Argos 171-8140, 145-0446, 157-3622, 170-9214, 160-9785 ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference

Issue 2 - 12/12/13

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Seville - Bedside

171/8140

145/0446

157/3622

170/9214

Width - 35.5cm

Depth - 33cm

Height - 41.5cm

160/9785

162/9325

162/7956

159/7732

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 7kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

2

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

1

2 3

Top/Base (D2493A)

(321 x 327mm) x 2

Left Side (D2494A)

(412 x 328mm)

Right Side (D2495A)

(412 x 328mm)

Drawer Front (D2496A)

(317 x 157mm)

Left Drawer Side (W410LH)

(300 x 95mm)

Right Drawer Side (W410RH)

(300 x 95mm)

Drawer Back (W288-95)

(288 x 95mm)

Drawer Base (T299-297)

(299 x 297mm)

Back (X175-347)

(175 x 347mm)

4 5 6

7

8

9

3

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 2

C

D E F

G

Small locking nut (F3) x 2

Nail (F51) x 540mm Screw (F910) x 8

Handle (F300) x 1

H

Knock-in Peg (F171WH) x 4

I

R (F601)

L (F600)

F599

Drawer stops (F599) x 2 Runners (F600) x 1 and (F601) x 1

25mm Screw (F95) x 1

4

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

B

C

Prepare the drawer front

Screw 2 metal dowels into the holes shown on the back of the drawer front .

Note: Tighten metal dowels up fully against the panels.

B

4

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

C

5

6

Step 2

C

5

C

6

B

4

Step 3

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

5 6

4

C

5 6

B

C

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

4

5

6

Small

groove

Plain chipboard

surface

Assembly Instructions

5

Step 4

H

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

8

5 6

4

7

5 6

8

7

H

5 6

8

5

6

4

665

6

5

SNAP!

F599

I

F599

I

Step 6

Push in drawer stops

Carefully break off the 2 drawer stops (F599) from the drawer runners .

Push the drawer stops fully through the drawer sides and from the inside.

I

5 6

F599

I

F599

I

H

7

8

299mm

Finished

front edge

Assembly Instructions

6

Step 7

Attach the handle

Attach the handle to the drawer front using screw .

4

G

E

Prepare the left side

Separate the runners .

Push fit the left runner marked ‘L’ into the left side .

Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.

I

1

Step 8

Prepare the right side

Push fit the left runner marked ‘R’ into the right side .

Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position.

I

2

Step 9

L

F600

I

R

F601

I

G

E

4

I

1

I

Finished

front edge

2

D

Finished

front edge

Finished

front edge

D

Assembly Instructions

7

Step 10

Step 11

Prepare the top and the base

Tap 2 wooden dowels into the top and the base .

A

3

Join the top to the right side

Push the top onto the right side and secure with 2 screws .

Step 12

3

2

D

A

Plain chipboard

surface

3

Finished

front edge

2

3

x 2

Finished

front edge

3

Join the base to the right side

Push the base onto the right side and secure with 2 screws .

3

2

D

Assembly Instructions

8

Step 13

Fit the left side

Push the left side onto the assembly and secure with 4 screws .

1

D

1

Step 14

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

onto the unit.

Nail around the 3 edges of the back as shown.

Stand the unit up for the next step.

9

F

9

y

x

b:

F

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

9

Assembly Instructions

9

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Insert the drawer

Lift the front of the drawer whilst inserting to overcome the ‘stop’ system.

Note: To ensure that your drawer runs smoothly, spray a small amount of furniture polish into the grooves.

Assembly is complete

Step 15

ALR2908

Assembly Instructions - Please keep for future reference

MADE IN

BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Dimensions

Issue 2 - 04/09/13

Width - 102.5cm

Depth - 49.5cm

Height - 175.5cm

Seville - 3 Door Robe

147/4556

167/8338

173/6146

171/6939

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 59kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

2

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

1 2

Left Side (D2483A)

(1753 x 496mm)

Right Side (D2497A)

(1753 x 496mm)

Upright (D2500A)

(1640.5 x 477mm)

Door (D2487A)

(1652 x 327mm) x 3

Small Back (X1666-332)

(1666 x 332mm)

Large Back (X1666-685)

(1666 x 685mm)

Shelf (D2501A)

(313 x 475mm) x 2

3

Plinth (D2502A)

(995 x 80mm)

Top (D2498A)

(995 x 495mm)

Base (D2499A)

(995 x 480mm)

4

5

6

7

9

10

11

Hanging Rail (FHR659)

(659mm long)

8

3

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

ScissorsSquare

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step ladder

Ruler - Use this ruler to help correctly identify the screws

Electric drill (only use when drilling into walls)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

A

Wooden dowel (F22) x 6

B C

D E F

G H I

Nail (F51) x 36 40mm Screw (F910) x 14

K

M N

Bracket (F327) x 1

13mm Screw (F79) x 1

Hinge plate (F523) x 9

Hinge (F522) x 9

13mm Screw (F63) x 20

Rail holder

(F1014) x 2

Handle (F300) x 3

25mm Screw (F95) x 3

L

Shelf support (F121) x 8

Nail screw (F277) x 5

J

Back holder (F276) x 5

* These can also be round

4

Step 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number

and the reference numbers below)

A

Step 2

10mm

A

Prepare the top and base

Tap 2 wooden dowels into the top .

Tap 2 wooden dowels into the base .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

A

4

5

A

4

A

5

plain chipboard surface

Prepare the upright

Push a rail holder into the upright . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.

H

3

M

3

M

H

F

Finished

front edge

F

3

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

C

Assembly Instructions

5

Step 3

Fit the top and the base to the upright

Fit the top and the base onto the upright . using 4 screws .

C

3

4

5

plain chipboard surface

4

5

3

C

Step 4

Prepare the right side

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

M

2

M

2

Finished

front edge

6

Finished

front edge

1

M

Prepare the left side

Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

H

1

M

1

M

H

F

1

F

Assembly Instructions

Step 5

Step 7

C

2

Fit the right side

Push the right side onto the top and base and secure it using 4 screws .

2

4

5

4

5

C

Step 6

A

Prepare the plinth

Tap 2 wooden dowels into the plinth .

6

A

Plain chipboard

6

C

Assembly Instructions

7

Step 8

Step 9

Fit the plinth

Push the plinth onto the right side and secure it using screw .

6

2

C

Note: Support the plinth until the left side has been fitted in the next step.

6

Finished

front edge

C

1

C

Fit the left side

Push the left side onto the assembly and secure it using 5 screws . .

1

C

8

Assembly Instructions

Step 10

b:

Fit the back

a: Square up the unit by

making sure that measurement x to x

equals y to y.

Place the small back and large back down onto the unit as shown.

Make sure that the 2 backs are pushed up tight against each other and that they meet over the back edge of the upright.

b: Nail around

the outside edges of the 2 backs.

Note: Do not nail where the backs meet. Nails should be spaced about 150mm apart.

10

11

B

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

y

x

B

Warning: The unit is heavy. Lift with care.

10

11

Step 11

Secure the backs

Tap the nail screws through the back holders . and down between the backs and into the back edge of the divider.

Keep tapping the nail screws in until the back holders dig into the small and large back.

Stand the unit up for the next step.

K

J

10 11

K

J

10

11

KJ

+

x 5

Note: Do not nail where the backs meet.

K

J

Note: These can also be round