Page 1
ADW5607
OPERATION MANUAL
APPLIANCES
FOR LIVING
Page 2
Congratulations, you are now the proud owner of an ARTUSI cooking appliance.
Thank you for purchasing ARTUSI and welcome to the ARTUSI Family.
This instruction manual has been specially created to inform you of the
full range of features your ARTUSI appliance has to offer and serves as an
introduction to getting the very best out of your ARTUSI appliance.
Dear Artusi Customer, please read this user manual carefully before using the
product and, keep it permanently at your disposal.
Note: This user manual is prepared for more than one model. Some of the
features specified in this Manual may not be available on your appliance.
All our appliances are only for domestic use, not for commercial use. Products
marked with (*) are optional.
We present detailed information on each of the features your ARTUSI appliance
consists of. Once you have read this section you will be able to choose the
most appropriate settings for your appliance when cooking different types of
food.
We ask you to read the instructions in this booklet very carefully as this
will allow you to get the best results from using your appliance. KEEP THE
DOCUMENTATION OF THIS PRODUCT FOR FUTURE REFERENCE.
TO REGISTER YOUR PRODUCT WITH ARTUSI, PLEASE FILL OUT THE WARRANTY CARD
AT THE END OF THIS BOOKLET AND POST IT TO: REPLY PAID 83617
LEICHHARDT NSW 2040
“THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE
REGULA TIONS FORCE AND ONLY USED IN A WELL VENTILATED
SPACE. READ THE INSTRUCTIONS BEFORE INSTALLING OR USING THIS
APPLIANCE”
“Conforms with the WEEE Regulations.”
Page 3
This Operation Manual is supplied together with the "Installation Manual".
Important note!
These operation instructions must be properly kept
The model mentioned this manual may not be sold on every market, and may vary at any time.
The models and specifications of the products sold in your country must be known dearly.
.
Version No.:20211104
Model No.: ADW5607B & ADW5607X
Page 4
Page 5
General dish rack design.
Designed for different
dishes.
More applicable to the
demands of different
users, and more
convenient to arrange
the dishes.
All-round spray system
0
360
complete
removal of dirt.
BLDC motor, low power
consumption, high
hydraulic force, and
capable of removing
all the dirt.
Fashion appearance Match
with the kitchen style freely
The dishwasher appearance
is featured by the modern
and fashion shape and the
decent color.
Outstanding cleaning effect.
Perfect high-temperature
and clean washing. The
dishwasher is good at
eliminating the animal fat
that is hard to clear. The oil
stains are cleared easily with
the special dish washing
powder and the powerful
water flow of high spray
height after the fat is melted
with high-temperature water.
Drawer-type design.
Drawer-type structure design, facilitating the installation and maintenance.
Owing to the drawer-type design, this product has the more reasonable
installation space, is more convenient to install, and is easy and convenient to
repair and maintenance as a whole.
Enjoy washing
Enjoy high-quality life
Realize your high-style life precisely, and endow the special
concept to every type of product of the same family.
Please read this manual carefully in order to help the safe and comfortable use
of the product. For the safe use of the product, the safety precautions and other
instructions in this manual must be read carefully before operating the product
.
Page 6
1
Page 7
Catalog
Safety and Warning
Dish Maintenance
Packing List.
Part name
..............................................................................................
............................................................................ ....
...................................................................................... ...
......................................................... ......... .....
2
5
6
7
1 0
11-15
19
20-21
9
24
Product Specifications
Installation Precautions
Installation Guidelines
Instructions
Cutlery basket
Basket and Cup holder
Place the dishes in the drawer
Water hardness is introduced..................................................................23
Washing procedure is introduced
Adding of Washing Agent.........................................................................25
...........................................................................................16
.....................................................................................
........................................................................
...................................................................
................................................................
...........................................................
.........................................................22
....................................................
.....
Adding of Rinse aid..............................................................................
29
Cleaning and Maintenance
Troubleshooting
Occurrence of Failure
....................................................................................
................................................................
...........................................................................
30
34
36
Failure Diagnosis
Data of Washing Program
Technical Data
Repair and Service
1
....................................................................................
....................................................................
.........................................................................................
...................................................................
.... 42
、43
38
40
41
Page 8
Important safety instructions
The well-designed dishwasher can operate safely during the normal use.
Instructions to the user
The following operating methods must be kept in mind during the use of dishwasher.
Important safety instructions
Warning!- During the use of dishwasher, the basic precautions, including but not limited to the
following principles, must be observed:
Read this manual completely before operating the dishwasher.
For the product over the warranty period, the after-sales service personnel can offer
the paid service, and the charge (over-warranty charge) includes the costs of both
labour and parts. Every payment made by the user is charged according to the uniform
Abide by the instructions in this manual, and minimize the fire or explosion risks in order to avoid
property damage or personal injury.
The dishwasher is just used for the purpose for which this user guide and quick guidance is
intended.
The dishwasher just applies to home use and following similar situations:
-Kitchens of shops, office areas or other work environment; Farm houses;Guests living in the hotels,
motels or other living environment.
Knives and other utensils with sharp points must be loaded in the basket with their points down or
placed in a horizontal position.
The household dishwasher shall just use the suggested washing agent and rinse aid which must be
placed out of reach of any child. Every time after washing, it is required to check if the washing
agent feeder is drained completely.
To place the dishes in the dishwasher, it is forbidden to scratch the inner cover of dishwasher with
the sharp dishes, and the handles of sharp handles must be kept upward in order to avoid hand
cutting. During and after washing, the strainer (at the bottom of drawer) must not be touched by
hand in order to avoid hand bum.
The dishwasher must not be operated before all the control panels are closed.
after-sales charging standard offered by the repairer, and invoiced by the repairer;
otherwise, the user can reject the payment.
The control button must not be modified without permission.
It is forbidden to use the dishwasher for other purposes, or seat or on the drawer or dish rack of
the dishwasher.
The door should not be left in the open position since this could present a tripping hazard.
The foldable cup tray is used to carry tea cups, glass cups and kitchenware. When the foldable cup
tray is placed in the dishwasher, it is forbidden to lean on the tray, or use the tray to support the
body weight.
In order to reduce the personal injury risk, the children are forbidden to play in or above the
dishwasher.
The dishwasher door must be dismantled before the old dishwasher is disassembled or
abandoned.
Some washing agents of dishwasher are strongly basic. The unexpected swallowing of washing
agent may be very hazardous. Skins and eyes shall be protected from washing agent. When the
dishwasher is opened, the children must be far away from the dishwasher. Every time after
washing, it is required to check if the washing agent feeder is drained completely.
