Arrow HM108-A, VN108-A, SA108-A, MN108-A, EN108-A User Manual

Owner's Manual & Assembly Instructions

A01

Model No.EN108-A HM108-A MN108-A

NP108 NW108-A PD108-A
SA108-A VN108-A

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

709291207

BUILDING DIMENSIONS

Exterior Dimensions Interior Dimensions Door
*Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wall to Wall) Opening
Size Size Sq. Ft. Cu. Ft. Width Depth Height Width Depth Height Width Height

10' x 8' 121" x 92 3/4" 74 401 123 1/4" 95 1/4" 70 7/8" 118 1/4" 90" 69 5/8" 55 1/2" 58"

3,0m x 2,3m 307cm x 236cm 6,9m2 11,4m3 313cm 242cm 180cm 300cm 229cm 177cm 141cm 147cm

* Size rounded off to the nearest foot

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

BEFORE YOU BEGIN....

A2

Owner's Manual

Before beginning construction, check local building codes regarding footings, location
and other requirements. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.

Assembly Instructions: Instructions are supplied in this manual and contain all

appropriate information for your building model. Review all instructions before you begin,
and during assembly, follow the step sequence carefully for correct results.

Foundation and Anchoring: Your storage building must be anchored to prevent wind

damage. A foundation is also necessary as a base in order to construct a square and level
building. Anchoring and foundation materials are not included with your building. We
recommend the combined use of an Arrow Floor Frame Kit and an Arrow Anchoring
Kit as an effective method of securing your building to the ground (Available by mail order
or at your local dealer) or you may construct a foundation and anchoring system of your
choice. Your assembly instructions provide information on a few methods commonly used
to secure and level a storage building.

Parts and Parts List: Check to be sure that you have all the necessary parts for your

building.

•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the
numbers on the parts list. The parts list is located on page 12.

•If you find that a part is missing, include the model number of your building and contact:

Arrow Group Industries, Inc. Customer Service Department
Route 50 East Breese, Illinois 62230
1-800-851-1085

•Separate contents of the carton by the part number while reviewing parts list. The first few steps
show how to join related parts to make larger sub assemblies which will be used later.

•Familiarize yourself with the hardware and fasteners for easier use during construction. These are
packaged within the carton. Note that extra fasteners have been supplied for your convenience.

2

PLAN AHEAD....

A3

Watch the Weather: Be sure the day you select to install your building is dry and calm.

Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground.

Teamwork: Whenever possible, two or more people should work together to assemble

your building. One person can position parts or panels while the other is able to handle the
fasteners and the tools.

Tools and Materials: These are some basic tools and materials you will need for the

construction of your building. Decide which method of anchoring and the type of foundation
you wish to use in order to form a complete list of the materials you will need.

Required

• Eye Goggles

• No. 2 Phillips Screwdriver

(With Hardened Magnetic Tip)
Note: A power screwdriver or vari­able speed drill with Phillips-tip at­tachment can speed assembly by
as much as 40%.

• Work Gloves

• Step Ladder

• Utility Knife / Scissors

• Pliers

• Carpenter's Level

• Tape Measure

Required

Optional Time-Savers

• Wrench / Nut Driver

• Electric / Cordless Drill

• Square

• String (for squaring frame)

Foundation Preparation

• Hammer and Nails

• Spade or Shovel

• Hand Saw / Power Saw

• Lumber and/or Concrete

Selecting and Preparing Your Site: Before assembly, you will want to decide on

a location for your building. The best location is a level area with good drainage.

•Allow enough working space for ease of moving parts into position during assembly. Be sure there
will be enough space at entrance for doors to open fully and enough space around the building to
be able to fasten the panel screws from the outside.

•Before you begin the first steps in assembling your parts, a foundation should be constructed and
an anchoring system should be ready to use.

3

SAFETY FIRST....

A4

Safety precautions are important to follow throughout the construction of your building.

•Care must be taken when handling various
pieces of your building since some contain
sharp edges. Please wear work gloves, eye
protection and long sleeves when assembling
or performing any maintenance on your build­ing.

safety edge

sharp edge

sharp edge

safety edge

•Keep children and pets away from worksite to
avoid distractions and any accidents which
may occur.

•Practice caution with the tools being used in the
assembly of this building. Be familiar with the
operation of all power tools.

•Do not attempt to assemble the building if parts
are missing because any building left partially
assembled may be seriously damaged by light
winds. Call 1-800-851-1085

•Never concentrate your total weight on the
roof of the building. When using a step ladder
make sure that it is fully open and on even
ground before climbing on it.

