Professional Grade Products
Hudson Automatic |
Water Fill Valve |
Installation Instructions
Package Includes:
•Fill Valve
•Slide Plate with thumbscrew and 2 bolts
•Instructions for Use
care and maintenance
•Regular pond maintenance such as removing debris from the skimmer basket/net will help the WFV operate more efficiently.
•Winter preparation – The WFV will not operate during extended freezing temperatures. Simply turn off the water supply to the unit and disconnect 1/4" tubing from the WFV. To remove tubing from the quick connect fitting, hold in the socket on the fitting and pull tubing out.
•Float must be in a flat vertical position to work.
NOte
•Easy to Install, takes only a few minutes!
•Maintains a ponds proper water level
•Plastic housing protects float
•For use with Aquascape Designs’ skimmers
Features
The Hudson WFV includes fittings to connect to a 1/4 inch |
• 1/2” to 1/4” Irrigation Conversion Kit. Allows |
||||
poly tubing. The 1/4 inch poly tubing can be trenched over |
WFV to be connected to irrigation line. (sold |
||||
to a standard water spigot or connected to an irrigation |
|
separately, #827807) |
|
||
system by a professional irrigation specialist. |
|
• 1/4” x 100’ Poly tubing (sold separately, #29470) |
|||
Installing the Hudson WFV |
Water Fill |
|
Irrigation |
1/4” x 100’ |
|
Tools needed for installation: |
|
||||
Valve with |
|
||||
|
Conversion Kit |
Poly Tubing |
|||
• 5/32 inch drill bit |
quick connects |
Slide |
|||
(#827807) |
(#29470) |
||||
• Phillips head screwdriver |
installed |
Plate |
|||
|
|
||||
• Adjustable wrench |
|
|
|
|
|
Parts list for the WFV System |
|
|
|
|
|
• Fill valve with quick connects installed |
|
|
|
||
• Slide Plate with thumbscrew and 2 bolts |
|
Brass Quick Connect Water |
|||
• Brass Quick Connect Water Spigot Fitting |
|
||||
|
Spigot Fitting |
(#07000) |
|||
(sold separately, #07000). |
|
|
|||
|
|
|
|
Skimmer Installation
1) Measure down 3" inches from the top of the |
6) Adjust the WFV. Final adjustments to the fill valve |
||||
Signature and Classic series for proper hole |
|
should be made while the pump is operating and |
|||
location. The second hole should be 1" over. |
|
the water in the pond is at the desired level. Simply |
|||
2) Drill two 5/32” holes at the locations marked. |
|
loosen the thumbscrew and slide the unit up or |
|||
3) Hold the WFV with slide plate assembly to the |
|
down until the valve shuts off at the desired level. |
|||
|
The valve will shut off 3/4"-1" from the bottom of |
||||
inside of the skimmer and thread the two screws |
|
||||
|
the valve depending on pressure. Note: There will |
||||
from the outside through the holes drilled. |
|
||||
|
be a short delay in shut off the first time the valve |
||||
4) Lay the tubing through the cord relief and insert |
|
||||
|
is used while the control chamber fills with water. |
||||
into the quick connect fittings. For Classic series, |
|
||||
|
Retighten the thumbscrew. |
|
|||
drill a 9/32" hole in the back wall to run the |
|
|
|||
|
|
|
|
|
|
tubing through. Leave extra tubing inside the |
1 |
|
|
2 |
|
skimmer for adjustments. To remove tubing from |
|
|
|
|
|
the quick connect fitting, hold in the socket on |
|
|
|
|
|
the fitting and pull tubing out. |
|
|
|
|
|
5) Bury the 1⁄4" poly tubing to water spigot and connect using adaptor.
3 |
4 Water in |
5 |
6 |
|
|
|
Brass Quick |
|
|
|
Connect (sold |
|
|
|
separately) |
|
Water out |
|
Poly Tubing |
Item #29469.062006 |
©2006 Aquascape, Inc. • All Worldwide Rights Reserved |
MicroSnorkel™ Installation
1)On the outside of the MicroSnorkel™, measure 2” down and at least 1” over for proper location. The second hole should be 1” over. (Picture with slide plate)
2)Drill two of 5/32” holes at the location marked.
3)Hold the slide plate assembly to the inside of the MicroSnorkel™ and thread the
two screws from the outside through the holes drilled.
4)Run the tubing through the pipe discharge and insert into the quick connect fitting. To remove tubing from the quick connect fitting, hold
in the socket and pull |
1 |
the tubing out. |
|
5) Bury the ¼” poly |
|
tubing to water |
|
spigot and connect |
|
using adapter. |
|
2 |
3 |
4 5
Brass Quick
Connect (sold
separately)
Poly Tubing
Made in USA for Aquascape, Inc.
St. Charles, IL 60174 • Brampton,ON, L6T 5V7 www.aquascapedesigns.com
IDD 06064588-ADI B060504