Ariens 921038, 921040, 921029, Platinum 24 SHO, Platinum 30 Owner's/operator's Manual
...
Platinum Series
E10
Sno-Thro
®
Owner/Operator Manual
Manuel du Propriétaire/Utilisateur
921038 – Platinum 24 SHO
921040 – Platinum 30 SHO
Models
921029 – Platinum 30
(SN 100000+)
(SN 000101+)
(SN 000101+)
The use of any gasoline exceeding 10% ethanol (E10) or
10% MTBE will void the product warranty.
L’utilisation d’une essence contenant plus de 10%
d’éthanol (E10) ou de 10% de MTBE annulent la garantie.
ENGLISH
FRANÇAIS
04754100A • 6/14
Printed in USA
TABLE OF CONTENTS
Figure 1
Serial Number Label
SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 9
CONTROLS and FEATURES. . . . . . . . 16
OPERATION . . . . . . . . . . . . . . . . . . . . . 17
MAINTENANCE . . . . . . . . . . . . . . . . . . 23
SERVICE AND ADJUSTMENTS . . . . . 26
INTRODUCTION
MANUALS
Before operation of unit, carefully and
completely read your manuals. If used
improperly, this unit could be dangerous and
cause personal injury or property damage.
The contents will provide you with safety
instructions for the safe use of your unit
during normal operation and maintenance.
All reference to left, right, front, or rear are
given from operator standing in operation
position and facing the direction of forward
travel.
ENGINE MANUAL
The engine on this unit is covered by a
separate manual specific to the engine. This
manual is included in the literature package
that shipped with the unit. Refer to this
manual for engine service recommendations.
If the engine manual is not available, contact
the engine manufacturer for a replacement
manual.
MODEL AND SERIAL NUMBERS
When ordering replacement parts or making
service inquiries, know the Model and Serial
numbers of your unit and engine.
Numbers are located on the product
registration form in the unit literature
package. They are printed on a serial number
label, located on the frame of your unit.
STORAGE. . . . . . . . . . . . . . . . . . . . . . . 33
SERVICE PARTS . . . . . . . . . . . . . . . . . 35
ACCESSORIES. . . . . . . . . . . . . . . . . . . 35
TROUBLESHOOTING . . . . . . . . . . . . . 34
SPECIFICATIONS. . . . . . . . . . . . . . . . . 36
WARRANTY . . . . . . . . . . . . . . . . . . . . . 37
• Record unit model and serial numbers
here.
• Record engine model and serial
numbers here.
PRODUCT REGISTRATION
The Ariens dealer must register the product
at the time of purchase. Registering the
product will help the company process
warranty claims or contact you with the latest
service information. All claims meeting
requirements during the limited warranty
period will be honored, whether or not the
product registration card is returned. Keep a
proof of purchase if you do not register your
unit.
Customer Note: If the dealer does not
register your product, please fill out, sign, and
return the product registration card to Ariens
or go to www.ariens.com.
EN - 2
UNAUTHORIZED REPLACEMENT
PARTS
Use only Ariens replacement parts. The
replacement of any part on this vehicle with
anything other than an Ariens authorized
replacement part may adversely affect the
performance, durability, or safety of this unit
and may void the warranty. Ariens disclaims
liability for any claims or damages, whether
warranty, property damage, personal injury or
death arising out of the use of unauthorized
replacement parts. To locate your nearest
Ariens Dealer, go to www.ariens.com on the
Internet.
DISCLAIMER
Ariens reserves the right to discontinue,
make changes to, and add improvements
upon its products at any time without public
notice or obligation. The descriptions and
specifications contained in this manual were
in effect at printing. Equipment described
within this manual may be optional. Some
illustrations may not be applicable to your
unit.
DELIVERY
Customer Note: If you have purchased this
product without complete assembly and
instruction by your retailer, it is your
responsibility to:
1. Read and understand all assembly
instructions in this manual. If you do not
understand or have difficulty following
the instructions, contact your nearest
Ariens Dealer for assistance. Make sure
all assembly has been properly
completed.
