Arylic Up2Stream Pro User manual

Up2Stream Pro User Manual

R47 10K

DGND

1. Introduction

Up2Stream Pro is a WiFi and Bluetooth audio receiver board that can be easily integrated to your existing audio hardware devices to enable
them with network and bluetooth streaming capability. With Up2Stream installed and using 4STREAM app, it allows you to stream music from
cloud, phone, NAS, and more streaming services, such as spotify, deezer, qobuz, tidal..etc. It also support multiroom and multizone control

and music playback.This receiver board is perfect to build your own Audio Source Receiver, Wireless Audio Amplier, Wireless Seapker,

Wireless Speaker Forniture & Mulitroom Audio System.

2. What's in the box

UpStream Pro

7pin cable

4pin cable

2pin cable

WiFi Antenna

User Manual

More accessories coming soon at www.arylic.com

DAC

Acrylic Casing

External SPDIF Board

3. Interface

B DC F

P

E

G

KLMO N

*P Power Button: Short press to power off and on; When in WiFi mode, long press (press and hold the button for more than 5 seconds) to

reset WiFi settings and enter the paring mode; When in Bluetooth mode, long press to terminate current connection.

Further Notes

PH2.0-7P: SPDIF, MCLK, IIS_DATA, BCLK, LRCK, GND,

D

VCC_3V3:

This is the digital audio output extension. For the IIS, BCLK is

2.8MHz, the LRCK is 44.1KHz, the MCLK is 11.288MHz, the DOUT

following the standard IIS data

format and have 16 bits depth. The system is running in master

mode, you should make sure the IIS port of connected device is

running in slave mode.

PH2.0-4P: 3V3, GND, .....

E

GPIO2 and GPIO1 is used to connect a coding key, should be used

for volume control.

PH2.0-11P: 3V3, .......

F

KEY is used for external buttons, refer to the circuit right for key

definitions. The LED pins are used to extend the LED, and are

common-anode connected. You should connect 3.3V to a current

limit resister and then to LED and then to the pin. TX/RX are UART

interface to send events and receive controls.

4. Connection Diagram

External DAC Board

B

WiFi Antenna

LED

C

D

H

I

J

IIS-out,SPDIF-out

E

GPIO

Extension Port

F
G

IR Receiver

BT Antenna

H

On-board Bluetooth Antenna

I
J

5V/1A Power Input

Mirco USB(Power/USB DAC)

K

External Button Board

3.5mm Line-Out

L

3.5mm Line-In

M
N

USB

O

LAN

P

Power Button

*

LED Status :
Power on :White light on
System Booting :White light blink fast
Ready for Connection: White light blink slowly
Ready to play : White light on steady
Bluetooth Pairing: Blue light blink
Bluetooth Connected :Blue light on steady
USB Playback :Red light on
Line in Playback: Green LED Steady on

VDD3V3

KEY

C27

0.1uF

External Knob Board

R64

100R

R60

DGND

1K

R61

2.2K

R62

3.6K

R63

5.6K

R65

8.2K

R66

12K

R67

18K

R68

27K

R69

47K

R70

100K

MODE

PLAY/PAUSE

NEXT

PREV

VOL+

VOL-

MUTE

NUM1

NUM2

NUM3

NUM4

5. How To Use

5.1 App download

Download the 4STREAM application from App Store for iOS based devices and Google Play Store for
Android based devices.
The application supports English, Spanish, French, German, Italian, Portugese, Korean, Simplified
Chinese,Traditional Chinese and Japanese

5.2 Connection

1. Power the device.

2. Direct Mode: If you don’t have router, please choose direct mode, then you
can play your music from your storage from 4STREAM app .

3.Network Mode : Connect your phone to SoundSystem WiFi.

3.1. Go for mobile device WLAN settings> Connect
mobile device to WiFi hotspot SoundSystem_xxxx you will see a WiFi logo
(short press the reset button if the Wi-Fi hotspot is not found)

3.2. Open the 4STREAM application, follow the guides

3.3 Choose the 2.4G network( rst time connection require connect your router

2.4G channel), enter router password>wait for the device to be congured.

* For multiple units connecting to same router, router password will be saved .
*If change router or router password, please press WiFi reset button on the
product .

5.3 Connection via LAN
Plug in the wired cable to the RJ45 Ethernet, the device will show on the app in about 10 seconds. (Note: the cell phone and the device must
be in the same network)

.

*Attention for Android users
Different brand mobile phones may ask you to allow
to use SoundSystem WiFi network, please choose
yes, if not, you may not able to set up successfully .
It may also ask you to authorize other things, please
choose yes or it may affect your use.

5.4 Bluetooth

To use bluetooth ,please swtich to bluetooth via
app or by remote controller,then find bluetooth
device SoundSystem_XXXX from your phone
bluetooth setting and pair it .

5.5 USB audio

Connect the Up2Stream Pro to your PC with USB cable (make sure it’s a data cable including the
signal wires). The PC will automatically discover a USB sound card, and when you activated it as the
system main output, the PC will send the audio output over Up2Stream Pro in digital (44.1KHz/16bits).
You can stream to other Up2Stream devices over multiroom connection.
NOTE: there’s about 3 seconds delay for multiroom slave devices.

5.6 Up2Stream DSP Audio Effects Tool (Sell Separately)

Connect the Up2Stream device to your PC with USB cable (make sure it’s a data cable including the signal wires). And open
the program Up2Stream DSP Tool (only support Windows.), and you can tune audio effects conveniently, including Music Noise
Suppressor, Virtual Bass, Stereo Widener, Exciter, 10 bands EQ, etc. After editing the audio effects, you can save the changes to the
device so the tuned effects will remain. You can get more information from our website www.arylic.com，or from the Up2Stream
DSP Tool manual.

5.7 Firmware update

The application will notify you in app when there is a

new rmware version available.It's recommended to
update rmware whenever available as this might not

only correct bugs or improve security,but also can
add new features or services.

6. Specication

Wireless network IEEE802.11 b/g/n 2.4G

Connectivity

Bluetooth Distance 10M

Power Input *

Audio output

* Warning: Up2Stream Pro must use 5V-1A DC input, higher voltage power supply may damage the board.

Ethernet Single 10/100M RJ45

Bluetooth 5.0,SBC/AAC

USB Host Play USB music

5V-1A/2 pin connector

5V-1A micro USB input

Analog 3.5mm/4 pin connector

Digital IIS

SPDIF

Frequency response 20Hz to 20kHz

Audio Input Analog 3.5mm/4 pin connector/Mirco USB

SNR 91dB

THD 0.03%

Music Format FLAC/MP3/AAC/AAC+/ALAC/APE/WAV

Decoding Up to 24bit/192kHz

Protocols AirPlay, DLNA, UPnP, Spotify Connect, Qplay

Dimensions

Accessory

87.6*49.6*15mm

4Pin 220mm 2.0 Cable,Internal WiFi Antenna
220mm,7Pin 220mm 2.0 Cable, 2Pin 220mm
Power Cable, User Manual

Scan the QR codes below for more

Complete User Manual

Support: [e-mail]

www.arylic.com

4STREAM App Facebook: arylicme YouTube:Arylic

Up2Stream Pro V3.1.0