The maximum number of place settings to be washed: 7 sets of.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
After installation, Appliance can be unplug easily.
Correct Disposal of this product:This marking indicates that this product should not
be disposed with other household wastes throughout the El-J. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the retailer
where the product was purchased. They can take this product for environmental safe
recycling.
2 43
Page 9
Repair and Service
Warranty instructions of dishwasher
Dear users,
Thanks for your using the dishwasher. The Company will offer the following service in
accordance with the relevant provisions of the Law of the People's Republic of China on
Safeguarding the Consumer Rights and Interests and the State Bureau of Quality and
Technical Supervision and on the basis of the warranty instructions and Invoice:
One-year free warranty service is offered for whole machine.
Three-year free warranty service is offered for main components (including main control panel or
program controller, heater, washing pump and water drain pump).
The following cases are outside with the free service scope, for which the paid repair and full-life
service can be offered:
[A].The warranty certificate and invoice cannot be offered;
[B]. The invoice is altered;
[C]. The damage is caused by accident or improper use;
[D]. The damage is caused by the repair unapproved by the Company;
[E].The machine is over the valid period of warranty service, and can be reused after repair.
3-month warranty service is offered for the machine for public use installed in such place as
institution, shop, school and hotel, and one-year warranty service is offered for main components.
The valid period of warranty service starts from the date when the invoice is issued, deducting the
time occupied by repair and the waiting time for any part that is unavailable.
Within the valid period of warranty service, the consumer can repair, replace or return
the machine on the basis of invoice and warranty certificate.
In case of any performance failure within 7 days after the machine is sold, the consumer can
return, replace or repair the machine.
In case of any performance failure within 15 days after the machine is sold, the
consumer can replace or repair the machine.
42 3
Important safety instructions
Installation
Before operating the dishwasher, it is necessary to install the dishwasher in accordance with
the installation manual. If your dishwasher is not provided with installation manual, please
call the after-sales service phone. Our after-sales personnel will offer the assistance.
The installation and repair of dishwasher must be performed by the professional technicians.
The power wire that is damaged shall be replaced by the professional technicians.
The dishwasher must be fastened with screws in the cabinet. The dishwasher that is not
fastened may shake, whidl may result into dishwasher damage or personal injury.
If the dishwasher is damaged or fails, any component is dismantled, any part is missing or
damaged, or any power wire or plug is damaged, the dishwasher must not be used any
more.
Never store gasoline or other flammable gas or fluid in any dishwasher accessory.
The dishwasher shall be conneded to the power source with suitable rated voltage and
earthing protection in order to prevent the circuit from overloading.
The power wire must be fastened at the designated place in order to prevent the power wire
from damage or canying any load due to treading or stumbling.
The dishwasher must not be installed or stored in the place or outdoors at temperature
below 00 .
The dishwasher must not be conneded to the power source with power extension wire or
portable power socket (such as multi-hole socket).
The dishwasher must be provided with earthing protection. In case of failure or damage, the
earthing protection provides a current leaking patch with minimum resistance so that the
electric shock risk is reduced obviously. The plug must be inserted into the reliably earthed
socket that is installed according to the local laws and regulations. Waming- The electric
shock may be caused if the equipment earthing wire is not connected properly. If you doubt
the reliable earthing of dishwasher, please contact the experienced electrician or after-sales
service personnel for site test. The power plug of dishwasher must not be modified without
permission. If the plug does not match the socket, please contact the experienced electrician
to install the suitable socket.
If the dishwasher is installed as a permanently connected equipment: Earthing instructions-
The dishwasher must be connected to the permanent metal earthing wire or the ear-thing
wire must be connected to the equipment earthing terminal or connector on the dishwasher
through the electric wire.
When installing, the power cord socket must be installed \There the power cord is easily
accessible.
There is an air outlet under the door of the dishwasher, so the bottom of the door should
not be blocked by the carpet.
Page 10
Important installation instructions
Installation
Before the dishwasher is cleaned or repaired, the power plug of dishwasher must be unplugged.
To power off the dishwasher, the power plug must be disconnected in order to avoid damage.
It is forbidden to pull the power wire or the connection between the power wire and the socket.
Unless specially stipulated in this user guide, it is forbidden to repair or replay any part of
dishwasher, or try to repair the dishwasher. When necessary, please contact the after-sales service
department for repair, or refer to the section "Repair and Service" for relevant information.
The floor around the dishwasher shall be kept clean and dry in order to avoid hazard due to
slipping.
The flammable materials must not be stored around or under the dishwasher, such as lint, paper,
duster clothes or chemicals.
Operating precautions
The drawer must not be opened when the dishwasher is operating.
The dishwasher can be used only when the motor, strainer, filter and spray arm are installed in
place. Please read the pictures in the section "User's Maintenance Instructions" to know those
components.
To place the dishes in the dishwasher, much care shall be taken to avoid dosing failure of
top cover because the dishes support the top cover. The dishes placed in the dishwasher
must not be higher than the drawer, or be pressed forcefully for fear of damage.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical,sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
The cleaning and maintenance must not be performed by the unsupervised children.
The children are prohibited to play in the dishwasher, seat on the dishwasher, or play in
the abandoned dishwasher.
If the cleaning agent of dishwasher is used, it is suggested to add the dish washing
powder and apply one washing program immediately after cleaning in order to prevent
the washing agent from damaging the dishwasher.
The dishwasher is intended for ordinary household dishes, and must not be used to
clean the dishes polluted with gasoline, paint, rust, corrosive or acid or basic chemical.
If the dishwasher is not used in a long period, the power source and water faucet of
dishwasher shall be turned off.
The dishwasher must not be used to clean the plastic dishes except for those marked
with "Dishwasher allowed" or other equivalent sign. For the plastic dishes without such
sign, please refer to the manufacturer's suggestions.
Technical Data
Technical Data
Power source
Power Max. power : 1850W
Water consumption
Outline dimension
Weight (net)
Drying mode
220-240V～ ,50Hz
8.4L
595x569x595 (wide* deep* high) mm
About 30Kg
By blower
4 41
Page 11
Data of Washing Program
To know the selecting method of program, please refer to "Quick Guidance".
