Arecont Vision AV10355PMIR-SH, AV10355PMTIR-SH, AV1355PM-S, AV1355PMIR-S, AV2355PM-H Installation Manual

!

MegaDome® G3

Installation Manual

Models

1.2 Megapixel

AV1355PM-S

AV1355PMIR-S

1080p

AV2355PMIR-SH

AV2356PMIR-S

AV2355PMIR-SAH

AV2355PMTIR-SH

AV2356PMTIR-S

3 Megapixel

AV3355PMIR-SH

AV3356PMIR-S

AV3356PMIR-SA

AV3355PMTIR-SH

AV3356PMTIR-S

5 Megapixel

AV5355PMIR-SH

AV5355PMIR-SAH

AV5355PMTIR-SH

10 Megapixel

AV10355PMIR-SH

AV10355PMTIR-SH

Installation Manual

Page | 2 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Contents

!

Package Contents .................................................................................................................................... 3

Camera Overview ..................................................................................................................................... 6

Installation ................................................................................................................................................. 7

Surface Mount ..................................................................................................................................... 10

Wall Mount .......................................................................................................................................... 13

Pendant Mount ................................................................................................................................... 16

Pole Mount .......................................................................................................................................... 19

Corner Mount ...................................................................................................................................... 21

Electrical Box Adapter ........................................................................................................................ 23

Adjusting the Pan, Tilt and Focus ........................................................................................................... 24

Auxiliary I/O Functions ............................................................................................................................ 26

Camera Power Up .................................................................................................................................. 28

SD Card Set-up ...................................................................................................................................... 30

SD Card Tab ........................................................................................................................................... 33

SD Card Setup via AV200 ...................................................................................................................... 34

Camera Discovery, Setup, and Configuration ........................................................................................ 35

Network Protocols ................................................................................................................................... 35

General Remote Focus ........................................................................................................................... 36

Refined Remote Focus ........................................................................................................................... 37

AV IP Utility Focus Tab ........................................................................................................................... 39

Mounting Templates ............................................................................................................................... 40

Support ................................................................................................................................................... 41

Installation Manual

Page | 3 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

CAUTION!

1. Do not attempt to service a damaged unit yourself. Refer all servicing to qualified service
personnel.

2. Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and

with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or

Recognized wire suitable for the application.

3. Always use hardware e.g. screws, anchors, bolts, locking nuts etc. which are compatible with

mounting surface and of sufficient length and construction to insure a secure mount.

Package Contents

This equipment should be unpacked and handled with care. The original packaging is the safest

container in which to transport the unit and can be used if returning the unit for service. The packaging

contains:

10

8

9

11

12

13

Installation Manual

Page | 4 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

Reference #

Description

1

1x Arecont Vision MegaDome® G3 camera

2

1x Dome Cover

3

1x Mounting Plate

4

1x Grommet with Through Hole

5

1x Grommet without Through Hole

6

1x Insertion Tool

7

4x #6-32 1.0” Wood/ Metal Sheet Screw
8

4x #6-32 1.0” Drywall/ Masonry Mounting Anchors

9

4x #8-32 0.5” Machine Screw

10

1x Security L-key

11

1x Set Screw L-key

12

1x Mounting Template

13

1x Magnetic core

1x I/O cable

1x AC & DC auxiliary power cable

1x CD with Manual and Software

!

!

!

!

!

!

!

!

Installation Manual

Page | 5 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Warranty Information

