Ariens A20BH42 (96046001100), 96046001100, 93604200, 936042 Owner’s Manual

YDRO TRACTO

Operator Manual

Models

936042 42" Hydro Tractor

__ _ ENGL,SH

431471 Rev. 2 04.08.10

Printed in USA

Safe Operation Practices for Ride=On Mowers

DANGER: THiS CUTTING MACHINE iS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY iNSTRUCTiONS COULD RESULT iN SERIOUS iNJURY OR DEATH.

WARNING: in orderto prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.

WARNING: Do not coast down ahill in neu-tral, you may lose control of the tractor.

WARNING: Tow onlythe attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only atthe lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

WARNING

Engine exhaust, some of itsconstituents, and certain vehicle components contain or emit chemicals

known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING

Battery posts, terminals and related accessories contain leadand lead compounds, chemicals known

to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands

after handling.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the

machine and in the manual before starting.

• Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at

all times.

• Only allow responsible adults, who are familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.

• Ensure the area is clear of bystanders before operating. Stop machine if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while backing.

• Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.

• Do not operate machine without the entire grass catcher, discharge chute, or other safety devices in place and

working.

SAFETY RULES

• Slow down before turning.

• Never leave a running machine unattended. Always

turn off blades, set parking brake, stop engine, and remove keys before dismounting.

• Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or

unclogging the discharge chute.

• Operate machine only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading orunloading the machine into a trailer or truck.

• Always wear eye protection when operating machine.

• Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower- related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

• Follow the manufacturer's recommendation for wheel weights or counterweights.

• Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil orfuel spillage before operating orstoring the machine. Allow machine to cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or

death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it,

do not mow it.

• Mow up and down slopes, not across.

• Watch for holes, ruts, bumps, rocks, or other hidden

objects. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

• Choose a low ground speed so that you will not have to stop or shift while on the slope.

• Do not mow on wet grass. Tires may lose traction. Always keep the machine in gear when going down

slopes. Do not shift to neutral and coast downhill.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed

slowly straight down the slope.

• Keep all movement on the slopes slow and gradual.

Do not make sudden changes in speed or direction,

which could cause the machine to roll over.

• Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine. Do no use on steep slopes.

• Do not try to stabilize the machine by putting your foot on the ground.

• Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over

the edge or if the edge caves in.

Safe Operation Practices for Ride=On Mowers

SAFETY RULES &

ill. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keepchildrenoutofthemowingareaandinthewatchful care of a responsible adult other than the operator.

• Be alert and turn machine off if a child enters the

area,

• Before and while backing, look behind and down for small children.

• Never carry children, even withthe blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the machine.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may block your view of a child.

IV. TOWING

• Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the

hitch point.

• Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes.

• Never allow children or others in or on towed equipment.

• On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

• Travel slowly and allow extra distance to stop.

V. SERVICE

SAFE HANDLING OF GASOLINE To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

• Use only approved gasoline container.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel container where there isan open flame, spark, orpilot light such as on a water

heater or other appliances.

• Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers

on the ground away from your vehicle when filling.

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle incontact with the rim of the fuel tank or container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immedi- ately.

• Never overfill fuel tank. Replace gas cap and tighten securely.

GENERAL SERVICE

• Never operate machine in a closed area.

• Keep all nuts and bolts tight to ensure the equipment is in safe working condition.

• Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris

build-up. Clean oil or fuel spillage and remove any fuel- soaked debris. Allow machine to cool before storing.

• If you strike a foreign object, stop and inspect the machine. Repair, if necessary, before restarting.

• Never make any adjustments or repairs with the engine running.

• Check grass catcher components and the discharge chute frequently and replace with manufacturer's rec- ommended parts, when necessary.

• Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. Check brake operation frequently. Adjust and service as required.

Maintain or replace safety and instruction labels, as necessary.

Ensure the area is clear of bystanders before operat- ing. Stop machine ifanyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary. Always look down and behind before and while back- ing.

Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the machine.

Keep children out ofthe mowing area and inthewatchful care of a responsible adult other than the operator.

Be alert and turn machine off if a child enters the area.

Before and while backing, look behind and down for small children.

Mow up and down slopes (15° Max), not across. Choose a low ground speed so that you will not have

to stop or shift while on the slope. Avoid starting, stopping, or turning on a slope. If the

tires lose traction, disengage the blades and proceed slowly straight down the slope.

