Argos 12S607X ASSEMBLY INSTRUCTIONS

Assembly Instructions - Please keep for future reference
6524803
Dimensions
Width - 195cm Depth - 122cm Height - 173cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456400800
Issue 1 -27/10/16
!
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on pages 2 & 3.
Remove all fittings from the
plastic bags and separate them into their groups.
Keep children and animals away
from the work area, small parts could choke if swallowed.
Make sure you have enough
space to layout the parts before starting.
Do not stand or put weight on
the parts during assembly, this could cause damage.
Assemble on a soft level
surface to avoid damaging the unit or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
The user of this swing should
always inspect it before each use.
Check the tightness of all nuts
and bolts on a regular basis.
Always remove the canopy in
heavy wind conditions, otherwise the canopy may tip over and cause damage to its parts.
Oil all of the metal parts that
move during usage season.
The manufacturer will not
accept responsibility for unauthorized repairs or modifications to the swing or its parts.
Weight limit is 340 kgs.
Warning: The unit weighs
approximately 28.4 kgs. Please lift with care.
Care and maintenance
Wash frame parts with mild
soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or other solvents on the frame parts.
The canopy may be surface
washed with mild soap and water if necessary. Commercial foaming upholstery cleaner may also be used. Rinse well and hang to dry. Do not machine wash or dry.
We recommend the use of
furniture covers to protect your swing when not in use.
Inspect and tighten all bolts
or fasteners on a regular basis to ensure the proper performance and safety of your swing.
In order to prolong the life and
beauty of your swing, we recommend that it be stored in a dry and protected area when not in use.
1
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
M8 x 110mm Bolt x 4 M6 x 65mm Bolt x 8
M6 x 60mm Bolt x 2
G H I
ST4.2 x 16mm Screw x 4
D12 Spring Washer x 6
M
B C
M6 x 40mm Bolt x 2
D17 Washer x 10
D10 Spring Washer x 18
N
M8 x 60mm Bolt x 2
FED
M6 x 20mm Bolt x 6
D16 Washer x 20
LKJ
M8 x P1.25mm Plastic Nut x 4
O
M6 x P1.0mm Plastic Nut x 8 Leg Cap x 4
P Q R
Plastic End Cap x 6
Canopy/Frame Connector x 2
Tools required
4mm Hex Key
6mm Hex Key 13 & 17mm Nut Wrench
Ruler - Use this ruler to help correctly identify the screws
Suspension Spring x 2
Plastic Screw x 2
Screwdriver (Not provided)
40
2
Components - Parts
Please check you have all the parts listed below
1
Top Cross Beam x 1
4
Lateral Cross Brace x 2
2 3
Front Upright Support x 2
5 6
Rear Cross Brace x 1
Rear Upright Support x 2
Swing Arm x 2
7
Seat Assembly x 1
10 11
Side Canopy Brace x 2
3
8 9
Swing Arm Tube x 4 Front And Rear Canopy x 3
Canopy x 1
Assembly Instructions
Step 1
Note: When fastening with bolts and nuts, always usea washer , , and between the tube and
J K
the bolt and the tube and the nut.
A:
Attach the front and rear upright supports and at the top by using bolts , washers , spring washers , and plastic nuts . Do the same procedure for both sides. Keep the bolts loose.
B:
At both ends, insert the assembled upright support and into the top cross beam . Tighten all of the plastic nuts and bolts now.
C:
Attach the lateral cross braces to the upright supports and by using bolts , washers , spring washers , and plastic nuts . Do the same procedure for both sides.
2
J L
M
3
A
2
B
K
H I
H
3
1
4
2
3
I
FRAME ASSEMBLY
Parts of the assembly will be easier with 2 people.
2
3
J
H
H
A
H
A B
3
JLL
2
C
3
I
I
K
M
4
A
H
3
2
3
B
2
4
1
3
2
B
3
2
4
D:
Attach the rear cross braces to the rear upright supports by using bolts , washers , spring washers , and plastic
M
nuts . Tighten all of the plastic nuts and bolts.
E: Insert the leg caps into all of the base feet.
B
K
N
5 3
I
D
E
3
5
M
K
I
I
B
3
2
N
N
3
5
3
N
N
3
2
4
Assembly Instructions
Step 2
A:
Attach the swing arm to the front of the seat assembly by using bolt , washer , and spring washer . Do the same procedure for both sides. Fix the brace of the swing arm to the seat assembly by using bolt , washer , and spring washer . Do the same procedure for both sides.
B:
Attach swing arm tube to the swing arm and the seat back
7
by using bolt , washer , and spring washer . Do the same procedure for both sides. Attach another swing arm tube
8
to swing arm at the front bend by using bolt , washer
I
, spring washer , and plastic nuts . Do the same procedure for both sides. Do the same procedure for both sides.
C
J
I
6
M
6
7
H
6
7
8
D
K
6
B
K
E
K
I
SEAT ASSEMBLY
Parts of the assembly will be easier with 2 people.
6
7
6
B
8
8
7
6
8
8
6
B
I
7
7
H
8 8
I
6
I
K
E
J
C
I
K
D
6
K
M
Step 3
A: Hook the suspension spring into the top of both swing arm
8
tubes . Do the same procedure for both sides.
5
O
ATTACH SWING SEAT TO FRAME
A
O
8
O
8
8
O
8
O
88
Assembly Instructions
B: Hook the upper loop of the suspension spring through the hole located on the angled brace on the top cross beam . Do the same procedure for both sides.
Warning: Make sure that both ends of the suspension springs go completely through the holes in the angled braces on the top cross beam and the swing arm tubes .
O
1
O
1
8
Step 4
A & B:
Slide the canopy/frame connectors
Q
onto the side canopy braces . . Fix them together by
10
using screws . Make sure that the teeth on the canopy/frame connectors are facing towards the inside of the frame.
G
Parts of the assembly will be easier with 2 people.
B
1
1
O
O
8
O
8
8
1
8
ATTACH THE CANOPY
A
Q
10
B
Q
10
O
10
1
8
Q
O
8
G
G
C:
Insert the front and rear canopy braces into the sleeves of the canopy ( .
D: Attach the side canopy brace to the front and rear canopy braces by using bolts , and spring washers . Do the same procedure for both sides. Tighten all of the bolts now, cover all bolts with plastic end caps .
E: Velcro the canopy to the side canopy braces .
9 11
9
10
F
K
P
11
10
C
D
E
10
11
11
9
9
9
11
9
9
9
10
9
K
10
F
P
10
11
6
Assembly Instructions
Step 5
Fix the canopy/frame connectors to the adjustable teeth on the
Q
top cross beam by using a plastic screw . Do this procedure for both sides.
1
R
Parts of the assembly will be easier with 2 people.
11
1
R
Q
1
1
R
Q
Step 6
To assure stability, double check that all of the bolts have been completely tightened.
Note: To avoid danger of suffocation, always keep plastic bags or small parts away from babies and children.
Assembly is completed.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456400800 Retailer: Argos Address: 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes Bucks, MK9, 2NW
7
Loading...