NOTICE: To locate your nearest Ariens
Dealer, go to www.ariens.com on the Internet.
WARNING: Improper assembly or
adjustments can cause serious
injury.
2. Understand all Safety Precautions
provided in the manuals.
3. Review control functions and operation
of the unit. Do not operate the Sno-Thro
unless all controls function as described
in this manual.
4. Review recommended lubrication,
maintenance and adjustments.
5. R eview Limited Warranty Policy.
6. Fill out a Product Registration Card and
return the card to the Ariens Company or
go to www.ariens.com.
EN - 3
SAFETY
Figure 2
1
3
2
WARNING: To avoid injury to hands
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Hand contact with the rotating
impeller is the most common cause
of injury associated with snow
throwers. Never use your hand to
clean out the discharge chute.
Keep hands and feet away from
auger and impeller.
SAFETY ALERTS
Look for these symbols to point
out important safety
precautions. They mean:
Attention!
Personal Safety Is
Involved!
Become Alert!
Obey The Message!
The safety alert symbols above and signal
words below are used on decals and in this
manual. Read and understand all safety
messages.
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death or
serious injury.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in death
or serious injury.
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor or
moderate injury. It may also be used
to alert against unsafe practices.
NOTATIONS
NOTICE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to
unit or attachment.
PRACTICES AND LAWS
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area. Always follow the practices
set forth in this manu a l .
REQUIRED OPERATOR TRAINING
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser; loaned, rented or sold,
ALWAYS provide this manual and any
needed safety training before operation.
SAFETY DECALS AND LOCATIONS
ALW AYS replace missing or damaged Safety
Decals. Refer to Figure 2 below for Safety
Decal locations.
EN - 4
1. DANGER!
2. DANGER!
Danger!
ONLY use clean-out tool to
clear blockages. NEVER
use your hands.
Never direct discharge
towards persons or
property that may be
injured or damaged by
thrown objects.
Keep people away from
unit while operating. Keep
children out of work area
and under watchful care of
a responsible adult.
Stop engine, remove key,
read manual before
making any repairs or
adjustments.
Read Owner/Operator
Manual.
Wear appropriate hearing
protection.
3. DANGER!
Danger!
ROTATING PARTS! ONLY
use clean-out tool to clear
blockages. NEVER use
your hands. High speed
impeller rotates below
discharge opening. Wait
for all moving parts to
stop before removing
clogs or servicing.
Danger!
ROTATING PARTS.
Keep clear of auger while
engine is running.
• Read Operator’s
Manual.
• Allow operation only by
properly trained adult,
never children.
• Stop engine and
remove ignition key
prior to leaving the
operator’s position for
any reason.
• Keep all controls,
guards and safety
devices properly
serviced and functional.
• Never direct discharge
towards persons or
property that may be
injured or damaged by
thrown objects.
EN - 5
EMISSION CONTROL SYSTEM
This equipment and/or its engine may include
exhaust and evaporative emissions control
system components required to meet U.S.
Environmental Protection Agency (EPA)
and/or California Air Resources Board
(CARB) regulations. T ampering with emission
controls and components by unauthorized
personnel may result in severe fines or
penalties. Emission controls and components
can only be adjusted by an Ariens Company
dealer or an authorized engine
manufacturer's service center. Contact your
Ariens Company Equipment Retailer
concerning emission controls and component
questions.
SAFETY RULES
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly or operating. Failure to
follow instructions could result in personal
injury and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly, maintenance or
service. Unintentional engine start up can
cause death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals
ALWAYS check overhead and side
clearances carefully before operation.
ALWA YS be aware of traffic when operating
along streets or curbs.
Keep children and people away. Keep
children out of work area and under watchful
care of a responsible adult.
NEVER allow children to operate or play on
or near unit. Be alert and shut off unit if
children enter area.
DO NOT allow adults to operate unit without
proper training. Only trained adults may
operate unit. Training includes actual
operation.