If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.

Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

PRODUCT SPECiFiCATiONS

Gasoline Capacity 3.00 Gallons And Type: Unleaded Regular

Oil Type (Api-Sg-SI): SAE 30 (Above 32°F) o Oil Capacity: W/Filter: 64 Oz.

Spark Plug: Champion QC12YC

Ground Speed (Mph): Forward: 5.2

Charging System: 3 Amps Battery

Battery: AMP/HR: 28

Blade Torque: 45-55 Ft. Lbs. (62-75 Nm)

SAE 5W-30 (Below 32 F) W/O Filter: 60 Oz.

(Gap: .040") Reverse: 2.9

5 Amps Headlights MIN. CCA: 230

Case Size: U1R

CONGRATULATIONS on your purchase of anew tractor.

Ithas been designed, engineered and manufactured to give

you the best possible dependability and performance. Should you experience any problem you can not easily rem-

edy, please contact your nearest authorized service center/ department. We have competent, well-trained technicians

and the proper tools to service or repair this tractor.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your tractor properly. Always observe the "SAFETY RULES".

CUSTOMER RESPONSIBILITIES

Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and using your tractor.

• Follow the instructions under "Maintenance" and "Stor- age" sections of this manual.

WARNING: This tractor is equipped with an internal com- bustion engine and should not be used on or near any un-

improved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system isequipped with a spark arrester meeting applicable local or state laws (if

any). If a spark arrester is used, itshould be maintained in effective working order by the operator.

A spark arrester for the muffler is available through your nearest authorized service center/department.

In the state of California the above is required by law (Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on federal lands.

TABLE F CONTENTS

SAFETY RULES ......................................................... 2=3

PRODUCT SPECIFICATIONS ....................................... 4

CUSTOMER RESPONSIBILITIES ................................. 4

ASSEMBLY ................................................................. 6=7

OPERATION ............................................................. 8=14

MAINTENANCE SCHEDULE ...................................... 15

MAINTENANCE ..................................................... 15-18

SERVICE AND ADJUSTMENTS ............................ 19=25

STORAGE .................................................................... 26

TROUBLESHOOTING ............................................ 27=28

WARRANTY ............................................................ 30-31

UNASSEMBLED PARTS

Steering Wheel

i J

Steering

Wheel Insert

Steering

Wheel

/1 \ _t

i-- __i I /

[ [ '.

Steering Wheel "'J--"

Adapter

I /

/ /

Steering Boot

(1) Large

Flat Washer

(1) Hex Bolt

(1) Lock

Washer

Steering Extension

Shaft

(1) Seat

Key(s)

Seat

(1) Washer

(1) Bolt

Slope Sheet

(1) Oil Drain Tube For Future Use

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 5/16" wrench Utility knife (2) 7/16" wrenches Tire pressure gauge (2) 1/2" wrenches Pliers (1) 9/16" wrench

When right or lefthand ismentioned inthis manual, itmeans when you are in the operating position (seated behind the

steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

• Remove all accessible loose parts and parts cartons from carton.

• Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

• Check for any additional loose parts or cartons and remove.

INSTALL STEERING WHEEL

• Position front wheels of the tractor so they are pointing straight forward.

• Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

• Position steering wheel so cross bars are horizontal

(left to right) and slide inside boot and onto adapter.

• Assemble large flat washer, lock washer, hex bolt and tighten securely.

• Snap steering wheel insert into center ofsteeringwheel.

• Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

• Lift seat to raised position. NOTE: If this battery is put into service after month and

year indicated on label (label islocated between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual

for charging instructions.)

• For battery and battery cable installation see "RE- PLACING BATTERY" in the Service and Adjustments

section in this manual.

LABEL

Fig. 1

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

• Slide extension shaft onto lower steering shaft.

• Place tabs of steering boot over tab slots in dash and push down to secure.

STEERING WHEEL

ADAPTER

TABS

EXTENSION

TAB

LOWER SHAFT

Fig, 2

INSTALL SEAT (See Fig. 3 and 4)

• Remove bolt and flat washer securing seat tocardboard packing and set aside for assembly of seat to tractor.

Remove the cardboard packing and discard.

• Connect switch to seat.

• Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

• Push down on seat to engage pads in slots and pull seat towards rear of tractor.

• Raise seat and tighten bolt securely.