Global (3 Year) Limited Warranty

ARECONT VISION warrants to Purchaser (and only Purchaser) (the “Limited Warranty”), that: (a) each
Product shall be free from material defects in material and workmanship for a period of thirty-six (36)
months from the date of shipment (the “Warranty Period”); (b) during the Warranty Period, the
Products will materially conform with the specification in the applicable documentation; (c) all licensed
programs accompanying the Product (the “Licensed Programs”) will materially conform with applicable
specifications. Notwithstanding the preceding provisions, ARECONT VISION shall have no obligation or
responsibility with respect to any Product that (i) has been modified or altered without ARECONT
VISION’s written authorization; (ii) has not been used in accordance with applicable documentation; (iii)
has been subjected to unusual stress, neglect, misuse, abuse, improper storage, testing or connection;
or unauthorized repair; or (iv) is no longer covered under the Warranty Period. ARECONT VISION
MAKE NO WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
OTHER THAN THE EXPRESS LIMITED WARRANTIES MADE BY ARECONT VISION ABOVE, AND
ARECONT VISION HEREBY SPECIFICALLY DISCLAIMS ALL OTHER EXPRESS, STATUTORY AND
IMPLIED WARRANTIES AND CONDITIONS, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT AND THE
IMPLIED CONDITION OF SATISFACTORY QUALITY. ALL LICENSED PROGRAMS ARE LICENSED
ON AN “AS IS” BASIS WITHOUT WARRANTY. ARECONT VISION DOES NOT WARRANT THAT (I)
THE OPERATION OF THE PRODUCTS OR PARTS WILL BE UNINTERRUPTED OR ERROR FREE;
(II) THE PRODUCTS OR PARTS AND DOCUMENTATION WILL MEET THE END USERS’
REQUIREMENTS; (III) THE PRODUCTS OR PARTS WILL OPERATE IN COMBINATIONS AND
CONFIGURATIONS SELECTED BY THE END USER; OTHER THAN COMBINATIONS AND
CONFIGURATIONS WITH PARTS OR OTHER PRODUCTS AUTHORIZED BY ARECONT VISION
OR (IV) THAT ALL LICENSED PROGRAM ERRORS WILL BE CORRECTED.

For RMA and Advance Replacement information visit http://www.arecontvision.com

!

Installation Manual

Page | 6 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Camera Overview

MegaDome® G3 third generation multi-megapixel cameras provide ample resolution to zoom-in for

details in live or recorded video. These indoor/outdoor all-in-one solutions integrate a 1.3, 1080p, 3, 5

or 10-megapixel (MP) sensor with fast frame rates, and SNAPstream™ (Smart Noise Adaptation and

Processing) technology to reduce bandwidth without impacting image quality. Together with an IR

corrected motorized, P-iris wide angle or telephoto varifocal lens, remote focus and remote zoom make

MegaDome G3 easy to install and manage. The installer-friendly housing is IP66 environmental rated

and IK-10 impact-resistant. MegaDome G3 is feature-loaded, and select models include STELLAR™

(Spatio Temporal Low Light Architecture) for best-in-class light sensitivity capturing details in near

complete darkness, or wide dynamic range (WDR) for applications with bright or over saturated lighting

conditions.

Installation Manual

Page | 7 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Installation

!

1. Determine a secure location to mount the camera.

2. Use the supplied security L-key, to loosen the four (4) screws securing the dome cover.

3. Remove the dome cover and protective foam. Do not remove screws from the dome cover.

The MegaDome® G3 camera has been designed to provide installers with flexible mounting
options such as ceilings, walls, poles or corners.

NOTE: When mounting the camera outdoors or in a wet environment, use of supplied grommet
is recommended. Ensure the grommet properly seated flush with the camera housing.

Installation Manual

Page | 8 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Ensure you have the proper compatible mounting parts prior to starting your installation:

!

Pendant mount

Reference #

Pendant Mount Components Required

1

Pendant mount (AV-PMJB) with integrated junction box

2

MegaDome® G3 camera

3

MD-CAP mounting cap

!

!!!!!!!!

!

Wall mount

Reference #

Wall Mount Components Required

1

Wall mount (AV-WMJB) with integrated junction box

2

MegaDome® G3 camera

3

MD-CAP mounting cap

Installation Manual

Page | 9 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

Pole mount

Reference #

Pole Mount Components Required

1

Wall mount (AV-WMJB) with integrated junction box

2

MD-CAP mounting cap

3

MegaDome® G3 camera

4

AV-PMA pole mount adapter

!

!

Corner mount

Reference #

Corner Mount Components Required

1

Wall mount (AV-WMJB) with integrated junction box

2

MD-CAP mounting cap

3

MegaDome® G3 camera

4

AV-CRMA corner mount adapter

4. Use the Arecont Vision software AV IP Utility located on the CD or available for download at our
website (www.arecontvision.com) for camera discovery and setup (see Instruction Manual located on
the CD or available on our website).

Installation Manual

Page | 10 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Surface Mount

The MegaDome® G3 camera can be directly attached onto hard ceilings or walls including wood,
plastic, metal and concrete.

1. Use the template, anchors, and screws provided to prepare the mounting provisions for the
camera installation.

2. Use the supplied security L-key, to loosen the four (4) tamper resistant screws securing the
dome cover as shown in Figure 1. Do not remove screws from the dome cover.

