Aquametrix IP80 User Manual

Model IP80 Series
by
Water Analytics
Aqua
Metrix
Aqua
Impeller Flow Sensor
Features
• Low-friction, long-life jewel bearings
• Single moving part
• Six bladed impeller
• Fully eld-repairable
• Choice of materials for compatibility with variety of chemicals
• Integrated Tee and sensor
• Fixed depth in tting ensures proper placement in pipe
• High level signal can be sent up to 2000 feet
• Each tting individually calibrated and marked with K-factor (Pulses per Gallon)
Description
The IP80 series are impeller type (or “paddlewheel”) insertion meters de­signed for use with a wide variety of liquids in pipe sizes 1/2” to 8”. Sensors are available in brass, 316 stainless steel, PVC, and polypropylene. Bodies are machined from a solid rod for maximum precision. High-quality jewel bearings and nickel-bound tungsten carbide shafts are used for extreme low friction and long life. The rotation of the rotor is detected by a non-drag Hall-effect sensor. Output is a current-sinking pulse (square wave), which can be sent long distances (up to 2,000 feet) without a transmitter. This signal can be connected directly to PLC’s, counters, and computer cards, as well as a variety of AquaMetrix controls and displays. For rate and total display, the Shark-120/240 controller or Shark TX/P trans­mitter (loop powered) models are compatible with IP80 series sensors. They can be mounted in either surface, pipe or panel congurations. The IP80 series require special ttings that ensure correct depth placement in the pipe. Fittings come in a variety of materials for compatibility with specic applications. Tee ttings are individu­ally wet-calibrated at the factory and marked with the K-factor (pulses per gallon). Saddle ttings must be eld­installed on the pipe and do not come wet-calibrated. K-factors for saddles are based on factory testing.
Applications
• Waste water ow
• Water Treatment systems
• Irrigation
• Groundwater Remediation
• Chemical Mixing
• Process cooling systems
• Neutralizaton Systems
• Process ow control
• Filtration systems
by
Toll free - 855-747-7623
www.WaterAnalytics.net
Metrix
Water Analytics
100 School Street
Andover, MA 01810
978-749-9949
Model IP80 Series Impeller Flow Sensors Technical Data
Materials
Sensor Body PVC, Polypro, Brass, or 316 SS Rotor PVDF Shaft Nickel-bonded tungsten carbide
(Ceramic optional) Bearings Ruby jewel O-Ring EPDM (Viton optional)
Pipe Size
IP81 1/2” to 3” (12 to 76 mm) IP82 4” to 8” (100 to 200 mm)
Maximum Pressure
PVC or Polypro 175 PSI (12 bar) at 75º Brass 200 PSI (14 bar) 316 SS 250 PSI (17 bar)
Maximum Temperature
PVC or Polypro 130ºF (55ºC)* Brass or SS 200ºF (93ºC)
Flow Rate 0.3 to 30 FPS (0.1 to 9 M/s) Accuracy 1-1/2% of full scale Signal Hall effect current sinking pulse Power 6-24 VDC, 2 mA Maximum Cur­rent Cable #22 AWG 3-con, 18 ft. (6m)
20 mA
Flow Range (GPM)
IP81
1/2” 3/4” 1” 1-1/2” 2” 3” 4” 6” 8”
0.28 0.5 0.8 1.9 3.1 6.9 12 27 47
Min
28 50 80 190 314 691 1200 2700 4700
Max
PVC/Polypro Working Pressure vs. Temperature
60º7 80º9 100º 110º 120º 130º 140º
200
150
P.S.I.
100
50
IP82
Order Information
Dimensions
PVC Tee
Size Dim. A
1.5” 19.2”
2” 19.9”
PVC Block Tee
Size Dim. B Dim. C
1/2” 1.50” 3.80”
3/4” 1.90” 4.00”
1” 1.88” 4.00”
Sensor Style
Impeller sensor ( 1/2” - 3”) 81
Impeller sensor ( 4” - 6”) 82
Sensor Material
PVC P
Stainless Steel S
Polypropylene Y
Brass B
Mounting Style
1/2” Tee tting 050
3/4” Tee tting 075
1” Tee tting 100
1.5” Tee tting 150
2” Tee tting 200
3” Saddle/Weldolet tting 300
4” Saddle/Weldolet tting 400
6” Saddle/Weldolet tting 600
Mounting Tee Material
PVC P
304 Stainless Steel (available only for 0.5” - 2”) S
Bronze (Not available for 6” pipes) B
www.WaterAnalytics.net 978-749-9949 Toll free - 855-747-7623 (855-pHProbe)
Loading...