ASSEMBLY

SEAT /

SWITCH

PAD _

SLOT [

F-_

TAPE

WiRiNG HARNESS

Fig. 3

Remove tape and discard.

Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating

position is not comfortable, adjust seat.

TO ADJUST SEAT (See Fig. 4)

• Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT TAPE

FLAT WASHER

SEAT PAN

BO_ TAB ADJUSTMENT

HANDLE

Fig. 4

NOTE: You may now rollyour tractor off the skid. Follow the instructions below to remove the tractor from the skid.

_i_ WARNING: Before starting, read, understand and fol-

low all instructions in the Operation section of this manual. Ensure tractor is in a well-ventilated area. Ensure the area

in front of tractor is clear of other people and objects.

TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls)

• Raise attachment lift lever to its highest position.

• Release parking brake bydepressing clutch/brake pedal.

• Place freewheel control in "transmission disengaged" position (See "TO TRANSPORT" in the Operation section of this manual).

• Roll tractor forward off skid.

• Remove banding holding the deflector shield up against tractor.

Continue with the instructions that follow.

CHECK TiRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important

for best cutting performance.

• Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be prop- erly leveled. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF BELTS

See the figures that are shown for replacing motion and mower blade drive belts inthe Service andAdjustments sec-

tion of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See "TO CHECK BRAKE"

in the Service and Adjustments section of this manual.

'CHECKLiST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BES T PERFORMANCE

AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

J" All assembly instructions have been completed. J" No remaining loose parts in carton.

Battery is properly prepared and charged.

J" Seat is adjusted comfortably and tightened securely. J" All tires are properly inflated. (For shipping purposes,

the tires were overinflated at the factory).

J" Ensure mower deck is properly leveled side-to-side/

front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

J" Check mower and drive belts. Ensure they are routed

properly around pulleys and inside all belt keepers.

J" Check wiring. See that all connections are still secure

and wires are properly clamped.

J" Before driving tractor, Ensure freewheel control is in

"transmission engaged" position (see "TO TRANS- PORT" in the Operation section of this manual).

WHILE LEARNING HOWTO USE YOUR TRACTOR, PAYEXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

J" Engine oil is at proper level. J" Fuel tank is filled with fresh, clean, regular unleaded

gasoline.

J" Become familiar with all controls, their location and

function. Operate them before you start the engine. J" Ensure brake system is in safe operating condition. J" Ensure Operator Presence System and Reverse Op-

eration System (ROS) are working properly (See the

Operation and Maintenance sections in this manual). J" It is importantto purge the transmission before operat-

ing your tractor for the first time. Follow proper start-

ing and transmission purging instructions (See "TO

START ENGINE" and "PURGE TRANSMISSION" in

the Operation section of this manual).

OPERATION

These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.

L I\1

REVERSE NEUTRAL HiGH

ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE PARKING BRAKE PARKING BRAKE

OPERATION LOCKED UNLOCKED

SYSTEM (ROS)

LOW CHOKE FAST SLOW

iGNiTiON SWITCH

OVER TEMP

LIGHT

FUEL OiL PRESSURE BATTERY

REVERSE FORWARD MOWER HEIGHT

MOWER LiFT

ATTACHMENT ATTACHMENT

CLUTCH DISENGAGED CLUTCH ENGAGED

LIGHTS ON

FREE WHEEL

(Automatic Models only)

Failure to follow instructions

could result in serious injury or death. The safety alert symbol

is used to identify safety inform-

ation about hazards which can

result in death, serious injury

and/or property damage.

DANGER, KEEP HANDS

AND FEET AWAY

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION indicates a hazard which, if not avoided,

might result in minor or moderate injury.

CAUTION when used without the alert symbol,

indicates a situation that could result in damage

to the tractor and/or engine.

NOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury

and/or property damage.

FIRE indicates a hazard which, if not avoided,

could result in death, serious injury and/or

property damage.

KEEP AREA CLEAR SLOPE HAZARDS

(SEE SAFETY RULES SECTION)

OPERATION

KNOW YOUR TRACTOR

READ THiS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR

Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Our tractors conform to the applicable safety standards of the American National Standards Institute.

(A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.

(B) BRAKE PEDAL - Used for braking the tractor and starting the engine.

(D) THROTTLE/CHOKE CONTROL - Used for starting and controlling engine speed.