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards.
DO NOT operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Falling snow, fog, etc. can reduce vision and
cause an accident. Operate unit only when
there is good visibility and light.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
NEVER allow anyone to operate this unit
when their alertness or coordination is
impaired.
DO NOT operate unit without wearing
adequate winter outer garments. Wear
adequate safety gear, including safety
glasses with side shields, and protective
gloves. Wear proper footwear to improve
footing on slippery surfaces.
DO NOT wear loose clothing or jewelry and
tie back hair that may get caught in rotating
parts.
Protect eyes, face and head from objects that
may be thrown from unit. Wear appropriate
hearing protection.
Avoid sharp edges. Sharp edges can cut.
Moving parts can cut off fingers or a hand.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands away from all pinch
points.
DO NOT touch unit parts which might be hot
from operation. Allow parts to cool before
attempting to maintain, adjust or service.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on
gravel surfaces. Stay alert for hidden hazards
or traffic. Adjust Skid Shoes so Scraper Blade
does not contact gravel.
DO NOT throw snow any higher than
necessary.
Deflected materials can cause injury and
property damage.
Always stand clear of the discharge area
when operating this unit.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS disengage attachment, stop unit
and engine, remove key and allow moving
parts to stop before leaving operator’s
position.
ROTATING AUGER CAN CAUSE SERIOUS
INJURY. NEVER ATTEMPT TO UNCLOG
OR CLEAN UNIT WHILE ENGINE IS
RUNNING.
EN - 6
Read, understand, and follow all instructions
in the manual and on the machine before
starting.
Understand:
• How to operate all controls.
• The functions of all controls.
• How to STOP in an emergency.
Before starting engine, disengage control(s).
Use only approved extension cords and
receptacles when starting units equipped with
electric starter. DO NOT connect electric
starter cord to any wiring system that is not a
three-wire grounded system.
ALWAYS allow unit and engine to adjust to
outdoor temperatures before clearing snow.
DO NOT overload the machine capacity by
attempting to operate or to clear snow at too
fast a rate.
Slow down and turn corners slowly.
Do not operate in reverse unless absolutely
necessary. ALWAYS back up slowly. Always
look down and behind before and while
backing.
Disengage attachment drive when traveling
from one work area to another.
Abnormal Vibrations are a warning of trouble.
Striking a foreign object can damage unit.
Immediately stop unit and engine. Remove
key and wait for all moving parts to stop.
Remove wire from spark plug. Inspect unit
and make any necessary repairs before
restart.
Before cleaning, removing clogs or making
any inspections, repairs, etc.: disengage
clutch(es), stop unit and engine, remove key,
allow moving parts to stop. Allow hot parts to
cool.
Run unit a few minutes after clearing snow to
prevent freeze-up of attachment.
Disengage attachment when not in use.
Disengage all clutches before starting engine.
Adjust skid shoes to clear gravel or crushed
rock surfaces safely.
Never leave a running unit unattended.
ALWAYS shut off engine before leaving unit.
ALW A YS remove key to prevent unauthorized
use.
Never carry passengers.
Check clutch and brake operation frequently.
Adjust and service as required. All motion of
drive wheels and auger/impeller must stop
quickly when control levers are released.
DO NOT operate on steep slopes. DO NOT
clear snow across the face of slopes. Keep all
movement on slopes slow and gradual. DO
NOT make sudden changes in speed or
direction. Use a slow speed to avoid stops or
shifts on slopes. Avoid starting or stopping on
a slope.
DO NOT park unit on a slope unless
absolutely necessary. When parking on a
slope always block the wheels.
ALWAYS shut off engine, remove key, and
close fuel shut-off valve or drain fuel when
transporting unit on a truck or trailer.
Use extra care when loading or unloading
unit onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Keep unit free of ice or other debris. Clean up
oil or fuel spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use only an
approved gasoline container with an
appropriately sized dispensing spout.
