Aquacal 135, 111, 101, 110, 156 User Manual

...

MODEL /

- and -

SERIAL NUMBER

Models:

100, 110, 120, 135 & 155

101,111,121,156

HEAT ONLY

and

HEAT - COOL

Additional Labels:

South Beach

Caribbean Fox Smart

Tropez

Multi-Language

(English-Spanish-French)

Pool & Spa Heat Pump

Owner’s Manual and Installation Guide

Attention Installer: This manual is purchaser’s property; leave with heat pump owner!

PN: LTP0030

3/17/08

NOTES

___________________________________________________________________________________

__________________________________________________________________________________

___________________________________________________________________________________

_________________________________________________________________________________

___________________________________________________________________________________

__________________________________________________________________________________

___________________________________________________________________________________

_________________________________________________________________________________

__________________________________________________________________________________

________________________________________________________________________________________

___________________________________________________________________________________

____________________________________________________________________________________

_________________________________________________________________________________

__________________________________________________________________________________

_________________________________________________________________________________

__________________________________________________________________________________

1-800-786-7751

TABLE OF CONTENTS

WELCOME TO THE TEAM ----------------------------------------------5

IMPORTANT FEATURES OF YOUR NEW HEAT PUMP ------------------ 6

HOW A HEAT PUMP WORKS ------------------------------------------ 7

SAFETY INFORMATION ------------------------------------------------ 8

QUICK START & STOP ------------------------------------------------- 10

HEATER CONTROLS ---------------------------------------------------12

Control Panel Layout -----------------------------------------------12

Buttons, Lights, and Display --------------------------------------12

Operational & Programming Codes -------------------------------- 13

Owner-Level Programming (complete) ---------------------------14

MAINTENANCE AND GENERAL OPERATION --------------------------18

General Maintenance-----------------------------------------------18

Safety During Cleaning Operations -------------------------------18

Maintaining Proper Water Flow ------------------------------------19

Controlling Water Chemistry -------------------------------------- 19

Controlling Irrigation and Storm Water Run Off ------------------ 20

Maintaining Clearances Around Heater ---------------------------20

(Continued on Next Page)

TABLE OF CONTENTS

(CONTINUED)

MAINTENANCE AND GENERAL OPERATION...CONTINUED:

Heating Tips--------------------------------------------------------21

- Heating in Cooler Weather --------------------------------------21

Pool/Spa Blankets-----------------------------------------------21

Pool & Spa Combination Heating ------------------------------- 21

Spa Set-Back Option -------------------------------------------21

Calculating Initial Heating Time-----------------------------------22

Seasonal Use & Shut Down ---------------------------------------- 23

- (Use) During the Swim Season --------------------------------23

- Freeze Protection and Winterizing Requirements--------------23

- Winterizing Procedure ------------------------------------------24

AquaCal Preventive Maintenance Program ------------------------ 25

TROUBLESHOOTING (No Op, No heat, Water from Unit) ------------26

Troubleshooting Flowcharts ----------------------------------------27

INSTALLER-SPECIFIC INFORMATION (Installation & Set Up) ------30

Installer-Specific Table of Contents -------------------------------31

CONTACTING THE FACTORY ------------------------------------------57

Welcome

to the

eam

Dear Owner:

ongratulations on your wise decision to make an AquaCal heat pump part of your home. Since 1981, AquaCal has maintained the worldwide lead in the

manufacture of swimming pool & spa heat pumps. Your new heat pump is not only a great investment, but also the most cost effective method available for heating pools and spas. For example, your heat pump is up to 400% more efficient than gas, and, when compared to electric resistance heat, your heat pump is nearly 600% more effective. You can rest assured your new heat pump is of the highest quality and efficiency, and is designed and built to provide years of trouble-free operation.

Moreover, should you ever require help in using or maintaining your heat pump, you will find AquaCal’s customer and technical support staff to be the largest, most qualified, and—of utmost importance—the most easily accessed customer service team in the pool & spa heat pump industry.

“You can rest assured

knowing your new heat

pump is of the highest quality and efficiency,

and is designed and

built to provide years

of trouble-free

operation.”

