Argos Kensington - 3 Drawer 2 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assembly

Kensington - 3 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference

414/6946

4111335

Issue 2 - 28/07/15

Width - 85.9cm

Depth - 49.5cm

Height - 198.8cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 59kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Drawer Front (DF2414)

(79.1 x 19.2cm) x 3

Drawer Back (W765-124)

(76.5 x 12.4cm) x 3

Left Drawer Side (W370-124LH)

(37 x 12.4cm) x 3

Drawer Base (T776-367)

(77.6 x 36.7cm) x 3

Right Drawer Side (W370-124RH)

(37 x 12.4cm) x 3

Components - Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

1 2 3

4 5

Tools required

Scissors / Rule / Hammer / Cross-head screwdriver / Square / Spirit level / Step ladder

Eye protection (when using a hammer or drill) / Electric drill (only use when drilling into walls)

Components - Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

2

6

7

9

8

11 12

Top (DF2409)

(85.9 x 49.5cm)

Shelf (DF2413)

(79.7 x 47.4cm)

Front Plinth (DF2417)

(85.9 x 9.2cm)

Side Plinth (DF2431)

(47.5 x 9.1cm) x 2

Back (X1914-823)

(191.4 x 82.3cm)

13

14 15

16

Hanging Rail (FHR791)

(79.1cm long)

10

Left Side (DF2410)

(197.3 x 47.5cm)

Right Side (DF2411)

(197.3 x 47.5cm)

Rail (DF2412)

(79.7 x 8.9cm) x 5

Left Door (DF3874)

(120.6 x 39.4cm)

Right Door (DF3780)

(120.6 x 39.4cm)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020

3

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D E F

G H I

L

N

Small locking nut (F3) x 6

C

Nail (F51) x 34

M

J K

O

Drawer runner (F1004) x 6

Knock-in Peg (F171GY) x 12

Large locking nut (F900) x 20

Metal dowel (F901) x 26

Wooden dowel (F22) x 20

25mm Screw (F50) x 6

19mm Screw (F461) x 8

9mm Screw (F74) x 6

9mm Screw (F73) x 12

Plastic Nail (F91) x 4

Handle (F220) x 8

P Q

Hinge plate (F523) x 6

Hinge (F522) x 6

S

Shelf stud (F110) x 2

Rail Holder (F891) x 2

13mm Screw (F63) x 16

Wedgefix (F639) x 12

R T

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

1

Assembly Instructions

4

Step 1

A

C

2

3

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the 3 drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

A

1

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

C

2

3

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

2 3

1

C

2 3

A

1

2

3

x 3

1

Assembly Instructions

5

Step 4

F

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

5

2 3

1

4

2 3

5

4

F

2 3

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

N

F

N

5

2

3

4

2

3

5

Attach the handles

Attach 2 handles to each drawer front using screws .

H

1

R

H

R

1

x 3

Finished

front edge

Finished

front edge

Finished

front edge

D

Assembly Instructions

6

Step 8

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

b: Slide the runners

back the other way and fit the 2nd screw into the corresponding holes in the left side .

Insert 2 large locking nuts into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap 2 wooden dowels into the left side .

c: Screw 7 metal

dowels into the left side .

To fit the rail holder screw through the top hole with screw and into the mark hole drilled in the left side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

6

J

B

6

M

A

6

D

6

a:

b:

c:

J

M

K

O

K

O

P

6

O

K

6

K

J

M

J

M

J

M

P

J

B

10mm

D

K

O

A

6

D

Assembly Instructions

7

Step 9

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

b: Slide the runners

back the other way and fit the 2nd screw into the corresponding holes in the right side .

Insert 2 large locking nuts into the right side .

Tap 2 wooden dowels into the right side .

c: Screw 7 metal

dowels into the right side .

To fit the rail holder screw through the top hole with screw and into the mark hole drilled in the right side . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

7

J

B

7

M

A

7

D

7

P

7

O

K

7

K

P

J

M

a:

b:

c:

Finished

front edge

Finished

front edge

Finished

front edge

J

M

J

M

J

M

P

7

J

B

A

7

K

O

Finished

front edge

D

Assembly Instructions

8

Step 10

Prepare the shelf

Insert 4 large locking nuts into the shelf .

