1 Drawer Display Unit
Assembly Instructions - Please keep for future reference
042 xx 3048
Dimensions
Width - 74.0cm
Depth - 35.8cm
Height - 161.7cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967
Please turn to back page for important information when contacting Customer Helpline.
01709 534123
Rev C - 22/04/2013
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
8828
8553
5671
622xx7002
Left drawer side (30x10cm)
623xx7002
Right drawer side (30x10cm)
Top (74x35.8cm)
Plinth (63.4x76cm)
Drawer Bottom
(61.2x29.8cm)
8829
8832
Bottom x5 (63.4x31cm)
Backpanel (152.1x64.4cm)
8830
Left End Panel
(159.5x35.2cm)
8581
Drawer Front
(63x15.7cm)
8831
Right End Panel
(159.5x35.2cm)
624xx7010
Drawer back (60.1x10cm)
684xx3048
Trim x 2
2
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 0845 0613967
for important information when contacting Customer Helpline.
01709 534123
Please turn to back page
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
J
M
G
A
D
Large cam x 28
Code 760001103
20mm bolt x 2
Code 700002006
Panel pin x 8
Code 760001012
8mm screw x 4
Code 700003510
Cam cover sticker x 6
Code 682xx2011
E
H
B
K
Metal dowel x 30
Code 760003004
12mm screw x 2
Code 690001099
9mm bolt x 2
Code 690001078
Runner x 2
Code 760001040
C
F
L
Small cam x 2
Code 760003005
Panel pin guide x 1
Code 684004501
I
Handle x 1
Code 653003512
Support Bracket x 1
Code 760001901
Tools required
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
mm
10
0
20
30
3
40
50
60
70
80
90
100
110
120
130
140
150
Drill
160
170
Exploded View
Please check you have all the fittings listed below
8828
8830
8829
8832
622xx7002
8831
684xx3048
8553
624xx7010
684xx3048
5671
8581
623xx7002
4
Assembly Instructions
Step 1
Fitting dowels to top
panel.
B
Note: Insert metal
dowels as far as
B
shown by arrows.
Do not over tighten.
Step 2
Fitting cams to the
bottom panels x5.
A
Fittings you will need for this step:
B
x4
B
B
8828
Fittings you will need for this step:
A
x20
A
A
B
B
Note: Ensure cam
arrow points towards
the edge with hole.
Step 3
Fitting cams to the
plinth panel.
A
Note: Ensure cam
arrow points towards
the edge with hole.
8828
A
REPEAT ON REMAINING BOTTOM PANELS
Fittings you will need for this step:
A
x4
A
A
A
A
A
5
Assembly Instructions
Step 4
Fitting cams & dowels
to the end panels.
A
Note: Ensure cam
arrow points towards
the edge with hole.
B
x24
A
x4
B
B
B
B
B
B
B
B
B
B
B
B
B
B
8831
B
B
B
B
B
8830
B
A
A
B
B
B
B
Step 5
Attaching runners to
end panels
Position the runner so
that the second hole
from the front of the
runner lines up with the
pre-drilled hole nearest
to the grooved edge of
the panel. Use screws
J
to secure the runner.
Front of runner
Slide the runner forward
revealing the back of the
runner. The second hole
to the back of the runner
should now line up with
the second pre-drilled
hole.
K
x2
REPEAT ON
J
x4
8831
8830
J
K
Step b
J
K
Step a
6
Assembly Instructions
Step 6
Drawer assembly
a: Insert dowels into
drawer front.
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
(x2)
C
(x2)
A
B
B
B
8581
Right hand side
623xx7002
b: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
622xx7002
623xx7002
c: Insert wooden dowels
in drawer back
into holes in
624xx7010
left
622xx7002
right hand
623xx7002
drawer sides.
C
Left hand side
622xx7002
Left hand side
622xx7002
C
C
Drawer Back
624xx7010
Continued on next page.
7
Right hand side
623xx7002
Assembly Instructions
Step 6 - Continued
Drawer assembly
Continued...
d: Slide drawer bottom
into grooves in the left
and right drawer sides
and the drawer back.
Ensure foil on the
drawer bottom is facing
upwards.
e: Locate the metal
dowels (already inserted)
in the drawer front into the
small cams in the left and
right hand drawer sides.
D
E
624xx7010
622xx7002
7010
SLIDE!
623xx7002
Plain chipboard surface
to underside.
622xx7002
Turn cam 180 degrees
to lock
f: Secure handles to the
drawer front.
8581
D
(x2) (x1)
I
F
8581
7010
623xx7002
D
D
I
8
Assembly Instructions
Step 7
Connect right hand
and and top panel.
Attach the top panel
8828
to the right end
panel .
Note: You may need a
small screwdriver.
8831
8828
8831
Step 8
Connect right hand
end with bottom
panels x5 and plinth.
Connect the right end
panel to the 5 x
bottom panels and the
plinth.
Note: You may need a
small screwdriver.
8830
8830
8829
8829
8829
8553
8829
Ensure plinth sits
flush.
9
Ensure plinth is
not overhanging.
Assembly Instructions
Step 9
Connect the left hand
end panel.
Connect the dowels in
the left end panel
in order from the top
into the bottom panels
and finally the
8829
plinth panel
8830
8553
8829
8829
8829
8830
Step 10
Slide in back panel
Slide the back panel
into the grooves
8832
in the left and right hand
ends.
To ensure that the back
panel sittings into the
groove in the top panel,
stand the unit on its
head.
CAUTION: Two people
required to lift the unit.
8553
8829
8832
10
Assembly Instructions
Step 11
Insert back panel.
Ensure that the back
panel sits firmly inside all
of the grooves before
laying the unit back down
to secure the bottom
panel.
8832
Step 12
Secure the back
panel.
Slide the back panel into
the grooves.
Use the panel pin guide
when locating the panel
pins. This will hold the
panel pins vertical and
ensure the correct
distance from the edge.
G
G
x8
F
x1
8832
11
Assembly Instructions
Step 13
Turn unit over to
attach the trims
Locate the notch on
the trim into the grooves
in the end panels.
To insert trims use a
hammer, place a
cardboard packing piece
between the hammer
and trims to protect the
trims.
Ensure that the trims
are inserted fully.
8830
8831
12
Assembly Instructions
Step 14
Stand unit upright to
insert drawers.
For this step we
recommend you follow
the helpful hints page.
H
(x2)
13
H
2nd HOLE
Assembly Instructions
Step 16
Locate drawers helpful
hints
a: Pull sliding part of
drawer runners out
so they are fully
extended.
K
b: Locate drawer onto
runners.
c: Locate screwdriver
into second threaded
hole in drawer runner .
K
d: Keeping screwdriver
in place push the drawer
closed.The screwdriver
will push against the end
panel and extend the
drawer runner .
K
A
C
B
K
K
D
K
2nd hole
e: Pull drawer out slowly
and line the hole in the
drawer side with the 2nd
threaded hole in the
runner . Now insert
bolts through the
drawer side and
into threaded hole in
runner .
f: Now insert bolts
through the drawer side
and into threaded hole in
runner .
K
H
K
l
H
K
E
F
I
H
K
2nd hole
14
Assembly Instructions
Step 16
Fixing to wall
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
L
x1
E
x2
With help move the
unit into position.
Warning:
2 people to lift.
Lift with care.
Warning:
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
15
Congratulations! Your unit is complete.
Assembly Instructions
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
8am - 4.30pm (Monday to Thursday)
0845 061 3967
01709 534123
(by contacting the customer service line your statutory rights are not affected)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
8am - 2.30pm (Fridays)
You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
Notes
Notes
Notes
Loading...