Figure 1

3. Remove the protective foam and discard.

4. Install four supplied dry wall anchors using the supplied mounting template.

5. Align four supplied screws with the dry wall anchors and screw mounting plate into place as
shown in Figure 2.

!

Figure 2

Installation Manual

Page | 11 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

6. Prepare the network cable with the supplied grommet and insertion tool as shown in Figure 3.

Figure 3

NOTE: When mounting the camera outdoors or in a wet environment, use of supplied grommet
is recommended. Ensure the grommet is properly seated flush with the camera housing.

7. Align the hole on MegaDome® G3 camera with the hole on mounting plate, and install the
grommet on camera housing as shown in Figure 4.

!!

Figure 4

NOTE: If using the side connection of the NPT port, you need to install the supplied grommet
without a through hole on the camera housing, and remove the cap covering the side entrance,
otherwise; leave the cap in place. If using the NPT port, always use Teflon tape around the
threads to ensure proper sealing. The conduit fits ¾” NPT standard. Ensure NPT port is facing
downward.

Installation Manual

Page | 12 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

8. Fasten securely four captive screws as shown in Figure 5.

!

Figure 5

9. Attach the Dome Cover to the MegaDome® G3 camera and fasten securely four captive
screws.

NOTE: When attaching the Dome Cover, make sure the IR foam on the lens not block the field
of view.

10. To configure the camera, reference the camera discovery, set-up and configuration section.

!

CAUTION! The captive screws must be used to properly secure the dome cover and

camera housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly seated
and not folded. Failure to do so may result in water and dust ingress. Water damage from
improper installation is not covered by the warranty!

!

!

!

!

!

!

!

!

!

!

Installation Manual

Page | 13 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Wall Mount

For a proper wall mount installation, the AV-WMJB wall mount and MD-CAP wall mount cap are
required (sold separately). A wall mount should only be attached onto hard ceilings including
wood, plastic, metal, and concrete.

1. Using the Mounting template, prepare the mounting provisions for the camera installation.

2. Connect wall mount cap and wall mount as shown in Figure 1.

Figure 1: Attach wall mount cap to the wall mount

NOTE: The thread size for Top shield, pendant pole and mount is 1.5” NPT.

3. Attach the wall mount to the wall using the four drywall screws provided or any optional
hardware suitable for the mounting surface.

4. Run the Ethernet Cable and outside power cable (if necessary) through the supplied rubber
gasket and then through the wall mount. Ensure the gasket is seated properly.

5. Attach the mounting plate to the MD-CAP with the supplied screws as shown in Figure 2.

Figure 2

Installation Manual

Page | 14 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

6. Prepare the network cable with the supplied grommet and insertion tool as shown in Figure 3.

Figure 3

NOTE: When mounting the camera outdoors or in a wet environment, use of supplied grommet
is recommended. Ensure the grommet is properly seated flush with the camera housing.

7. Align the hole on MegaDome® G3 camera with the hole on mounting plate, and install the
grommet on camera housing as shown in Figure 4.

!!!!!!!!!

Figure 4

8. Fasten securely four captive screws as shown in Figure 5.

!!!

Figure 5

Installation Manual

Page | 15 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

9. Attach the Dome Cover to the MegaDome® G3 camera and fasten securely four captive screws
as shown in Figure 6.

!

Figure 6

NOTE: When attaching the Dome Cover, make sure the IR foam on the lens not block the field
of view.

10. To configure the camera, reference the camera discovery, set-up and configuration section.

!

CAUTION! The captive screws must be used to properly secure the dome cover and

camera housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly seated
and not folded. Failure to do so may result in water and dust ingress. Water damage from
improper installation is not covered by the warranty!

Installation Manual

Page | 16 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Pendant Mount

For a proper pendant mount installation, the AV-PMJB pendant mount and MD-CAP mounting cap
are required (sold separately). A pendant mount should only be attached onto hard ceilings including
wood, plastic, metal, and concrete.

1. Using the mounting template, prepare the mounting provisions for the camera installation.

2. Connect top shield, pendant pole and mount together as shown in Figure 1.

!

Figure 1: Attach the mount cap and pendant mount

NOTE: The thread size of top shield, pendant pole and mount is 1.5” NPT.