Important Features of Your

New Heat Pump

ThermoLink® Heat Exchanger

The heart of your heat pump is the patented ThermoLink® heat exchanger. One of the primary causes of premature heat pump demise is the failure of the heat exchanger. Ordinary heat exchangers are made from a cupronickel alloy. This cupronickel material is susceptible to attack from the sanitizers used in pools and spas and from other related water chemistry conditions. Once the heat exchanger fails, the heat pump is ruined. The ThermoLink water chemistry damage.

50% fewer moving parts than standard piston-type compressors. This equates to much improved reliability and improved efficiency. Scroll compressors are also much quieter in operation than their piston-type counterparts. And, while all AquuaCal heat pumps are known for their low operating noise levels, if yours is a SuperQuiet likely your heat pump will be quieter than any other item on the pool equipment pad.

heat exchanger tube is made from titanium, and is virtually impervious to

Scroll Compressor

model, it’s very

Digital Controller

Digitally-based microprocessor controls water temperature to within 1º Fahrenheit of set point. Controller also permits user to predefine different pool and spa water temperatures, and to prevent tampering by locking out controls via a pass code.

Corrosion-Proof Cabinet

The cabinet, being made from resilient, UV-Protected ABS material, has superior fade resistance and can never rust or corrode. You can expect the cabinet to retain a likenew appearance with only an occasional wash down and—if so desired—a quick waxing.

Heat & Cool Capability*

Puts you in full control, year round... Warms your pool or spa with the reliability and efficiency of our other heat pumps, but, with the flip of a switch, can also cool your pool or spa to refreshing temperatures during hot summer months. For cooler climates, Heat & Cool heat pumps offer unique advantages over passive defrost models. Please read more below...

Hot Gas Defrost*

Hot gas defrost heat pumps are uniquely equipped for an active defrost cycle. Active defrost involves directing hot refrigerant vapor to the heat collector, melting accumulated ice away in a matter of a few minutes... then right back to heating. Standard defrost heat pumps may remain “off in defrost” for extended periods during very cold weather. Because of their ability to continue to operate–even during freezing weather–hot gas defrost models extend the swimming season longer than any standard-defrost heat pump.

These features available in Icebreaker®and SuperQuietTM Models Only.

PLEASE READ FURTHER TO BECOME FAMILIAR WITH ALL THE FEATURES, THE SAFE

OPERATION, AND THE CARE OF YOUR NEW HEAT PUMP.

HOW A HEAT PUMP WORKS

THE FOLLOWING EXPLANATION IS PROVIDED TO HELP YOU IN UNDERSTANDING

WHAT TO EXPECT FROM YOUR HEAT PUMP

…

A Heat Pump Does Not Make Heat…

Heat pumps are so extraordinarily efficient because they do not need to produce heat in order to warm pool or spa water. Rather, heat pumps simply transfer heat from the outside air into the water.

If one considers Absolute Zero (the point where all heat is absent) occurs at -459º Fahrenheit, it becomes evident outside air, even at the relative cool temperature of 55º Fahrenheit, still contains large amounts of heat energy. It is that abundant heat energy a heat pump captures and places into your pool or spa.

...

EAT

EMOVED FROM

OOL

ARMED

ATER

OOL

ATER

ADEN

NTERS

EAT

SAFETY INFORMATION

Used and maintained properly, your heat pump will provide year-upon-year of safe and economical service. However, as with any mechanical or electrical device, to get the most from your heat pump–while insuring personal safety for you and others–certain operational and maintenance factors must be observed.

Likewise, excepting a few minor owner-capable maintenance items (explained later in this manual), repair and service of your heat pump must be performed only by experienced service personnel. Should you, the owner, suspect your heat pump is not performing properly, by referring to the section in this manual entitled: "Troubleshooting," you will be able to determine if a call for service is required. Your installer can be one source of service, or AquaCal Customer Support personnel stand ready to assist you at: (800) 786-7751. For questions concerning installation, modifications, operation, service and upkeep, please contact your installer or AquaCal Customer Support. Warranties may be voided if the heater has been used, maintained, or repaired improperly.

In addition to voiding the manufacturer’s warranty... unapproved installation methods, nonstandard modifications, poor or incorrect maintenance, service by unqualified personnel, or improper use of the heater may result in personal injury and/or property damage. For personal safety, and to avoid damage to equipment, follow all safety instructions displayed on the heat pump and within this manual.

