Hamlin- 3 Doors Robe
Assembly Instructions - Please keep for future reference
h y g e n a
152/4877
151/4203
152/9614
Dimensions
Width - 120cm
Depth - 55,8cm
Height - 192cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 28/10/13
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/driversfor
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note:If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
Please check you have all the panels listed below
Right side panel
1
top
Left side panel
2
Middle wall panel
3
(190 x 54cm)
(190 x 54cm)
(178.8 x 54cm)
top
top
Top panel
9
Base panel (117 x 54cm)
10
underside
(120 x 55.8cm)
underside
Door x 3
4
Door knocker x 3
5
Left back panel x 2 (180.8 x 39.1cm)
6
Right back panel (180.8 x 40cm)
7
(179 x 35cm)
(178 x 8cm)
Left shelf
11
underside
Right shelf
12
Bottom frame
13
Unfinished bottom frame(117 x 9.6cm)
14
Left hanging rail
15
(77 x 52.7cm)
(38.5 x 52.7cm)
(117 x 9.6cm)
(76.2 x 3cm)
8
H profile
(179 x 1.8cm)
Right hanging rail
16
(37.7 x 3cm)
2
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B
Ø 6X30 Wooden dowel x 24
Ø 6X50 Wooden dowel x 2
D E F
16mm Screw x 114mm Screw x 36
Locking
Metal dowel x 20
J
nut x 20
K
Plastic
Nail x 6
feet x 6
M
Hanging rail
support x 4
P
Bracket x 18
Washer x 2
Q
Wall strap x 1
C
14mm Screw x 32
25mm Screw x 21
IG H
Nail x 94
L
L shaped
bracket x 6
ON
Plastic
x 20
cap
R
Door
hinge x 9
Tools required
Phillips screwdriver
(small & medium)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Assembly Instructions
Step1
Insert dowels into the
A
indicated parts.
Fix hanging rail support
M
in the pre marked
holes on right side panel
1
and left side panel
2
using screws , as
C
shown.
C
M
1
and
A
2
3
10
A
A
A
Step2
Insert dowels and
into right shelf as
shown.
A
12
A
A
Finished edge.
A
B
11
13
14
A
A
A
Finished edge.
12
B
A
B
4
Assembly Instructions
Step3
a:
Fitting hinges.
Loosen screw in door
a:
hinge and separate
the ‘back plate’.
R
R
R
R
b:
2
D
R
b:Attach ‘back plates’
in the pre marked holes
on right and left side
panels and using
screws .
1
D
Attach ‘back plates’ in
the pre marked holes on
middle wall panel
using screws .
2
R
3
D
R
R
R
1
R
R
R
3
R
R
5
Assembly Instructions
Step4
Fitting Metal dowels.
G
G
Screw metal dowels
into right side panel ,
left side panel , top
10
9
.
panel and base panel
G
1
2
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
Step5
1
and
G
G
G
10
2
G
9
G
Fitting Metal dowels and
hanging rail support.
Fix hanging rail support
M
in the pre marked
holes on both sides of
middle wall panel
using screws , as
3
C
shown.
Screw metal dowels
G
into both sides of middle
wall panel .
3
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
G
3
G
O
G
3
180
G
C
M
C
M
6
Assembly Instructions
Step6
Fixing L shaped
brackets.
Fix L shaped brackets
in the bottom frame
and unfinished bottom
frame using screws
14
C
, as shown.
Attention:
Leave gap1mm
from the edge of the
bars as shown.
Fix L shaped brackets to
the unfinished side in
bottom frame .
13
13
Attention:
Unfinished side
to face up.
L
13
L
14
C
L
L
L
13
L
1mm
L
14
Step7
Fixing base panel.
With help, f
10
to middle wall panel
3
.
In 2sert locking nuts
into middle wall panel
where shown.
e a screwdriver to turnUs
locking nuts ockwisecl
to lock.
Do not over tighten.
it base panel
H
L
Painted side
H
3
H
10
to face up.
After screwing locking
nuts, insert plastic caps
O
.
7
H
H
O
Assembly Instructions
Step8
Fixing shelves.
With help, f
and right shelf to
it left shelf
12
middle wall panel .
Attention!
Right shelf with
longer wooden
dowel should be fitted on
the right side and painted
edge on shelves to be
facing up.
In 4sert locking nuts
into ere shown.shelfs wh
e a screwdriver to turnUs
locking nuts ockwisecl
H
to lock.
Do not over tighten.
11
3
H
Finished edges
to face up
11
Attention!
12
12
H
3
H
B
After screwing locking
nuts, insert plastic caps
O
.
