Ar blue clean AR141 User Manual
Assembly And OperAtiOns sheet
Ar141
Assembly
1
Cart Attachment
1
2
4
3
11
10
7
9
2
2. Install with supplied
screws. Tools needed 1
phillips screwdriver.
3
3. Insert lance adapter into the
gun push and turn clockwise to
positive stop as shown.
OperAtiOns
6
5
8
Package content:
1. Pressure Water Unit
2. Manual
3. Adjustable Spray Nozzle
4. Lance
5. Gun
6. Detergent Tank
7. Nozzle Cleaning Tool
8. High Pressure Hose
9. Garden Hose Fitting
10. Lance Holder
11. Cart Attachment
Gun Safety Button (D)
6
Pump
Hose
D
4 5
High Pressure Hose
Pump
5. Attach the high
pressure hose onto the
4. Press release button on
bottom of gun toward back of
the gun, then insert high pressure
pump water outlet by
turning clockwise and
hand tightening.
hose.
7
Safety Lock
1
Reset
8
6. a) Attach swivel adapter to
pump water inlet, if not already
attached. Notice the swivel
adapter is marked with the words
pump and hose. Make sure to
connect pump side of the adapter
to the pump water inlet to prevent
damage to the threads.
b) Attach garden hose to swivel
adapter side marked hose.
Trigger
2
7. Activate the lock by
holding the gun and push
the lock from left to right.
Squeeze trigger to make
sure the trigger does not
move. The saftey trigger
lock should be locked at
all times when pressure
washer is not in use.
8. a) Plug the power cord
into a grounded 120V outlet
and press the reset button as
shown.
b) THIS MUST BE DONE
EACH TIME THE UNIT IS
PLUGGED IN AN OUTLET.
OperAtiOns cOntinued
9
Off
On
10
9. Press to [-] for on press [o] for off.
11
11. The use of detergents can dramatically
reduce cleaning time and assist in the
removal of difficult stains. Some detergents
have been customized for pressure washer
use on specific cleaning tasks. These
detergents are approximately as thick as
water. The use of thicker detergents, such
as dish soap, will clog the chemical injection
system and prevent the application of the
detergent.
The cleaning power of detergents comes
from applying them to a surface and giving
the chemicals time to break down the dirt
and grime. Detergents work best when
applied at low pressure.
The combination of chemical action and
high pressure rinsing is very effective. On
vertical surfaces, apply the detergent
starting at the bottom and working
your way upward. This will prevent the
detergent from sliding down and causing
streaks.
High pressure rinsing should also progress
from the bottom to top. On particularly
tough stains, it may be necessary to use a
brush in combination with detergents and
high pressure rinsing.
10. Spray pattern
shape and intensity
can be changed by
twisting the spray
adjuster at the end of
the lance. Keep hands
clear of the front of
the lance to prevent
injury.
12
12. tO cleAn Out the nOzzle:
• Turn off the unit.
• Turn off the water supply. Relieve
any pressure trapped in the hose by
squeezing the trigger 2 - 3 times.
• Separate lance from gun.
• Rotate nozzle to the narrow stream
setting. This opens up the fan blades.
• Using the included tip cleaner, or an
un-folded paper clip, insert wire into
the nozzle hole and move back and
forth until debris is dislodged.
• Remove additional debris by backflushing water through the nozzle.
To do this, remove the lance from
the gun, place end of a garden hose
(with water running) to tip of nozzle
pushing water and debris out the back
opening of the lance.
Before triggering the gun, adjust the
nozzle to a wide fan pattern.
1. Place the nozzle approximately 4 - 5
feet away from the cleaning surface.
Then hold the nozzle at a 45° angle to
the cleaning surface. Trigger the gun.
2. Vary the fan pattern spray angle and
the distance to the cleaning surface
until optimum cleaning efficiency
is achieved without damaging the
surface.
A clogged or partially clogged nozzle can
cause a significant reduction of water
coming out of the nozzle and cause the
unit to pulsate while spraying.
Loading...