Ashland I-175XL User Manual

I-175

PARTS MANUAL

Version 4-04

Ashland Industries Inc.
1115 Rail Drive
P.O. Box 717
Ashland, WI. 54806
Ph: 877-634-4622
Ph: 715-682-4622
Fx: 715-682-9717
www.ashlandind.com

Toll Free

Model I-175 Scraper

HOW TO ORDER PARTS:

IMPORTANT

Parts must be ordered through your local authorized ASHLAND dealer.
Be sure to state MODEL and SERIAL NUMBER of your machine, PART NUMBER, DESCRIPTION
and QUANTITY needed.

Unless this is done, we cannot provide prompt service or assure shipment of the correct parts.

Ashland Industries weldable replacement parts are availabe to rebuild, modify or
update your scraper to current factory specifications.

INDEX

Page 3. Operators and Maintenance Instructions
Page 4. Safety Guidelines
Page 5. Illustration - Assembly
Page 6. Illustration - Gooseneck Frame Assembly
Page 7. Illustration - Apron Assembly
Page 8. Illustration - Bowl and Frame Assembly
Page 9. Parts List - Bowl and Frame
Page 10. Illustration and Parts List - Push Off Gate Assembly
Page 11. Illustration and Parts List - Pole and Axle Assembly
Page 12. Illustration and Parts List - Front Wheel and Hub Assembly
Page 13. Illustration and Parts List - Rear Wheel and Hub Assembly
Page 14. Illustration and Parts List - Hydraulic Cylinder 4” x 13” Right
Page 15. Illustration and Parts List - Hydraulic Cylinder 4” x 13” Left
Page 16. Illustration and Parts List - Hydraulic Cylinder 5” x 20” Lift Cyl
Page 17 Illustration - Hydraulic Cylinder 4-1/2” x 60”
Page 18. Parts List - Hydraulic Cylinder 4-1/2” x 60”
Page 19. Illustration - Hydraulic Circuit
Page 20. Parts List - Hydraulic Circuit
Page 21. Ilustration and Parts List - Hydraulic Valve
Page 22. Counterbalance Valve
Page 23. Warranty Statement

2

OPERATORS AND MAINTENANCE INSTRUCTIONS

This scraper is a durable piece of equipment and with proper care will yield many years
of trouble free operation. The scraper requires a power source with TWO 4 way (double
acting) hydraulic control valves.

The scraper should be greased at all points where grease fittings are provided. Connect
hydraulic hoses to the tractor and retract lift cylinders to REMOVE TRANSPORT LOCK
PINS (point A), then extend and retract all cylinders several times to force out any air from
the hydraulic cylinders and lines. Check the oil levels in the tractor hydraulic system and
add to maintain the proper level. Care should be used when adding oil or when discon­necting any oil line to keep all dirt out of the oil as dirt is a major factor in the failure of
hydraulic components.

When the scraper is placed into operation, the operator will have to “feel out” the
amount of depth of cut to obtain maximum loading efficiency. This is usually accomplished
by taking a lesser and more uniform cut; however, some soil conditions such as loose sand
may require a “pumping action” obtained by taking successive deep cuts and lifting out of
cut as the tractor begins to lose power or traction.

1. After 10 hours work, all bolts should be checked and tightened if necessary.

2. Every 10 hours all grease fittings should be lubricated.

3. After 50 hours work, all bolts should be rechecked and tightened if necessary.
Check wheel bearings and adjust if necessary.

4. After 300 hours work, clean and repack wheel bearings and replace, if necessary,
cutting edges, worn pins, etc.

3

SAFETY SIGNAL WORDS

Note the use of the signal words DANGER, WARNING and CAUTION with the safety mes­sages. The appropriate signal word for each has been selected using the following guide­lines:

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in

death or serious injury. This signal word is to be limited to the most extreme situa­tions typically for machine components which, for functional purposes, cannot be
guarded.

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in

death or serious injury, and includes hazards that are exposed when guards are
removed. It may also be used to alert against unsafe practices.

CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in

minor or moderate injury. It may also be used to alert against unsafe practices.

GENERAL SAFETY GUIDELINES

Safety of the operator is one of the main concerns in designing and developing a new piece
of equipment. Designers and manufacturers build in as many safety features as possible.
However, every year many accidents occur which could have been avoided by a few sec­onds of thought and a more careful approach to handling equipment. You, the operator,
can avoid many accidents by observing the following precautions in this section. To avoid
personal injury, study the following precautions and insist those working with you, or for
you, follow them.

Replace any CAUTION, WARNING, DANGER or instruction safety decal that is not readable
or is missing. Location of such decals is indicated in this booklet.

Do not attempt to operate this equipment under the influence of drugs or alcohol.

Review the safety instructions with all users annually.

This equipment is dangerous to children and persons unfamiliar with its operation. The
operator should be a responsible adult familiar with farm machinery and trained in this
equipment’s operations. Do not allow persons to operate or assemble this unit

until they have read this manual and have developed a thorough understanding
of the safety precautions and of how it works.

To prevent injury or death, use a tractor equipped with a Roll Over Protective System
(ROPS). Do not paint over, remove or deface any safety signs or warning decals on your
equipment. Observe all safety signs and practice the instructions on them.

Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely,
is in question - DON’T TRY IT.

4

ILLUSTRATION * ASSEMBLY

HYDRAULIC
CLYINDER

PUSH OFF GATE

BOWL FRAME

HYDRAULIC
CYLINDER

APRON

A

FRONT FRAME

5

GOOSENECK FRAME ASSEMBLY

PARTS LIST

GOOSENECK FRAME ASSEMBLY

MODEL I-175

KEY NO. PART NO. DESCRIPTION

1. A17507 Gooseneck Frame

2. AFB-00054 Bolt, 1/2” NC x 3-1/2” Lg.

3. 14505 Grease Zerk - Straight

4. A17508 Pin, Frame Attach

5. ----- Hair Pin

6. AFB-00018 Bolt, Transport Lock, 1” NC x 3”
AFN-00012 Nut: 1” NC

7. AFB-00022 Bolt, 7/8”NF x 4-1/2” Lg. Grade 5

8. 7597 Nut, 7/8”NF

9. 8125 Lockwasher 7/8”

10. A14002 Cast Socket Half - Rear

11. A14003 Cast Socket Half - Front w/Zerk Hole

12. A2206 Grease Zerk - Long Shank

13. A17509 Bushing, 2-3/4” OD x 2-1/4” ID x 2” Long

6

APRON ASSEMBLY

PARTS LIST

APRON ASSEMBLY

MODEL I-175

KEY NO. PART NO. DESCRIPTION

1. A17505A Apron
A17505B Apron Model, s/n 17719 & up

2. AFN-00018 Self Lock Nut, 1-1/2” NF

3. A17506A Shoulder Pin, 2-1/4” x 1-1/2”, w/ zerk in head

----- Bolt, 1-1/2”NF x 6” Lg., for s/n 17719 & up

4. 14505 Grease Fitting, 1/8” NPT

5. A10155 Bushing, 1-1/2” OD x 1” ID x 1” Lg.

6. A16027 Bushing, 2” OD x 1-1/2” ID x 2” Lg.

7