Argos 1446010 ASSEMBLY INSTRUCTIONS
Samuel Shorty Bunk Bed
Assembly Instructions - Please keep for future reference
162/4131
188/9299
170/8253
IMPORTANT NOTE:
The top surface of the mattress
should not come above this line.
Dimensions
Width - 181cm
Depth - 82cm
Height - 160cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
- Please read these instructions fully before starting assembly
IMPORTANT NOTE:
Do not fully tighten
all bolts until all parts
of the bed are
assembled.
Issue 2 - 20/06/14
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Warnings
• READ CAREFULLY - RETAIN
FOR FUTURE REFERENCE
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
• Always use the ladder for
entering and leaving the upper
bunk.
• The recommended mattress
size is L1750 x W750 mm.
• Ensure thickness of mattress
does not exceed 175 mm.
• Refrain from using the bunk
bed if any structural part is
broken or missing.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Please prohibit more that one
person on the upper bunk.
• Please advise your children to
only enter and leave the upper
bunk by using the ladder.
• Please prohibit children from
jumping on the upper and lower
beds.
• WARNING: Children can
become trapped between the
bed and the wall. To avoid risk
of serious injury the distance
between the top safety barrier
and the wall shall not exceed
75mm or shall be more than
230mm.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Unit weight: 32.5kgs.
• WARNING: Do not allow
children under 6 years of age to
use the upper bunk due to risk
of injury and falls.
• STRANGULATION HAZARD -
Never attach or hang items such
as ropes, strings, cords,
harnesses and belts to any part
of the bunk bed.
• THIS BED COMPLIES WITH
EN747-1:2012 / EN747-2:2012
Manufacturer: BL Packaging Co.
Ltd.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
1
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 640 0800
Please check you have all the parts listed below
End post x 4
1 Upper side safety rail x 2
(Ø4.5 x 160cm)
Lower side rail x 2
3 Lower rail x 2
(75 x 18.5 x 3cm)
5 Upper back safety rail
Upper front safety rail
(173 x 41.5 x 2.5cm)
2
(73.5 x 35.5 x 3.5cm)
4
(173 x 7 x 2.5cm)
6
(173 x 41.5 x 2.5cm)
7 Ladder
Slat x 48
(77.5 x 2.5 x 3cm)
8
(93.5 x 34.5 x 3cm)
2
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A B C
M6 x 65mm Bolt x 15
D E F
Screw x 4
G H I
Strap x 5
M6 x 40mm Bolt & Nut x 12
Curved washer x 31 Spring washer x 31
Plastic Cap x 6
Tools required
Crosshead screwdriver
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
M6 x 20mm Bolt x 8
Allen key x 2
Friendly Tips
• Do not fully tighten all bolts until all parts of
the bed are assembled.
• Assemble lower rails to headboard &
footboard (end panels) first, followed by the
upper safety rails.
• One person must hold on the rails while
another person is assembling it and fitting
bolts to end posts.
3
• When assembling slats, make sure it is
aligned to the holes on the upper and lower
rails before pushing it firmly down.
• After all the parts are positioned, you can
fully tighten all bolts.
Loading...