Maddison bunk
Important - Please read these instructions fully before starting assembly
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 -24/10/13
171/5882
Assembly Instructions - Please keep for future reference
Length - 200cm
Width - 97.5cm
Height - 170cm
145/3199
145/9179
Important - Please read these instructions fully before starting assembly
Mattress height safety notice
Important
1) Please note the maximum mattress height is indicated on the corner post inside the opening at the
top of the ladder.
2) This is legal requirement and it is vital that the mattress does not exceed this mark.
3) Maximum thickness of the mattress is 20cm:The top of the mattress shall not come above the line
marked on the bed.
4) All assembly fixings should always be tightened properly.Take care to ensure that no fixings are
loose.
5) Recommended size of the mattress for the both bunks is 90×190cm.
6) The bunk bed should not be used if any structural part is broken or missing.
7) Warning: High beds and the upper bed of bunk beds are not suitable for children under six years
due to the risk of injury from falls.
8) Children can strangle in items such as ropes, strings, cords, harnesses and belts attached to or
hung on a bunk bed.
Warning
1) Children can become trapped between the bed and wall. To avoid risk of serious injury the distance
between the top safety barrier and the wall shall not exceed 75mm or shall be more than 230mm.
2) The bed complies with EN747-1:2012
1
Safety and Care Advice
!
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Place the product on flat and
steady surface during use.
• Keep these instructions for
future use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing
points be fully tightened.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Safety: To avoid any risk of
suffocation to animals or
children dispose of the plastic
bags immediately.
• Cleaning: As with all surfaces
clean with a damp cloth and
mild detergent, do not use
bleach or abrasive products.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Please check you have all the parts listed below
1
Components - Parts
2
Upper corner post x 4 (4.5 x 108.5cm)
8
Ladder (109 x 35.7cm)
3
End panel (Upper) x 2 (97 x 39.8cm)
4
End panel (Lower) x 2 (25 x 88.5cm)
7
Front guard rail (95.5 x 42cm)
5
Rear guard rail (95.5 x 42cm)
10
Slats x 44 (□2 x 1 x 95cm)
6
Guard rail x 2 (97 x 42cm)
9
End Slats x 4 (□2 x 1 x 95cm)
2
Lower corner post x 4 (4.5 x 66.5cm)
12
External bracket x 2 (4.3 x 2.3 x 12cm)
11
Internal bracket x 4 (3.7 x 1.7 x 12cm)
Smaller diameter
Lower side rail (95.5 x 6.8cm)-Extra hole for ladder
13
Lower side rail × 3 (95.5 x 6.8cm)
14
15
Support foot x 2 (26 x 2.3 x 12cm)
Please check you have all the fittings listed below
Components - Fittings
3
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note:
The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A B C
M6x15mm Allen screw x 8
D E
M6x45mm Allen screw x 8
F
Curved washer-large x 16
G H
J
Nut x 24
K M
Plastic plug x 2
A
Curved washer-small x 31
Plastic washer x 16
M6x65mm Allen screw x 11
M8x65mm Allen screw x 8
M6x10mm Allen screw x 102
L
Plastic cap x 4
M6x35mm Allen screw x 4
R
M6x40mm Allen screw x 8
N
M6x25mm Allen screw x 4
P
Q
Small allen key x 2
Large allen key x 1
S
0
5
10 15 20 25 30 35 40
45
50
55
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2
3
4
5 6
Ruler/tape
measure
Ruler - Use this ruler to help correctly identify the screws
Tools required
Foot x 4
Assembly Instructions
4
Assembling side frames
Lay one corner post
，an
upper end panel and a
lower end panel flat on
the floor as shown.
Note:
The holes in end
panel must be at the
top.
Insert upper end panel
into the large holes in
the corner post.
Secure using fixings
and .
Note:
Do not fully
tighten screws .
Assemble lower end panel
to the corner post
using fixings and .
Note:
Do not fully
tighten screws .
Align another corner post
onto the ends of the upper
and lower end panels.
Secure using fixings ,
and as shown.
Insert end caps into
the top of the corner
posts.
Repeat for the other side
frame.
4
3
3
A
C
A
4
B
C
B
D
C
B
2
4
Top
Bottom
C
B
4
D
3
Step 1
C
A
C
L
1
2
1
2
2
1
3
Step 2
A
B
C
Preparing corner posts
Join upper corner posts
and lower corner
posts together and
secure using fixings
and .
1
2
C
L
Note: Hole at top
A
C
3
1
D
Step 3
L
6
5
Assembly Instructions
5
P
P
J
J
J
J
P
P
L
6
7
J
J
P
P
5
6
11
11
L
6
11
Assembling upper guard
rail (front)
To assemble the front
guard rail, repeat the
assembly from step 3
above, using front guard
rail and remaining
guard rail .
11
6
L
a:
a:
Rear
Front
Step 4
Assembling upper guard
rail (rear)
a: To assemble the rear
guard rail, locate internal
bracket inside guard
rail as shown.