4

•Do not attempt to assemble the building on a
windy day, because the large panels acting as a
"sail", can be whipped about by the wind making
construction difficult and unsafe.

CARE & MAINTENANCE....

A5 Web

Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-

up scratches as soon as you notice them on your unit. Immediately clean the area with
a wire brush; wash it and apply touch-up paint per manufacturer's recommendation.

Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy

amounts of snow on roof can damage building making it unsafe to enter. In snow country,
Roof Strengthening Kits are available for most Arrow Buildings for added protection
against heavy snow accumulation.

Doors: Always keep the door tracks clear of dirt and other debris that prevent them from

sliding easily. Lubricate door track annually with furniture polish or silicone spray. Keep
doors closed and locked to prevent wind damage.

Fasteners: Use all washers supplied to protect against weather infiltration and to protect

the metal from being scratched by screws. Regularly check your building for loose screws,
bolts, nuts, etc. and retighten them as necessary.

Moisture: A plastic sheet (vapor barrier) placed under the entire floor area with good

ventilation will reduce condensation.

Other Tips....

• Wash off inked part numbers on coated panels with soap and water.

• Silicone caulking may be used for watertight seals throughout the building.

Do not store swimming pool chemicals in your building. Combustibles and
corrosives must be stored in air tight approved containers.

Keep this Owner's Manual and Assembly Instructions for future reference.

5

A6 WEB

ACCESSORIES....

ROOF STRENGTHENING
(heavy snow load) KITS

Extra roof beams and gable braces
designed for added protection against
heavy snow accumulation. Increases
the strength of your roof by 50%.

ANCHOR KITS

Model No. AK4

Anchor Kit contains heavy-duty steel
augers, 60' (18m) of steel cable and 4 cable
clamps. No digging or concrete
pouring, just insert cable under roof,
over roof beams, into augers and twist
augers into the ground. For buildings
larger than 10'x9', use 2 kits.

Model No. AK100

New concrete anchor system permits
anchoring any size Arrow building
directly to a concrete slab. Each kit
contains heavy-duty, hot-dipped
galvanized steel corner gussets and
perimeter clips which fit over the floor
frame and lag bolt into a concrete slab.
Full assembly instructions and a 1/4"
masonary drill bit are included.

Model No. AK600

Earth Anchor Kit anchors any size
Arrow building to the ground.
Each kit contains heavy duty,
hot-dipped galvanized steel
corner gussets and 4 earth anchors.

FLOOR FRAME KITS

MODELS FB47410, FB5465, FB106-A

FB109-A and FB1014-A

A simple new floor frame system made of heavy-duty, hot-dipped
galvanized steel. Use as foundation for plywood, sand or stone.

ATTIC KIT / WORKBENCH KIT

Heavy-duty galvanized steel bars that
fit all 10' wide Arrow buildings. They
install quickly and easily to help
organize space and create more
useable space as an attic or
workbench. Will hold up to 250 lbs.
(113kg) evenly distributed.

Model No. Fits Shipping Weight

AT101

Must be drilled for use as workbench in Estator.
+ Even weight distribution.

10' Long, 250 lb. (113kg) load+

Fits all Arrow 10' wide buildings.

16 lbs. (7kg)

SHELF UNITS

Heavy-duty, galvanized steel shelf units help organize storage
space. They easily mount on the wall or sit on the floor. Fits all
Arrow buildings.*

TOOL HANGING RACK

Model No. TH100

The perfect tool organizer. Twin
25 1/2" (65cm) steel channels
plus five heavy-duty snap-in
hangers and a small tool holder for
screwdrivers, pliers, etc. Holders
slide along channel for fully
adjustable spacing. Great for
garage, basement, or the back
of any door. Fits all Arrow
storage buildings.

6

Model No. SS404

• Makes 8" to 12" (20-30cm)
wide shelves in any length.

• Brackets, braces,
hardware included.
Lumber is not included.

* Some drilling required to fit buildings without mid-wall bracing.

Model No. SS900-A

• Grey color

• 3 shelves

• Holds up to 85 lbs. (38kg)
(even weight distribution)

THIS

PAGE

WA S

LEFT

BLANK

INTENTIONALLY

7

THIS

PAGE

WA S

LEFT

BLANK

INTENTIONALLY

8

Foundation

A09

The Foundation For Your Building

OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB109-A or 68385-A)

Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one
of the following:

A. To support a plywood deck B. To be filled with sand. We recommend the combined use of

1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground.
Allow 1 - 2 hours for construction.