Safety Signals

Throughout this manual the following two safety signals are placed where particular care is required. Please note "WARNING" relates to personal safety, while "CAUTION" signals promote avoiding damage to equipment.

Failure to heed the following may result in perma-

WARNING !

“Warning” signal appears in this manual where special attention is required for personal safety. (Specific instructions will appear in this box.)

CAUTION !

“Caution” signal appears in this manual where special care is required to avoid equipment damage. (Specific instructions will appear in this box.)

nent injury or death.

Failure to heed the following may result in equipment damage.

Notice: Heater NOT Repairable by Owner

Failure to heed the following may result in permanent

WARNING !

Heat pumps contain no owner-repairable components. Repairs must not be attempted by untrained and/or unqualified individuals. If service is deemed necessary, contact installing dealer or AquaCal Customer Support at (800) 786-7751.

injury or death.

Refrigerant Circuit Service Only by Qualified, EPA Certified Technician

Failure to heed the following may result in permanent

WARNING !

Heater contains refrigerant under pressure. Repairs to the refrigerant circuit must not be attempted by untrained and/or unqualified individuals. Service must be performed only by qualified HVAC technicians. Recover refrigerant before opening system.

injury or death.

Water Temperature Safety

Failure to heed the following may result in permanent

WARNING !

Prolonged immersion in water warmer than normal body temperature may cause a condition known as HYPERTHERMIA. The symptoms of hyperthermia include: unawareness of impending hazard, failure to perceive heat, failure to recognize the need to exit the spa, and unconsciousness. The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. In addition, persons having an adverse medical history, or pregnant women, should consult a physician before using a hot tub or spa. Children and the extreme elderly should be supervised by a responsible adult.

injury or death.

Water Chemistry Safety

Failure to heed the following may result in permanent

WARNING !

Improper water chemistry can present a serious health hazard. To avoid possible hazards, maintain Pool/Spa water per standards detailed later in this manual.

CAUTION !

injury or death.

Failure to heed the following can result in damage to equipment.

While your heat pump’s titanium-based heat exchanger provides nearly impervious protection against poor water chemistry, improper water chemistry may cause expensive damage to pump, filter, pool shell, etc. To avoid equipment damage, maintain Pool/Spa water per standards detailed later in this manual.

Getting Started

HEATING- QUICK START & STOP

This brief information is provided as an aide to installers, service personnel, and owners. The intent of this section is to provide rapid access to very basic operational information. Individuals who will be routinely using, installing, maintaining, and servicing this heat pump, are strongly encouraged to read this entire manual. Herein, the terms: Heat Pump, Heater, and Unit are used synonymously. These

instructions are intended for local control of a heat pump, independent of an external controller. Owners: if your installation includes an external controller, contact your installing dealer, or the external controller manufacturer, for external controller operating instructions.

These instructions are for quick-starting in the HEATING mode... Owners of Heat-Cool units, in order to utilize all features of their heater, will certainly want to also refer to: ming, beginning on page-14 of this manual.

1. Verify Electrical Power is Present at Heater:

A. Ensure that the unit has electrical power connected; the heater controller display should be

illuminated.

B. If the display is blank, be certain the electrical breaker, and heater disconnect, are switched to

“ON.”

C. For now, leave the water circulation pump OFF.

Owner Level Program-

2. Set the Heater Controls (Refer to Control Panel Layout, Pg-12):

OWNER- If heater is connected to a Call-Flex controller, also see “Selecting Call-Flex Pump Options,” located on page-17 of this manual.

INSTALLER- Is heater connected to an external controller? If so, see external controller information located on pages 41 and 44 of this manual.

A. The user/owner settings can be made without water flowing. Once the heater has electrical

power connected, with water not flowing, the display should read FLO.

B. Press the MODE button until the HEAT (HEA) indication displays. This action will enable the

remaining programming keys.

C. Using the POOL / SPA selector key, select the POOL mode. An illuminated POOL indicator

light, located on the left side of the display, will confirm the POOL control has been selected. If heating only a spa, using the DOWN arrow key, lower the POOL temperature until OFF is displayed; then proceed to Step-“E.”

D. Use the UP / DOWN arrow keys to set the desired water temperature for the POOL water.

E. If the heat pump will be used to heat a spa, use the POOL/SPA selector key to select SPA,

then use the UP / DOWN arrow keys to set the desired water temperature for the SPA. An illuminated SPA indicator light, located on the left side of the display, will confirm the SPA control has been selected. If heating only a POOL, using the DOWN arrow key, lower the SPA temperature until OFF is displayed.