Secure using screw .
b:
b: Locate rear guard rail
over the end of the
internal bracket in guard
rail and secure using
fixings and .
6
5
J
P
7
6
Assembly Instructions
6
L
11
14
14
b:
Step 5
Assembling lower side
rails
a: Locate internal bracket
inside lower side rail
, and secure using
screw .
Slide lower side rail
over the internal bracket
and secure using screw .
Note:
Lower side rail
has an extra hole for the
ladder fixing, This will
become the front
side rail !
L
11
14
13
a:
L
11
13
14
L
14
b: Repeat a: to assemble
two lower side rails
together as shown.
This will become the rear
side rail !
14
11
14
13
L
L
13
Note:
Hole for
ladder fixing.
Rear
Front
Assembly Instructions
Assembling rear guard
and side rail
Two people are needed
here.
With help, stand both
side frames upright.
a: Assemble the rear
guard rail assembly
and in between the
side frames as shown.
Note:
Do not fully tighten
any screws during the
assembly.
Secure at the top using
fixings and as
shown.
Secure at the bottom
using fixings ,
and as shown.
Note:
Plastic washers
are located in between
the rear guard and the
side frames.
5
B C
E F G H
J
F
7
1
B
C
H
E
F
G
6
J
E
F
6
Q
2
Feet to extend outwards.
Step 6
Q
1
2
B
C
H
E
J
E
G
F
H
E
J
E
1
2
Q
2
1
2
1
b:
a:
14
14
6
5
a:
b:
b: Assemble the lower
side rail assembly at
the rear of the side frames
using fixings ,
and as shown.
Note:
Ensure the 24 holes
in side rail are on the
top edge.
With help, fit feet to the
corner posts .
Note:
Ensure the feet
extend outwards as
shown.
Warning:
The bunk bed
is heavy. Lift
with care.
Q
2
14
E F G H
J
14
Holes on top
G
F
G
F
F
E
E
J
H
14
Assembly Instructions
Step 7
E
H
F
G
J
B
C
1
6
E
F
8
J
E
H
F
G
E
F
B
C
H
E
E
F
F
G
J
H
E
J
F
G
2
F
E
14
Alternative assembly
Note: Hole
Note: Hole
b:
a:
Assembling front
guard
At this stage, choose if
you want the ladder on
the right hand side or left
hand side.
a: According to which
side you want the ladder,
assemble the front guard
assembly and in
between the side frames
as shown.
Secure at the top using
fixings and .
Secure at the bottom
using fixngs , , ,
and .
b: Assemble the lower
side rail assembly and
in between the side
frames at the front of the
bed using fixings ,
and .
Note:
Ensure the ladder
fixing holes in the front of
side rail are on the
same side as the ladder
access gap in front guard
.
Note:
Ensure all fixings
are left loose.
E F
G
H
J
13
E F
H
J
13
7
7
6
13
14
Note: Hole
Note: Hole
b:
a:
14
G
6
7
B C
L
A
D
D
E
R
L
A
D
D
E
R
Assembly Instructions
9
Step 8
Assembling end slats
Fit end slats in the
very last fixing holes at
each end of the bed
(top and bottom bunks).
Note:
The arrow labels on
slats must point
outside.
Note:
Slats have been
labelled for easier
identification.
9
9
9
9
Slats at
each end
9
3
Arrow label to
point outside
9
9
9
9
L
L
Assembly Instructions
Step 9
10
12
10
J
12
N
External bracket
Outside
Inside
OR
12
Assembling middle slats
a: Locate external
brackets over the joints
in the front and rear guard
rails on the top bunk.
Note:
Depending on which
way round you have
assembled the front guard
rail, external bracket
will be on either the inside
or outside of the bed.
With help, place two slats
on top of the external
brackets and secure using
fixings and .
J
N
N
J
15
12
10
12
10
N
N
JJ
J
J
N
N
10
12
External bracket
OR
15
N
N
J
J
15
Inside
10
N
N
J
J
10
Outside
15
b: At the lower bunk,
locate support feet
on to the front and rear
side rails.
Note:
Again, depending
on which way round you
have assembled the
front side rail, the
brackets will be located
on either the inside or
outside.
Place two slats on
top of the support feet
and secure using fixings
and .
b:
a:
b:
a:
15
10
J
N
Assembly Instructions
11
Step 10
L
L
10
10
L
L
Assembling slats
Assemble remaining
slats to both bunks
using screws as
shown
.
10
L
L
10
Assembly Instructions
8
Step 11
12
C
J
K
J
8
7
Attaching ladder
Assemble ladder to
front guard and lower
side rail using fixings
and .
Fixings are located
inside the frame as
shown.
Plastic plugs can be
used to cover the un-used
holes in the corner post as
shown.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
7
8
K
C
J
K
C
J
THIS END UP
13
7
M
M
1
13
M
M
M
Assembly is complete.
Important
Once assembly is
complete, ensure all
fixings on the whole
frame are securely
tightened.
Loading...