Ashly IS 3.8P, IS 2.8P User Manual

IS Series
Linear Column Loudspeaker Systems.
High-quality speech and music, sleek profile and wide, yet consistent coverage.
S column speakers are a cost-
I
effective way to provide precise vertical dispersion, and consis­tent sound levels front-to-back of a venue… especially when combined with Ashly amps and processors that incorporate Protēa or AquaControl™ software (see page 4).
They fit perfectly next to flat-screens in conference rooms. Combined with an SP
12.1P sub, you can create an effective ”system on a stick” for churches, wedding receptions and corporate events.
Both models ship with flush­mount brackets. Two IS speakers can be joined with an optional joining bracket. Pole and tripod mounts are also available.
Available in Black and White.
❚ Churches
❚ Conference and
huddle rooms
❚ Bars and lounges
❚ Mobile DJ
❚ Distributed audio in HoW,
schools, sports/health clubs and public spaces
❚ Solo/duo acoustic acts
DATA
SHEET
on
PAGE THREE
IS Series
Dual-Impedance Column Speakers
This page intentionally left blank*.
Page 2 of 5
Data Sheet begins on the next page.
*Done so that those fortunate to have printers with
2-sided printing capabilities can print out the Data Sheet
on one sheet of paper.
Page 3 of 5
IS Series
S Series are slim column array
I
speakers designed to deliver high-quality speech and music in venues that require high intelligibility, low physical profile and wide, yet consistent coverage.
They are a cost-effective way to provide vertical pattern control, and consistent sound levels front­to-back of a venue… especially when combined with Ashly amps and processors that incorporate Protēa or AquaControl™ software (see next page).
IS columns fit perfectly next to flat-screens in conference rooms; combined with an SP 12.1P sub, you can create an effective "system on a stick" for churches, wedding receptions and corporate events.
Their durable all metal enclosures will withstand the rigors of portable use, as well as installation and an impedance switch (8 Ω/32 Ω) allows use for both 2/4 speaker or multiple speakers per channel (i.e. distributed) configurations, without loading down the amplifier and without the need for transformers.
Available in two configurations: IS 2.8P 2” x 8 Column and IS 3.8P 3” x 8 Column, they are designed to provide optimum performance when used with Ashly’s Protea or AquaControl-based DSP.
Two speakers may be stacked (using the optional plate) for additional throw where needed.
Add the SP-12.1P 12” Subwoofer for a kicking low-frequency response.
Flush wall brackets are supplied. Other mount options are also available. Available in Black or White
Dual-Impedance Column Speakers
IS 2.8PW
shown with SP 12.1P Subwoofer
Eight IS columns • 32Ω setting @ 50W each Eight IS columns • 32Ω setting @ 50W each
Ashly nXp 4004, 8004,
or ne4250 4-channel
amplifier with Protēa
Eight IS columns • 32Ω setting @ 50W each Eight IS columns • 32Ω setting @ 50W each
8 Ω/32 Ω switch allows use for multiple speakers per channel (i.e.-distributed) configurations, without loading down the amplifier and without the need for transformers.
US toll-free +1.585.872.0010
Sales@Ashly.com • www.Ashly.com
IS 3.8P
IS 2.8P
4 x 400 W @ 4 Ω
Fax +1.585.872.0739
IS Series
Dual-Impedance Column Speakers
Page 4 of 5
Further sonic enhancment with Protêa and AquaControl™ software presets for selected Ashy amplifiers and processors.
IS speakers will please you with their performance and price. But specify…:
❚ nXp series multi-mode amps with Protêa ❚ pēma series Protêa-enabled amps
❚ ne4250pe and ne8250pe network-enabled
amp with Protêa
❚ ne series processors with Protēa ❚ or mXa-1502 mix amp with AquaControl and get:
■ Directivity-weighted, optimized linear
frequency response
■ Universal crossover implementation for use
with subwoofer and full-range speakers
■ FIR-corrected linear phase response above
about ~300 Hz
Optimized linear frequency response and universal crossover implementation only are available on ne24.24m.
The switch that gives you a "distributed" system with up to 32 IS speakers… but without having to use transformers.
IS 2.8 P and 3.8P column speakers are switchable to to 32-ohm mode.