(E) ATTACHMENT CLUTCH LEVER -Used to engage the mowerblades, orother attachmentsmountedtoyour tractor.

03104

Fig. 5

(F) IGNITION SWITCH - Used for starting and stopping

the engine. (G) REVERSE OPERATION SYSTEM (ROS) "ON"

POSITION -Allows operation of mower or other powered attachment while in reverse.

(H) LIGHT SWITCH - Turns the headlights on and off. (J) MOTION CONTROL LEVER - Selects the speed and

direction of the tractor. (M) FREEWHEEL CONTROL - Disengages transmission

for pushing or slowly towing the tractor with the engine off.

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating

your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 6)

Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the

operator to leave the seat without first setting the parking brake will shut off the engine.

• Depress clutch/brake pedal (B) into full "BRAKE" posi- tion and hold.

• Place parking brake lever (C) in "ENGAGED" position and release pressure from clutch/brake pedal. Pedal

should remain in "BRAKE" position. Ensure parking brake will hold tractor securely.

Fig. 6

STOPPING (See Fig. 7)

MOWER BLADES

• To stop mower blades, place attachment clutch control in the "DISENGAGED" position (r_).

• Never use the choke to stop the engine.

iMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO DISCHARGE AND GO DEAD.

NOTE: Under certain conditions when tractor is standing idlewith the engine running, hot engine exhaust gases may

cause "browning" of grass. To eliminate this possibility, al- ways stop engine when stopping tractor on grass areas.

pletely, as described above, and set CAUTION: Always stop tractor corn=

parking brake before leaving the opera= tot's position.

TO USE THROTTLE CONTROL (D) (See Fig. 8)

Always operate engine at full speed (fast).

• Operating engine at less than full speed (fast) reduces the engine's operating efficiency.

• Full speed (fast) offers the best mower performance.

(_il) ATTACHMENT (IJ_) ATTACHMENT

CLUTCH SWITCH CLUTCH SWITCH

"DISENGAGED .... ENGAGED"

Fig. 7

GROUND DRIVE

• To stop ground drive, depress brake pedal all the way down.

• Move motion control lever (J) to neutral position.

ENGINE

• Move throttle control (D) between half and full speed (fast) position.

NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause engine

to "backfire".

• Turn ignition key (F) to "STOP" position and remove key.Always remove key when leaving tractor to prevent

unauthorized use.

Fig. 8

TO MOVE FORWARD AND BACKWARD

(See Fig. 9)

The direction and speed of movement is controlled by the motion control lever. (J)

Fig. 9

• Start tractor with motion control lever in neutral position.

• Release parking brake.

• Slowly move motion control lever to desired position.

OPERATION

TO ADJUST MOWER CUTTING HEIGHT

(See Fig. 10)

The position of the attachment lift lever (A) determines the cutting height.

Fig. 10

• Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The

heights are measured from the ground to the blade tip with the engine not running. These heights are approximate

and may vary depending upon soil conditions, height of grass and types of grass being mowed.

• The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot

months. For healthier and better looking lawns, mow often and after moderate growth.

• For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively

high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with

the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally

positioned inthe seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough,

rolling terrain or hills.

• Select desired height of cut with attachment lift lever.

• Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector

shield (S) in place (See Fig. 12).

TO ADJUST GAUGE WHEELS (See Fig. 11)

Gauge wheels are properly adjusted when they are slightly off the ground when mower isat the desired cutting height

in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain

conditions. NOTE:Adjust gauge wheels with tractor on a flat level

surface.

• Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in the Operation

section of this manual).

• With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole as shown and tighten securely.

• Repeat for opposite side installing gauge wheel insame adjustment hole.

Fig. 11

Fig. 12

TO OPERATE ON HILLS

= m

I CAUTION: Do not drive up or down hills i

with slopes greater than 15° and do not

drive across any slope.

• Choose the slowest speed before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If slowing is necessary, move throttle control lever to slower position.

• If stopping is absolutely necessary, push clutch/brake pedal quicklyto brake position and engage parking brake.

• Move motion control lever to neutral position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURNTO NEUTRALPOSITIONWHENTHE BRAKEPEDAL IS DEPRESSED.

Torestart movement, slowly release parking brake and clutch/brake pedal.

Slowly move motion control lever to slowest setting. Make all turns slowly.