The time of washing program is given in the following table:
Auto
Prewashing
20min
Prewashing
18min
Main
O
C
Cold rinsing
5min
Cold rinsing
3min
Hot rinsing
55OC
Drying
stage
Heavy Daily
Main washing
58 OC
Main washing
55 OC
Cold rinsing
7min
Hot rinsing
65OC
Drying stage Drying stage Drying stage
Main washing
55 OC
Cold rinsing
7min
Cold rinsing
9min
Hot rinsing
65OC
Eco Short
Main washing
45 OC
Cold rinsing
7min
Cold rinsing
7min
Hot rinsing
50OC
Main washing
40 OC
Rinsing 7min
Hot rinsing
Drying stage
Glass
Main washing
45OC
Cold rinsing
8min
500C
Notice:
The washing time depends on many factors such as water temperature, ambient condition,
quantity of dishes, and if the drawer is opened during washing. The washing time shown on
the electronic screen is the approximate value calculated as per the water temperature 20 0 C.
Dish maintenance
Dish maintenance
When the dishwasher is used to clean the dishes, the mixture of high-temperature water
and dish washing powder may damage the dishes. Please keepin mind that if you have
any doubt about dish cleaning with dishwasher, please read the manual suppliedby the
product manufacturer,or washthedishes by hands.
Knives, forks and silver dishes
All the knives, forksandsilver dishes shall be cleanedimmediatelyafter use inorder to
prevent any food from drying on their surface; insuch case, the washing program is all
owed. The sliver dishes must not contact the stainless steel dishes; otherwise, stains ma
y appear on their surfaces. The sliver dishes must be taken out from the dishwasher and
wiped dry immediately after the washing programfinishes.
Aluminum dishes
The use of dish washing powder mayreducethe surface glossof aluminum dishes. The
gloss change degree depends on the product quality.
Other metal dishes
The iron and cast iron dishes may become rusty, and leave stains on other dishes.Similarly,
copper, tin-leadalloyand brass dishesmay have stains on their surfaces.
Wooden dishes
The wooden dishesare sensitiveto heat and water, and the frequent washing
with dishwasher may affect thequality of dishes adversely. In case of anydoubt about
this, please wash the wooden dishes by hands.
Glassware
Most of glassware can be cleaned with dishwasher. However,crystal, carved and
antique glassware may be etched, and become nottransparent. Therefore, you may
be prone to hand washing for such glassware.
Plastic dishes
Some plastic dishesmay be distorted or discolored in case of contact with hotwater.
Before cleaning the plasticdishes, the manufacturer's instructions shall be read. The
plastic dishes that can be cleaned with dishwasher shall be placed at thebottom of
dishwasher so that they will not be turned over,filled with water or fall in the course
of washing.
Ornaments
Most of modem chinaware can be cleaned with dishwasher. However, the chinaware
with patterns, golden edges and hand drawings are more sensitive to the washing of
dishwasher.In case of any doubt about this, please wash the them by hands.
Adhesive dishes
When the adhesive dishes are washed with dishwasher, some adhesives must be
softened or dissolved. In case of any doubt about this, please wash the them by hands.
40 5
Page 12
Packing List
Please check the accessories in the box according to the List
NO. Packing content
1
2 Basket components
3 Cutlery basket
4
5 Manual 1 set
6 Warranty Card 1 set
7
8 Mounting screws 1 set
Product size specifications
Machine
Water inlet pipe 1 set
Certificate of conformity 1 set
Quantity
1 set
1 set
1 set
Display
E01 Roof lifting motor failure
E02 The water inflow is abnormal, unstable or low.
E04
E05
E06 Overflow switch
E07
E08 Main board and sub board communication failure
E10
Possible failure cause
NTC test value is not symmetric (during Class B test)
The temperature rise of heater is abnormal (Class B heater
switch relay fails)
The temperature is over the upper limit
No temperature rise; the system cannot detect the
temperature rise after the heater starts.
Display board and motherboard communication failure
Any other failure that cannot be corrected automatically
6 39
Page 13
Fault Diagnosis
Press the key " " to eliminate the
beeping sound
If "E02" code is shown
Ensure that the water source is
connected and the water pressure
is table, press the power key to
eliminate the noise, and press the
key " " to continue washing
If "E06" code is shown
Overflow warning the system enters the
failure mode, and the water drain pump
starts.
The current program is cancelled,
and a failure warning is given. The
Machine cannot start any washing
program.the system can become normal
only after the on-line test program is applied
again and the test results are acceptable.
Start
Check and record the error code
according to the failure table
If "E01" code is shown
Roof lifting motor
failuer
Check or replace the
motor
If "E05" code is shown
Replace the electric control panel and
the motor heat pump,
Check if X3 wiring is connected
reversely or is in open circuit.
If "E04" code is
shown
The current program is
cancelled,
and a failure warning is
given. The
machine will be tested
again after
it restarts. If normal, the
machine
If "E l0" code is
shown
Part Name
Indicator icon
Display
Touch Button
Handle
Glass Panel
38 7
Page 14
Part Name
Failure
Possible cause
Solution
Electrical schematic diagram
Cylindrical filter
Flat filter
Microfilter
There is no water around
the motor.
loud
How to know the occurrence of failure?
With the auto diagnosis function, the dishwasher can warn
the user of the failure through the continuous beeping sound.
Both the washing program panel in the drawer and
the screen show the error code.
What measure shall be taken in case of failure?
Diagnose the failure in accordance with the flow chart below. Partial failures may be
eliminated (together with others); however, it is necessary to contact the after-sales
service center to arrange the repair. Please refer to the section "Troubleshooting" for
the contact information.
Such case often happens upon initial
use of dishwasher or reuse of
dishwasher that has been out of
service for a long period. 3 cups of
water shall be filled into the
dishwasher before the washing
program starts.
8 37
Page 15
Troubleshooting
time expires, or the drawer is opened.
Product Specifications
Failure
The drawer
cannot be
opened (no
beeping or
water sound)
Power failure in
the course of
washing
With continuous
beeping, the error
code is shown on
the screen
The machine makes
intermittent
beeping
The dishwasher
cannot start
The
dishwasher
makes noise
after washing.
The dishwasher
makes noise after
the dishwasher is
closed (before a
new washing
program starts).
Possible cause
The child lock function is
activated.
Drawer-close auto lock
option
Power failure in your
home or community
A failure occurs.
The dishwasher is paused. Turn on the dishwasher, and press
The power supply is not
turned on
The drawer is not closed
properly
The key lock or child lock
function is activated
No key is pressed Press the key '
This is normal. In the
drying program, the
noise will continue from
completion of washing to
end of drying.
This is normal. After
washing, the noise
caused by drying may
continue till the drawer
is closed and the set
time expires.
Solution
Disable the child lock. Press the
key” " till no symbol is
shown on the screen.
Press any key, and start the
dishwasher within 30s
After power restoration, continue the
dish washing from the step when the
washing program interrupts.