F. The heat pump controls are now set to maintain the desired water temperature for the POOL

and/or SPA.

(Quick-Start & Stop Continued Next Page)

HEATING-QUICK START & STOP (continued):

3. To Begin Heating:

A. Verify MODE is set to: HEAT (HEA); then, depending on which body of water is to be heated,

use the POOL / SPA selector key to select POOL or SPA.

B. Position water valves to flow water from the pool or spa, through the heater, and back to the

pool or spa.

C. Start the water pump; the fan will start, and after 4-minute time delay the unit will begin

heating. The selected body of water will be brought to temperature and maintained per the setting determined previously in: “Set the Heater Controls.”

D. In operation, whenever the actual (displayed) water temperature falls below the desired set

point, after an initial time delay of 4-minutes, the unit will begin heating.

NOTE: THE HEATER CONTROLLER INCORPORATES AN ANTI-SHORT CYCLE TIME DELAY. SHOULD OPERATION BE

INTERRUPTED

4. Program Filter Pump Run Time:

Most pool/spa systems utilize a timer or multifunction controller to manage filter pump run times. If your system incorporates such a device, follow the instructions below:

A. It will be necessary to allow the filter pump to run continuously until the water has reached the

desired temperature. If a timer controls the pool filter pump, it will be necessary to override the timer to allow 24-hr. operation.

B. Once the desired temperature has been obtained (1-4 days), reset the pump control device.

Colder months require longer running times–generally eight to twelve hours/day.

C. A heat pump can only operate when the filter pump is running. Therefore, it may be

necessary–during cooler weather–to extend the water pump’s hours of daily operation. The increased run time is necessary in order to keep up with increased, weather-related heat losses.

, COMPRESSOR RESTART WILL BE DELAYED BY APPROXIMATELY 4-MINUTES.

5. Continuous Usage and Water Around Heater:

Condensation... After the heat pump has been operating for some time, water may be observed surrounding the heater. The moisture seen is condensation produced as a normal by-product of transferring heat from the air into the pool or spa water. Quantities of 6-8 gallons of water produced per hour are common if the air humidity is high. Conversely, a low humidity condition may result in no condensation being produced. (If water around unit seems excessive, to troubleshoot, see page-26, “Water Coming from the Heat Pump.”)

6. To Stop the Heat Pump:

A. Select: OFF via the MODE selector. This method of shut down preserves the controller

settings;

B. An interruption of water flow–such as when a pump timer is in control–will also halt heat

pump operation.

(End...Quick-Start & Stop)

HEATER CONTROLS

Control Panel Layout

(APPEARANCE VARIES BY MODEL)

Control Buttons, Indicator Lights, & Display

(AS INDICATED BY CIRCLED NUMBERS)

1) POOL / SPA SELECTOR – Selects either pool or spa thermostat.

2) COOLING INDICATOR LIGHT – Indicates unit is cooling. (Note: this light

nonfunctional with heat-only models.)

3) UP ARROW – Increases temperature setting. (Maximum setting is 104

4) DOWN ARROW – Decreases temperature setting. (Minimum setting is 45

5) HEATING INDICATOR LIGHT – Indicates unit is heating.

6) MODE SELECTOR – Used to select between the Heating, Cooling, Auto-

Changeover, and Off for Heat & Cool models. Used to select between Heating and Off for heat-only models.

7) SPA INDICATOR LIGHT – Indicates heater is referencing spa thermostat.

8) POOL INDICATOR LIGHT – Indicates heater is referencing pool thermostat.

9) LED DISPLAY – Displays water temperature when no keys are being pressed.

Displays desired temperature when UP ARROW or DOWN ARROW is pressed. Also displays operational, programming, and fault codes as applicable.

10) DESIRED TEMPERATURE LIGHT – Indicates temperature set point is being displayed. Indicates temperature set point is being changed due to the UP ARROW or DOWN ARROW being pressed.

11) WATER TEMPERATURE LIGHT – Indicates current water temperature is being displayed.