02940

OPERATION

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse

direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON"

position. _WARNING: Backing up with the attachment clutch en-

gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator

decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless

absolutely necessary.

USINGTHE REVERSE OPERATION SYSTEM (See Fig. 13) Only use ifyou are certain no children or other bystanders

will enter the mowing area.

• Move motion control lever to neutral (N) position.

• With engine running, turn ignition key counterclockwise

to ROS "ON" position.

• Look down and behind before and while backing.

• Slowly move motion control lever to reverse (R) posi-

tion to start movement.

• When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

• Pull freewheel control out and into the slot and release so it is held in the disengaged position.

• Do not push or tow tractor at more than two (2) MPH.

• To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, ensure hood is closed and secured to tractor. Use an appropriate means of tying

hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTH ER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications ofthe manufacturer of your trac-

tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with

the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the fac- tory, already filled with summer weight oil.

• Check engine oil with tractor on level ground.

• Remove oil fill cap/dipstick and wipe clean, reinsert the

dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until

"FULL' mark on dipstick is reached. Do not overfill.

• For cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the

Maintenance section of this manual).

• To change engine oil, see the Maintenance section in this manual.

ROS "ON" POSITION

Fig. 13

ENGINE "ON" POSITION (NORMAL OPERATING)

TO TRANSPORT (See Fig. 14)

When pushing or towing your tractor, ensure to disengage transmission by placing freewheel control in freewheeling

position. Free wheel control islocated at the rear drawbar of tractor.

• Raise attachment lift to highest position with attachment lift control.

TRANSMiSSiON ENGAGED

TRANSMiSSiON DISENGAGED

ADD GASOLINE

Fillfuel tank to bottom of filler neck. Do not overfill. Use

fresh, clean, regular unleaded gasolinewith a minimum of 87 octane. (Use of leaded gasoline will increase

carbon and lead oxide deposits and reduce valve life).

Do not mix oil with gasoline. Purchase fuel inquantities

that can be used within 30 days to ensure fuel freshness.

fuel. Do not store, spill or use gasoline near an open flame.

iMPORTANT:WHENOPERATINGINTEMPERATURESBELOW 32°F, USE FRESH, CLEAN WINTER GRADE GASOLINE TO

HELP ENSURE GOOD COLD WEATHERSTARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damagethe fuel sys= tern of an engine while in storage. To avoid engine

problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and

carburetor are empty. Use fresh fuel next season. See Storage instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Fig. 14

OPERATION

TO START ENGINE (See Fig. 4)

When starting the engine for the first time or ifthe engine has run out of fuel, it will take extra cranking time to move

fuel from the tank to the engine.

• Ensure freewheel control is inthe transmission engaged position.

• Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

• Place motion control lever in neutral position.

• Move attachment clutch to "DISENGAGED" position.

• Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

• Insert key into ignition and turn key clockwise to "START" position and release key as soon as engine starts.

Do not run starter continuously for more than fifteen

seconds per minute. If the engine does not start after several attempts, move throttle control to fast position,

wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke

position and retry.

WARM WEATHER STARTING (50°F/10°C and above)

• When engine starts, move the throttle control to the fast position.

• The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine

and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50°F/10°C and below)

• When engine starts, allow engine to run with the throttle control inthe choke position until theengine runs roughly, then move throttle control to fast position. This may

require anengine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

• Before driving the unit in cold weather, the transmission should be warmed up as follows:

• Ensure the tractor is on level ground.

• Place the motion control lever in neutral. Release the parking brake and let the clutch/brake

slowly return to operating position.

• Allow one minute for transmission to warm up. This

can be done during the engine warm up period.

• The attachments can also be used during the engine warm-up period afterthe transmission has been warmed

up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 °F/0°C) the carburetor fuel mixture

may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and

Adjustments section of this manual.

PURGE TRANSMISSION

i _ CAUTION: Never engage or disengage] To ensure proper operation and performance, it is recom-

mended that the transmission be purged before operating tractor for the first time. This procedure will remove any

trapped air inside the transmission which may have devel- oped during shipping of your tractor.

iMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD

BE PURGEDAFTER REINSTALLATIONBEFOREOPERATING THE TRACTOR.

1. Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

2. Disengage transmission by placing freewheel control in freewheeling position (See "TO TRANSPORT" in this section of manual).

3. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

i _ CAUTION: Atanytime, duringstep4,there i

4. Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse

position and hold for five (5) seconds. Repeat this procedure three (3) times.

5. Move motion control lever to neutral position. Shut- off engine and set parking brake.

6. Engage transmission by placing freewheel control in engaged position (See "TO TRANSPORT" in this sec- tion of manual).

7. Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral position, slowly disengage clutch/brake pedal.

8. Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the motion control lever to the neutral position. Repeat this proce- dure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

freewheel lever whilethe engine is running.

may be movement of the drive wheels.

OPERATION

MOWING TIPS

• Tire chains cannot be used when the mower housing

is attached to tractor.

• Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in

the Service and Adjustments section of this manual.

• The left hand side of mower should be used for trimming.

• Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of

the tractor. This will result in a more even distribution of clippings and more uniform cutting.

• When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 15).

(

Fig. 15

• If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

• Do not mow grass when it iswet. Wet grass will plug mower and leave undesirable clumps. Allow grass to

dry before mowing.

• Always operate engine at full throttle when mow- ing to assure better mowing performance and proper

discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

MAINTENANCE

SCHEDULE

Check Brake Operation

BEFORE

EACH

USE

CheckTire Pressure

T Check Operator Presence & ROS Systems A Checkfor Loose Fasteners

C Check/Replace Mower Blades

T Lubrication Chart

0 Check Battery Level

R Clean Battery andTerminals

Clean Debris Off Steering Plate CheckTransaxle Cooling Check Mower Levelness CheckV-Belts

Check Engine Oil Level Change Enqine Oil (with oil filter) Change Engine Oil (without oil filter)

E Clean Air Filter

G Clean Air Screen

I Inspect Muffler/Spark Attester

N Replace Oil Filter (if equipped)

E Clean Engine Cooling Fins

Replace Spark Plug Replace Air Filter Paper Cartridge

m R_lace Fuel Filter

1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions.

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tractor

as instructed in this manual. Some adjustments will need to be made periodically to

properly maintain your tractor. At least once a season, check to see if you should make

any of the adjustments described in the Service and Adjustments section of this manual.

• At least once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.

EVERY

HOURS

EVERY

HOURS

EVERY

HOURS

EVERY

100

HOURS

EVERY

SEASON

BEFORE

STORAGE

v" v'

_1,2

V"2

V'2

_,2

v"2

_,,,,,..,=,,=====.,=_

3 - Replace blades more often when mowing in sandy soil. 5 - See Cleaning in Maintenance Section. 4 - Not required if equipped with maintenance-free battery.

LUBRICATION CHART

(_ SPINDLE ZERK, SPINDLE ZERK

(_FRONT FRONT

WHEEL WHEEL

BEARING BEARING

ZERK ZERK

SECTOR GEAR

TEETH

ENGINE

BEFORE EACH USE

Check engine oil level.

• Check brake operation. Check tire pressure.

• Check operator presence and ROS systems for proper operation.

Check for loose fasteners.

01965

(_ General Purpose Grease (_ Refer to Maintenance "ENGINE" Section

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OFTHE SELF-LUBRICATING BEARINGS. IFYOU FEELTHEY MUST BE LUBRICATED, USE ONLYA DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest

speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See "TO CHECK BRAKE" in the Service and Adjustments

section of this manual).

TIRES

• Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your

local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 16)

Ensure operator presence and reverse operation systems are working properly. If your tractor does not function as

described, repair the problem immediately.

• The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any attempt bythe operator to leave the seat without first setting the parking brake should shut off the engine.

• When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

• The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

• When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch

engaged, any attempt by the operator to shift into reverse should shut off the engine.

• When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION (NORMAL OPERATING)

Fig. 16

BLADE CARE

Forbest results mower blades must be kept sharp. Replace

bent or damaged blades.

proved bythe manufacturer of your tractor.

_ AUTION: Use onlya replacement blade ap=

Using a blade not approved by the manu= facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 17)

• Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

• Remove blade bolt by turning counterclockwise.

• Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

iMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

• Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

iMPORTANT: SPECIAL BLADE BOLTIS HEATTREATED.

BLADE BOLT

(SPECIAL)

CENTER HOLE

Fig. 17

BATTERY

Your tractor has abattery charging system which issufficient for normal use. However, periodic charging of the battery

with an automotive charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• Keep small vent holes open.

• Recharge at 6-10 amperes for I hour.