Refer to the section "Occurrence of
Failure"
the key " ” to continue the
dish washing.
Turn on the power supply
Ensure that the drawer is closed properly
Disable the key lock or child lock,
and press the key " " till no
symbol is shown on the screen, or
the indicator lamp goes out.
No need to pay attention. The noise
will stop automatically when the set
Sometimes, the noise may continue
after the drawer is closed.
No need to pay attention. The noise
will disappear when the set time
expires.
Product name Drawer dishwasher
Rated Voltage
Voltage Range
Rated Power
Rated Volume
Laundry guide
Drying method
Inlet water pressure O. 04-1. 0Mpa
Capacity
After—temperature drying
220-240V~
50Hz
1850W
87L
Spray type
7 sets
Display LED
Control
Installation BuiIt-in
Product Size (W*H*D) 595*595*569 mm
Touch control
Package (W*H*D) 660*660*660 mm
36 9
Page 16
Danger of cutting
sales service
Installation Precautions
Important safety instructions!
•Only qualified personnel mastering basic mechanical and electrical knowledge may install the
dishwasher.
•The instruction book must kept by the customer.
•The installation must be made as required by local building codes and electrical codes.
•At the end of dishwasher, the installation personnel must perform a final inspection.
•Remove all packaging materials of the dishwasher.
•The dishwasher is only for indoor use.
•Make sure all water pipe connectors are closed. The plumber must ensure that the installation comply
with all laws and regulations.
•When installing the dishwasher, consideration must be made that it is possible to take it out for
maintenance in future.
•The switching power supply socket must be outside the installation cabinet for dishwasher so as to facilitate simple
insertion and extraction after installation.
•Be careful when installing or taking out the dishwasher; do not damage the power line or water pipe.
•Incorrect installation of the dishwasher may make the warranty or claim right invalid.
•Where the dishwasher is installed in motor home, ship or similar mobile facility, the customer must at
his own cost drive the said mobile facility to the maintenance center or pay the travel cost incurred by
the maintenance technician for arriving at the installation site for maintenance.
Properly keep these instructions
Electric shock hazard
Before installing the dishwasher, take off household fuse or open the circuit breaker. The
dishwasher must be grounded. In event of fault or failure, the ground protection may provide
current with one discharge path of the minimum resistance, reducing the risk of electric shock.
The dishwasher is equipped with one conductor, which has equipment grounding wire and
grounding plug. The plug must be inserted into a proper socket which is installed and suitable
for grounding as per local laws and regulations. Warning - improper equipment grounding wire
may lead to electric shock. If you doubt whether the dishwasher is correctly grounded, please
contact senior electrician or service representative for check.
Never modify the power plug of dishwasher; in case the plug is not matched with socket, ask
senior electrician for installing proper socket. Never use extension cord, adapter or multi-pin
socket.
Otherwise, electric shock and even death may take place.
Be careful - the front edge of shell is very sharp.
It may cause personal injury or occasional cut when you are not careful
enough.
Warning!
Warning
Failure Possible cause Solution
Water
leaking
The drain pipe is not
correctly connected to
the drain hole.
Water supply and drain
pipes are not
connected correctly.
Other water leaking
Reinstall the drain pipe onto the drain hole.
Ensure that the water supply and drain
pipes are connected securely.
Turn off the power source and water faucet of
dishwasher, and contact the afterdepartment of Haier for repair. Refer to the
section "Cleaning and Maintenance" for more
information.
10 35
Page 17
wash the dishes.
Refer to the examples of correct and wrong adding
Refer to the section "Adding of Washing Agent', or
Troubleshooting
Failure Possible cause Solution
Fail to wash
clean
The washing program and the
dish capacity are not suitable.
The spray arm does not rotate.
The drawer is filled too fully or
the dishes are not arranged
properly.
The strainer/ installation of
strainer is wrong.
The washing agent is added
into the wrong feeder.
The dishes are placed in the
dishwasher before the food
residues and oil stains on the
dishes are removed
The washing agent is inapplicable.
Refer to the "Quick Guidance" and select the
suitable program; or, the dirt is dry and affixed
onto the dishes so the dishes have to be
soaked for a period.
Ensure that the rotation of spray arm is not
obstructed by other object.
Refer to the section about dish arrangement.
Refer to the section "Cleaning and Maintenance".
The washing agent must be added into the large
feeder box. Refer to the section "Adding of
Washing Agent'.
Remove the food residues and oil stains on the
dishes before the dishes are placed in the
dishwasher.
Add the correct washing agent to
of washing agent given in the section "Adding of
Washing Agent'.
Product Installation Guidelines
670mm (Standard floor cabinet)
55mm (Cabinet plate)
The washing agent is insufficient.
The spray arm is clogged. Clean the spray arm.
The strainer or filter is clogged Clean the strainer and filter.
There are
bubbles
34 11
The dosage of washing agent is
wrong.
There is too much egg white
on the dishes.
The rinse aid setting is too high. Decrease the dosage setting of rinse aid.
The rinse aid feeder box is not
closed tightly.
observe the suggestions of washing agent
manufacturer.
Refer to the section "Introduction to Program", or
observe the suggestions of washing agent
manufacturer.
Increase the dosage of washing agent.
Ensure that the rinse aid feeder is closed tightly,
and refer to the section "Adding of Rinse Aid".
Page 18
Installation Guide lines
Water inlet connection to dishwasher:
Connection method of drain pipe:
The outlet end of the drain pipe can be inserted into the upright sewer,Or connect to the turning
joint of the sink sink. The drainage pipe must be fastened with a clamp and the screws must be
tightened.
When connecting the drain pipe, pay attention that the highest part of the drain pipe cannot
exceed the highest height of the dishwasher.
In order to prevent the backflow of sewage, the outlet of the drainage pipe cannot be immersed
in water, and the drainage pipe is not bent and concaved.
It is best to install the dishwasher near the drain pipe. The length of the dishwasher drain pipe is
about 1.5 meters. If it is far away, users need to purchase adapters and drain pipes by themselves,
but the total length should not exceed 4 meters, otherwise it will affect washing.
Cleaning of spray arm
1. Power off the dishwasher, or unplug the power wire plug.
2. Lift up the glass cup bracket from the bracket iron wires (if the bracket is folded), lift up all the
tea cup trays, and ensure that they are vertical and close to the drawer top.
3. Remove the dish rack carefully: lift up the rear part of lower rack, and during this course,
notice to prevent the front end of rack from colliding with the feeder box or rinse aid box.
4. Take out the spray arm, and remove all the residues in the spray arm.
Wash the spray arm With clean water, and then wipe it dry with wet cloth.
