Mia Daybed & Drw. White
Assembly Instructions - Please keep for future reference
8042572
Dimensions
Length - 193,2cm
Depth - 95,4cm
Height - 68cm
Weight - 47,3kg
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@fl exa.dk
Issue 1 - 08/07/17
Safety and Care AdviceSafety and Care Advice
Important – Please read these instructions fully before starting assembly
80-27904-20 Singlebed
IMPORTANT! KEEP FOR FUTURE REFERENCE
PLEASE DISPOSE OF PACKAGING MATERIAL.
PLASTIC BAGS CAN BE DANGEROUS TO YOUNG CHILDREN
WARNING! Not suitable for children under 4 years.
WARNING! Do not place this child’s bed near heat sources, windows and other furniture.
WARNING! Do not use this child’s bed if any of the parts are broken, torn or missing.
WARNING! Once assembled, this bed must not be disassembled. Screws must not be removed once inserted.
This child’s bed is to be used with a 1900mm x 900mm ma ress.
Suitable for over 4 years old to adults.
All assembly Įxings should be checked periodically and re-
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not
be placed too close to other furniture or windows, bl
placed either
Any addi
ght to any wall or have a gap of 300mm between the wall and the side of the bed.
Always place the side of the bed with the safety rail against a wall.
onal or replacement parts should only be obtained from the manufacturer or distributor.
This product complies to standard BS8509: 2008+A1:2011
ind cords, curtain pulls or other strings or cords, and should be
ghtened where necessary.
CARE AND MAINTENANCE
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.
1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
If you have damaged or missing components,
Components - Parts
call the Customer Helpline:
Please check you have all the parts listed below
0045 7668 8055
End panel Right x1
1
(95,4x68,0x1,6cm)
No. 4301-1609541-40
Trundle bed front x1
4
(189,0x22,0x1,6cm)
No. 4301-1618901-40
End panel Left x1
2
(95,4x68,0x1,6cm)
No. 4301-1609542-40
Slat x28 (89,7x6,5x1,5cm)
5
No. 12-01508971
Distance piece x2
3
(90,0x6,5x3,1cm)
No. 12-03109001
Bedside x2
6
(190,0x12,7x2,2cm)
No. 4301-2219001-40
Trundle back x1
7 8
(189,0x8,9x2,0cm)
No. 1331-18901 No. 12-02019002-40 No. 12-02018704
List x1
10
(174,0x2,6x2,0cm)
No. 12-02017402
Back rail x1
(190,0x8,9x2,0cm)
List x2
9
(187,0x2,6x2,0cm)
3
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
No. 3913-06070
A
M6x70mm Connecting bolt x10
No. 3901-45040
D
No. 3922-06014
B
M6 ø10x14mm Barrel nut x10
No. 3902-35016
E
C
4,0x30mm Chipboard screw x56
F
No. 3901-40030
No. 3908-70040
4,5x40mm Chipboard screw x4 3,5x16mm Chipboard screw x8 7,0x40mm Confi rmat screw x37
No. 3909-63060
G
6,3x60mm Assembly screw x8 ø14mm Felt pad x4
No. 4003-002
H i
10x40mm Dowel x8
No. 3930-10040 No. 4005-034
J
ø26mm Castor x4
Tools required
Phillips
screwdriver
(medium)
Flatblade
screwdriver
(medium)
Allen key
4mm incl.
No. 4033-002
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
4
Assembly Instructions
Step 1
Insert the dowels H into
the holes in bedsides
8
and back rail
.
6
It may be necessary
to tap the dowels in
very gently with a small
hammer.
9
6
using
to
Attach the lists
the bedsides
F
screws
and D.
Step 2
6
Attach the bedside
and back rail
endpanels
8
1
and 2
by placing the dowels
into the holes in the end
panels.
Insert barrel nuts
the holes in bedside
and back rail
endpanels
using bolts
8
1
and 2
A
. Note that
the holes for the barrel
nuts on the back rail
should be facing out.
to the
B
into
6
. Attach
D
F
H
H
D
H
9
F
D
6
8
H
H
A
B
2
A
A
B
8
6
B
1
A
A
B
A
Step 3
Attach the second
6
bedside
endpanels
by placing the dowels
into the holes in the end
panels.
Insert barrel nuts
the holes in bedside
Attach endpanels
2
using bolts A.
5
to the
1
and 2
B
into
1
and
B
1
B
6
.
2
A
B
6
A
Assembly Instructions
Step 4
Place two slats 5 in the
ends of the bed, against
the end panels. Fasten
with four chipboard
C
screws
Place one slat
.
5
in the
middle of the bed. Follow
the measurements.
6
Push the bedsides
together whilst attaching
5
middle slat
to the
bed with two chipboard
C
screws
.
Step 5
Position the remaining
5
twelve slats
bed with an approximate
distance of 66 mm
between each.
in the
C
852 mm 852 mm
C C C
5 5 5
C
66 mm
C
Fasten each slat with two
screws
C
5 55 55 55 55 55 5
C
6
Assembly Instructions
Step 6
Attach the list 10 to the
4
trundle front
screws
F
using
F
.
Step 7
Attach the trundle front
4
and back 7 to the
3
distance pieces
G
screws
.
Place felt pads
ends of the trundle back
7
.
using
i
to the
F
10
4
G
G
i
3
G
4
i
7
G
i
3
Step 8
Attach castors
distance pieces
E
screws
.
J
to the
3
using
G
J
E
E
E
J
3
E
J
35 mm
3
E
J
J
E
J
3
7
Assembly Instructions
Step 9
Position slats 5 in the
bed with an approximate
distance of 64 mm
between each and
130mm from the edge of
3
the distance piece
Fasten each slat with two
screws
Assembly is complete.
C
.
C
64-65 mm
C
5555555555555
130 mm
C
If you need help or have damaged or missing parts,
E-mail: order@fl exa.dk
Ref.no. 44-01729-20 A Stand: 081117 Page 10 (80-27904-20)
call the Customer Helpline: 0045 7668 8055
8
Loading...