NO smoking, NO sparks, NO flames.
ALWAYS allow engine to cool before
servicing.
NEVER fill fuel tank when engine is running
or hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up
spilled fuel.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel
it on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle lockopen device.
EN - 7
If fuel is spilled on clothing, change clothing
immediately.
Properly remove fuel before tipping unit up
onto housing, so no spills will occur.
Secure unit so it will not tip over during
maintenance.
ALWAYS keep protective structures, guards,
and panels in good repair, in place and
securely fastened. NEVER modify or remove
safety devices.
DO NOT change engine governor settings or
over-speed engine.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Keep all hardware properly tightened. Check
shear bolts frequently.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present such as hot water heaters, space
heaters, or clothes dryers. Allow the engine to
cool before storing in any enclosure.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
For extended storage, clean unit thoroughly.
See Engine Manual for proper storage.
Use only attachments or accessories
designed for your unit.
Check components frequently. If worn or
damaged, replace with manufacturer’s
recommended parts.
EN - 8
ASSEMBLY
Figure 3
9
8
10
2
3
1
7
14
13
12
11
6
4
5
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: Dropping or tipping over
boxed unit could result in personal
injury or damage to unit.
PACKAGE CONTENTS
Check the contents of your package for the
parts listed below (Figure 3):
Item Part No. Qty Description
The following parts are included as part of
the Sno-thro Unit:
N/A 1 Sno-thro Unit
1.
07028500 2 3/8 x 3/4" Hex Head
2.
The following parts (3 – 6) are included as a
part of the Lower Handlebar:
04584751 1 Lower Handlebar
3.
06221600 4 5/16 x 2-1/4" Round
4.
07500005 4 Handlebar Spacer
5.
06545400 4 5/16" Nyloc Flange
6.
N/A 1 Upper Handlebar
7.
N/A 1 Discharge Chute
8.
04507700 1 Chute Crank Rod
9.
10.
11.
12.
13.
14.
N/A 1 Literature Pack
02483859 2 Skid Shoe, Reversible
06212000 4
06435900 4
06529600 4
If any of the contents listed are missing
contact your local Ariens dealer. Use only
Ariens approved parts; unapproved parts
may void the unit warranty.
Serrated Flange
Grade 5 Bolt
Head Square Neck
Grade 5 Bolt
Nut
Assembly
Assembly With
Control
(Models 921029, 040)
Bolt, Round Head
Square Neck
3/8-16 x 1"
921029, 040)
(Models
Washer, Flat Steel
7/16 x 1 x 5/64"
(Models 921029, 040)
Nut, Locking, Center
3/8-16 (Models
921029, 040)
ASSEMBLY
To ols Requi re d
•Pliers
• Open-End Wrenches: 3/8, 7/16, 1/2,
9/16" and/or Adjustable Wrench
• Tire Gauge
• Torque Wrench (Optional)
• Phillips Screwdriver
EN - 9
Unfold Lower Handlebar
Figure 4
1
1. Lower Handlebar
2. Mounting Hole
2
(Right Wheel Not Shown)
Figure 5
3
4
2
1. Upper Handlebar Assembly
2. Lower Handlebar
3. 5/16 x 2-1/4" Round Head Square
Neck Grade 5 Bolt
4. Handlebar Spacer
5. 5/16" Nyloc Flange Nut
1
5
Figure 6
3
1. Clutch Arm
2. Cable Eyelet
3. Attachment Control Cable
4. Traction Control Cable
1
4
2
(Figure 4)
IMPORTANT: Be sure to block wheels or
secure unit so it does not move during
assembly.
1. Rotate lower handlebar out from unit so
lower handlebar mounting holes align
with mounting holes on the unit frame.
(Figure 4).
.
2. Secure lower handlebar to unit using two
3/8 x 3/4" hex head serrated flange
grade 5 bolts (Figure 3, Item 2).
3. Tighten all four bolts to 25 – 42 lbf-ft
(33.9 – 56.9 N•m).