5. Insert the spray arm onto the support.
6. Properly install the lower dish rack, and notice to first install the front end of lower dish rack
in place.
7. Push in the drawer, and power on the dishwasher.
Notice: The broken glass or tea cup debris in the drawer must be removed completely and
carefully for fear of damaging the dishwasher
Spray
The drain nozzle must not be immersed in water.
12 33
Page 19
Removal and cleaning of strainer and filter
3. Lift up and remove the filter. It is normal if there is water under the filter.
4. As shown on the picture, rotate the filter cap and handle, and lift up the filter
cap at the filter cap notch to separate the cap from the handle.
Notice: Never try to separate the filter cap from the handler from both
sides at the same moment; otherwise, the filter may be damaged.
5. First rinse the strainer with hot soapy water, and then wash it with clean water.
6. Take out the handle carefully. Remove all the dirt from one side,
rinse the handle with soap water, then wash it with clean water, and
next wipe it clean with wet cloth.
7. Arrange the filter cap carefully in place, and ensure that the
filter cap is clamped at the fixed position.
8. Re-fasten the filter:
A. Combine the filter cap with the handle.
B. Rotate the filter cap till the lifting cup on the handle is
aligned with the fine filter mesh, and next rotate it clockwise to
clamp them tightly.
C. Rotate the lifting cup till the lifting cup slot and water tank
buckle are fastened.
D. Rotate the filter till the clamping sound of slot is heard and the
filter cannot be rotated anymore; now, the installation of filter
completes.
Rotate the lifting cup till the lifting cup
slot and water tank buckle are fastened
Installation steps
of strainer:
1.place the fine filter
in the water tank.
9. No matter whether the whole lower dish rack (which has
been removed) or the moveable bracket is installed, ensure
that they are refitted correctly. (As described above, the moveable
bracket shall be clamped onto the fixing buckle of lower rack).
10. Install the bracket door.
Place the bracket door on the lower dish rack,
and then install the knife barrel.
Installation Guidelines
Notes on water and electricity connection of dishwasher:
I. The water inlet and drain pipes can be placed on the left or right side according to the installation needs.
2. Choose a place near the water inlet or drain line, and also near a power source with a reliable ground.
3.Connection diagram on the right.
32 13
Page 20
Installation Guidelines
Pass the water pipe through the cabinet shelf.
Cleaning of strainer and filter
Important note!
If the cleaning or anti-scaling agent of dishwasher is used, one washing program shall be
applied after washing to prevent the cleaning agent from damaging the dishwasher.
When the dishwasher is used, the strainer, filter and spray arm must be installed in
place.
To use the dishwasher, it is suggested to fasten the rack at the correct position by the
right hand.
Removal and cleaning of flat filter and fine filter
1. Push in the foldable rack on the dish barrel, and then lift it up so that the flat filter and other
components under the foldable rack can be removed for cleaning without taking out the whole
barrel (counterclockwise rotate the lifting cup, and when the flat filter becomes loose, take out
the flat filter), facilitating the operation.
2. After cleaning, refit the filtration system: first place the fine filter in the water cup, then install
the flat filter, and next refit the lifting cup and clockwise screw down the lifting cup; at last, refit
the foldable rack on the dish barrel.
Rotate leftward or rightward
14 31
Page 21
Cleaning and Maintenance
Important note!
The dishwasher must be powered off during cleaning and maintenance (unplug the
power wire of dishwasher, or turn on the fuse).
Holiday maintenance
If the dishwasher is not used in a long period, you are suggested to clean and unload
the dishwasher, open the drawer to circulate the air inside, and turn off the power
source and water faucet of dishwasher.
Before the dishwasher that has been out of service for a long period is reused, it is
suggested to add 3 cups of water into the dishwasher, in order to moisturize the parts
that become dry due to long-period no use.
Cleaning of dishwasher surface
1. Wipe the dishwasher surface of clean wet cloth, and notice not to wet the control panel.
2.Wipe the surface dry with clean lint-free cloth.
Important note!
You are suggested no to wash the dishwasher by the following methods
because they may damage the dishwasher:
Plastic or stainless steel wiping pad;
Abrasive agent, organic solvent or household cleaning agent;
Acid or basic cleaning agent;
Liquid soap or soap;
Stainless steel cleaning or polishing agent;
Laundry soap powder or sanitizer.
Cleaning of strainer, spray arm and filter
In case of normal use, it is suggested to clean the strainer and filter at least once every
month or when the food residues are found on the strainer or filter.
In case of normal use, the spray arm does not need frequent washing.
Fixing of the dishwasher.
Put the dishwasher into the pre-opened cabinet smoothly. After
putting it in place, pull out the drawer, and then fix the screw holes
reserved on the sides of the dishwasher with the screws provided
Check the dishwasher after installation:
1 .Whether the dishwasher is installed smoothly;
2.Whether the joints of the water inlet pipe and the drain pipe of the dishwasher
are properly connected and whether there is water leakage;
3.Whether the power plug is inserted properly;
4.Whether the water inlet faucet is turned on;
5.Pull out the drawer and remove all the accessories from the dishwasher;
6.Power on the dishwasher and run the standard wash program for 2-5 minutes.
Turn off the machine after confirming that there are no abnormalities
Installation Guidelines
Screw fixing holes.
30 15
Page 22
Instructions
Start
If it is the very first initialization for the dishwasher, then the Choose Program screen is shown:“HELLO”
I .Dark after Welcome-letters ,
2 .After Welcome-letters passing: CHOOSE p (Choose Program);
3.Continuous Welcome-letters.
After pushing " "(program) button, program selection is started.
For the next starts, the last program used, should be pre-selected, so that display shows the last run
program and can be started immediately by pushing "Start/Pause".
By Pushing " " (Program button), you can choose the
washing program/ profile. The Washing profile name is shown
in the display and is shown in a short form:
Press the start/pause “ ”button for 3-5seconds to cancel the
current program.
Alternating to the program name (short form) at display the
related program time segments are displayed. This alternating/
switching between program name and related program time (e.g. every
2seconds) ends by pushing "Start/Pause" to start the program. From
there on only the program time is displayed and counted down based on
the profile definition.
Operating Mode
After the program is started, only the program time is displayed and starts to count down as long as the
program is in progress. Time values are display steadily, the dots in between are displayed with flash.
By pushing the Start/Pause button during the program is running, the program is paused.
At display the related program time is displayed flashing. The dots in between are displayed steadily. When the "
"button is pushed again, program continues. Remaining time display continues counting down.
Add the rinse aid
How to add the rinse aid
Note:lf there is no distributor model, cannot add the rinse,
Combination of washing the dishes is recommended to be used.