NOTE: The original equipment battery on your tractor ismain- tenance free. Do not attempt to open or remove caps or cov-

ers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause

the battery to "leak" power.

• Raise seat.

• Disconnect BLACK battery cable first then RED bat-

tery cable and remove battery from tractor.

• Rinse the battery with plain water and dry.

• Clean terminals and battery cable ends with wire brush

until bright.

• Coat terminals with grease or petroleum jelly.

• Reinstall battery (See "REPLACING BATTERY" in

the Service and Adjustments section of this manual).

MAINTENANCE

V=BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not

adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE MAINTENANCE

The transmission fan and cooling fins should be kept clean to assure proper cooling.

Do not attempt to clean fan or transmission while engine

is running or while the transmission is hot. To prevent pos- sible damage to seals, do not use high pressure water or

steam to clean transmission.

Inspect cooling fan to ensure fan blades are intact and

clean.

Inspect cooling fins for dirt, grass clippings and other

materials. To prevent damage toseals, do not use com- pressed airor high pressure sprayer toclean coolingfins.

TRANSAXLE PUMP FLUID

The transaxle was sealed at the factory and fluid mainte- nance is not required for the life of the transaxle. Should

the transaxle ever leak or require servicing, contact your nearest authorized service center/department.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

SAE VISCOSITY GRADES

OIL DRAIN VALVE

CLOSED AND ----_._ __Z_L-/_'_ -'_'\

LOCKED _"-['_-__ POSITION __._

DRA N

YELLOW CAP _I--_ _,__ TUBE

Fig. 18

* Unlock drain valve by pushing inward and turning

counterclockwise.

* To open, pull out on the drain valve. * After oil has drained completely, close and lock the

drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

* Remove the drain tube and replace the cap onto to the

bottom fitting of the drain valve.

* Refill engine with oil through oil fill dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see "PRODUCT SPECl FICATIONS" section ofthis manual.

* Use gauge on oil fill cap/dipstick for checking level.

Ensure dipstick cap is tightened securely for accurate reading. Keep oil at "FULL' line on dipstick. Tighten cap onto the tube securely when finished.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change ifthe tractor is used more than 100 hours inone year.

AIR FILTER

Your engine will not run properly using a dirty air filter. Ser- vice air cleaner more often under dusty conditions.

F -20 0 30 32 40 60 80 100 C -30 -2; -1; ; 1'0 20 30 4;

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result inincreased

oil consumption when used above 32°F/0°C. Check your engine oil level more frequently to avoid possible engine

damage from running low on oil. Change the oil after every 50 hours of operation or at least

once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine

and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 18)

Determine temperature range expected before oil change.

All oil must meet API service classification SG-SL.. * Ensure tractor is on level surface.

* Oil will drain more freely when warm. * Catch oil in a suitable container.

* Remove oil fill cap/dipstick. Be careful not to allow dirt

to enter the engine when changing oil.

* Remove yellow cap from end of drain valve and install

the drain tube onto the fitting.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with awire brush or

compressed airto remove dirt and stubborn dried gum fibers.

ENGINE COOLING SYSTEM

To ensure proper cooling, ensure the grass screen, cool- ing fins, and other external surfaces of the engine are kept

clean at all times. Every 100 hours of operation (more often under extremely

dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Ensure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed

will cause engine damage due to overheating.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create afire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of use, whichever comes

first. Spark plug type and gap setting is shown in Product Specifications section of this manual.

MAINTENANCE

IN=LINE FUEL FILTER (See Fig. 19)

The fuel filter should be replaced once each season. Iffuel filter becomes clogged, obstructing fuel flow to carburetor,

replacement is required.

• With engine cool, removefilter and plug fuel linesections.

• Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

• Ensure there are no fuel line leaks and clamps are properly positioned.

• Immediately wipe up any spilled gasoline.

CLAMP

I CLAMP _--_

FUEL FILTER _ J U0667

Fig. 19

CLEANING

Clean engine, battery, seat, finish, etc. of all foreign matter.

• Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip

and loss of drive.

DECK WASHOUT PORT (See Fig. 21)

Your tractor's deck is equipped with a washout port on its surface as part of its deck wash system. It should be

utilized after each use.

1. Drive the tractor to alevel, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.

IMPORTANT: Make certain the tractor's discharge chute is directed AWAY from your house, garage, parked cars, etc.

