Arcam FMJ A29 User Manual
A29
Audiophile Amplication
• Integrated stereo amplifier
• 80W Class G amplification
• On board PSU for rSeries products
• CR902 system remote control
• Phono input configurable for line/MM
• Large ergonomically designed aluminium knob
• Low power 0.5W standby
Arcam’s A29 integrated amplier represents another major
step forward for Arcam’s stereo audio engineering. We set out
to incorporate everything we have learnt in almost 40 years
to deliver an amplier that will set new standards and provide
class leading sound quality for the best possible reproduction
of your music.
Drawing on the many years of amplier design experience
at Arcam, the A29 uses the best quality components and
engineering practice to produce a product that will give many
years of musical pleasure and reliable service.
“Arcam once again
proves that class G
amplification is the
ultimate topology.”
Alex Sandulescu, Product Manger, Arcam
With a class G amplier, toroidal based power supply,
acoustically damped chassis, complementary transistor
output stages and exceptionally low levels of distortion and
noise the A29 is capable of reproducing music with all its
original authority and detail. Rest assured you will be hearing
the music just as the artist intended.
The A29 have been designed to leapfrog the competition with
a massive 80 watts per channel into 8 ohms and 175 watts into
4 ohms, allowing for huge extra power reserves from our latest
generation class G topology that is both clever and efcient.
During normal operation, distortion is measured in less than
one part per million so that this massive power is deliver with
total control and nesse.
There have been great strides made in improving audio
sources and loudspeakers in recent years and the time is right
to match them in the eld of amplier design. This ground
breaking amplier is a must audition ampliers for music
lovers who understand that power is nothing without control.
Continuous power output (20Hz—20kHz at 0.5% THD), per channel
Both channels, 8Ω, 20Hz—20kHz 80W
Single channel, 4Ω, at 1kHz 175W
Harmonic distortion, 80% power, 8Ω at 1kHz 0.003%
Inputs
Phono (MM) cartridge:
Input sensitivity at 1kHz 5mV
Input impedance 47kΩ + 100pF
Frequency response (ref. RIAA curve) 20Hz - 20kHz ± 1dB
Signal/Noise ratio (Awtd) 50W, ref. 5mV input 80dB
Overload margin, ref. 5mV at 1kHz 23dB
Inputs:
Nominal sensitivity 1V
Input impedance 10kΩ
Maximum input 4.6Vrms
Frequency response 20Hz - 20kHz ± 0.2dB
Signal/noise ratio (Awtd) 50W, ref. 1V input 105dB
Preamplier output
Nominal output level 735mV
Output impedance 230Ω
Headphone output
Maximum output level into 600Ω
Output impedance
Load range
Accessory power output
2.1mm DC connector 6V, 500mA
General
Mains voltage 110-120V or 220-240V
Power consumption (maximum) 500W
Dimensions W x D x H (including feet) 433 x 275 x 85mm
Weight (net) 9.2kg
Weight (packed) 10.7kg
Supplied accessories Mains lead
E&OE
NOTE: All specication values are typical unless otherwise stated.
5V
1Ω
16Ω - 2kΩ
CR902 remote control
2 x AAA batteries
Accessory power cable
Available
Q3 2015
Arcam, The West Wing, Stirling House, Waterbeach,
Cambridge CB25 9PB, UK. www.arcam.co.uk
Preliminary information only. Arcam has a policy of
continuous improvement; we reserve the right to
change features without notice. E&OE 2015
Arcam is a trademark of A&R Cambridge Ltd. All other
trademarks are the property of their respective owners
Loading...