1. Counterclockwise rotate and remove the plug.
2. 2.Add the rinse aid into the round hole. Notice to prevent the rinse
3. Aid from splashing outward the feeder.
Important note!
The spilled rinse aid, if any, must be wiped off; otherwise,
Much bubbles may be produced, resulting in damage
to dishwasher and loss of warranty.
3.Refit the plug, and then clockwise rotate the plug in place.
Important note!
Ensure that the plug is tightened, and the plug handle is vertical.
Dosage of rinse aid
The dosage of rinse aid for every washing process shall be
adjusted between "0" (min.) and "5" (max.) according to the
local water hardness. Please refer to the section "Preferred
Options" in "Quick Guidance" for details.
If there are many bubbles after washing, the dosage
setting of rinse aid shall be decreased.
If the dish drying effect is not good, the dosage setting
of rinse aid shall be increased.
If you live in the hard-water region where no water softener
is installed in the water supply pipeline, it is suggested to adjust
the dosage setting of rinse aid to "5".
Rotate and tighten the plug
Add the rinse aid into the feeder
16 29
Page 23
Use instructions of washing block
If the washing block is used, the manufacturer's suggestions on the packing bag shall be
observed. Some washing blocks may not be applicable to all the washing programs.
The use of washing block in the region with hard water can improve the washing effect.
Ensure that the washing block does not contact the dishes, knives or forks directly.
If the used washing block contains any rinse aid, you are suggested to lower or disable
the function of rinse aid. Please read the introductions in "Quick Guidance" for details.
Important note!
Washing agents of dishwasher are strongly basic. The unexpected swallowing of washing
agent may be very hazardous. Skins and eyes shall be protected from washing agent.
When the dishwasher is opened, the children and the weaker people must be far away
from the dishwasher. After washing, it is required to check if the washing agent feeder
box is drained completely.
In order to improve the drying effect of dishes, the use of rinse aid is suggested.
The rinse aid can remove the water stains on the glassware and chinaware, and prevent
the metallic products from loss of gloss.
The rinse aid feeder is located inside the drawer and under the washing agent feeder.
About 50mI rinse aid can be added into the rinse aid feeder.
It is normal to hear the abnormal sound when the rinse aid feeder is operating.
When to add the rinse aid
If the lack of rinse aid is detected, the above sign will be shown after the machine starts.
The sign will flash for three times every minute, to warn the user of adding the rinse aid.
If the rinse aid indicator lamp does not go on, it is unnecessary to add the rinse aid, and
the existing rinse aid is enough for the washing program.
Notice: Compared with the rinse aid with darker color, the dimming level of indicator lamp is
less if the rinse aid with lighter color is used.
Touch Instructions
Lid motor operation
1. When press the "stop/start" button to boot, the top motor will drive the top drawer downward
seal, and then the program will start.
2. The program is running mode, press the "stop/start" button to suspend the program runs.Within
the prescribed period of time, the top motor drivel-Jpward, completely release the machine head, a
buzzer two sounds to inform lid seal has been released.
3. After the start the program or in the process of the program is running, not to pull out the drawer,
have to press the "stop/start" button,
Such as roof upward in place after the buzzer two to pull out the drawer.
Time Delay
is ente
Progra
red.
m S
election mode.
It is possible to activate a time delay for the washing program to start.
The time delay can be activated by pushing ( ) + ( ) keys for 3 seconds during
Program Selection mode.
During Time Delay Selection mode, time delay changes in I hour steps (counting up)
by pressing ( ). The time delay at a maximum can be 9 hours: "+ 9".
The complete sequence while pressing ( ) is:
By pushing ( )with”OFF”seleection,the time delay is cancelled and program
Selection mode.is set back.
By pushing ( ) with any other selection, the time delay is set and Time delay starts counting
down every minute.
During Time Delay Counting mode, after the time delay is exhausted the washing
program is started in the standard operation way (see Program running mode).
Note: Once Time Delay mode is set, the door must be sealed through the Lid motors.
So,
If the user needs to access the basket, this mode must be cancelled first.
Settings
• Settings can be configured by using a button combination during Start or Program Selection mode.
y
p
ushin)gs( )
IBf
(
••
B
y
i
press
i
pressed
ng
+it(
wsith
w
)
(
fbo
r
2
se
c
o
d
sio)n,nt
e
s
trisn
gs
menu
"
a
c
s
e
lwenc
t
,
it
e
ttu
n
s
back to
it
c
h
e
sk"b
e
t
e
e
she
trt
ien
g
.
28 17
Page 24
• By pressing ( ) while any setting is selected, the corresponding setting submenu is entered in
order to change the preferences.
The following table shows visualization for each setting:
Settings
By pushing ( ) the level or preference changes (switching) starting from Water
Softener and finishing in Back. The following table shows the different submenu
selections for each setting:
Childlock function
There are two ways of managing Childlock:
1、Childlock can be automatically activated for every start after selecting a program and pressing
( ) if "Permanent activation of Childlock at start' is configured as "ON" as a preference in
settings menu.
2、Otherwise, to activate childlock mode: press ( ) for 3 seconds during Program Running mode.
If the activation is successful, the 7-segment shows:
While Childlock is activated all other touch area functions are disabled and remains ON.
By touching any button, the Childlock activated screen is shown for 2 sec (see above table).
To unlock / deactivate Childlock, ( ) has to be pressed again for 3 seconds. When
deactivation was successful, the indicator symbol is not lighted any more and all other
Inapplicable washing agent
The following washing agents are inapplicable to the dishwasher, and may damage
the dishwasher and result in loss of warranty.
Important note!
The following washing agents must not be used in the dishwasher:
Washing fluid
Laundry soap powder
Liquid soap
Soap
Sanitizer
Dosage of washing agent
For the dish washing powder, please refer to the last section "Introduction to Washing
Program", and add the dish washing powder according to the local water hardness.
A suitable amount of washing agent shall be filled according to the adding mark. Other
washing agents shall be added according to the manufacturer's suggestions.
full (40. 5g)
1/3 (27g)
1/3 (13. 5g)
18 27
Page 25
Adding of washing block
Notice: You can see the washing agent with similar washing effect sold in the supermarket,
know and observe the use suggestions of washing agent manufacturer.
Add the washing block into the washing block
Box on the knife and fork barrel
touch areas are enabled again.
Knife and fork barrel
In order to reduce the risk of injury, your are suggested to place the sharp edges of
knives, forks and other sharp dishes downward.
