Argos 1834402 ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 50cm

Depth - 59.5cm

Height - 212.5cm

Atlas - Single Robe Carcass

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 05/02/14

Important - Please read these instructions fully before starting assembly

152/9432

157/9107

157/2537

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 34kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Universal End (D2396A)

(2074 x 591mm) x 2

Top/Base (D2399A)

(500 x 592mm) x 2

Fixed Shelf (D2401A)

(468 x 590mm)

Back (X2100-494)

(2100 x 494mm)

Hanging Rail (FHR460)

(460mm long) x 2

4 5

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 2

Metal dowel (F901) x 4

D E

Large locking nut (F900) x 4

G H I

Nail (F51) x 33

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Rail Holder (F891) x 4

Allen Key (F36) x 1

50mm Screw (F49) x 12

19mm Screw (F461) x 2

25mm Screw (F50) x 4

13mm Screw (F63) x 16

13mm Screw (F79) x 1

Bracket (F327) x 1

Feet (F854) x 4

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

100

Handle (F323) x 1 Hinge (F328) x 4

Finished

front edge

Prepare the left end

Refer to step 1 and, if you have chosen to fit 1 hanging rail or, an internal chest or, a shelf pack, screw 2

metal dowels into the left end .

Note: Tighten the metal dowels up fully against the panels.

Note: If you have purchased a shelf pack, do not fit the rail holder.

To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that it is fitted straight, in line with the panel edges and then fit another screw

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Are you fitting 1 or 2 Hanging Rails or, an Internal Chest or, a Shelf Pack?

Step 1

Step 2

The fixed shelf will

need to go here if

you are fitting the

following:-

Only 1 Hanging Rail

An Internal Chest

A Shelf Pack

Follow Steps

2 and 3.

Only follow Steps 2 and 3 if you are only fitting

1 hanging rail or, an internal chest or, a shelf pack.

If you are fitting 2 hanging rails, follow Step 4 and 5.

The fixed shelf will need to go

here if you are

fitting the

following:-

2 Hanging Rails

Follow Steps

4 and 5.

Note: If you have purchased a shelf pack,

do not fit the rail holder.

Assembly Instructions

Step 3

Step 4

Prepare the right end

Refer to step 1 and, if you have chosen to fit 1 hanging rail or, an internal chest or, a shelf pack, screw 2

metal dowels into the right end .

Note: Tighten the metal dowels up fully against the panels.

To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the right end . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Finished

front edge

Finished

front edge

Prepare the left end

Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2

metal dowels into the left end .

Note: Tighten the metal dowels up fully against the panels.

To fit the 2 rail holders screw through the top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that they are fitted straight, in line with the panel edges and then fit another screw using the lower hole.

Only follow Steps 4 and 5 if you are fitting 2 hanging rails.

If you are just fitting 1 rail, follow Step 2 and 3.

Note: If you have purchased a shelf pack,

do not fit the rail holder.

Only follow Steps 2 and 3 if you are only fitting

1 hanging rail or, an internal chest or, a shelf pack.

If you are fitting 2 hanging rails, follow Step 4 and 5.

+ 14 hidden pages