HEATER CONTROLS...continued

Operational & Programming Codes

HE FOLLOWING CODES WILL BE DISPLAYED AS PART

OF THE NORMAL OPERATION OF THE HEATER

FLO..... No Water Flow Detected. This code appears whenever the circulating pump is off, or when

the heater is not receiving correct water flow.

OFF..... System is Off. This code appears whenever heater has been turned off via the mode

selector button, or when the temperature set point has been lowered below 45

CFI...... Celsius/Fahrenheit Selection. This is a programming entry point to select in which format

the water temperature will be displayed.

ULC..... User Lock Code. This is a programming entry point; when activated, steps to the next

menu level: ELC.

ELC..... Enter Lock Code. This a programming entry point; permits end user to select a secret

code, thereby limiting access to the owner settings.

CFO..... Call Flex Options. This is a programming entry point; when used in conjunction with an

AquaCal Call/Flex add on kit, permits the use of CALL or FLEX options.

FS....... Heater in Defrost Mode (Applicable to Heat-Only Units, only). This code appears as a

normal display during periods of lower air temperatures. Sequence follows:

Heat-Only Defrost Sequence: Fan continues to run and compressor is off. Compressor will restart when air coil temperature rises to approximately 38°F.

LOC..... This is a Service Entry Point (not intended for use by the owner). The[LOC] code permits

service personal to enter a factory code for access to adjustable calibration and sitedependant setup parameters. Service adjustments are available to authorized installation and service personnel, only.

CAUTION !

Heat pumps contain no owner-serviceable components. Owner-initiated adjustments, beyond the controller “LOC” code, must not be attempted. If adjustments are deemed necessary, the owner should contact installing dealer or AquaCal Customer Support at (800) 786-7751.

Failure to heed the following may result in equipment damage and voiding of manufacturer’s warranty.

HEATER CONTROLS...continued

Start Up & Setting Operating Controls

Owner-Level Programming Instructions (Complete)

Covered within this section are features and settings typically accessed first by the installer, and then remaining accessible by the end user (the owner). These features reside at the Level-1 access point within the microprocessor. Note: if preferred, all programming may be performed with waiting to start the water pump as the last step in the set up and run process.

1. Applying Power to The Controller:

A. When power is first applied, the controller performs a lamp test and the display will read

[888]. Following [888] the software version will display briefly.

B. The control will then display the actual water temperature, provided the circulating pump is

operating, and adequate water is flowing through the heater.

C. If the pool-circulating pump is off, the control will display: [FLO]. This code message

indicates no (or insufficient) water is being circulated through the heat pump.

2. MODE Controls Explained, and Starting the Heat Pump:

A. Once electrical power is supplied to the heat pump, sufficient water is circulating, and the

heater controller has successfully completed its self-test, the heater is ready to operate.

out water flow,

B. The heat pump is shipped with the controller [MODE] function set to “OFF”. There are two

ways to switch the heat pump OFF: button is “OFF”. below the minimum temperature setting (45oF); this action will cause the display to read “OFF”. To switch the unit ON, first use the mode button to select the HEAT mode—for Heat Only models—or, if the heat pump is a Heat and Cool model, use the mode button to select one of the following modes: HEAT, COOL, or ACH (Auto-Changer Over). In the [OFF] mode, the actual water temperature will be displayed as long as the circulating pump is operational and correct water flow is present. In the event water is not circulating through the heat pump (or flow is insufficient), the controller will display the [FLO] (No Water Flow) code message.

C. Using the UP ARROW key, increase the desired temperature until it exceeds the value of the

actual temperature displayed. (Note: See # “8,” later in this section, if “000” is displayed upon pressing either the up or down arrow keys.) Once the desired temperature has been entered, the display will read the actual temperature and the heat pump will start to operate. Both the compressor and the fan must be operating before the “Heating” LED will illuminate. (Note: When MODE function is OFF, the current water temperature will be displayed; no functions, values, or programming will be available for adjustment.)

3. Turning The Heat Pump Off:

Method 1: using the [MODE] key, press the key until the display reads “OFF” The heater will shut off and remain off until the [MODE] key is used the select an operational mode. This is the preferred method for shutting off the heat pump.

Second Method- The thermostat set point can be lowered to a position

First Method- One of the functions of the [MODE]

Method 2: using the DOWN key, press the key until the desired water temperature reaches 45oF (minimum setting); then, press the DOWN key one more time, causing the display to read “OFF”. This method is typically used in conjunction with 2-wire external controllers; these controllers are equipped with their own thermostats.