3. Attach the pendant mount to the ceiling using the four wood screws provided or any optional
hardware suitable for the mounting surface.

4. Run the Ethernet Cable and outside power cable (if necessary) through the supplied rubber
gasket and then through the pendant. Ensure the gasket is seated properly.

5. Attach the mounting plate to the MD-CAP with the supplied screws as shown in Figure 2.

!!!!!!!!!
Figure 2

Installation Manual

Page | 17 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

6. Prepare the network cable with the supplied grommet and insertion tool as shown in Figure 3.

Figure 3

NOTE: When mounting the camera outdoors or in a wet environment, use of supplied grommet
is recommended. Ensure the grommet is properly seated flush with the camera housing.

7. Align the hole on MegaDome® G3 camera with the hole on mounting plate, and install the
grommet on camera housing as shown in Figure 4.

!!!!!!!!!

Figure 4

8. Fasten securely four captive screws as shown in Figure 5.

! !!!!!!!!!

Figure 5

Installation Manual

Page | 18 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

9. Attach the Dome Cover to the MegaDome® G3 camera and fasten securely four captive
screws as shown in Figure 6.

!

Figure 6

NOTE: When attaching the Dome Cover, make sure the IR foam on the lens not block the field
of view.

10. To configure the camera, reference the camera discovery, set-up and configuration section.

!

CAUTION! The captive screws must be used to properly secure the dome cover and

camera housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly seated
and not folded. Failure to do so may result in water and dust ingress. Water damage from
improper installation is not covered by the warranty!

Installation Manual

Page | 19 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

Pole Mount

For a pole mount installation, the AV-WMJB wall mount, AV-PMA pole mount, and MD-CAP mount
cap are required (sold separately). A pole mount should only be attached onto hard ceilings
including wood, plastic, metal, and concrete.

1. Using the mounting template, prepare the mounting provisions for the camera installation.

2. Connect the wall mount cap and wall mount.

3. Attach the Junction Box Adapter to the Pole Mount Adapter as shown in Figure 1.

4. Remove the conduit plug on the junction box adapter and connect ¾” NPT conduit to the
junction box adapter (Figure 1).

Figure 1: Attach conduit to AV-JBA junction box adapter

Reference #

Description

1

Remove conduit plug

2

Connect ¾” NPT conduit to junction box adapter
(ensure use of water seal tape)

NOTE: Use silicon or water pipe seal tape to make sure no water leakage between conduit
pipe and junction box adapter.

5. Run the Ethernet cable and outside power cable (if necessary) through the supplied rubber
gasket and then through the Junction Box Adapter and AV-WMJB, Wall Mount Adapter. Ensure
the gasket is seated properly.

6. Attach the Wall Mount Adapter (AV-WMJB) to the Pole Mount Adapter (AV-PMA) as shown in
Figure 2.

Installation Manual

Page | 20 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

!!

Figure 2: Attach wall mount adapter to pole mount adapter

Reference #

Description

1

Steel straps with compression screws

2

AV-WMJB wall mount

3

MD-CAP mount cap

4

Conduit

5

AV-PMA pole mount

6

Apply Teflon water seal tape to the thread of ¾” NPT
pipe to avoid water leakage

!

7. Use the supplied two Steel Straps to attach the Pole Mount Adapter to the pole and tighten the
compression screws as shown in Figure 2.

8. To attach the camera to the Wall Mount Adapter (AV-WMJB), reference the Installation and Wall
Mount section.

9. To configure the camera, reference the camera discovery, set-up and configuration section.

!

CAUTION! The captive screws must be used to properly secure the dome cover and

camera housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly seated
and not folded. Failure to do so may result in water and dust ingress. Water damage from
improper installation is not covered by the warranty!

Installation Manual

Page | 21 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Corner Mount

For a corner mount installation, the AV-WMJB wall mount, AV-CRMA corner mount, and MD­CAP mount cap are required (sold separately). A corner mount should only be attached onto
hard corner surfaces including wood, plastic, metal, and concrete.

1. Using the Mounting template, prepare the mounting provisions for the camera installation.

2. Connect the wall mount cap and wall mount.

3. Attach the Junction Box Adapter to the Corner Mount Adapter as shown in Figure 1.

4. Remove the conduit plug on the junction box adapter and connect ¾” NPT conduit to the
junction box adapter as shown in Figure 1.

!

