ArmyTek Viking Pro XHP50, Viking Pro XP-L User guide

Warnings

Model

Viking Pro XHP50

Viking Pro XP-L

LED

Cree XHP50

Cree XP-L

Optics

Orange Peel Reflector

Smooth Reflector

Brightness stabilization type

FULL (constant light)

Light output, LED / OTF lumens*

2300 / 1800

1250 / 1050

Peak beam intensity, candelas

20500

33500

Hotspot / spill

10° / 8 0°

5° / 40°

Beam distance*

286 meters

366 meters

Modes, light output (OTF
lumens*) and runtimes
(measured with 18650 Li-Ion
3400mAh until the light output
drops to 10% of the initial
value)

Turbo2

1800 lm / 1h

1050 lm / 1.3h

Turbo1

900 lm / 1.7h

750 lm / 1.8h

Main3

390 lm / 4h

410 lm / 3.5h

Main2

165 lm / 10.5h

190 lm / 8.5h

Main1

30 lm / 50h

32 lm / 36h

Firefly2

1.7 lm / 40d

2.5 lm / 18d

Firefly1

0.15 lm / 200d

0.4 lm / 100d

Strobe2

15Hz / 1800 lm / 2h

15Hz / 1050 lm / 2.7h

Strobe1

15Hz / 165 lm / 22h

15Hz / 190 lm / 17h

Power source

1x18650 Li-Ion / 2x18350 Li-ion** / 2xRCR123 Li-ion** / 2xCR123A

Size and weight (without batteries)

Length 154mm, body diameter 25.4mm, head diameter 41mm, weight 126g

1. Always follow the instructions from this manual and recommendations on battery usage.

2. Apply only the recommended power sources.

3. Do not reverse battery polarity.

4. Do not use different power sources together, i.e. old ones with new ones, charged with

discharged. Do not use different types of batteries combined as the element with less
capacity can be damaged.

5. Do not modify or recast the flashlight and its components as it will deprive you of the

warranty.

6. Do not allow water or any other liquid to leak into the flashlight.

7. Do not aim a switched-on flashlight at people's or animals' eyes – it can cause temporary

blindness.

8. Do not allow children to use the flashlight without your assistance.

The producer will not be liable for any harm done to the user if it was caused by
improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old grease once or twice per year. Remember that reliable protection
from water and dust cannot be provided by worn out sealing. The fouling as well as lack of lubricant cause fast wear-out of threads and
sealing rings. To clean the threads do the following:

1. Unscrew the tailcap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).

2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged

replace it by a new one.

3. Clean the metal threads with a brush using ethanol. Be careful not to allow the applied liquid to get inside the flashlight or tailcap as

it can cause fails in functionality of the flashlight.

After cleaning lubricate the thread and the sealing ring with polyalphaolefin-based silica grease, e.g. Nyogel 760G.The application of
automotive and other improper grease can cause swelling and damage of the sealing rings.

In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts
as often as required.

In case the rubber button is damaged, it should be replaced. You can also replace the switch with
the spring in the same way. Replacement order:

1. Unscrew the tailcap.

2. Unscrew the first washer inside it to take out the switch. To do so you should use needle-

nose pliers (round-nose pliers or another tool, the most suitable will be expansion pliers).
Use the tool as it is shown at the picture. To replace the rubber button unscrew the second
washer under the switch.

3. Replace the rubber button and assemble the parts in inverse sequence.

Viking

THE MOST TECHNICALLY ADVANCED

USER MANUAL

Thank you for choosing the products of Armytek Optoelectronics Inc., Canada.

Please read this manual carefully before using the flashlight.

Specifications

Armytek Optoelectronics Inc. is a Canadian manufacturer that produces powerful and reliable flashlights designed especially for your
needs. The components made in the USA and Japan. .10 years no-hassle warranty

§ Amazing brightness – LED lumens.up to 2300

§ Extremely far throw up to meters.370

§ Comfortable light 5:40 for efficient hunting with shotguns.

§ Constant brightness even in -25°C frost and with almost discharged batteries.

§ The highest IP68 dust- and waterproof standard – more than 5 hours at 50 meters depth.

§ Reliable body, red/green/blue filters and original remote switches for comfortable Hunting and secure Military application.

§ Guaranteed durability – stands up the recoil of any gun gauge and falling from 30 meters height.

§ Record runtime with 1x18650 Li-Ion battery in Firefly mode – 100 days.

Do not disassemble the flashlight except for unscrewing the thread ring gage and replacing the rubber button. There are no
other parts in the flashlight that can be replaced by the user.

Armytek provides free warranty repair for 10 years (excluding batteries, chargers, switches and connectors which have 2 years
warranty) from the date of buy with the document confirming the purchase.

Guarantee does not extend to damage during:

1. Improper usage.

2. Attempts to modify or repair the flashlight by nonqualified specialists.

3. Longtime application in chlorinated or polluted water, or other liquids (other than water).

4. High temperatures and chemicals' exposure (including the exposure of liquid from defected batteries).

5. Usage of low-quality batteries.

Web: www.armytek.com Email: [e-mail]

Address: 13-85 West Wilmot St, Richmond Hill, Ontario, L4B 1K7, Canada

Specifications are subject to change without notice.