(Continued on Next Page)

HEATER CONTROLS...continued

Start Up & Setting Operating Controls

Owner-Level Programming Instructions... continued:

4. Selecting Pool/Spa Thermostat Settings:

A. Press the [POOL/SPA] key to toggle between the pool and the spa temperature set points.

B. The pool/spa LED indicator lights, located to the left of the temperature display, will confirm

the selected set point.

5. Changing The Pool Temperature Set Point:

A. Using the [POOL/SPA] key, select the POOL temperature set point. The pool set point

indicator light will confirm the selection.

B. The pool temperature set point is adjustable from a minimum of 45

104oF. Pressing the [UP ARROW] key will raise the set point 1-degree for every push of the button. Pressing the [DOWN ARROW] key will lower the set point 1-degree for every push of the button.

6. Changing The Spa Temperature Set Point:

F to a maximum of

A. Using the [POOL/SPA] key, select the SPA temperature set point. The spa set point indicator

light will confirm the selection.

B. The spa temperature set point is adjustable from a minimum of 45

F to a maximum of 104oF. Pressing the [UP ARROW] key will raise the set point 1-degree for every push of the button. Pressing the [DOWN ARROW] key will lower the set point 1-degree for every push of the button.

7. Selecting Between

F and oC:

A. Simultaneously press and hold both the [UP ARROW] and [DOWN ARROW] keys until

[CF1] (Celsius / Fahrenheit) code appears.

B. With the [CF1] code displayed, pressing the [UP ARROW] or [DOWN ARROW] keys will

change the selection code to either “0” or “1”. Select “1” for Fahrenheit temperature display, or “0” for Celsius temperature display. Once the desired temperature display mode has been selected,

not pressing any buttons for 15-seconds will allow the controller to save the selection and return to the normal operating mode. Pressing the {POOL/SPA] key will also save the selection and step to the next menu parameter: [ULC] (User Lock Code).

8. User Lock Code Option [ULC]:

This Option Explained:

Heat pumps are shipped from the factory with the [ULC] option disabled. Enabling the [ULC] function permits the heat pump owner to restrict access to the unit’s controls. With the [ULC] function enabled, unless the correct ULC code number is entered, changes to Level-1 programming are not possible. (I.e.: Altering temperature set points, Pool/Spa selection, C/F display changes, etc., will not be possible). The [ULC] option can be thought of as an electronic lockable cover for the controls.

(Continued on Next Page)

HEATER CONTROLS...continued

Start Up & Setting Operating Controls

Owner-Level Programming Instructions... continued:

8. User Lock Code Option [ULC]...continued:

A. Selecting ULC Option:

1) Press either the UP or DOWN ARROW keys; if “LOC” is momentarily displayed followed by “0”, the ULC feature is enabled. If “0” displays proceed to “6)” of this section; otherwise, see number “2,” below.

2) Simultaneously press and hold both the [UP ARROW] and [DOWN ARROW] keys until [CF1] (Celsius / Fahrenheit) code appears.

3) Press the [POOL/SPA] key once to display [ULC].

4) With [ULC] displayed, pressing either the Up or Down Arrow key will display either “1” or “0”. Selecting “0” will allow the keypad to remain unlocked. Selecting “1” will enable the User Lock Code option. Then, to enter a lock code number, press the [POOL/SPA] key once to display [ELC] (Enter Lock Code).

5) With [ELC] displayed, use the Up or Down arrow keys to select a lock code. The code can be any number from “00” to “99”. The factory set lock code is “0”. Not pressing any buttons for 15-seconds will allow the controller to save the selection and return to the normal operating mode. Pressing the {POOL/SPA] key will also save the selection, and will step the controller to the next menu parameter: [CFO] (Call Flex Options).

6) Once the ULC option has been enabled, pressing any key will momentarily display “LOC” followed by “0” (prompting the entry of the correct lock code number). To gain access to the controller:

a. Using the [UP ARROW] key, scroll to the correct lock code number, then;

b. Press the [POOL/SPA] key… Current water temperature will be displayed… Control

setting can now be viewed or changed as desired.

c. After a period of approximately four (4) minutes, during which time no buttons have

been pressed, the controller will automatically return to the locked mode. Provided ULC selection is set to “1,” the controller will always fail-safe in the locked mode.

d. Without knowledge of the correct lock code, and with the ULC enabled, control

adjustments will place. The lock code may be changed any number of times by following the instructions detailed in this section.