OPTION 2: Wood Platform

If you decide to build your own foundation, be sure to select the appropriate materials.
These are the recommended materials for your foundation:

● 2 x 4's (5cm x 10cm) Pressure Treated Lumber ● 5/8" (1,5cm) 4 x 8 (122cm x 244cm) Plywood-exterior grade

● 10 & 4 penny Galvanized Nails ● Concrete Blocks (optional)

The platform should be level and flat (free of bumps, ridges etc.)
to provide good support for the building. The necessary materials
may be obtained from your local lumber yard.

To construct the foundation follow instructions and diagram.

Construct frame (using 10 penny galvanized nails)
Measure 16"/24" (40,6cm/61cm) sections to construct
inside frame (see diagram)
Secure plywood to frame (using 4 penny galvanized nails)

Allow 6 - 7 hours for construction.

Note: Platform/Slab will extend 9/16" (1,4cm) beyond floor

frame on all four sides. Seal this 9/16" of wood with a

OPTION 3: Concrete Slab

The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.
The following are the recommended materials for your foundation.

● 1 x 4's (2,5cm x 10cm) (will be removed once the concrete cures)

● Concrete ● Sheet of 6 mil plastic

● We recommend for a proper strength concrete to use a mix of:
1 part cement ● 3 parts pea sized gravel ● 2 1/2 parts clean sand

Prepare the Site/Construct a Foundation

1. Dig a square, 6" (15cm) deep into the ground (remove grass).

2. Fill up to 4" (10cm) in the square with gravel and tamp firm.

3. Cover gravel with a sheet of 6 mil plastic.

4. Construct a wood frame using four planks of 1x4 (2,5cm x 10cm)
lumber.

5. Pour in concrete to fill in the hole and the frame giving a
total of 4" (8-10cm) thick concrete. Be sure surface is level.

Allow 3 - 5 hours for construction and a week for concrete curing time.

FRONT

(DOOR)

roofing cement (not included), or bevel this 9/16" of

concrete when pouring, for good water drainage.

FRONT

(DOOR)

Note: Finished Slab dimensions, with lumber removed.

121"

3,1m

121"

3,1m

40,6cm/61cm

92 3/4"

2,4m

92 3/4"

2,4m

16"/24"

9

Anchoring

A10

Anchoring Down The Building

It is important that the entire floor frame be anchored after the building is erected.

Below are recommended ways of anchoring.

Arrow Anchoring Kit: (Model No. AK4 or 60298)

Recommended for use with any suggested base.
Contains: 4 Anchors with Cable, Clamps and

installation instruction.

Anchoring into Wood/Post:

Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia.
holes provided in the frames for proper anchoring.

1. 2.

OVER THE BEAMS

AND INTO THE GROUND

Arrow Anchoring Kit: (Model No. AK100 or 68383)

Recommended for use with the concrete foundation.
Contains: Corner gussets, perimeter clips, hardware,

1/4" masonary drill bit and installation instruction.

Anchoring into Concrete:

1. For poured concrete slab or footing or patio blocks:
Use 1/4" x 2" Lag Screws.

2. For Anchor Post of Concrete poured after building is
erected: Use 1/4" x 6" Lag Screws.

1.

2.

10

A11

#8-32 Hex Nut (163)

65103

Hardware

Remove from bag of screws

and save for the last step

65900A

#10Bx1/2" Black Screw (8)

(Packed with Screws)

65923

#8-32x3/8" Bolt (163)

65004

#8Ax5/16" Screw (328)

66045

Handle (2)

66769

Door Slide (4)

66646

Washer (377)

(10 sheets of 40)

66382

Lower Door Guide (4)

65109

#8-32 Acorn Nut (4)

(Packed with Screws)

66183

Roof Trim Cap

(2 right & 2 left)

67468

Peak Cap (2)

(Arrow Logo)

6228

Track Support (2)

5971

Roof Beam Bracket (4)

67293

Weather Stripping (1)

11

A12

Parts List

Assembly Part Part Quantity Check
Key No. Number Description in Carton List

1 3719 Door Handle Brace 2
2 9364 Wall Panel (Side) 4
3 9372 Front Wall Panel 2
4 9365 Front Wall Channel 2
5 5986 Rear Wall Angle 2
6 6000 Right Gable 2
7 6001 Left Gable 2
8 10497 Horizontal Door Brace 4
9 9355 Vertical Door Brace 2
10 6403 Door Track Splice 1
11 9366 Door Track 2
12 8995 Wall Panel 6
13 6529 Roof Panel 2
14 6635 Gable Brace 2
15 10489 Right Door 1
16 10489 Left Door 1
17 7483 Roof Panel 4
18 9900 Door Jamb 2
19 9917 Rear Wall Channel 2
20 8468 Right Roof Panel 2
21 8469 Left Roof Panel 2
22 8485 Left Side Roof Trim 2
23 8840 Ridge Cap 1
24 10470 Roof Beam 8
25 8836 Right Side Roof Trim 2
26 9922 Side Wall Channel 4
27 8839 Side Wall Angle 4
28 8486 Ridge Cap 1
29 8934 Ramp 1
30 9367 Front Floor Frame 2
31 8936 Rear Floor Frame 2
32 8937 Side Floor Frame 4
33 9362 Corner Panel 4

12

A13

Assembly by Key No.