If the spoons are mixed with knives and forks, the contact faces may not be rinsed
with water so you are suggested to place the spoons and the knives and forks
separately, to ensure the complete water rinsing (of dishes).
The stainless steel dishes must not be placed together with sliver dishes, in order to
avoid stains on the sliver dishes.
If the knife and fork barrel is not used during washing, the washing block can be placed
directly at the drawer bottom (around the fine filter, at the lower position on the bottom).
Knife and fork barrel cover and cleaning
If there are dirty things in the basket or large pieces of dirt must clean up, can open
the basket to clean.
26 19
Page 26
Basket
Tableware layout (reference) :
Cup bracket placement diagram (reference) :
Type Item
a Dinner plate
b Souper plate
C Dessert plate
d Saucer
e Glass
I Soup spoons
2 Knives
3 Knife
4 Dessert spoons
5 Tea spoons
Adding of Washing Agent
Adding of dish washing powder
Notice: You can see the washing agent With similar washing effect sold in the supermarket,
know and observe the use suggestions of washing agent manufacturer.
Pour the dish washing
powder into the washing
agent chamber
Washing agent chamber
Pour the dish washing powder into the washing agent feeder
1.Press the buckle to open the washing agent feeder.
2.First check if the washing agent feeder box is empty and dry, and then pour in the dish
washing powder (never add the blocky washing agent into the washing agent feeder). The
Rinse program does not need any washing agent.
3.Close the feeder till the buckle is fastened. The dish washing powder may fall into the
bottom of dishwasher drawer.
Notice: When the dishes to be cleaned are very dirty and the used water has a high
hardness, a suitable amount of washing agent shall be added to improve the washing
effect.
Note:
If no dispenser model configuration, then put the detergent directly into the
dishwasher;
If the block is put in the dishwasher, take the blocks on the knife and fork
basket gap position.
20 25
Page 27
Washing procedure is introduced
First know the hardness of your water, and then determine the necessary dosage of washing
agent according to the following form. Meanwhile, please refer to the section 'Water Softener'.
Please read "Quick Guidance" to know the program to be selected.
The dosage of washing agent has been marked on the washing agent feeder. Please
refer to the section "Adding of Washing Agent".
Water hardness Dosage of washing agent
Percent concentration (ppm)
Dosage marking on Dosage
British concentration (gpg) Washing program washing agent feeder
Heavy 2/3 27g
< 100ppm
Daily 2/3 27g
Eco
Short
Glass
1/3 13.5g
-
1/3
-
13.5g
Cup holder
2/3
Auto
If the water softener is installed in your home, please refer to the suggested dosage
*
for the water with hardness below 100ppm (regardless of local water hardness).
Notice:
If the hardness of your water is above 625ppm, the washing effect of dishwasher may
be reduced.
24 21
27g
Page 28
Place the dishes in the drawer
Place the dishes in the drawer. Please make sure that:
• The arrangement of dishes must ensure that the water sprayed by spray arm can reach
any zone where the dishes are placed (the improper arrangement of dishes may result in
bad washing effect).
• No dish shall obstruct the water sprayed by spray arm from reaching the dishes placed on the
foldable cup tray.
• Keep the glassware and other fragile dishes stable to prevent the glassware from being destroyed
by the water flow sprayed by spray arm.
• Examples of wrong dish arrangement
Water hardness is introduced
What's the water hardness?
The hard water indicates the water with a high content of calcium, magnesium and
other minerals. The content of such minerals in the soft water is lower. The water in the different
region has a different hardness.
What impact does the hard water have on the washing effect?
The hard water has adverse impacts on the washing effect. The long-period use of hard water
may reduce the transparency of glassware, and form the white scale on the surface of bowl. The
long-period use of high-hardness water may damage the internal components of dishwasher.
If the dosage of washing agent is suitable, the natural soft water and artificially softened water
have no adverse impact on the washing effect. If the excessive amount of washing agent is used
in the hot water, the glassware may be etched permanently. The etching starts in the form of
rainbow film; if the etching continues, the glassware may become non-transparent for ever.
How is the impact of adverse factor reduced?
Please contact the local water supply company to know the hardness of your tap water.
If your water is the hard water, and your dishwasher is not equipped with internal
water softener...
Please follow the suggestions about dosage of washing agent given on the last pages.
If possible, the washing agent with a high content of phosphate can used because the
phosphate can soften the water and thus improve the washing effect. If it is impossible to use the
washing agent with a high content of phosphate, the multi-function washing block is suggested.
Use of rinse aid: It is suggested to adjust the dosage of rinse aid to "5" in order to improve the
washing effect.
The dishwasher shall be washed regularly with cleaning or anti-scaling agent. The
dishwasher in which the scale is found shall be washed immediately with cleaning or
anti-scaling agent.
Important note!
You are suggested to add the water softener in your water supply pipeline. If the hardness of
your water is above 250ppm, the water softener must be installed to ensure the acceptable
washing effect.
If your water is the natural soft water or softened water•••
The dosage of washing agent shall not be too much. The suggestions about dosage of
washing agent given on the last pages shall be followed.
Ensure that the drawer is not filled too fully so that all the dishes can be washed with water.
22 23
Page 29
Worldwide Appliances Pty Limited
A.B.N. 45868077422
Oce:
48-50 Moore Street, Leichhardt N.S.W 2040
Post:
Locked Bag 3000, Annandale, N.S.W 2038
P: 1300 694 583
WARRANTY REGISTRATION
Your ongoing satisfaction with your artusi
product is important to us. We ask that you
complete the enclosed Warranty Registration
Card and return it to us so that we have a record
of the artusi product purchased by you.
PRIVACY
Worldwide Appliances respects your
privacy and is committed to handling your
personal information in accordance with the
National Privacy Principles and the Privacy
Act 1988 (Cth). A copy of the Worldwide
Appliances Privacy Policy is available at
www.artusi.com.au. Worldwide Appliances will
not disclose any personal information set out
in the Warranty Registration Card (“Personal
Information”) without your consent unless
required by:
1. law;
2. any Worldwide Appliances related company;
3. any service provider which provide services
to artusi or assist artusi in providing services
(including repair and warranty services) to
customers. Our purpose in collecting the
Personal Information is
to keep a record of the artusi product purchased
by you, in order to provide a better warranty
service to you in the unlikely event that there is
a problem with your artusi product. Worldwide
Appliances may contact you at any one or more
of the address, email address or telephone
numbers set out in the Warranty Registration
Card. Please contact artusi on 1300 694
583 should you not wish to be contacted by
Worldwide Appliances.
