Aruba AP-205 Data sheet
DATA SHEET
ARUBA 200 SERIES
ACCESS POINTS
Bringing 802.11ac to the masses
Multifunctional and aordable Aruba 200 series
802.11ac wireless APs maximize mobile device
performance in medium-density enterprise
Wi-Fi environments.
These compact and cost-eective dual-radio APs deliver
wireless data rates of up to 867 Mbps to 5-GHz devices with
802.11ac technology leveraging two spatial MIMO streams
while simultaneously supporting 2.4-GHz 802.11n clients with
data rates of up to 300 Mbps.
The AP-205 and IAP-205 models feature four integrated
omni-directional downtilt antennas, while the AP-204 and
IAP-204 support external detachable dual-band antennas
using two RP-SMA antenna connectors.
UNIQUE BENEFITS
• Wi-Fi client optimization
- To eliminate sticky client behavior while users roam, 200
series APs feature patented ClientMatch technology,
which continuously gathers session performance metrics
from mobile devices.
- If a mobile device moves away from an AP or if RF
interference impedes performance, ClientMatch
automatically steers the device to a better AP.
• Advanced Cellular Coexistence (ACC)
- ACC lets WLANs perform at peak eciency by
minimizing interference from 3G/4G LTE networks,
distributed antenna systems and commercial small
cell/femtocell equipment.
• Quality of service for unied communication apps
- The 200 series APs support priority handling and policy
enforcement for unied communication apps, including
Microsoft Lync with encrypted videoconferencing, voice,
chat and desktop sharing.
CHOOSE YOUR OPERATING MODE
The 200 series APs oer a choice of operating modes to meet
your unique management and deployment requirements.
• Controller-managed AP or Remote AP (RAP) running
ArubaOS. When managed by Aruba Mobility Controllers,
200 series APs oer centralized conguration, data
encryption, policy enforcement and network services,
as well as distributed and centralized trac forwarding.
Please refer to the Aruba Mobility Controller data sheets
for more details.
• Aruba Instant AP running InstantOS. In Aruba Instant
mode, a single AP automatically distributes the network
conguration to other Instant APs in the WLAN. Simply
power-up on Instant AP, congure it over the air, and
plug in the other APs – the entire process takes about
ve minutes.
For large installations across multiple sites, the Aruba
Activate™ service signicantly reduces deployment time by
automating device provisioning, rmware upgrades, and
inventory management. With Aruba Activate, Instant APs are
factory-shipped to any site and congure themselves when
powered up.
If WLAN requirements change, a built-in migration path
allows 200 series Instant APs to become part of a WLAN that
is managed by a Mobility Controller.
DATA SHEET
ARUBA 200 SERIES ACCESS POINTS
AP-200 SERIES SPECIFICATIONS
• AP-205 and IAP-205
- 2.4-GHz (300 Mbps max rate) and 5-GHz (867 Mbps max
rate) radios, each with 2x2 MIMO and four integrated
omni-directional downtilt antennas.
• AP-204 and IAP-204
- 2.4-GHz (300 Mbps max rate) and 5-GHz (867 Mbps max
rate) radios, each with 2x2 MIMO and two combined,
diplexed external RP-SMA antenna connectors.
ADVANCED FEATURES
• RF management
- Adaptive Radio Management (ARM) technology
automatically assigns channel and power settings,
provides airtime fairness and ensures that APs stay clear
of all sources of RF interference to deliver reliable,
high-performance WLANs.
- The 200 Series APs can be congured to provide
part-time or dedicated air monitoring for spectrum
analysis and wireless intrusion protection, VPN tunnels
to extend remote locations to corporate resources, and
wireless mesh connections where Ethernet drops are
not available.
• Spectrum analysis
- Capable of part-time or dedicated air monitoring, the
spectrum analyzer remotely scans the 2.4-GHz and 5-GHz
radio bands to identify sources of RF interference.
• Security
- With an OpenDNS service subscription, Aruba Instant
RAPs deliver integrated web ltering, malware and botnet
protection to every device connected to the WLAN.
- Integrated Trusted Platform Module (TPM) for secure
storage of credentials and keys
- SecureJack-capable for secure tunneling of wired
Ethernet trac.