33

11

32

20

27

3

25

4

2

24

26

18

17

7

16

12

8

9

10

1

13

24

32

22

27

24

26

14

1

21

17

28

24

33

2

12

6

8

11

9

15

18

6

24

3

24

21

23

24

19

14

17

31

33

5

12

24

13

22

27

20

17

7

25

5

12

27

19

12

2

12

2

26

33

26

31

30

8

29

8

30

4

32

32

13

Step 1

A14

The front floor frame is made up of
three pieces. The side floor frames
and the rear floor frame are made up
of two pieces. The holes in these
pieces will align when the pieces are
positioned with correct amount of
overlap. The illustrations below show
the proper overall length for the sides,
rear and front. Proceed as follows:

● Parts Needed For ●

Floor Frame Assemblies

9367

8934

8937

●●

● 8934 Ramp (1)

●●

●●

● 9367 Front Floor Frame (2)

●●

●●

● 8936 Rear Floor Frame (2)

●●

●●

● 8937 Side Floor Frame (4)

●●

9367

8936

1 Place the front floor frames as

shown. Center the ramp, with drain
holes facing outside, on top of the two
front floor frames. Join the frames by
inserting eight screws.

2 Overlap the side floor frames and

the rear floor frames as shown. The
holes in these pieces will align when
the pieces are positioned with cor­rect amount of overlap. See the illus­trations below for the proper overall
length of the side and rear floor frames.
Join the frames by inserting four/five
bolts into each frame set as shown.

3 Double check the length of each

and set these pieces aside for later
use.

STEP

1

STEP

2

9367

8937

8934

DRAIN HOLES FACE

OUTSIDE

Side Floor Frame 91 1/8" 2,3m

8937

Rear Floor Frame 119 3/8"

8936 8936

Front Floor

Frame Assembly

119 3/8" 3,0m

9367

3,0m

14

STEP

3

91 1/8" 2,3m

91 1/8" 2,3m

119 3/8" 3,0m

Front & Rear

119 3/8" 3,0m

Step 2

A15

The main frame pieces reinforce the
walls. These pieces will later be in­stalled in the center and at the top
edge of the side walls and the rear
wall. Proceed as follows:

1 Overlap the rear wall channel

pieces as shown in the figure and
fasten the two pieces together with

one bolt in the center hole

holes will align).

(three

● Parts Needed For ●

Frame Assemblies

9917

9922

●●

● 5986 Rear Wall Angle (2)

●●

●●

● 9917 Rear Wall Channel (2)

●●

●●

● 9922 Side Wall Channel (4)

●●

● ●

● 8839 Side Wall Angle (4)

● ●

Rear Wall Channel

118 1/8" 3,0m

9917

Side Wall Channels

89 7/8" 2,3m

9922

2 Make two side wall channels by

overlapping the side wall channel
pieces as shown. Fasten each set
together with

hole

of each set.

one bolt in the center

3 Overlap the rear wall angle

pieces as shown in the figure and
fasten them together with

one bolt in

the center hole.

4 Make two side wall angles by

overlapping the side wall angle piec­es as shown. Fasten each set togeth­er with

one bolt in the center hole.

8839

5986

STEP

1

STEP

3

STEP

2

Rear Wall Angle
118 1/8" 3,0m

5986

Side Wall Angles

89 7/8" 2,3m

8839

STEP

4

Rear Wall Channel

118 1/8" 3,0m

5 Set the assemblies aside. You will

use them later.

STEP

5

Side Wall Channels

89 7/8" 2,3m

Rear Wall Angle
118 1/8" 3,0m

Side Wall Angles

89 7/8" 2,3m

15

Step 3

D16

The roof beams join the two gables
and support the roof panels. The main
roof beam is made up of four pieces
overlapped back to back at the cen­ter. The left and right roof beam as­semblies are made up of two pieces.
Hint: These pieces are force-fitted,
so you may have to press hard to join
them together.

