Argos 1458259 ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 5 - 21/01/15
Important - Please read these instructions fully before starting assembly
147/1999
157/6760
145/7229
Atlas - Triple Robe Carcass
Width - 150cm
Depth - 59.5cm
Height - 212.5cm
IMPORTANT
The unit MUST be fixed to a wall using both
of the overbalance protector kits supplied.
There is the option of
purchasing an Internal 3
Drawer Chest that can be
placed inside your Robe
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 65kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using both of
the overbalance protector kits
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Universal End (D2396A)
(2074 x 591mm) x 2
5
2
Top/Base (D2652A)
(1499 x 592mm) x 2
Large Fixed Shelf (D2397A)
(968 x 590mm)
Upright (D2653A)
(2074 x 591mm)
4
3
Small Fixed Shelf (D2654A)
(484 x 590mm)
Small Back (X2100-504)
(2100 x 504mm)
Large Back (X2100-988)
(2100 x 988mm)
Large Hanging Rail (FHR960)
(960mm long) x 2
7
Small Hanging Rail (FHR476)
(476mm long) x 2
6
8 9
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 8
C
D E
Large locking
nut (F900) x 8
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
Rail Holder
(F891) x 8
Allen Key (F36) x 1
50mm Screw (F49) x 18
19mm Screw (F461) x 6
Hinge (F328) x 12
25mm Screw (F50) x 6
13mm Screw (F63) x 38
Feet (F854) x 6
P
Handle (F323) x 3
Nail screw (F277) x 6
Back holder (F276) x 6
* These can also be round
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 2
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Are you fitting 1 or 2
hanging rails or, a
shelf pack?
If you are just
fitting 1
hanging rail to
this side, the
large fixed
shelf will need
to go here.
If you are just
fitting 1
hanging rail or
the shelf pack
to this side,
the small fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the large fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the small fixed
shelf will need
to go here.
Finished
front edge
Assembly Instructions
5
Step 2
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
2
2
J
K
J
K
B
Refer to Step 1 and ONLY FOLLOW THIS STEP if you
are fitting the small fixed shelf near the top of the unit.
Note: If you have purchased a
shelf pack, do not fit the rail holder.
B
B
K
Turn the upright over and
carry out either step 4 or 5
2
Please ensure you have your panel in exactly the
same orientation as the picture above and use the
2 inside holes for screws B as shown in the picture.