Figure 1: Attach conduit to SV-JBA junction box adapter

Reference #

Description

1

Remove conduit plug

2

Connect ¾” NPT conduit to junction box adapter

(ensure use of water seal tape)

!

NOTE: Use silicon or water pipe seal tape to make sure no water leakage between conduit pipe
and junction box adapter.

5. Run the Ethernet cable and outside power cable (if necessary) through the supplied rubber
gasket and then through the Junction Box Adapter and AV-WMJB, Wall Mount Adapter. Ensure
the gasket is seated properly.

6. Attach the Wall Mount Adapter (AV-WMJB) to the Corner Mount Adapter (AV-CRMA) as shown
in Figure 2.

Installation Manual

Page | 22 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

Figure 2: Attach corner mount adapter to exterior corner wall

Reference #

Description

1

Attach corner mount adapter to exterior 90 corner wall

2

AV-WMJB wall mount

3

MD-CAP mount cap

4

Conduit

5

AV-CRMA corner mount adapter

6

Apply Teflon water seal tape to the thread of ¾” NPT
pipe to avoid water leakage

!

7. Using the screws provided (or other hardware), attach the Corner Mount Adapter to an exterior
90 degree corner wall.

8. To attach the camera to the Wall Mount Adapter (AV-WMJB), reference the Installation and Wall
Mount section.

9. To configure the camera, reference the camera discovery, set-up and configuration section.

!

CAUTION! The captive screws must be used to properly secure the dome cover and

camera housing. Failure to use the captive fastener may result in serious injury. When
mounting the dome cover to the camera housing, ensure that the gasket is properly seated
and not folded. Failure to do so may result in water and dust ingress. Water damage from
improper installation is not covered by the warranty!

Installation Manual

Page | 23 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Electrical Box Adapter

The mounting plate is used to attach the camera to a common single, double or square electrical
box.

1. Using the supplied machine screws, match the mounting holes on the mounting plate with the
threaded holes on the electrical box. Ensure every threaded hole is matched with a mounting
hole.

2. Attach the mounting plate to the user supplied electrical box as shown in Figure 1.

!

Figure 1: Attach the mounting plate to common electrical box

Installation Manual

Page | 24 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Adjusting the Pan, Tilt and Focus

1. Remove the dome cover by loosening the captive fasteners with the supplied security L-key
screwdriver.

2. Power on the camera to adjust the pan, tilt and focus.

3. Remove the shroud from the camera gimbal, and then loose two Philips head screws and loose
one set-screw with the supplied set screw L-key, and then adjust the pan and tilt to obtain the
desired field of view as shown in Figure 1. NOTE: Do not remove the screws!

!

Figure 1: Loose camera head to adjust the field of view

4. Lock the camera head in place by fastening securely two Philips head screws and one set­screw back. NOTE: Do not over torque the screws.

5. Install the shroud back on the camera gimbal as shown in Figure 2.

!

Figure 2

Installation Manual

Page | 25 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

NOTE: Make sure align locking features of the shroud with mating parts on the camera gimbal as

shown in Figure 3.

!

Figure 3

6. To adjust the zoom and focus, see the Remote Zoom/ Focus Section of this manual.

Installation Manual

Page | 26 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Auxiliary I/O Functions

The auxiliary input and output are accessible after removing dome cover.

Reference #

Description

1

Input (White + / Black -)

2

Output (Orange + / Yellow -)

NOTE: MegaDome® G3 camera supports digital input and digital output. See Table 1 for electrical
characteristics.

Electrical Characteristics

MIN

MAX

Input Voltage (V)
(Measured between +
and – terminals)

ON

3.5

6.3

OFF

0

1.3

Output Current (mA)
(Measured between +
and – terminals)
Applied Voltage
Range: 0-80V

ON - 50

OFF

-

0.1

Table 1

NOTE: The digital input is electrically isolated from the rest of the camera’s electrical circuitry via
general-purpose photo couplers. The input is additionally protected with a serial 250 Ohm resistor, and
a de-bouncing circuit. Duration of any input signal should be at least 5 ms to comply with the
requirements of the de-bouncing circuit.

NOTE: Table 2 shows the cable color for digital input and output.

Installation Manual

Page | 27 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Digital I/O

Orange

Digital OUT +

Yellow

Digital OUT -

White

Digital IN +

Black

Digital IN -

Table 2

Installation Manual

Page | 28 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Camera Power Up

This product should be installed by a qualified service technician in accordance with the
National Electrical Code (NEC 800 CEC Section 60) or applicable local code.

