Argos Kids Sywell - 4 Drawer Chest ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 69cm

Depth - 39.5cm

Height - 75cm

Kids Sywell - 4 Drawer Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 15/12/14

Important - Please read these instructions fully before starting assembly

281/8616

268/5461

247/4562

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 23kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D2920A)

(718 x 396mm)

Back (X689-684)

(689 x 684mm)

Right Side (D2555A)

(718 x 396mm)

1

Top (D2546A)

(658 x 394mm)

Drawer Front (D2550A)

(654 x 162mm) x 4

2

Rail (D2549A)

(658 x 78mm) x 2

3

4

5

10

Drawer Base (T636-327)

(636 x 367mm) x 4

Drawer Back (W625-124)

(625 x 124mm) x 4

9

6

7 8

Left Drawer Side (W370-124LH)

(370 x 124mm) x 4

Right Drawer Side (W370-124RH)

(370 x 124mm) x 4

6

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill
(do not use for
fitting screws)

A

Wooden dowel (F22) x 6

B

Metal dowel (F901) x 16

C

D E F

G H I

L

M

J K

9mm Screw (F74) x 8 9mm Screw (F73) x 16

Drawer runner (F1004) x 8

Knock-in Peg (F171GY) x 16

13mm Screw (F79) x 1

Small locking
nut (F3) x 8

Large locking
nut (F900) x 8

Nail (F51) x 20 Bracket (F327) x 1

Handle (F315) x 4

25mm Screw (F95) x 8

O

Plastic Nail (F91) x 4

N

Wedgefix (F639) x 16

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 4

B

Prepare the 4 drawer
fronts

Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .

Note: Tighten the metal
dowels up fully against
the panels.

B

5

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .

Note: Arrow on locking
nut must point towards
hole in edge of panel.

E

7

8

Step 2

Step 3

B

B

5

Attach the drawer
sides to the drawer
front

Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

7
8

5

E

7
8

E

x 4 x 4

x 4

Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.

E

B

B

E

Small groove

Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.

E

E

7

8

7

8

5

Assembly Instructions

5

Step 4

5

C

C

Fit the drawer base

Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .

Step 5

Fit the drawer back

Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .

Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .

Step 6

9

7 8

5

6

7 8

9

6

6

C

Attach the handles

Attach a handle to
each of the drawer fronts
. using screws .

Note: Do not
overtighten the screw.

L

F

5

7 8

Step 7

Fit the wedgefixes

Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.

N

x 4

x 4

x 4

C

C

x 4

N

N

N

N

N

9

7

6

7

8

9

8

L

F

F

5

Finished

front edge

Finished

front edge

Assembly Instructions

6

Step 8

Prepare the left side

a: Place 4 runners on

the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 4 metal dowels
into the left side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .

M

1

Finished

front edge

I

M

I

B

1

M

I

1

Finished

front edge

I

M

Step 9

Prepare the right side

a: Place 4 runners on

the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .

Screw 4 metal dowels
into the right side .

b: Slide the runner

back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .

M

2

I

B

2

M

I

2

a:

b:

B

B

I

M

I

M

I

M

I

M

B

B

1

I

I

I

I

I

M

I

M

I

M

I

M

B

B

B

B

1

2

2

I

I

I

I

Finished

front edge

Finished

front edge

a:

b:

Finished

front edge

Finished

front edge

Assembly Instructions

7

Step 10

Prepare the top

Tap 2 wooden dowels
into the top .

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

Insert 4 large locking
nuts into the
top .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Fix the bracket in the
middle of the top ,
flush to the back edge
using screw .

Fit the top to the right
side

Push the top onto
the right side .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Step 11

D

10mm

A

A

3

D

3

3

2

D

3

D

B

D

plain chipboard surface

3

A

D

D

D

A

Finished

front edge

D

G

K

K

G

K

3

plain chipboard surface

3

2