WARRANTY
1. Warranty
Worldwide Appliances warrants that each artusi
product will remain, for a period of either 12
months or 24 months of warranty. All Warranties
are valid from the original date of purchase, And
warranty claims must be accompanied by the
proof of purchase.
24 months warranty products:
All Built-in Appliances – Limited to Ovens,
Gas, Induction and Electric Cooktops, and All
Rangehoods
Freestanding Cookers - Gas and Electric Models
(900mm Width)
Dishwashers - Freestanding, Fully Integrated,
Semi Integrated and built-in
12 months warranty products:
Freestanding Cookers - Gas and Electric Models
in 50cm, 54cm and 60cm Widths
Portable Appliances* – Benchtop Models and
Portable Gas Models
2. What is not Covered by the Warranty.
The Warranty does not apply if an artusi product
is defective by a factor other than a defect
arising in the manufacture of the artusi product,
including but not limited to:
(a) damage through misuse (including failure
to maintain, service or use with proper care),
neglect, accident or ordinary wear and tear
(including deterioration of parts and accessories
and glass breakage);
(b) use for purpose for which the artusi product
was not sold or designed;
(c) use or installation which is not in accordance
with any specied instructions for use or
installation;
(d) use or operation after a defect has occurred
or been discovered;
(e) damage through freight, transportation or
handling in transit (other than when Worldwide
Appliances is responsible);
(f) damage through exposure to chemicals,
dusts, residues, excessive voltage, heat,
atmospheric conditions or other forces or
environmental factors outside the control or
Worldwide Appliances;
(g) repair, modication or tampering by the
purchaser or any person other than Worldwide
Appliances, an employee of Worldwide
Appliances or an authorised artusi service
contractor*;
(h) use of parts, components or accessories
which have not been supplied or specically
approved by artusi.
(i) damage to surface coatings caused by
cleaning or maintenance using products not
recommended in the artusi product handbook
provided to the purchaser upon purchase of the
artusi product;
(j) damage to the base of an electric oven due
to items having been placed on the base of
the oven cavity or covering the base, such as
aluminium foil (this impedes the transfer of heat
from the element to the oven cavity and can
result in irreparable damage); or
(k) damages, dents or other cosmetic
imperfections not aecting the performance
of the artusi in respect of an artusi product
purchased as a “factory second” or from display
The Warranty does not extend to light globes
used in artusi products.
3. Domestic Use
Each artusi product is made for domestic use.
This Warranty may not extend to artusi products
used for commercial purposes.
4. Time for Claim under the Warranty
You must make any claim under this Warranty
within twenty eight (28) days after the occurrence
of an event which gives rise to a claim pursuant
to the Warranty, by booking a service call on the
telephone number below.
Continued over...
Page 30
5. Proof of Purchase
Customers must retain proof of purchase in order
to be eligible to make a warranty claim in respect
of an artusi product.
6. Claiming under the Warranty
Customers will bear the cost of claiming under
this Warranty unless Worldwide Appliances
determines the expenses are reasonable, in which
case the customer must claim those expenses
by providing written evidence of each expense
to Worldwide Appliances at the address on the
Warranty Registration Card.
7. Statutory Rights
(a) These terms and conditions do not aect your
statutory rights.
(b) The limitations on the Warranty set out in this
document do not exclude or limit the application
of the consumer guarantees set out in the Act or
any other equivalent or corresponding legislation
in the relevant jurisdiction where to do so would:
(i) contravene the law of the relevant jurisdiction;
or
(ii) cause any part of the Warranty to be void.
(c) Worldwide Appliances excludes indirect or
consequential loss of any kind (including, without
limitation, loss of use of the artusi product) and
(other than expressly provided for in these terms
and conditions) subject to all terms,
conditions and warranties implied by custom,
the general law, the Act or other statute.
(d) The liability of Worldwide Appliances to you
for a breach of any express or non-excludable
implied term, condition or warranty is limited at
the option of Worldwide Appliances to:
(i) replacing or repairing the defective part of the
artusi product;
(ii) paying the cost of replacing or repairing the
defective part of the artusi product;
(iii) replacing the artusi product; or
(iv) paying the cost of replacing the artusi
product.
(e) Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund
for a major failure and for compensation for any
other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
8. Defects
Any part of an artusi product deemed to be
defective and replaced by Worldwide Appliances
is the property of Worldwide Appliances.
Worldwide Appliances reserves the right to
inspect and test artusi products in order to
determine the extent of any defect and the
validity of a claim under the Warranty.
*To locate your closest artusi authorised service
agent please contact us on 1300 652 100 or visit
www.artusi.com.au
ALL SERVICE CALLS MUST BE BOOKED THROUGH AN
AUTHORISED DEALER OR WARRANTY DEPARTMENT
ON 1300 652 100 OR stokesaps.com.au/artusiservice
01032014
Warranty Card tear off
WARRANTY REGISTRATION CARD
01052013
Last Name: First Name:
Address:
State: Postcode: Email:
Home Phone: Mobile:
Purchase Date: / / (Please attach proof of purchase to validate warranty)
MODEL NUMBER
1
2
3
4
Please complete and send to ARTUSI at: REPLY PAID 83617
LEICHHARDT NSW 2040
SERIAL NUMBER
(if you cannot locate the serial number please call ARTUSI on 1300 694 583)
01032014
Page 31
Page 32
DISCLAIMER
Worldwide Appliances PTY LTD, trading as ARTUSI, is continually seeking ways to improve the design specifications, aesthetics and production techniques of its products. As a result alterations to our products and
designs take place continually. Whilst every effort is made to produce information and literature that is up to date, this brochure should not be regarded as an infallible guide to the current specifications, nor does it
constitute an offer for the sale of any particular product. Product dimensions indicated in our literature is indicative only. Actual product only should be used to define dimension cutouts. Distributors, and retailers
are not agents of ARTUSI and are not authorised to bind ARTUSI by any express or implied undertaking or representation.
ARTUSI OFFICES ARE OPEN DAILY FROM 9AM–5PM AND SATURDAYS 10AM–4PM
NSW & ACT (HEAD OFFICE)
48-50 MOORE STREET
LEICHHARDT
F 02 8569 4699
VIC, TAS & SA
1211 TOORAK ROAD
CAMBERWELL
F 03 9809 2155
QLD
1/42 CAVENDISH ROAD
COORPAROO
F 07 3397 0850
WA & NT
UNIT 10/55 HOWE STREET
OSBORNE PARK
F 08 9201 9188
NZ
PO BOX 11.160
SOCKBURN CHRISTCHURCH
F 03 344 5906
ARTUSI.COM.AUP: 13 00 6 49 5 83
Loading...