IS 2.8P IS 3.8P
Transducer
Frequency Response (–10dB limits)
Sensitivity (ref 2.83V) Nominal Impedance 8 Ω / 32 Ω switchable 8 Ω / 32 Ω switchable
Maximum Continuous SPL, @ a MIV (continuous / peak)
Maximum Continuous SPL, calculated from power handling (continuous / peak)
Maximum Input Voltage (MIV)
Power Handling 120 W 240 W
Beamwidth
1
1, 2
1, 2, 3
1, 2
4
8 x 2-inch (51 mm) Neodymium
115 Hz – 20 kHz 105 Hz – 19 kHz
88 dB 95 dB
104 dB / 115 dB 113 dB / 124 dB
1, 2, 3
109 dB / 115 dB 119 dB / 125 dB
28 dBV, 25.1 V (equivalent to 80 W into rated impedance)
Horizontal: 190° Vertical: 30°
8 x 3-inch (76 mm) Neodymium
30 dBV, 31.6 V (equivalent to 125 W into rated impedance)
Horizontal: 170° Vertical: 25°
IS 2.8P shown with SP 12.1P subwoofer and IS-PM6B Pole Mount
1) With recommended processing (see previous page)
2) Referenced to 1 m
3) The maximum input voltage (MIV) is determined by no more than a 3 dB change in the frequency response of the loudspeaker system
4) Averaged from 400 Hz to 10 kHz
USER MANUAL
Or download the complete User Manual at
http://ashly.com/wp­content/uploads/2019/ 09/IS_Manual.pdf
Directivity Index (DI)4 14.4 dB 11.8 dB
Directivity Factor (Q)4 2 7.4 15.2
Input Connectors
Mounting Provisions
Enclosure Material Aluminum Aluminum
Dimensions (HxWxD)
Net Weight 6.4 lbs. / 2.9 kg 12.8 lbs. / 5.8 kg
Recommended amplifiers
2 x ¼-inch (6.3 mm) phone jack 1 x 2-position Euroblock
IS-TWM Tilt Wall Mount IS-FWM Flush Wall Mount
Bracket (included)
24.00 in. x 2.76 in. x 3.54 in. 610 mm x 70 mm x 90 mm
Single-ch.: nXp 400 or higher Bridged: nXp 150 or higher
Pema 4125, 4250, 8125, 8250
2 x NL4 SpeakOn 1 x 4-position Euroblock
IS-TWM Tilt Wall Mount IS-FWM Flush Wall Mount
Bracket (included)
31.77 in. x 4.06 in. x 5.12 in. 807 mm x 103 mm x 130 mm
Single-channel: nXp 400 or higher
Bridged: nXp 400 or higher Pema 4125, 4250, 8125, 8250
AW SERIES ARCHITECT & ENGINEERING SPECIFICATIONS
in .txt and MS Word .docx format are available in the
DOWNLOADS section of
http://ashly.com/IS series
AW SERIES 2D AUTOCAD FILES
are available in the DOWNLOADS section of
http://ashly.com/IS series
IS Series
100 1k 10k
110
100
90
80
70
Frequency [Hz]
Sound pre ssure, Leve l [dB]
20 50 200 500 2k 5k 20k
105
95
85
75
Listening Window, Pro cessed
On-Axis, P rocesse d
Frequency [Hz]
On-Axis, P rocesse d
On-Axis, No P rocessing
Frequency [Hz]
On-Axis, P rocesse d
On-Axis, No P rocessing
Frequency [Hz]
Listening Window, Pro cessed
On-Axis, P rocesse d
Page 5 of 5
Dual-Impedance Column Speakers
IS 3.8P Frequency Response (On-Axis) IS 2.8P Frequency Response (On-Axis)
110
105
100
95
90
85
80
Sound pre ssure, Leve l [dB]
75
70
20 50 200 500 2k 5k 20k
100 1k 10k
100
95
90
85
80
75
70
Sound pre ssure, Leve l [dB]
65
60
20 50 200 500 2k 5k 20k
100 1k 10k
IS 3.8P Frequency Response (Listening Window) IS 2.8P Frequency Response (Listening Window)
100
95
90
85
80
75
70
Sound pre ssure, Leve l [dB]
65
60
20 50 200 500 2k 5k 20k
100 1k 10k
Two
IS 2.8PWs
with IS-JP2
Joining
Bracket
IS-PM6B
Pole Mount
IS-PM6B
Pole Mount
SP 12.1PB SubwooferSP 12.1PW Subwoofer
IS-TR7B
Tripod
Mount
Flush Mount brackets (included with IS 2.8Ps and IS 3.8Ps)
IS-JP2B Join-
ing Bracket
shown on two
IS 2.8PWs
IS-TWM Tilt/Swivel Mount for IS
2.8Ps and IS 3.8Ps
Ashly Audio, Inc. • 847 Holt Road • Webster, NY
USA • US toll-free +1.585.872.0010
Fax +1.585.872.0739 •Sales@Ashly.com
www.ashly.com
Loading...