B. De-Activating the User Lock Code [ULC] function:

1) Following the instructions detailed previously at: “8, 6)”, press any key and enter the user lock code number; then press the [POOL/SPA] key.

2) Immediately following the entry of the user lock code, simultaneously press and hold the [UP ARROW] and [DOWN ARROW] keys until the code [CF1] appears on the display.

3) Then, use the [POOL/SPA] key to scroll to the [ULC] message; press the [DOWN ARROW] key to change the display to “0”. This will disable the User lock function.

not be possible. Be certain to record your lock code in a safe

(ULC Continued on Next Page)

HEATER CONTROLS...continued

Start Up & Setting Operating Controls

Owner-Level Programming Instructions... continued:

C. User Lock Code is Activated, but Pass Number is Not Known (“Back Door Entry”):

Note: Should the ULC option be enabled, and a lock code number other than the factory default (0) be installed but is unknown, the following procedure may be followed to regain controller programming access:

1) Simultaneously press and hold the [POOL/SPA] and [UP ARROW] keys until the display

shows “888”. This operation will reset the controller to the factory default settings.

2) When reset to the factory default settings the user lock code [ULC] is deactivated and

the user lock code number [ELC] is reset to “0.”

3) In addition, all other settings are returned to the factory defaults. If an external

controller is in use, contact AquaCal Technical Support Group (800-786-7751); ask for assistance with re-configuring the controller for use with an external controller.

9. Selecting Call-Flex Pump Options [CFO]:

General Information:

The Call-Flex option automatically adjusts the run time of the water circulator pump, and heater, based upon changing weather conditions. Without Call-Flex, as weather conditions grow progressively cooler during winter months, or when unusually cold weather occurs, the run duration of the circulator pump may require manual adjustments to permit the heater to maintain or reattain desired water temperature (the water pump must be running in order for the heater to operate). Likewise, without Call-Flex, one must remember to reset the pump run controls following the cold weather event. The Call-Flex option greatly reduces the need for seasonal, manually-made, pump run time adjustments. Call-Flex is a dealer-installed option that does not come with every heater; if unsure, check with the installing dealer to determine if a call-flex kit was part of the original installation.

to have Call-Flex added, your dealer can do so...contact the installing dealer.

If the installation is equipped with the Call-Flex option, the following steps are used to control the Call-Flex features:

A. Simultaneously press and hold the [UP ARROW] and [DOWN ARROW] keys until the

display shows “CF1”. Press the [POOL/SPA] key three times to scroll the display to [CFO].

B. With the [CFO] (Call-Flex Options) code displayed, use the Up or Down keys to select “0” to

disable the Call Flex Options, “1” to enable the Call Option, or “2” to enable the Flex Option. Not pressing any buttons for 15-seconds will allow the controller to save the selection and return to the normal operating mode. Pressing the {POOL/SPA] key will also save the selection, and will step the controller to the next menu parameter: [LOC] (Service Lock Code).

If Call-Flex was not part of the installation, and you would like

C. For further information, please refer to Call-Flex installation instructions, shipped with the

Call-Flex kit. For additional copies of these instructions, contact the AquaCal Customer Support (800-786-7751).

(End... Owner-Level Programming Instructions)

MAINTENANCE

OPERATIONAL RECOMMENDATIONS

The information in this section is written primarily for the Home Owner, but may also apply to servicing dealers or HVAC service centers. This section contains information concerning planned maintenance, proper water flow, maintaining proper clearances, as well as other vital information. Please read this section now, and before calling AquaCal Customer Support (800-786-7751).

General Maintenance

Heat pumps should be inspected and maintained on an annual basis by a qualified swimming pool heat pump specialist. Additionally, if the heat pump is located near the beach or coastal area, where salt spray and sand can become detrimental factors, more frequent service may be necessary. For service plan information, please see: contact AquaCal Customer Support at: 800-786-7751.

Planned Maintenance Program, later in this section, and then

While annual maintenance is recommended to maintain your warranty, if you choose in the Planned Maintenance Program, rinsing the air coil regularly, and keeping the base of the unit clear of leaves and debris is a necessity.

