, the screen will display “Too
Hot” for 5 seconds.
• Over Charge Protection When the battery level reaches
4.25V or is fully charged, the mod will stop charging and
the screen will switch off.
• Over Discharge Protection: When the battery level drops
below 3.0V, the mod will stop firing, to remind you it’s
time to charge your mod.
• Battery Reverse Protection: If the battery is installed
incorrectly the mod will stop functioning
1 2
Instructions:
1. Click the fire button 5 times rapidly to lock or unlock the
mod, when the mod is locked, press and hold the fire
button for 3 seconds to shut down the mod completely,
the screen will then display ”System off”. To turn it back
on, press the fire button 5 times rapidly.
2. When the mod is unlocked, pressing the fire button and
plus button simultaneously for 2 seconds will allow you
to switch modes between Wattage, Voltage and Bypass.
When the mod is in wattage or voltage mode, pressing
the plus or minus button will change wattage/voltage
values.
3. When the mod is on, pressing the fire button and minus
button simultaneously for 2 seconds will lock the
adjustment keys, which will be indicated by a lock
symbol on the screen. While in key locked mode, the
wattage/voltage settings cannot be adjusted, but the fire
button still functions. To exit the key locked mode simply
press the fire button and minus button simultaneously.
4. When the mod is on, press the fire button 3 times
quickly will turn the mod into stealth mode, while the
mod is in stealth mode, plus and minus buttons are
locked, fire button still works. To exit stealth mode, click
the fire button 3 times again. (Charging or replacing
battery can also get the mod to exit stealth mode).
5. Screen rotate: Holding the plus and minus button
simultaneously for 2 seconds will rotate the screen
display to help users better read the screen in different
orientation.
6. Language selection: Holding the fire button while
installing the battery will allow you to select your
language preference, the screen will display “EN CH”
click plus or minus button to select the text, press fire
button to confirm. (EN stands for English, CH stands for
Chinese.)
Charging instructions
1.Charging the Cygnet via Micro USB charging port, the
maximum charge current is 1A.
2.When the mod is charging, the screen will display the
battery charge increasing, when the mod is fully
charged, the screen will go off.
3.When the battery is incorrectly installed the mod will not
charge.
4.The battery cannot be replaced while charging. Please
unplug the USB cable before changing your battery.
5.When the mod detects the USB charge voltage is less
than 4.2V, it will stop charging and the screen will
display “CHECK CHARGER”.
* Never use a battery with damaged wrapper, as it is a
safety hazard.
Contents:
1* Cygnet Mod 1* USB cable
1* Warranty Card 1* User Manual
To learn more about your products and how to use,
www.aspirecig.com
please visit:
Shenzhen Eigate Technology Co., Ltd.
Building 3, Xinhongtai Industrial Park, 14 Jian'an Rd,
Tangwei, Fuyong Town, Bao'an District, Shenzhen, China
Tel: +86-755-81499783 Email: service@aspirecig.com
Manufactured By Eigate MADE IN CHINA
+
18