Tap 4 wooden dowels into the shelf .

9

D

9

B

D

B

Finished

front edge

9

Step 11

Fit the shelf to the right side

Push the shelf onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the shelf .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Step 12

9

7

B

9

B

D

B

Prepare the 5 rails

Insert 2 large locking nuts into each of the 5 rails .

Tap 2 wooden dowels into each of the 5 rails .

11

D

11

B

x 5

A

B

11

Finished

front edge

9

7

Assembly Instructions

9

Step 13

Fit the 5 rails

Push the 5 rails onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each of the 5 rails .

11

7

B

11

Step 14

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 2 large locking nuts fitted to the shelf and the 5 rails .

6

B

9

11

7

11

Note: Fit this rail last and support it until the left side has been fitted in the next step.

11

6

Note: The holes for this rail must be on this side

G

8

Polystyrene

block

Polystyrene

block

Polystyrene

block

Polystyrene

block

Fit the top

Note: To make it easier to fit the top and plinths, place polystyrene blocks from the packaging underneath the side panels to raise the assembly.

Push the top onto the assembly.

Use a screwdriver to tighten the 4 large locking nuts fitted to the sides and .

B

6 7

8

Assembly Instructions

10

Step 15

Prepare the top

Screw 4 metal dowels into the top .

A

8

A

Step 16

Step 17

Warning: The unit is heavy. Lift with care.

8

11

Secure the top rail to the top

Screw through the 2 holes in the top and into the top rail using 2 screws .

8

11

G

Assembly Instructions

11

Step 18

Step 19

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

16

E

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

16

Fit the 4 plastic nails

Tap 4 plastic nails into the bottom edge of each of the sides and . .

L

6

7

yy

xx

b:

E

16

L

6

7

Assembly Instructions

12

Step 20

D

Prepare a side plinth

Insert a large locking nut into 1 of the side plinths .

Tap a wooden dowel into the side plinth .

13

B

13

D

Step 21

Prepare the other side plinth

Insert a large locking nut into the side plinth . .

Tap a wooden dowel into the side plinth .

13

B

13

D

B

D

Finished

top edge

13

Finished

top edge

13

B

Finished

top edge

Profiled

top edge

Finished

top edge

Profiled

top edge

Prepare the front plinth

Screw 2 metal dowels into the front plinth .

Step 23

A

12

Fit the plinths together

Push the 2 side plinths onto the front plinth .

Use a screwdriver to tighten the large locking nuts fitted to the side plinths .

13

12

B

13

A

12

13

Step 22

Assembly Instructions

13

Step 24

Fit the plinths

Position the 3 plinths around the outside of the assembly, ensuring that the bottom edge of the plinths are flush with the bottom edge of the sides, as shown.

Secure the 2 side plinths through the left end and right end using screws .

Carefully stand the unit up for the next step.

13

6

7

G

Warning: The unit is heavy. Lift with care.

Step 25

Fit the drawers

Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .

Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.

Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.

I

M

I

2nd threaded

hole

M

I

2 3

G

6

7

G

13

I

2

3

Assembly Instructions

14

Step 26

Step 27

10

O

Fit the hanging rail and shelf studs

Push the hanging rail into the rail holders fitted to the side panels.

Push the 2 shelf studs down into the holes in the shelf to act as door buffers.

S

9

10

O

Prepare the 2 doors

Push fit 3 hinges into each of the 2 doors and .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

K

Q

15

14

90

Q

10

S

Q

K

Q

K

Q

K

Q

K

Q

K

Q

K

15

14

Assembly Instructions

15

Step 28

Fit doors and handles

Note: The easiest way to attach each door and . is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle to

each door and using screws .

Q

P

Q

P

R

H

14

15

14 15

a: b:

c: d:

P

Q

P

B

P

Q

A

Q

P

B

e:

R

H

14

15