2 Door Media Unit/Low Sideboard
Assembly Instructions - Please keep for future reference
033 xx 6003
482/0437
Dimensions
Width - 117.2cm
Depth - 38.8cm
Height - 57.6cm
GREAT BRITAIN
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev A - 30/09 /15
MADE IN
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
If you have damaged or missing panels, call the
Components - Panels
Customer Helpline: 01709 534123
for important information when contacting Customer Helpline.
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
9885
Top
(111.8x38.8cm)
9887
Left End
(50.8x38.2cm)
9888
Right End
(50.8x38.2cm)
Please turn to back page
9893
Door x 2
(42.4x27.8cm)
9886
Bottom
(101.2x34.0cm)
9889
Plinth
(101.2x7.6cm)
9891
Small Shelf x 2
(26.7x33.8cm)
9892
Large Shelf
(44.5x33.8cm)
9890
Left Divider
(41.4x34.0cm)
684xx5505
Trim x 2
(50.8x5.0 x1.2cm)
9895
Right Divider
(41.4x34.0cm)
9894
Back x 2
(43.3x28.6cm)
2
If you have damaged or missing components, call the
Components - Fittings
Customer Helpline: 01709 534123
for important information when contacting Customer Helpline.
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
A
D
G
J
M
Large cam x 16
Code 760001103
Panel pin x 20
Code 760001012
Fully cranked 26mm
hinge x 4
Code 652001120
Wooden dowel x 4
Code 770001006
Shelf Pin x 8
Code 760001137
E
H
K
B
Metal dowel x 16
Code 760003004
18mm bolt x 4
Code 700002021
Hingeplate x 4
Code 653006000
Screw x 8
Code 690001008
C
F
I
L
Shelf Support x 8
Code 681003001
Panel pin guide x 1
Code 684004501
Handle x 2
Code 644003511
45mm screw x 4
Code 690001075
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Bradawl
Ruler - Use this ruler to help correctly identify the screws
mm
10
0
20
30
3
40
50
60
70
80
90
100
110
120
130
140
Eye protection
(when using a
hammer)
160
150
170
Exploded View
0001
0007
0007
9998
0006
684xx6531
0004
9164
0003
9999
0005
0003
0005
0004
0002
0006
684xx6531
4
Assembly Instructions
Step 1
Fitting cams to the
bottom panel.
Insert 4 metal cams
A
into the bottom panel
.
9999
Note: Ensure cam arrow
points towards the edge
with the hole.
Step 2
Fitting cams to the
plinth panel.
A
x4
A
x4
A
A
A
A
A
9999
A
A
Insert 4 metal cams
to the plinth panel .
A
9164
Step 3
Fitting dowels to the
top panel.
Insert 8 metal dowels
into the top panel
Note: Insert metal
dowels as far as
B
shown by arrows. Do not
over tighten.
B
9998
B
x8
A
A
9164
B
B
B
B
B
9998
B
B
B
5
B
Assembly Instructions
Step 4
Attach dowels, cams
and hinges to both of
the end panels.
Insert 4 metal dowels ,
2 hinges and 2
cams into the left end
panel .
H
A
0001
Repeat on the right end
panel .
0002
B
B
x8
A
x4
A
0001
A
H
x4
B
H
B
B
B
B
H
A
A
H
0002
B
B
B
H
Step 5
Attach dowels, cams to
both divider panels.
Insert 2 cams
and 2 wooden dowels
into the divider
panel .
0003
Repeat on remainding
divider.
A
J
J
x4
A
x4
A
A
0003
Holes not used at
J
X 2
J
this stage.
6
Assembly Instructions
Step 6
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
G
G
x4
A
B
K
x8
E
x4
I
x2
G
Correct
90
Incorrect
G
98
0006
Bradawl
c: Secure hinges to
doors using screws .
d: Secure handle to
doors using bolts
G
K
I
E
C
0006
K
K
K
K
0006
Repeat on the second
door.