● Parts Needed For ●

Roof Beam Assemblies

10470

●●

● 10470 Roof Beam (8)

●●

10470

1 Place the end of one roof beam

inside a second roof beam so that the
six holes in each piece align. Make
four sets of roof beams by repeating
this procedure.

Do not insert bolts

yet.

2 Take two of the pressed-together

roof beams and join them as shown
to form the main roof beam assembly.
Hold the assembly together and fas­ten with 14 bolts. Build

only one

Doubled Beam Assembly.

3 Fasten the other two pressed-

together roof beams with eight bolts
to make the left and right roof beam
assemblies.

STEP

1

STEP

2

10470

ASSEMBLED

END
VIEW

10470

Roof Beam 91 7/8" 2,3m

Build

one

Doubled Main Roof

Beam Assembly for Peak in Roof

4 Set these pieces aside for later

assembly.

Build

16

STEP

3

two

Single Beam Assemblies

10470

10470

91 7/8"
2,3m

91 7/8"
2,3m

Step 4

A17

The door track assembly supports
the sliding doors and reinforces the
front wall. It is made up of three pieces.

1 Using the door track splice,

(painted), join the door track
(galvanized) pieces end-to-end as
shown.

● Parts Needed For ●

Door Track Assembly

NOTE:

Door Track Splice (painted part)

6403

●●

● 6403 Door Track Splice (1)

●●

●●

● 9366 Door Track (2)

●●

2 Insert four screws

from the under-

side only.

Hint: The holes in the top side of the
door track assembly are for fastening
the gable to the top of the front wall in
a later step.

3 Position door slides onto the

legs, from the end of door track
assembly, as shown in the end view.

STEP

118 1/8" 3m

STEP

1

9366

6403

STEP

2

STEP

66769

9366

Long Leg
on Top

Short Leg
on Bottom

9366

9366

4 Set this piece aside for later use.

END VIEW

66769

3

118 1/8" 3m

118 1/8" 3m

4

17

Step 5

A18

● Parts Needed For ●

Floor Frame

●●

● Front Floor Assembly (1)

●●

●●

● Side Floor Assembly (2)

●●

●●

● Rear Floor Assembly (1)

●●

RIGHT
REAR

8937

1 Assemble the four corners of the

floor frame using two screws at each
corner as shown. At the front corners
fasten bolts through from
the bottom with nuts on top.

2 Measure the floor frame diago-

nally. When the diagonal measure­ments are equal, the floor frame is
square.

STEP

1

FRONT

8936

RIGHT
FRONT

8937

9367

When Diagonal Measurements
are Equal the Floor Frame
is Square.

NOTE

If using a wood platform or

concrete slab do not fasten the

floor frames to your base at this

time. You will anchor the

building after it is erected.

NOTE

If you have purchased a Floor

Frame Kit you need to

install it at this time.

The floor frame

and level

18

or holes will not align.

must be square

STEP

2

Level

Step 6

A19

● Parts Needed For ●

Corners

●●

● 8995 Wall Panel (2)

●●

●●

● 9372 Front Wall Panel (2)

●●

●●

● 9362 Corner Panel (4)

●●

NOTE

The remainder of the building assembly

requires many hours and more than one

person. Do not continue beyond this point

if you do not have enough time to com-

plete the assembly today. A partially

assembled building can be severely

damaged by light winds.

Each screw and bolt in the wall re­quires a washer.

1 Position a corner panel at the

corner of the floor frame as shown.
The widest part of each corner panel
must be placed along the side of the
building for all four corners. Fasten
the corner panel to the floor frame
with one screw.

Support the corner panel with a step
ladder until a wall panel is attached.

STEP

1

Narrow
Side

9362

Wide Side

REAR

SIDE TOP VIEW

9362

FRONT

8995

9362

SIDE

9362

8995

2 Attach the front wall panels to the

front corner panels, as shown. A small
gap will exist between front wall panel
and ramp.

3 Attach the wall panels to the rear

corner panels, as shown.

NOTE

Be careful to install the correct

panel in each position as shown

4 Double-check the part numbers of

the wall panels, before proceeding.

The floor frame

and level

or holes will not align.

must be square

STEP

4

9362

9372

9362

9372

9372

STEP

2

8995

STEP

8995

9362

3

9372

Crimped Rib
Underneath

9362

Washer

Panels rest on
frame as shown

19

Step 7

A20

The main frame pieces give rigidity to
the side walls and provide a surface
for attaching the gables which sup­port the roof.

1 Fasten the rear wall angle as-

sembly across the inside top of the

rear wall using screws.

2 Fasten the rear wall channel as-

sembly across the middle of the rear

wall using screws.