Service and Warranty

Armytek Optoelectronics Inc.

* Light output for flashlights with Warm light are about 7% less, beam distances are about 3% less.
** It is allowed to use only protected Li-Ion batteries.

Set description

Operation

4

x2

1

3

5

2

6

7

8

Viking

Items included in the package:
1 - Flashlight
2 - Clip
3 - Rubber grip
4 - Lanyard

ь Your flashlight can inconsiderably differ from the pictures in the manual.
ь The producer reserves the right to change the package at his own discretion without modifying this manual.

1. 2.

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

ь We DO NOT RECOMMEND to use low-quality CR123A batteries, because they can explode. Turbo mode needs

rechargeable 18650 Li-Ion batteries without PCB (unprotected) or with PCB which guarantees 7A discharge current
for stable work.

ь We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries can leak for various reasons

and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in then use new and high-
quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least once a
month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also recommended to
replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

Active temperature control. The flashlight can quickly heat up in Turbo mode. When the temperature becomes +60°C – the
brightness decreases by small steps. After cooling-down (provided that battery voltage is sufficient) the brightness increases to the
Turbo mode again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good
air-cooling the flashlight delivers light without stepping down even in Turbo mode. There are no preset timers for stepping, but real-
time active temperature measurements.

5 - Holster
6 - Spare rubber button
7 - 2 spare O-rings
8 - User manual

Initial Service

3.

Change Hunting/Tactical settings

Unscrew & Tighten up x10

x10

Constant light

Tighten up

Strobe

Unscrew to 1/8

Half Press & Release (no click)

1/2

Unscrew & Tighten up

Turbo

гд

Main2

Tighten up & Unscrew

Strobe2

гд

Strobe1

Half Press (no click) x15 & Click x1

1/2

Low Battery Indication. If the brightness is <25% from the nominal value, the LED flashes 2 times ONCE (after 30sec from switching

on). If you are not sure if it flashed or not switch the flashlight off and on: in case the battery is low flashes will repeat. Light output
decreases to Firefly mode at critical level.

Click x1

Click x1

Cycling through Additional modes

Strobe

Main3

Change Constant modes

Change Strobe modes

How to change Turbo1 & Turbo2

x15

Turbo

Additional modes

Firefly1

*

Firefly2

Main1

Main2

* if enabled

Momentary on – any mode switched on by half-pressing of the

button (no click!) and active till the button is released. It is suitable
for giving signals by short button pressings. Click the button to

switch the light on permanently.

Hunting settings – comfortable modes for hunting. It’s set by
default. Turbo mode (when the head is tightened up) and

Additional modes with constant light (changed by click with the
head unscrewed to 1/8). Remote switch can be used in Turbo.

Tactical settings – made for Special forces and Airsoft. Constant
light (when the head is tightened up) and Strobe mode (when the
head is unscrewed to 1/8). There are 2 Strobe modes and 2
Constant light modes for selection. Remote switch can be used in
ANY mode.

How to change the settings from one to another – unscrew and
tighten up the head of the flashlight at least 10 times (while
rotation you will change the modes). The pause must be <1 sec.

Hunting settings:

Turbo. Tighten the head of the flashlight if it is unscrewed. First full

click of the button turns the light on. Second full click turns it off.

Additional modes (2 Firefly + 3 Main + Strobe (if enabled)). If the
head of the flashlight is tightened up, unscrew it for 1/8 of a circle.

Full click of the button turns the light on at the last used Additional
mode.

Cycling through Additional modes. To switch the mode turn the
flashlight off and on (by full click or half-pressing). The modes
switch cyclically: Firefly1 – Firefly2 – Main1 – Main2 – Main3 –

Strobe (if enabled).

How to add/ remove Strobe in Additional modes. Switch on the
flashlight by half-pressing of the button at least 20 times. Last
switch should be clicked completely. The flashlight blinks,
confirming the action.

Tactical settings:

Constant light. Tighten the head of the flashlight if it is unscrewed.

First full click of the button turns constant light on. Second full
click turns it off. Also you can switch it on by half-pressing of the
button (no click).

Change Constant modes. The head is tightened up: unscrew it for
1/8 and tighten up again – Turbo and Main2 will switch cyclically.

Strobe. If the head is tightened up, unscrew it for 1/8 of a circle.
First full click of the button turns Strobe on. Second full click turns
it off. Also you can switch it on by half-pressing of the button (no

click).

Change Strobe modes. The head is unscrewed: tighten up and
unscrew it for 1/8 again – Strobe1 and Strobe2 will switch
cyclically.

How to set Turbo1 and Turbo2. Switch on the flashlight by quick
half-pressing of the button at least 15 times. Last switch should be
clicked completely. The flashlight blinks once (confirming the
selection of Turbo1) or 2 times (confirming the selection of
Turbo2).

Lock-out function. Unscrew the tailcap to 1/4 for the protection
from accidental switching on.

Automemorizing. After switching off the last used Mode is
memorized for quick 1-click access at next switching on.