Step9
Fixing right side panel.
Place right side panel
properly ensuring dowels
are all fitted into their
holes at the same time.
I 4 lnsert ocking nuts
into b nelase pa and right
shelf where shown.
Use a screwdriver to turn
locking nuts lockwisec
H
to lock.
Do not over tighten.
1
H
H
H
H
O
1
H
After screwing locking
nuts, insert plastic caps
O
.
H
H
O
8
Assembly Instructions
Step10
Fixing left side panel.
Two people are required
for an easier assembly.
Fit bottom frames and
14
and then, place left
side panel properly
2
ensuring dowels and
bottom frames are all
fitted into their holes at
the same time.
Make sure bottom frames
14
and are positioned
13
as indicated in the
picture.
13
H
H
O
I 4 lnsert ocking nuts
H
into b nelase pa and shelf
where shown.
Use a screwdriver to turn
locking nuts lockwisec
H
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
O
.
Fix bottom frames and
14
in the side panels and
13
base panel through L
shaped brackets using
screws .
C
L
H
Finished side
to face up
2
H
H
13
L
14
L
L
C
9
Assembly Instructions
Step11
Fixing top panel.
With help, f
it top panel
to the cabinet.
In 6sert locking nuts
H
into elside pan s and
middle wall panel where
shown.
e a screwdriver to turnUs
locking nuts ockwisecl
H
to lock.
Do not over tighten.
After screwing locking
nuts, insert plastic caps
O
.
9
H
H
9
H
H
O
10
Assembly Instructions
Step12
Attach plastic feet.
Attach p in
lastic feet
the bottom edge
K
of the
side panels and bottom
frames using nails .
J
Make sure nails
are fully nailed.
After attaching plastic
feet, with help, carefully
stand the product upright.
K
J
K
K
Step13
Insert hanging rails
16
and into the supports
M
.
15
K
16
15
M
11
Assembly Instructions
Step14
Fixing back panels.
Important:
Cabinet be
‘square’ when back panels
are attached. Make sure
back panels are in flush
with the edge of the top
panel prior to fixing.
a: Attach the left back
panel first using nails
Note:
Back panel´s finished
side to face inside.
6
I
.
MUST
6 6
8
I
b: Position profile
8
onto back panel
(just attach).
c: Carefully slot the
second back panel into
the profile and fix it to the
cabinet using nails .
6
I
d: Attach right back
panel using nails .
7
I
P
I
8
P
6
6
7
I
P
e:Attach brackets ,
ensuring it is placed part
over panel and part over
base panel using nails
I
.
6
7
P
I
7
P
6
I
12
Assembly Instructions
Step15
Fitting hinges to doors.
Insert hinges in the
a:
holes on door , as
shown.
Attach hinges in the
b:
the door using screws ,
as shown.
Repeat step 15 for the
other doors.
R
4
R
D
a: b:
R
R
4
R
D
D
R
Step16
Hanging doors.
a:With help, slot door
hinges onto ‘hinge
plates’.
b:Tighten screw shown
to lock hinges in position.
Repeat and for
other doors.
See ‘hinge adjustment’ in
step 18 if the doors need
adjusting.
R
a b
a:
R
4
4
b:
4
R
13
Assembly Instructions
Step17
Fixing door knocker.
ttach door knocker in
A
the pre marked holes on
door using screws as
shown. Make sure
knocker is aligned at top
of door before fixing.
Repeat step 17 for the
other doors.
5
F
Please note!
Edges of painels
must line up at
this end.
F
5
5
Step18
Hinge adjustment.
a:
To move doors up or
down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
b:
To move doors in or
out: loosen screw shown
and move doors to suit.
Re-tighten screws.
a:
b:
Continued on next page.
14
Assembly Instructions
Step -18 continued
c: To move doors left or
right: loosen screw shown
and move doors to suit.
Re-tighten screws.
Step19
Fixing to wall.
Furniture must befixed to
a wall. Fix wall strap to
top of furniture using
washer and screw .
With help, move furniture
into position.
N E
Q
c:
N
wall
E
Q
Note:Wall plugs not supplied.
The correct type of fixing must
be used for your wall, seek
professional advice if in doubt.
Assembly is complete.
N
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
15
A Guide to -Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2:Ensure you use the recommended drill bit to match the wall
plug and hole size.
3:Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4:Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
No.1“General Purpose” wall plug No.3“Cavity Fixing” wall plug No.5“Hammer Fixing” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2“Plasterboard” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4“Cavity Fixing-Heavy Duty”
wall plug
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
No.6“Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety:Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting:From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Loading...