● Parts Needed For ●

Frames

Wall Angles
Must Face
Inside
Building

STEP

1

STEP

2

FRONT

●●

● Door Track Assembly (1)

●●

●●

● Rear Wall Angle Assembly (1)

●●

●●

● Side Wall Angle Assemblies (2)

●●

●●

● Rear Wall Channel Assembly (1)

●●

●●

● Side Wall Channel Assemblies (2)

●●

5986

9917

3 Fasten the side wall angles across

the inside top of the side panels us­ing screws. Side wall angles must
overlap rear wall angle in corners.

4 Fasten the side wall channel

assemblies across the middle of the

side panels using screws. Fasten
overlaps in rear corners with screws.

5 Fasten the door track assembly

(holes on top) across the top of the
front wall panels using screws. See
the figure.

STEP

3

9366

8839

STEP

4

Door Track Assembly

9922

FRONT

Long Leg
on Top

Opening
Facing in

Short Leg
on Bottom

NOTE

The wall channels behind the

front wall panels will be installed

in a later step.

20

STEP

5

FRONT

Step 8

A21

● Parts Needed For ●

Wall Panels

●●

● 9364 Wall Panel (4)

●●

●●

● 8995 Wall Panel (4)

●●

The wall panels come in two widths.
Each wall panel has a crimped rib on
one side. The crimped rib should go
under the rib of the panel that follows
it.

1 Locate all of the wall panels and

set each one alongside the building.

2 Be sure that you have the correct

panels in each position. Do this by
overlapping the panels and deter­mining if the holes line up with the
holes in the frame.

3 Fasten the wall panels at the top

and bottom with screws.

9364

STEP

1

9364

8995

Panels rest on
frame as shown

Crimped Rib
Underneath

8995

8995

STEP

2

9364

8995

9364

Detail Showing
Center of Panel Screwed
to Wall Channel

4 Fasten the center of each panel to

the wall channel with screws. Fasten
overlapping ribs as before.

5 When you have attached all wall

panels in the correct positions, the
building will look like this.

STEP

3

Use bolts and
nuts thru wall
angle overlaps
at the top of
panel at sides
and rear.

STEP

STEP

4

Bolt and nut
does not go thru
wall channel
at overlap

5

21

Step 9

A22

Front Channel/Door Jamb

The door jambs reinforce the door
opening and provide an attractive
trim. Follow these steps for both
door jambs.

● Parts Needed For ●

9365

●●

● 9900 Door Jamb (2)

●●

●●

● 9365 Front Wall Channel (2)

●●

1 Fasten the front wall channels

in their positions between the end of
the side wall channel and the cor­ner panel using screws. Do not put
a screw in the hole at the end be­hind the door opening at this time.

2 Fasten a door jamb to the front

panel with two bolts, nuts and acorn
nuts, as shown.

3 Fasten the center of the door

jamb to the front wall panel and the
front wall channel with two screws.

Acorn Nut

Hex Nut

Acorn Nut

STEP

1

STEP

2

9900

FRONT

FRONT

INSIDE OF
BUILDING

(2) bolts

Bolt

Screw

TOP VIEW

Front Wall Channel

Door Track

9900

TOP VIEW

Front Wall Channel
Cross-Section
Top View

Screw

STEP

3

4 Fasten the top of the door jamb to

the door track with two screws. Do
the same for the bottom into frame.

Repeat steps 2 through 4 for the

opposite

22

door jamb.

STEP

4

Screw

TOP VIEW

Door Track

Screw

Step 10

A23

The gables go on top of the front and
rear walls to support the roof beams.

NOTE

The gables are packed nested

together and might be mistaken

as one piece. Carefully separate

them before continuing.

1 Attach the four roof beam

brackets to the gables using two

bolts, washers and nuts.

NOTE

Mounting leg of bracket must

face toward center of gable

and holes closest together

must be on top

● Parts Needed For ●

Gable Assemblies

●●

● 6000 Right Gable (2)

●●

●●

● 6001 Left Gable (2)

●●

●●

● 5971 Roof Beam Bracket (4)

●●

STEP

1

6000

5971

Roof Beam Brackets

FRONT

Washer

6001

23

Step 11

A24

1 Lift and fasten a right and left

gable, under angle at corner, to the
door track and rear wall angle with
screws.

Hint: On the rear gable, use a bolt
and nut at the overlapping rear wall
angle. On the front gable, leave out 2
screws closest to center gable leg.

2 Join the left and right gables

together with a gable brace using a
bolt and nut in the bottom hole

only.