Attach Upper Handlebar Assembly
(Figures 5 and 6)
1. Attach upper handlebar assembly to
lower handlebar using two sets of the
handlebar hardware. One set to attach
each side of the handlebars. (Figure 5).
NOTICE: DO NOT tighten hardware. Allow
upper handlebar assembly to hang from the
lower handlebars for the next step. (Figure 5).
.
2. Hook spring end of attachment control
cable to the clutch arm.
3. Hook spring end of the traction control
cable to the cable eyelet on back of
frame.
.
EN - 10
Unfold Upper Handlebar Assembly
Figure 7
1. Handlebar Hardware
2. Shift Rod Hardware
3. Shift Rod
4. Speed Selector Lever
1
3
2
4
Figure 8
2
4
3
1. Wire Harness
2. Cable Tie
3. Cable Anchor
4. Engine Electrical Plug
1
2
(Figure 7)
1. Rotate the handlebar into operating
position.
NOTICE: Be careful not to damage cable
spring hooks when rotating handlebar
upward.
.
2. Install the remaining handlebar
hardware attaching the upper handlebar
assembly to the lower handlebar
(Figure 5).
3. Tighten all hardware.
4. Remove packaging around shift rod.
5. Rotate shift rod into place and tighten
hardware.
6. C onnect shift rod to speed selector arm
and adjust as specified in Speed
Selector Adjustment on page 27.
7. Adjust attachment cable as specified in
Attachment Clutch/Brake Adjustment on
page 28.
8. Adjust the traction cable as specified in
Traction Drive Clutch Adjustment on
page 30.
Connect Headlight Wire Harness
(Figure 8)
NOTICE: The headlight wire harness comes
attached to the upper handlebar assembly.
1. Route the wire harness along the interior
of the right side handlebar.
2. Connect to the engine electrical plug.
3. Press cable anchor into mounting hole in
the frame near the engine electrical
plug.
4. Secure the wire harness to the
handlebars using the cable ties attached
to the wire harness.
5. Gather excess wire harness length and
fasten to handlebar with cable tie
included in literature pack.
Install Discharge Chute, Chute
Control and Chute Rod
(Figures 9, 10, 11 and 12)
1. Grease underside of discharge chute
ring (if not already greased).
2. Remove mounting hardware from auger
housing. (Figure 9).
3. Install discharge chute over opening in
the auger housing. Put J-clamp from
deflector cable on top mounting bolt.
4. Install mounting hardware into housing
and finger tighten.
NOTICE: Leave discharge chute pedestal
loose to help install the chute rod.
EN - 11
10. Remove hairpin from pin on chute
1
5
3
2
4
Figure 9
1. Mounting Holes
2. Discharge Chute
3. Chute Pedestal
4. Discharge Chute Ring
5. Mounting Hardware
6. J-Clamp
6
Figure 10
1. Chute Control Assembly
2. Nylon Bushing
3. Hex Hub
4. E-Clip
5. Control Mount Bracket
6. Control Panel
7. Rubber Grommet
8. Quick Turn Chute Control
9. Chute Lock Cable
1
1
3
4
2
6
5
7
8
9
control, install cable eyelet onto pin and
re-install hairpin. See Figure 11.
5. Remove the gear cover from top of
chute pedestal. (Figure 12).
6. Re lease the lock arm on the gear
assembly with your finger and rotate the
discharge chute so it points straight
ahead.
NOTICE: Make sure alignment markers on
gear assembly are lined up when discharge
chute is pointing straight ahead.
7. Remove chute control assembly from
chute lock cable.
8. Insert chute control assembly into slot in
control panel from below and insert
assembly into nylon bushing in control
mount bracket. Fasten connection with
E-clip. See Figure 10.
9. Insert chute lock cable through hole in
front of dash panel. Feed cable eyelet
and rubber seal through hole in chute
control assembly and snap cable end
into control assembly. Slide rubber seal
over cable end to prevent moisture from
entering the cable.
EN - 12
Loading...