Page 1
HM Maine Coffee Table
Assembly Instructions
-
Please keep for future reference
806/4402
798/5362
792/8044
764/8070
797/9323
803/2276
Dimensions
Width - 80cm
Depth - 40cm
Height - 45cm
-
Important
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Please read these instructions fully before starting assembly
Version 3 Date: 18/09/17
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fi ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its fi nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your fl oor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Top panel
1
(80 x 40cm)
Argos = 0345 6400800
Top support x 2 (76.8 x 6cm)
4
Bottom support x 2
5
(76.8 x 6cm)
Bottom panel
2
Side panel x 2
3
Pilot holes for guidance only
(76.8 x 39.6cm)
(43.5 x 39.8cm)
2
Page 4
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
A
39mm Locking pin x 16
D
15mm Screw x 12
B
30mm Dowel x 8
E
Plastic support x 6
C
15mm Locking nut x 16
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Drill
7mm Suitable drill bit
(for use with wall plug)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Page 5
Assembly Instructions
Step
Attaching bottom panel
a:
Plastic supports onto
the Bottom support .
Note:
of the Plastic supports
1
Use Screw to fix the
Be sure the edges
D
E
5
E
even with the edges of
the
Bottom support
5
.
a:
D
D
D
E
E
D
5
E
E
X 2
b:
Position the Bottom
supports onto the
Bottom panel use
Screws .
Insert Dowels into the
Bottom panel .
5
2
D
B
2
b:
D
D
D
D
2
B
5
D
5
D
D
B
B
B
4
Page 6
Assembly Instructions
Step 2
Attaching side panel
a:
Screw Locking pins
into the Side panel .
A
3
Note: Insert locking pins
as far as shown.
Do not over tighten.
Insert Dowels into the
Side panel .
B
3
a:
A
A
A
A
B
B
A
3
X 2
b:
Position Top supports
4
onto the Side panel
.
3
Insert Locking nut
into the Top supports
C
4
.
Use a screwdriver to turn
Locking nut clockwise
C
to lock.
b:
C
4
4
C
C
Continued on next page.
5
3
Page 7
Assembly Instructions
Step 2 - continued
c:
Position Bottom panel
2
onto the Side panel
.
3
Insert Locking nuts
into the Bottom panel .
C
2
Use a screwdriver to turn
Locking nut clockwise
C
to lock.
c:
C
2
C
C
3
d:
Position Side panel
3
onto the unit.
Insert Locking nuts
into the Bottom panel
and Top supports .
C
2
4
Use a screwdriver to turn
Locking nut clockwise
C
to lock.
d:
C
3
C
C
C
C
2
4
4
6
Page 8
Assembly Instructions
Step 3
Attaching top panel
a:
Screw Locking pins
into the Top panel .
A
1
Note: Insert locking pins
as far as shown.
Do not over tighten.
a:
A
A
A
A
A
A
A
1
A
A
b:
Position Top panel
onto the unit.
1
Insert Locking nuts into
the Side panels , Top
supports .
4
C
3
Use a screwdriver to turn
Locking nut clockwise
C
to lock.
b:
C
1
C
4
C
C
C
C
C
C
C
4
3
3
7
Page 9
Assembly Instructions
Step 4
Finishing the unit
It would be useful
Note:
to ask someone to help
you at this stage.
With help, place the unit
in the intended position.
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
8
Loading...