● Parts Needed For ●

Gables/Braces

●●

● Left Gable Assemblies (2)

●●

●●

● Right Gable Assemblies (2)

●●

●●

● 6635 Gable Brace (2)

●●

3 Repeat Steps 1 & 2 for the door

track on the front of building, except
for the track supports, fasten as
shown.

STEP

STEP

1

Gable

Track Supports 6228

6635 Gable Brace

STEP

2

24

3

Step 12

A25

1 Spread the two halves of the main

roof beam and fasten the roof beam

to the gable brace of the front gable.

● Parts Needed For ●

Roof Beams

STEP

3

●●

● Main Roof Beam (1)

●●

●●

● Single Roof Beam (2)

●●

2 Fasten the other end of the main

roof beam to the gable brace of the
rear gable.

3 Fasten the single roof beams,

small holes on top,

bolts and nuts.

as shown using

Single Roof Beam Assembly

STEP

2

Spread Two Halves
Of Roof Beams

STEP

1

Main Roof Beam Assembly

25

Step 13

A26

● Parts Needed For ●

Right Roof Panel

STEP

●●

● 8468 Right Roof Panel (1)

●●

Installing the roof panels is best done
with a step ladder. Begin installing
roof panels at the back right corner of
the building. Each screw and bolt in
the roof requires a washer.

NOTE

Measure the building diagonally

again and make adjustments to

make sure the building is square.

This will make the roof panels fit

better, and holes will align.

NOTE

If a Roof Beef-Up Kit was

purchased, assemble prior to

attaching the roof panels.

STEP

2

8469

7483

6529

7483

8468

8

10

4

1

2

6

1

5

7

9

3

8468

7483

6529

7483

8469

FRONT

1 Locate the roof panels by their

numbers.

position they are to be installed.

Note the sequence and

2 Position the right roof panel at the

back right corner and fasten to the
gable with 5 bolts and nuts and roof
beams using 2 screws.

the lower end of the panel to the side
wall angle at this time.

Hint: Attach fasteners in order shown
in diagram.

Do not fasten

FRONT

Nut

Washer

Gable

Bolt

8468 Right Roof Panel

6

7

1

2

3

4

5

26

Step 14

A27

● Parts Needed For ●

Roof Assembly

●●

● 8468 Right Roof Panel (1)

●●

●●

● 8469 Left Roof Panel (2)

●●

●●

● 7483 Roof Panel (2)

●●

●●

● 6529 Roof Panel (2)

●●

1 Install a left roof panel at the left

rear and right front corner of the roof.
Install a right roof panel at the left
front corner of the roof.

2 Cut 4 short 2" (5cm) strips off the

roll of weather stripping tape, and
put them aside. Cover the joint at the
peak with weather stripping tape.
Unroll the tape and press it down
over the opening at the ridge as you
install each roof panel. Do not cut the
tape at this time.

3 Install 2 narrow and 2 wide roof

panels in the sequence and posi-

tions shown on previous page.

not fasten the lower end of the panels
to the side wall angles at this time.

Continue weather stripping the ridge
opening.

Do

8469 Left Roof Panel

7483 Roof Panel

6529 Roof Panel

8468 Right

Roof Panel

FRONT

STEP

1

Weather Stripping

Tape Roll

STEP

2

7483 Roof Panel

6529 Roof Panel

STEP

3

NOTE

Narrow roof panel crimped rib is

overlapped by wide rib of

adjacent panel where possible.

NOTE

If roof beam holes do not line up

with the roof panel holes, shift the

building from left to right.

If this does not help, your building

may not be level. Shim the
corners until holes line up.

Fasten At

Overlap with

Bolt

Screws To

Roof Beam

Screws To

Roof Beam

Fasten At

Overlap with

Bolt

Do not fasten

at this time

27

Step 15

A28

1 Install the first ridge cap on the

completed roof section using bolts
and nuts. Fasten roof panel overlaps
not used for ridge cap. Cover the
head of bolt with the 2" (5 cm) piece of
weather stripping tape. Do not fasten
the ends of the ridge cap at this time.

2 Install the second ridge cap over-

lapping the first ridge cap while in­stalling the remaining narrow roof
panels. Continue weather stripping
the ridge.

● Parts Needed For ●

Ridge Caps & Panels

STEP

1

●●

● 8840 Ridge Cap (1)

●●

●●

● 7483 Roof Panel (2)

●●

●●

● 8486 Ridge Cap (1)

●●

8840

Strips

3 Fasten the lower end of the panels

to the side wall angles using screws
and washers. Use bolts and nuts
through wall angle overlaps at the
bottom of the panel.