1. Connect the camera to a PoE port on 100Mbps network PoE switch using an Ethernet cable as
shown in the image below.

!

Reference #

Description

1

PoE Connector

2. If the camera is powered by an outside power supply, 12-48 VDC or 24VAC, connect the power
cable.

3. Connect the PoE switch to your computer’s network port using an Ethernet cable.

Auxiliary Power

If the camera is powered by a separate outside DC or AC power source, run the supplied power
cable through the access hole on the camera housing and connect the power cable to the 2­position connector on the main camera board. The approximate location of the 2-position
connector is circled below.!!

Installation Manual

Page | 29 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

!

!

!

!

!

!

!

!

!

NOTE: Cameras using auxiliary power with 802.1x enabled may need to manually power cycle the
camera to reconnect to the network.

CAUTION! Make the connections inside a watertight compartment. Isolate unused power
wires individually.

After connections are made, ensure that the watertight compartment is tightly closed and
cables and conduits are properly sealed to prevent ingress of water.

NOTE:&A&yellow&LED&on&the&rear&of&the&camera&illuminates&after&a&few&seconds.&&

• The flashing yellow LED indicates that a link to your computer has been established.

• A green LED will blink when the camera has been accessed.

LED

Status

Description

Yellow
Flashing

Link has been established.

Solid

Normal Operation.

Green
Flashing

Camera has been accessed. Normal operation.

Solid

N/A

None

None

No Connection.

NOTE: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized
wire suitable for the application.

Installation Manual

Page | 30 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

Locally Storing Data

The MegaDome® 4K camera includes a SDHC card slot for onboard storage. To set-up the SD card
features, the Web Interface page or AV 200 can be used.

The camera supports class 10 microSD or microSDHC cards up to 32GB. Not all SD cards are the
same. Arecont Vision highly recommends using SanDisk Extreme Micro SD cards (or an equivalent
substitute) as these cards have been fully tested without issue. The SanDisk Extreme line is better
suited for demanding applications like constant recording. Typical lower grade SD cards are meant for
multimedia applications and will, at times, have questionable quality and reliability.

Recording to the SD card is FIFO (first in first out). The oldest (first) entry is deleted first as new storage
requirements arise. There is no indication when this will happen. Storage time is dependent on a variety
of factors such as SD card size and camera FPS.

SD Recording supports video only. Audio is not supported.

SD Card Set-up

Insert an SD card (user supplied) into the SD card slot until it locks in place. The location of the SD card
slot is located on the main unit. The SD card can only be set-up via the Web Interface or AV200
Software.

Note: Upon insertion or removal of an SD card, the camera must be rebooted.

Note: It is recommended to setup recording time to extend at least 60 seconds past the desired
stopping point to avoid missing critical recorded video.

Installation Manual

Page | 31 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

SD Card Set-up via Web Interface

To set-up the SD card via the web interface, open your preferred web browser and type the camera’s
IP address.

NOTE: For supporting H.264 streaming on a webpage, the recommended browsers are Internet
Explorer and Firefox.

Figure 1

Click SD Card tab

!!!!!!!

Figure 2

Select one of the recording methods:

•

Continuous Recording to start continuously recording.

•

Stop Continuous Recording AND Enable Event-triggered Recording to enable

events recording for network failure, motion alarm and/or I/O alarm trigger.

Installation Manual

Page | 32 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

The Start and End times are visible once the camera starts recording as shown in Figure 3. The start
time represents the beginning time of the oldest recording.

Figure 3

To playback recorded video:

• Input the date and time of the desired video (must be set between the Start and End time).

• Check the Playback SD card video checkbox to play the video.

Playback tips:

Video recorded to an SD card from an Arecont Vision camera can only be played back via an
Arecont Vision camera that has the same or lower resolution. Playback cannot be viewed with any
other device. For example, video recorded to an SD card via a 10MP camera can be played back
on a 3MP camera but a 3MP cannot be played back on a 10MP model.

• SD card must be inserted to any AV camera.

Installation Manual

Page | 33 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

SD Card Tab

Menu

Feature

Description

View SD Recording
ROI

Allows the user to drag the box to the area where need

to be recorded.