OPERATING MODES
• Aruba Instant AP
• Mobility Controller-managed AP
• Remote AP (RAP) for branch deployments
• Air monitor (AM) for wireless IDS, rogue detection
and containment
• Spectrum analyzer, dedicated or hybrid
• Secure enterprise mesh
WIRELESS RADIO SPECIFICATIONS
• AP type: Indoor, dual radio, 5-GHz 802.11ac and 2.4-GHz
802.11n 2x2:2
• Software-congurable dual radio supports 5 GHz (Radio 0)
and 2.4 GHz (Radio 1)
• 2x2 MIMO with two spatial streams and up to 867 Mbps
wireless data rate
• Support for up to 255 associated client devices per radio,
and up to 16 BSSIDs per radio
• Supported frequency bands (country-specic
restrictions apply):
- 2.4000 GHz to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
• Available channels: Dependent on congured
regulatory domain
• Dynamic frequency selection (DFS) optimizes the use of
available RF spectrum
• Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division
multiplexing (OFDM)
• Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
• Transmit power: Congurable in increments of 0.5 dBm
• Maximum (aggregate, conducted total) transmit power
(limited by local regulatory requirements):
- 2.4-GHz band: +21 dBm (18 dBm per chain)
- 5-GHz band: +21 dBm (18 dBm per chain)
• Advanced Cellular Coexistence (ACC) minimizes
interference from cellular networks
• Maximum ratio combining (MRC) for improved
receiver performance
• Cyclic delay/shift diversity (CDD/CSD) for improved
downlink RF performance
• Short guard interval for 20-MHz, 40-MHz and
80-MHz channels
• Space-time block coding (STBC) for increased range and
improved reception
• Low-density parity check (LDPC) for high-eciency error
correction and increased throughput
• Transmit beamforming (TxBF) for increased reliability in
signal delivery
DATA SHEET
ARUBA 200 SERIES ACCESS POINTS
• Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 300 (MCS0 to MCS15)
- 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2)
• 802.11n high-throughput (HT) support: HT 20/40
• 802.11ac very high throughput (VHT) support:
VHT 20/40/80
• 802.11n/ac packet aggregation: A-MPDU, A-MSDU
ANTENNAS
• AP-204/IAP-204: Two RP-SMA connectors for external dual
band antennas. Internal loss between radio interface and
external antenna connectors (due to diplexing circuitry):
1.5 dB in 2.4 GHz and 3.0 dB in 5 GHz.
• AP-205/IAP-205: Four integrated downtilt omni-directional
antennas for 2x2 MIMO with maximum antenna gain of
4.0 dBi in 2.4 GHz and 6.0 dBi in 5 GHz. Built-in antennas
are optimized for horizontal ceiling mounted orientation
of the AP. The downtilt angle for maximum gain is
approximately 30 degrees.
OTHER INTERFACES
• 10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Ecient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3af PoE
• DC power interface, accepts 1.7/4.0-mm center-positive
circular plug with 9.5-mm length
• Visual indicators (LEDs):
- Power/system status
- Ethernet link status (ENET)
- Radio status (two; RAD0, RAD1)
• Reset button: factory reset (during device power up)
• Serial console interface (RJ-45)
• Kensington security slot
POWER
• Maximum (worst-case) power consumption: 12.5 watts
(PoE) or 11.7 watts (DC)
• Maximum (worst-case) power consumption in idle mode:
8.4 watts (PoE) or 7.7 watts (DC)
• Direct DC source: 12 Vdc nominal, +/- 5%
• Power over Ethernet (PoE): 48 Vdc (nominal)
802.3af-compliant source
• Power sources sold separately
• When both power sources are available, DC power
takes priority
MOUNTING
• Included with AP:
- Mounting brackets (2) for attaching to 9/16-inch or
15/16-inch T-bar drop-tile ceiling
• Spare mounting kit:
- AP-220-MNT-C1: Aruba AP mount kit contains two
ceiling-grid rail adapters for at rails
• Optional mounting kits:
- AP-220-MNT-C2: Aruba AP mount kit contains two
ceiling-grid rail adapters for Interlude and Silhouette
style rails
- AP-220-MNT-W1: Aruba AP mount kit contains one basic
at-surface wall/ceiling mount bracket
- AP-200-MNT-W2: Aruba AP mount kit contains one
secure at-surface wall/ceiling mount cradle
MECHANICAL
• Dimensions/weight (unit, excluding mount accessories):
- 150 mm x 150 mm x 41.5 mm (W x D x H)
- 380 g
• Dimensions/weight (shipping):
- 190 mm x 187 mm x 57 mm (W x D x H)
- 550 g
ENVIRONMENTAL
• Operating:
- Temperature: 0° C to +40° C (+32° F to +104° F)
- Humidity: 5% to 95% non-condensing
• Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)
REGULATORY
• FCC/Industry of Canada
• CE Marked
• R&TTE Directive 1995/5/EC
• Low Voltage Directive 72/23/EEC
• EN 300 328
• EN 301 489
• EN 301 893
• UL/IEC/EN 60950
• EN 60601-1-1 and EN 60601-1-2
For more country-specic regulatory information and
approvals, please see your Aruba representative.
RELIABILITY
MTBF: 711,187 hours (81.2 years) at +25° C
operating temperature
Loading...