Cut Weather

Stripping and

Fold Under

7483

8486

STEP

2

28

7483

STEP

3

Step 16

A29

1 Attach the right and left side roof

trim to the lower end of the roof pan-

els on each side of the building using
screws at each panel overlap.

NOTE

A single screw fastens both trim

pieces at the overlap.

2 Using your thumb and index fin-

ger, overbend the bottom flange of
the roof panel rib at the corner inward
enough so the right and left roof trim
caps fit onto right and left corners.

3 Fasten the roof trim caps to the

side trim using a screw.

● Parts Needed For ●

Roof Trim

STEP

1

8485

Roof Trim

8836

●●

● 8485 Left Side Roof Trim (2)

●●

●●

● 8836 Right Side Roof Trim (2)

●●

8836

4 Fasten the roof panel ribs, peak

caps and ridge caps together using

bolts and nuts.

Peak Cap

STEP

4

Roof Trim Cap

STEP

2

STEP

3

8485

Tuck Flange
Inward to Fit

Inside of

Roof Trim Cap

29

Step 17

A30

The steps on this page tell how to
assemble the right door. You will
perform exactly the same procedures
for the left door. Each bolt and screw
in the door requires a washer. Pro­ceed as follows:

1 Attach the door handle brace and

handle to the door with 1 bolt as

shown.

Don't tighten the bolt yet.

● Parts Needed For ●

Door Assembly

10497

9355

●●

● 3719 Door Handle Brace (2)

●●

●●

● 10489 Right and Left Doors (2)

●●

●●

● 10497 Horizontal Door Brace (4)

●●

●●

● 9355 Vertical Door Brace (2)

●●

66045

3719

66045

3719

2 Swing the door handle brace up to

the hole in the center of the door and
insert a screw.

3 Hold the vertical door brace

against the center of the inside sur­face of the door and turn the screw to
hold the vertical door brace and door
handle brace in place. Fasten to
door above and below center
connection using 2 screws.

4 Insert a second bolt in the door

handle and tighten both bolts.

5 Put a horizontal door brace onto

the top edge and bottom edge and
fasten

with 1 bolt in the center.

66382

9355

STEP

66382

STEP

10489 Right Door
10489 Left Door

STEP

4

STEP

STEP

1

10497

6 Attach the lower door guides and

bolts as shown.

7 Repeat steps 1 through 6 for the

left door.

30

STEP

6

2

3

66382

5

END VIEW
SHOWING:

Horizontal

Door Brace

10497

Door

Washer

Guide

Step 18

A31

● Parts Needed For ●

Door Installation & Adjustment

●●

● Right Door Assembly (1)

●●

●●

● Left Door Assembly (1)

●●

1 From inside the building, put the

bottom of the right door assembly (on
your left when you are inside the
building) behind door jamb into the
front frame track.

2 Position the top of the door so that

the holes in the door line up with the
holes in the door slides.

3 Fasten the door to the door slides

using two #10Bx1/2" screws per door
slide.

Gable

Door Track

Door Slide

Front Floor Frame Assembly

Horizontal Door Brace

Door

STEP

1

STEP

2

Door Slide

NOTE

The holes in the door slides allow

you to adjust the doors. Place the

door in the middle holes.

4 Repeat steps 1 through 3 for the

left door.

Adjustment Holes

Adjustment Holes Allow

Doors to Meet Evenly

Along Their Length

#10Bx1/2" Screw

STEP

3

Right Door Left Door

STEP

4

Keep this Owner's Manual and Assembly Instructions for future reference.

31

A 3 2

EN108-A HM108-A MN108-A NP108

NW108-A PD108-A SA108-A VN108-A

SOME FACTS ABOUT RUST

Rusting is a natural oxidizing process that occurs
when bare metal is exposed to moisture. Problem
areas include screw holes, unfinished edges, or
where scrapes and nicks occur in the protective
coating through normal assembly, handling and
use. Identifying these natural rusting problem areas
and taking some simple rust protection precautions
can help to stop rust from developing, or stop it
quickly as soon as it appears.

1. Avoid nicking or scraping the coating surface,
inside and out.

2. Use all the washers supplied. In addition to pro­tecting against weather infiltration, the washers pro­tect the metal from being scraped by the screws.

3. Keep roof, base perimeter and door tracks free of
debris and leaves which may accumulate and retain
moisture. These can do double damage since they
give off acid as they decay.

4. Touch up scrapes or nicks and any area of visible
rust as soon as possible. Make sure the surface is
free of moisture, oils, dirt or grime and then apply an
even film of high quality touch-up paint.

709291207