Continuous Recording

Allows the user to continuously record without restriction.
Default is unchecked box.

Stop Continuous
Recording AND Enable
Event-triggered
Recording

Allows the user to enable events recording when network
failure, motion alarm, or an I/O alarm is triggered. Default
is unchecked box.

NOTE: if the continuous recording is disabled and no
event recording is enabled, the SD card will not initiate
recording.

Network Failure

Allows the SD Card to record video only in the event that
the network fails.

Motion Alarm

Allows the SD Card to record video only in the event that
motion is detected.

I/O Alarm

Allows the SD Card to record video only in the event that
an I/O alarm is triggered.

Recording Framerate

Allows setting a frame rate output limit for the H.264 video
stream. Reducing the frame rate output is another way to
control the bandwidth used for the H.264 video streaming
from the camera trade off is the obvious reduction of
frame rate output at the camera.

SD Record Video Type

Provides the ability to set the record video type. Options
are JPEG and H.264.

SD Card Image
Resolution

Provides the ability to set the resolution. Options are Full,
Half, or Scaled. Half is the default.

Playback

Allows the user to choose the specific time of video to
playback.

Start

Shows the beginning time frame of the video being
recorded. No default.

End

Shows the ending time frame of the video being recorded.
No default.

Delete All Records

Allows the user to delete any previously recorded video on
the SD card.

Installation Manual

Page | 34 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

SD Card Setup via AV200

To set-up the SD card via AV200, launch the AV200 application icon on the desktop.

!

To enable recording to the SD card, select the desired camera and drag it to the workspace to open a
view. From the window, select the SD card drop down menu. Choose:

• Continuous Recording

- OR -

• Event-triggered Recording to enable events recording for network failure, motion alarm or I/O
alarm

To launch the SD card playback window, click on the SD card icon.

• Set play range to full span sets the playback range to the maximum available on the SD card.

• Set playback range allows the user to input the playback date and time manually.

• Export play exports an .avi file for playback on most media players.

Installation Manual

Page | 35 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

System Requirements

Computer with Windows XP/Vista/7 operating system, network access, and Microsoft Internet Explorer
web browser version 9.0 or later (32-bit).

Camera Discovery, Setup, and Configuration

For camera discovery and setup, the AV IP Utility is recommended. The software can be found on the
CD included with your camera or at: http://www.arecontvision.com/softwares.php.

The AV IP Utility has the ability to provide multiple discovery options, including broadcast and multicast,
check the status of a camera, change camera settings, import and export camera settings via a .csv
file, and update firmware and/or hardware from virtually anywhere with a network connection.

Whether used for large installations that require an update to multiple settings, or smaller installations
where only one camera needs changed, the AV IP Utility tool is efficient and convenient for mass or
single camera uploads.

The AV IP Utility tool is compatible with all Arecont Vision® megapixel cameras. The user manual for
the software is included on the CD that came with your camera or available on our website.

Network Protocols

The Arecont Vision MegaDome® 4K cameras support RTSP, RTP/TCP, RTP/UDP, HTTP, HTTPs,
DHCP, TFTP, QoS, IP version 4 (IPv4), IP version 6 (IPv6), and 802.1x.

RTSP – Cameras communicate with video management systems over Real Time Streaming Protocol.
Do not change the RTSP port unless you are sure your VMS does not use the default setting.

RTP/TCP – The Real-time Protocol/Transmission Control Protocol is best suited for applications that
require high reliability, and transmission time is relatively less critical.

RTP/UDP – The Real-time Protocol/User Datagram Protocol is used for live unicast video, especially
when it is important to always have an up-to-date video stream, even if some images are dropped.

HTTP – The Hypertext Transfer Protocol is an application protocol for distributed, collaborative,
hypermedia information systems.

HTTPs – Hypertext Transfer Protocol Secure: encrypts and authenticates communication between
Web server and browser. (Except 1.3MP and Audio models )

DHCP – The Dynamic Host Configuration Protocol allows network administrators to centrally manage
and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP
address notification, or if the DHCP can update a DNS server.

TFTP – The Trivial File Transfer Protocol is a simple, lock-step, File Transfer Protocol which allows a
client to get from or put a file onto a remote host. TFTP lacks security and most of the advanced
features offered by more robust file transfer protocols such as File Transfer Protocol.