7
D
E
0006
E
I
Assembly Instructions
Step 7
Connect the top panel
to the left end panel
and the divider panels.
Connect the dowels in the
top panel to the
dowels in the left end
panel and divider
panels .
IMPORTANT.
Please ensure divider
panels are
positioned as shown.
Turn cams 180 degrees to
lock.
9998
0001
0003
0003
Edged face
0001
0003
0003
9998
Large silver ttings
visible in this face
Large silver ttings
visible in this face
Step 8
Connect the bottom
and the plinth panel to
the left end panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel and the
plinth panel .
Ensure that dowels in both
panels locate
0003
into bottom panel
guide holes.
9999
Turn cams 180 degrees to
lock.
0001
9164
9999
0001
9890
0003
Edged face
9164
0003
Ensure plinth sits
flush.
Ensure plinth is
not overhanging.
9999
8
Assembly Instructions
Step 9
Connect the right end
panel to the top,
bottom and plinth
panel.
Connect the dowels in
the top panel to
the cams in the right end
panel .
Connect the dowels in
the right end panel
to the cams in the bottom
panel and the
plinth panel .
Turn cams 180 degrees to
lock.
0002
9999
9998
0002
9164
9164
9890
9999
0002
9998
Step 10
Secure the bottom
panel to the divider
panels.
Using 4 screws ,
secure the bottom panel
to the divider
9999
panels .
Lay unit on its front to
attach the backpanels
0003
L
L
x4
0003
L
L
L
9890
9999
L
0003
9
Assembly Instructions
Step 11
Squaring up the unit.
Important:
Ensure a tape
measure is used
to square up unit!
Before securing the back
it is necessary to square
up the unit.
You can do this by
measuring between
XX - XX and YY - YY
ensuring these are the
same (DIAG 1).
If they are not (DIAG 2)
Apply slight pressure as
indicated (DIAG 3) until
they are the same.
XX
YY
XX
DIAG 1
XX
YY
YY
XX
YY
DIAG 2
YY
XX
YY
XX
YY
XX
DIAG 3
YY
XX
Measure to
external corners
Step 12
Attach the backpanel
Slide the back panel into
the end and top panel
grooves.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
Ensure that the
backpanel is fully
inserted into groove.
D
x20
F
x1
Plain chipboard surface.
D
D
F
D
10
Assembly Instructions
Step 13
Lay unit on its back
to attach the trims
Remove protective film
from silver trim.
Locate the notch on
the trim into the grooves
in the end panels.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and trims to
protect the trims.
Ensure that the trims
are inserted fully.
Step 14
Fitting the shelf
supports.
Stand Unit Upright.
Insert 8 shelf supports .
Once inserted, seat shelves
on top of the shelf
0004
supports.
C
C
x8
11
Assembly Instructions
Step 15
Insert the shelf pins
and insert shelves.
Insert 8 of the shelf pins
M
into the 2 divider
panels at
your desired height.
Place the shelves
on top of the shelf pins.
0003
0005
M
x8
M
M
Step 16
Hanging doors
a: With help, slot door
hinges onto hinge plates.
Ensure screw on hinge
slides into the slot on
hingeplate.
See Diagrams 1, 2 and 3.
b: Tighten screw shown
to lock hinges in
position.
M
A
M
B
See ‘Hinge adjustment’
page if the doors
need adjusting.
Repeat the process on
the remaining door.
Diagram 1
B
Ensure the underside of screw
B slides into slot on hingeplate.
Diagram 2
B
Hinge correctly attached to
hingeplate.
Diagram 3
B
Hinge incorrectly attached to
hingeplate.
12
Assembly Instructions
Step 17
Hinge adjustment
A
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
B
Re-tighten screws.
c: To move doors left
or right: loosen or
tighten screw as shown.
Be careful not to fully
unscrew.
C
13
Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
01709 534123
(by contacting the customer service line your statutor y rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
Loading...