Remove bagger chute or mulch cover if attached.

2. Ensure the attachment clutch control is in the "DISENGAGED" position, set the parking brake, and

stop the engine.

3. Thread the nozzle adapter (packaged with your tractor's Operator's Manual) onto the end of your garden hose.

4. Pull backthe lock collar of the nozzle adapter and push

the adapter onto the deck washout port at the left end

of the mower deck. Release the lock collar to lock the adapter on the nozzle.

NOZZLE ADAPTER

CAUTION: Avoid all pinch points and

movable parts (See Fig. 20)

MOWER NOT SHOWN

Fig. 20

• Keep finished surfaces and wheels free of all gasoline, oil, etc.

• Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans-

mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use

compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

Fig. 21

IMPORTANT: Tug hose ensuring connection is secure.

5. Turn the water on.

6. While sitting in the operator's position on the tractor, re-start the engine and place the throttle lever in the

Fast ",_" position.

IMPORTANT: Recheck the area making certain the area is clear.

7. Move the tractor's attachment clutch control to the "EN- GAGED" position. Remain in the operator's position with

the cutting deck engaged until the deck is cleaned.

8. Move the tractor's attachment clutch control to the "DISENGAGED" position. Turn the ignition key to the

STOP position to turn the tractor's engine off. Turn the

water off.

9. Pull back the lock collar of the nozzle adapter to discon- nect the adapter from the nozzle washout port.

10.Move the tractor to a dry area, preferably a concrete or paved area. Place the attachment clutch control in the

"ENGAGED" position to remove excess water and to help dry before putting the tractor away.

fitting could expose you or others to

WARNING: A broken or missing washout

thrown objects from contact withthe blade.

• Replace broken or missing washout fitting immediately, prior to using mower again.

• Plug any holes in mower with bolts and Iocknuts.

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS iNJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress brake pedal fully and set parking brake. Place motion control lever in neutral position.

* Place attachment clutch in "DISENGAGED" position. * Turn ignition key to "STOP" and remove key. * Ensure the blades and all moving parts have completely stopped. * Disconnectsparkp_ugwirefromsparkp_ugandp_acewirewhereitcannotcomeincontactwithp_ug_

TO REMOVE MOWER (See Fig. 22)

• Place attachment clutch in "DISENGAGED" position.

• Lower attachment lift lever to its lowest position.

• Roll belt off engine pulley (M) and belt keepers (G).

• Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

• Remove clutch cable spring (Q) from idler arm (R).

• Disconnect front link (E) from mower - remove retainer

spring and washer.

• Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift

link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: After rear lift links are dis=

• Slide mower out from under right side of tractor.

connected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of

the lever.

iMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR,

REMOVE THE FRONT LINK (E) AND REAR LIFT LINKS (C) FROM TRACTOR AND HOOKTHE CLUTCH SPRING (Q) INTO THE CABLE GUIDE ON FRONT EDGE OF

LOWER DASH.

TO iNSTALL MOWER (See Fig. 22 =27)

Ensure tractor is on level surface and engage parking brake.

• Lower attachment lift lever to its lowest position.

Have a tight grip on lift lever, lower it

CAUTION: Lift lever is spring loaded.

slowly and engage in lowest position.

NOTE: Ensure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

• Slide mower under tractor until it is centered under tractor.

Fig. 22 03042tex

SERVICE AND ADJUSTMENTS

• ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside

of tractor chassis and secure with retainer spring.

• Repeat on opposite side of tractor.

Fig. 23

ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D)

on rear mower bracket and secure with washer and retainer spring.

Fig. 24

ATTACH FRONT LINK (E) - Work from left side of trac- tor. Insert rod end of link assembly through front hole

in tractor front suspension bracket (F).

• Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J).

Fig. 25

• Hook end of clutch cable spring (Q) into hole in idler arm (R).

• Push clutch cable housing guide (P) into bracket, slide collar (L) onto guide andsecure with retainer spring (K).

• Install belt on engine pulley (M), in belt keepers (G).

Fig. 26

iMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

• Raise attachment lift lever to highest position.

• If necessary, adjust gauge wheels before operating mower asshown inthe Operation section of this manual.

Fig. 27 03042tex

+ 44 hidden pages

Ariens A20BH42 (96046001100), 96046001100, 93604200, 936042 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual