Argos 1816853 ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 47.5cm
Depth - 40cm
Height - 48cm
Atlas - Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 11/03/14
Important - Please read these instructions fully before starting assembly
145/3900
159/7206
166/2533
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 13.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
Top (D2379A)
(473 x 396mm)
Large Drawer Front (D2383A)
(475 x 264mm)
Left Side (D2380A)
(461 x 395mm)
Right Side (D2381A)
(461 x 395mm)
Rail (D2382A)
(441 x 60mm) x 2
7
Small Drawer Front (D2388A)
(475 x 189mm)
6
Small Left Drawer Side (W370-124LH)
(370 x 124mm)
Small Right Drawer Side (W370-124RH)
(370 x 124mm)
8
Large Left Drawer Side (W370-165LH)
(370 x 165mm)
Large Right Drawer Side (W370-165RH)
(370 x 165mm)
Small Wrap Back (W391-124)
(391 x 124mm)
Large Wrap Back (W391-165)
(391 x 165mm)
Back (X453-467)
(453 x 467mm)
Drawer Base (T402-367)
(402 x 367mm) x 2
9
10 11 12
13 14
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 12
C
D E
Large locking nut (F900) x 8
F
G H I
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
19mm Screw (F461) x 4
13mm Screw (F52) x 12
13mm Screw (F63) x 12 Nail (F51) x 13
Knock-in Peg (F171) x 8
J
R Runner (F160) x 2
b
L Runner (F161) x 2
J
c
L Runner (F159) x 2
J
a
R Runner (F162) x 2
J
d
350mm long
Handle (F266) x 2
K
304mm
L
Wedgefix (F639) x 8
M
Plastic Nail (F91) x 4
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
D
Step 2
Prepare the small drawer front
Screw 2 metal dowels into the holes shown on the back of the small drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the small drawer sides
Insert a small locking nut into the hole shown on the small left drawer side and small right drawer side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
D
7
8
Attach the drawer sides to the drawer front
Push the small left drawer side and small right drawer side . . onto the back of the small drawer front .
Turn the small locking nuts on the small left drawer side and small right drawer side . .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
8
7
8
5
D
D
7
8
Groove
7
D
D
B
B
5
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.
D
8
7
5
5
Assembly Instructions
5
Step 4
I
I
Fit the drawer base
Slide the drawer base down the grooves in the small drawer sides and and down into the groove in the small drawer front .
Step 5
Fit the small drawer back
Fit the small drawer back . between the small drawer sides and .
Make sure that the drawer base fits into the groove in the small drawer back .
Hold the small drawer back in position and tap the knock-in pegs through the holes in the small drawer sides and .
Step 6
13
7
8
5
9
7 8
13
9
9
I
7
8
Attach the handle
Attach a handle to the small drawer front using 2 screws .
K
E
5
8
I
I
13
7
8
9
7
8
13
E
E
K
5
Assembly Instructions
6
Step 7
Fit runners to the small drawer
Turn the small drawer assembly over.
Fit runner , marked with ‘R’, to the bottom edge of the small right drawer side , as shown, making sure that it is pushed up against the back of the small drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the small left drawer side using the same method.
7
J d
8
5
G
J c
J d
Runners must be
pushed up against
the drawer front
R
R
G
G
L
J c
L
G
G
7
8
5
B
Prepare the large drawer front
Screw 2 metal dowels into the holes shown on the back of the large drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
6
B
B
6
Step 9
Step 8
Fit 4 wedgefixes
Turn the drawer over.
Slide 4 wedgefixes into the small grooves on the drawer assembly and tighten up the screws.
L
L
L
L
L
L
Fit the drawer base
Slide the drawer base down the grooves in the large drawer sides and and down into the groove in the large drawer front .
10
11
Assembly Instructions
7
Step 10
Step 12
Prepare the large drawer sides
Insert a small locking nut into the hole shown on the large left drawer side and large right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
10
11
D
D
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
D
6
11
B
B
D
Step 11
Attach the drawer sides to the drawer front
Push the large left drawer side . and large right drawer side . onto the back of the large drawer front .
Turn the small locking nuts on the large left drawer side and large right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10
11
6
D
D
11
10
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.
6
Groove
10
11
13
10
11
6
6
11
10
13
I
I
Assembly Instructions
8
Step 13
6
11
10
13
12
Fit the large drawer back
Fit the large drawer back . between the large drawer sides and .
Make sure that the drawer base fits into the groove in the large drawer back .
Hold the large drawer back in position and tap the knock-in pegs through the holes in the large drawer sides and .
12
10 11
13
12
12
I
10
11
I
I
Step 14
Attach the handle
Attach a handle to the large drawer front using 2 screws .
Step 15
K
E
6
E
E
K
6
Fit 4 wedgefixes
Turn the drawer over.
Slide 4 wedgefixes into the small grooves on the drawer assembly and tighten up the screws.
L
L
L
L
L
L
Assembly Instructions
9
Step 16
Step 17
Fit runners to the large drawer
Turn the large drawer assembly over.
Fit runner , marked with ‘R’, to the bottom edge of the large right drawer side , as shown, making sure that it is pushed up against the back of the large drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the large left drawer side using the same method.
10
J d
11
6
G
J c
J d
Runners must be
pushed up against
the drawer front
R
R
L
J c
L
G
G
10
11
6
G
G
Prepare the top
Screw 4 metal dowels into the top .
B
B
B
B
Plain chipboard
surface
3
B
3
Finished
front edge
Assembly Instructions
10
Step 18
A
Finished front edge
a:
Finished
front edge
b:
J a
F
Finished front edge
F
1st screw
2nd screw
F
3rd screw
F
J a
F
F
J a
Finished front edge
G
G
G
C
C
C
B
B
F
J a
F
F
Prepare the left side
a: Fit runner to the
left side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
Screw 2 metal dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
J a
1
F
F
G
J a
B
1
C
1
10mm
A
A
1
1
1
Assembly Instructions
11
Step 19
Finished
front edge
Step 20
Fit the top to the right side
Push the top onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
2
3
C
C
C
B
2
2
3
Finished
front edge
A
J b
F
Finished front edge
F
1st screw
2nd screw
F
3rd screw
J b
Finished front edge
G
F
F
J b
F
F
F
J b
F
Finished
front edge
Prepare the right side
a: Fit runner to the
right side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
Screw 2 metal dowels into the right side .
Insert 2 large locking nuts into the right side .
Tap a wooden dowel into the right side .
J b
2
F
F
G
J b
B
2
C
2
2
Finished
front edge
2
G
G
a:
b:
C
C
A
2
B
B
Assembly Instructions
12
Step 21
A
C
C
A
Prepare the 2 rails
Tap 2 wooden dowels into each of the 2 rails .
Insert 2 large locking nuts into each of the 2 rails .
A
x 2
4
C
4
4
Plain chipboard
surface
Step 22
Fit the 2 rails
Push the 2 rails onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the rails .
2
4
C
4
Step 23
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and the 2 rails .
1
C
1
4
4
4
4
4
1
2
Assembly Instructions
13
Step 24
Step 25
y
y
x
x
b:
H
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
14
H
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
14
14
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
M
1
2
M
M
M
M
1
2
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 26
Fit the drawers
Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.
Assembly is complete
Side
panel
Drawer
Small Drawer
Large Drawer
ALR2952
MADE IN
BRITAIN
Dimensions
Width - 79.5cm
Depth - 41.5cm
Height - 86cm
Atlas - 4 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 11/03/14
Important - Please read these instructions fully before starting assembly
181/6815
171/5129
146/7233
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 31kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
2
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4
5
Top (D2389A)
(793 x 396mm)
Large Drawer Front (D2394A)
(795 x 264mm)
Left Side (D2390A)
(845 x 395mm)
Right Side (D2391A)
(845 x 395mm)
Rail (D2392A)
(761 x 60mm) x 3
7
Small Drawer Front (D2393A)
(795 x 189mm) x 3
6
Small Left Drawer Side (W370-124LH)
(370 x 124mm) x 3
Small Right Drawer Side (W370-124RH)
(370 x 124mm) x 3
8
Large Left Drawer Side (W370-165LH)
(370 x 165mm)
Large Right Drawer Side (W370-165RH)
(370 x 165mm)
Small Wrap Back (W711-124)
(711 x 124mm) x 3
Large Wrap Back (W711-165)
(711 x 165mm)
Back (X836-787)
(836 x 787mm)
Drawer Base (T722-367)
(722 x 367mm) x 4
9
10 11 12
13
14
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 18
C
D E
Large locking nut (F900) x 10
F
G H I
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 8
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
19mm Screw (F461) x 8
13mm Screw (F52) x 24
13mm Screw (F63) x 24 Nail (F51) x 22
Knock-in Peg (F171) x 16
J
R Runner (F160) x 4
b
L Runner (F161) x 4
J
c
L Runner (F159) x 4
J
a
R Runner (F162) x 4
J
d
350mm long
Handle (F227) x 4
K
623mm
M
L
Bracket (F327) x 1
13mm Screw (F79) x 1
N
Wedgefix (F639) x 16
O
Plastic Nail (F91) x 4
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
5
8
B
B
D
Step 2
Prepare the small drawer fronts
Screw 2 metal dowels into the holes shown on the back of each small drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the small drawer sides
Insert a small locking nut into the hole shown on each small left drawer side and small right drawer side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
D
7
8
Attach the drawer sides to the drawer fronts
Push the small left drawer sides and small right drawer sides . . onto the back of the small drawer fronts .
Turn the small locking nuts on the small left drawer sides and small right drawer sides . .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
8
7
8
5
D
D
7
8
Groove
7
D
D
B
B
5
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.
D
8
7
x 3
x 3 x 3
x 3
5
5
5
Step 4
I
I
Fit the drawer bases
Slide the drawer base down the grooves in the small drawer sides and and down into the groove in the small drawer fronts .
Step 5
Fit the small drawer backs
Fit the small drawer back . between the small drawer sides and .
Make sure that the drawer base fits into the groove in the small drawer back .
Hold the small drawer back in position and tap the knock-in pegs through the holes in the small drawer sides and .
Step 6
13
7
8
5
9
7 8
13
9
9
I
7
8
Attach the handles
Attach handles to the small drawer fronts using 2 screws .
K
E
5
8
I
I
13
7
8
9
7
8
13
E
E
K
5
x 3
x 3
x 3
Assembly Instructions
6
Step 7
Fit runners to the small drawers
Turn the small drawer assemblies over.
Fit runner , marked with ‘R’, to the bottom edge of the small right drawer side , as shown, making sure that it is pushed up against the back of the small drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the small left drawer side using the same method.
7
J d
8
5
G
J c
J d
Runners must be
pushed up against
the drawer front
R
R
G
G
L
J c
L
G
G
7
8
5
B
Prepare the large drawer front
Screw 2 metal dowels into the holes shown on the back of the large drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
6
B
B
6
Step 9
Step 8
Fit the wedgefixes
Slide 2 wedgefixes into the small groove located on the back of the drawer front and 2 into the small groove in
the drawer back .
Once in place, tighten up the screws in the wedgefixes .
N
5
9
N
5
N
N
N
N
9
x 3
x 3
x 1
Fit the drawer base
Slide the drawer base down the grooves in the large drawer sides and and down into the groove in the large drawer front .
10
11
Assembly Instructions
7
Step 10
Step 12
Prepare the large drawer sides
Insert a small locking nut into the hole shown on the large left drawer side and large right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
10
11
D
D
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
D
6
11
B
B
D
Step 11
Attach the drawer sides to the drawer front
Push the large left drawer side . and large right drawer side . onto the back of the large drawer front .
Turn the small locking nuts on the large left drawer side and large right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
10
11
6
D
D
11
10
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the groove is on the inside, as shown.
6
Groove
10
11
13
10
11
6
6
11
10
13
I
I
Assembly Instructions
8
Step 13
Fit runners to the large drawer
Turn the large drawer assembly over.
Fit runner , marked with ‘R’, to the bottom edge of the large right drawer side , as shown, making sure that it is pushed up against the back of the large drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the large left drawer side using the same method.
10
J d
11
6
G
J c
J d
Runners must be
pushed up against
the drawer front
R
R
G
G
L
J c
L
G
G
10
11
6
6
11
10
13
12
Fit the large drawer back
Fit the large drawer back . between the large drawer sides and .
Make sure that the drawer base fits into the groove in the large drawer back .
Hold the large drawer back in position and tap the knock-in pegs through the holes in the large drawer sides and .
12
10 11
13
12
12
I
10
11
I
I
Step 14
Attach the handle
Attach a handle to the large drawer front using 2 screws .
Step 15
K
E
6
E
E
K
6
Assembly Instructions
9
Step 16
Step 17
Prepare the top
Screw 4 metal dowels into the top .
B
B
B
B
Plain chipboard
surface
3
B
3
Finished
front edge
6
Fit the wedgefixes
Slide 2 wedgefixes into the small groove located on the back of the drawer front and 2 into the small groove in
the drawer back .
Once in place, tighten up the screws in the wedgefixes .
N
6
12
N
N
N
N
N
12
Fix a bracket to the top .
The bracket must be flush against the back edge.
Secure the bracket using screw .
M
L
L
L
3
L
L
M
Assembly Instructions
10
Step 18
Finished front edge
a:
Finished
front edge
b:
J a
F
Finished front edge
F
1st screw
2nd screw
F
3rd screw
J a
Finished front edge
G
C
B
F
J a
F
F
Prepare the left side
a: Fit runner to the
left side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
Screw 3 metal dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Tap a wooden dowel into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
J a
1
F
F
G
J a
B
1
C
1
10mm
A
A
1
1
F
J a
F
F
F
J a
F
F
F
J a
F
F
1
B
B
G
G
A
C
C
G
G
Assembly Instructions
11
Step 19
J b
F
Finished front edge
F
1st screw
2nd screw
F
3rd screw
J b
Finished front edge
G
F
F
J b
F
Finished
front edge
Prepare the right side
a: Fit runner to the
right side .
The 1st screw uses the 2nd hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
Screw 3 metal dowels into the right side .
Insert 2 large locking nuts into the right side .
Tap a wooden dowel into the right side .
J b
2
F
F
G
J b
B
2
C
2
2
a:
b:
A
2
B
F
F
J b
F
F
F
J b
F
F
F
J b
F
Finished
front edge
2
B
B
A
C
C
G
G
G
G
A
Assembly Instructions
12
Step 20
C
C
A
Prepare the 3 rails
Tap 2 wooden dowels into each of the 3 rails .
Insert 2 large locking nuts into each of the 3 rails .
A
x 3
4
C
4
4
Plain chipboard
surface
Step 22
Fit the 3 rails
Push the 3 rails onto the right side .
Use a screwdriver to tighten the 3 large locking nuts fitted to the rails .
2
4
C
4
Finished
front edge
Step 21
Fit the top
Push the top onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
2
3
C
C
C
B
2
2
3
Finished
front edge
2
4
4
4
y
y
Assembly Instructions
13
Step 23
b:
H
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
14
H
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
14
Step 24
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 5 large locking nuts fitted to the left side and the 3 rails .
1
C
1
4
4
4
4
4
4
x
x
14
Assembly Instructions
Step 25
Step 26
L
Secure unit to a wall
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the metal bracket fitted under the top plinth.
Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.
Warning: Take
care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
WALL
WALL
Top of unit
L
L
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
O
1
2
4
O
O
O
O
1
2
14
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 27
ALR2953
Fit the drawers
Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.
Assembly is complete
Side
panel
Drawer
Large Drawer
MADE IN
BRITAIN
Dimensions
Atlas - Double Robe Carcass
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 05/02/14
Important - Please read these instructions fully before starting assembly
157/3309
152/7458
151/4739
Width - 100cm
Depth - 59.5cm
Height - 212.5cm
There is the option of
purchasing an Internal 3
Drawer Chest that can be
placed inside your Robe
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 49kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
Universal End (D2396A)
(2074 x 591mm) x 2
2
3
Hanging Rail (FHR960)
(960mm long) x 2
4
Top/Base (D2395A)
(1000 x 592mm) x 2
Fixed Shelf (D2397A)
(968 x 590mm)
5
Back (X2100-994)
(2100 x 994mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 4
C
D E
Large locking nut (F900) x 4
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
Rail Holder (F891) x 4
Allen Key (F36) x 1
50mm Screw (F49) x 12
19mm Screw (F461) x 4
Handle (F323) x 2 Hinge (F328) x 8
25mm Screw (F50) x 6
13mm Screw (F63) x 24
13mm Screw (F79) x 2
Bracket (F327) x 2
Feet (F854) x 6
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Finished
front edge
Prepare the left end
Refer to step 1 and, if you have chosen to fit 1 hanging rail, screw 2
metal dowels into the left end .
Note: Tighten the metal dowels up fully against the panels.
To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
Are you fitting 1 or 2 hanging rails or, a shelf pack?
Step 2
If you are just
fitting 1 hanging
rail, the fixed
shelf will need
to go here.
Follow Steps 2
and 3.
Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
If you are fitting 2 hanging rails, the
fixed shelf will
need to go here.
Follow Step 4
and 5.
J
K
J
K
B
K
J
B
B
1
1
B
K
1
J
Assembly Instructions
5
Step 3
Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
Step 4
Prepare the right end
Refer to step 1 and, if you have chosen to fit 1 hanging rail, screw 2
metal dowels into the right end .
Note: Tighten the metal dowels up fully against the panels.
To fit the rail holder , screw through its top hole with screw and into the shallow mark hole drilled in the right end . Make sure that it is fitted straight, in line with the panel edges and then fit another screw using the lower hole.
B
K
J
J
1
1
B
B
K
1
Finished
front edge
Finished
front edge
Prepare the left end
Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2
metal dowels into the left end .
Note: Tighten the metal dowels up fully against the panels.
To fit the 2 rail holders screw through the top hole with screw and into the shallow mark hole drilled in the left end . . Make sure that they are fitted straight, in line with the panel edges and then fit another screw using the lower hole.
B
K
J
J
B
B
1
1
J
K
J
K
B
K
1
K
Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
J
K
J
K
A
Assembly Instructions
6
Step 5
Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
B
B
K
1
Finished
front edge
Prepare the right end
Refer to step 1 and, if you have chosen to fit 2 hanging rails, screw 2
metal dowels into the right end .
Note: Tighten the metal dowels up fully against the panels.
To fit the 2 rail holders screw through the top hole with screw and into the shallow mark hole drilled in the right end . Make sure that they are fitted straight, in line with the panel edges and then fit another screw using the lower hole.
B
K
J
J
1
1
J
K
J
K
B
K
Step 6
Prepare the fixed shelf
Tap 2 wooden dowels into the fixed shelf .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into the fixed shelf .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
A
C
3
3
C
10mm
A
C
C
A
C
C
3
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 7
Step 8
Join the fixed shelf to the right side
Push the fixed shelf onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the fixed shelf .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
B
C
3
1
1
3
C
C
3
Fit the left side
Push the left side onto the fixed shelf .
Use a screwdriver to tighten the 2 large locking nuts fitted to the fixed shelf .
1
3
C
3
Finished
front edge
1
3
If you have fitted the
2 metal dowels in this
position, the fixed
shelf will go here.
The following diagrams will show the fixed
shelf at the top end of the unit.
You may have fitted it in the middle of the unit.
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
Step 10
Fit the base
Attach the base to the ends using 6 screws and tighten them using the allen key . .
Prepare the base
Screw the 6 feet into the shallow mark holes on the base using screws .
M
2
G
2
1
F
E
G
M
M
M
M
M
M
Finished
front edge
E
F
F
F
F
F
F
2
1
1
2
y
Assembly Instructions
9
Step 11
Step 12
F
F
F
2
E
F
F
F
Finished
front edge
1
1
Fit the top
Attach the top to the ends using 6 screws and tighten them using the allen key .
2
1
F
E
2
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
5
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
5
Warning: The unit is heavy. Lift with care.
y
y
x
b:
D
5
Unit colour on
the top surface
x
Assembly Instructions
10
Step 13
Top of Unit
WALL
WALL
Back of Unit
Fit the 2 brackets
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the 2 brackets fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screws will depend on the distance from the back of the unit to the wall.
Fix the brackets loosely onto the top of the unit using screws and mark the wall for the wall fixing.
Swivel the brackets away from the wall and drill the holes in the wall using a suitable drill bit and fit your wall fixings.
Swivel the brackets back and fix the brackets to the wall, then tighten the screws .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The unit is heavy. Lift with care.
L
L
I
L
L
I
L
L
I
L
L
NOTE
The unused fittings from this assembly are used to fit the doors.
Please refer to the instructions packed with the doors.
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
The unit must be level and square
before fitting the brackets.
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2955
Step 14
Step 15
4
K
Fit the hanging rail(s)
Push the hanging rail(s) . into the rail holders fitted to the side panels.
4
K
4
Fit the doors and, if required, the internal chest
Please refer to the instructions packed with the doors or chest.
Chest
Door
MADE IN
BRITAIN
Dimensions for each door
Width - 49.5cm
Depth - 1.5cm
Height - 210cm
Atlas - Standard Double Door
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 17/11/14
Important - Please read these instructions fully before starting assembly
151/7396
157/7240
157/2063
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: These panels weigh approximately 22kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Component - Panel
Please check you have the panel listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Standard Door (D2398A)
(2100 x 495mm) x 2
These fittings are packed with the Robe Carcass. The quantities will depend on which robe you have bought.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
H
O
J N
19mm Screw (F461)
Handle (F328)
Hinge (F328)
13mm Screw (F63)
Assembly Instructions
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Have you purchased a Mirror Door?
90
J
J
O
J
J
O
J
J
O
J
J
O
Prepare the doors
Push fit 4 hinges into each door.
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
J
O
IMPORTANT
If you have purchased a Mirror Door,
DO NOT follow these instructions.
Please use the instructions packed
with the Mirror Door.
Assembly Instructions
4
Step 3
For a door which has a handle on the left, drill these 2 handle holes
Important: Please follow these instructions carefully.
Lay the door down onto a smooth surface.
Check that the hinges and holes are in the same place as the diagram.
Note: We recommend the use of a small piece of waste wood, placed behind the holes while drilling, to reduce the possibility of any breakout.
Using the pilot holes in the rear face of the door, drill through the 2 holes indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.
IMPORTANT
This step shows which handle holes to drill for doors
that have their handles on the LEFT, as shown below.
Go to Step 4 for how to drill a
door with its handle on the RIGHT.
ONLY drill these 2 holes
Small piece of
waste wood
Small piece of
waste wood
Assembly Instructions
5
Step 4
Small piece of
waste wood
Small piece of
waste wood
IMPORTANT
This step shows which handle holes to drill for doors
that have their handles on the RIGHT, as shown below.
Go to Step 3 for how to drill a
door with its handle on the LEFT.
For a door which has a handle on the right, drill these 2 handle holes
Important: Please follow these instructions carefully.
Lay the door down onto a smooth surface.
Check that the hinges and holes are in the same place as the diagram.
Note: We recommend the use of a small piece of waste wood, placed behind the holes while drilling, to reduce the possibility of any breakout.
Using the pilot holes in the rear face of the door, drill through the 2 holes indicated opposite, using a 2.5mm diameter drill.
Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.
ONLY drill these 2 holes
Assembly Instructions
6
Step 5
Fit the doors and the handles
2 people are needed here
Make sure that the doors are the correct way around. The bottom hole on the back surface of the door will be one of holes that you have drilled.
Line up the 2 screws in the top hinge with the 2 holes at the top of the panel and push them in.
Working down the door, push in the other hinges.
When all of the hinges have been pushed into place, tighten the 2 screws on each hinge.
Attach a handle to each door using 2 screws .
This shows a door being fitted onto the right side of a double robe. The same assembly method applies to all doors and robes.
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
O O
Warning: The door is heavy. Lift with care.
O
N
H
H
H
N
Note: Fit the top hinge 1st
Assembly Instructions
7
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2961
Step 6
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Loading...