Installation Manual

Page | 36 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

QoS – Quality of Service guarantees a certain level of a specified resource to selected traffic on a

network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by
controlling the amount of bandwidth an application may use.

IPv4 – The MicroDome G2 supports the IPv4 internet-layer protocol for packet-switched
internetworking across multiple IP networks. IPv4 uses 32-bit addressing which allows for devices and
users on the internet for routing traffic.

IPv6 – This camera supports the IPv6 internet-layer protocol for packet-switched internetworking
across multiple IP networks. IPv6 uses 128-bit addresses, which allows for many more devices and
users on the internet as well as extra flexibility in allocating addresses and efficiency for routing traffic.

802.1x – The IEEE 802.1x standard provides a general method for authentication and authorization in
IEEE-802 networks. Authentication is carried out via the authenticator, which checks the transmitted
authentication information using an authentication server and approves or denies access to the offered
services (LAN, VLAN or WLAN) accordingly.

General Remote Focus

1.

To control the remote focus via the web interface, double click the camera within the AV IP
Utility (Figure 1) or open your preferred web browser and type the camera’s IP address (Fig 2).

NOTE: For supporting H.264 streaming on a webpage, the recommended browsers are Internet
Explorer and Firefox.

!

Figure 1: Double click via AV IP Utility

Figure 2: Type the camera IP address

2.

Click Focus Tab

NOTE: Additional information regarding the Arecont Vision® web interface is found separately in the!AV

IP Utility Web Browser Manual!via the Arecont Vision website.

3. Click the Full-range Focus button. The camera begins to autofocus with the lens stopping at the
best overall point of focus. When the focus area turns to Green, the autofocus is complete.

Installation Manual

Page | 37 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

!

!

Refined Remote Focus

1. For a more refined, detailed focus!For a more refined, detailed focus, scroll to the Video Tab
section and select the Enable Digital Zoom Control radial button.

!

2. Choose an area that has a lot of objects or an area you have an interest in seeing more details.
Left click and drag the box to the area where you want to see finer details. The image zooms in.

3. Repeat until you are able to see pixelization of the image.

Installation Manual

Page | 38 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

4. Scroll to the Focus Tab section and enable the View Focus Window.

5. Left click and drag to highlight the area within the zoomed window you created.

6. Click Short-range Focus button.

7. The camera proceeds to go through the short range adjustment around the original focus. It
stops at the best point of focus using the new reference area. When the box around the image
illuminates green, the camera has completed the focus. For an additional focus, press the
manual focus buttons (+20, +5, +1, -20, -5, -1).

8. When satisfied with the camera’s focus setting, scroll to the Video Tab section and select the
Enable Digital Zoom Control radial button.

9. Double click the image; the video returns to the full field of view.

Installation Manual

Page | 39 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

AV IP Utility Focus Tab

!

Menu

Feature

Description

View Focus Window

Allows the user to drag the box to the area where need to
be focused on.

Manual Zoom/ Focus:
+20, +5, +1, -20, -5, -1

Numbers indicate the level of Zooming/ focusing in order to
adjust the field-of-view.

Full-range Focus

Best for scenes that are completely out of focus. The
camera automatically scans the full focus range of the
scene to find the best focus position.

Short-range Focus

Best for scenes that are slightly of out of focus. The camera
quickly fine-tunes for a precise focus position.

Stop

Stops any command in progress.

Installation Manual

Page | 40 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Mounting Templates

!

Unit:&Inches&

!

Installation Manual

Page | 41 [e-mail]

!
!

+1.818.937.0700 877.CAMERA.8 www.arecontvision.com [e-mail]

MegaDome® G3

Support

1. Arecont Vision FAQ Page Located at ArecontVision.com

2. Check the following before you call:

• Restore camera to factory default with AV200 or the camera webpage.

• Upgrade to the latest firmware by visiting ArecontVision.com.

• Isolate the camera on a dedicated network and test with AV200.

• Swap the “troubled” camera with a known good camera to see if the problem follows the

camera or stays at the location.

3. Contact Arecont Vision Technical Support one of three ways:

1. Online Portal: Support.ArecontVision.com

2. Phone: [phone] (option #1)

3. Email: [e-mail]

4. Use the Arecont Vision software AV IP Utility located on the CD or available for download at our
website (www.arecontvision.com) for camera discovery and setup (see Instruction Manual
located on the CD or available on our website).

!

!

!

!

!

!

!

!

!

!