Should you as the owner desire to perform the coil rinsing and other cosmetic care of the heat pump, please contact AquaCal Customer Support: 1-800-786-7751; request the document titled: “ Care for Air-Source Heat Pumps: Approved Method for Home Owners.”

not to participate

Appearance

Safety During Cleaning Operations

Failure to heed the following may result in permanent

WARNING !

POSSIBLE ELECTRIC SHOCK HAZARD . . . Should you decide to wash the heat pump via water hose, disconnect all power to the pool equipment pad- including, but not limited to: The heat pump, water pump, and any and all other electrical equipment. Do NOT spray water directly into electrical components. Do NOT restore electrical power until such time as all water has dried completely.

injury or death.

Failure to heed the following may result in damage to

CAUTION !

Do not use a pressure cleaner to wash heat pump . . . . Damage to evaporator fins, as

well as other components, will result.

equipment.

MAINTENANCE

& OPERATION (continued)

Maintain Proper Water Flow

• It is important to operate and maintain the filter according to the manufacturer's specifications. As a filter gets dirty, the water flow to the heat pump is reduced. The higher the pressure on the filter gauge, the lower the flow rate.

• Similar to a dirty filter, large amounts of debris in the pump and skimmer baskets can reduce water flow. Keep baskets free of debris.

• Check for improper valve settings. A partially closed valve after the filter, or a full-open bypass around the heater, will cause insufficient water flow through heater.

• If the conditions listed above remain unresolved, the water flow through the heater may be reduced to a point where internal safety devices (i.e.: “HP” or “HP5”) shut the heater off.

• Before calling for service, always check the filter, the pump basket, and water valve positions. If the problem persists, please call AquaCal Customer Support at: (800)786-7751.

Control Water Chemistry

• IMPORTANT! Your heat pump is engineered for exceptional durability and reliability. And, this

unit’s heat exchanger—being equipped with titanium tubing—will be nearly impervious to water chemistry damage. However, other components of the heater, and the remainder of the pool/spa equipment in general, may be susceptible to damage from prolonged exposure to unbalanced water chemistry. Likewise, bathers may be exposed to health risks if water chemistry is not properly maintained.

• For the longevity of the entire pool/spa installation, and for the safety of bathers, it is strongly

recommended the water chemistry be checked regularly and maintained within proper norms. Please see the table, below, for a complete listing of recommended water chemistry levels.

RECOMMENDED WATER CHEMISTRY STANDARDS*

Chlorine . . . . . . . . . . . ........ . . .:

Bromine . . . . . . . . . . . . ........ . .:

pH . . . . . . . . . . . . . . . . . . ..........:

Total Alkalinity . . . . . . . . . ........:

Calcium Hardness . . . . . . . .....:

Total Dissolved Solids . . . . .....:

* STANDARDS FOR COMMERCIAL APPLICATIONS MAY VARY LOCAL-TO-LOCAL...

ALWAYS MAINTAIN WITHIN LIMITS ESTABLISHED BY AUTHORITY HAVING JURISDICTION.

CAUTION- Pool/Spa Refinishing Operations

During pool refinishing or acid cleaning, the water flow through the heater must be shut off. Water flow to the heater must remain off until water chemistry is once again in balance and the water is clear in appearance. Failure to follow these instructions may void heater warranty.

1.0 – 3.0 ppm in pools, 1.5 – 3.0 ppm in spas

2.0 – 4.0 ppm in pools, 3.0 – 5.0 ppm in spas

7.4 – 7.6 ppm in pools, 7.2 – 7.8 ppm in spas 80 – 140 ppm in pools, 80 – 120 ppm in spas 200 – 400 ppm in pools and spas 1,000 – 2,000 ppm in pools, 1,500 ppm above start-up TDS in spas

MAINTENANCE

(

)

& OPERATION (continued)

Control Irrigation and Storm Run Off

• Control Irrigation: In regions were wells are used for irrigation, water quality is sometimes poor, and water spray can damage heater components. Regardless of water quality, it is important that irrigation be directed away from the heat pump.

• Prevent rain water runoff from pouring directly into the heater. The heater is designed to withstand normal rainfall, but solid streams of water from roof drip-lines may eventually damage heat pump components.

• If the heat pump resides beneath a roof edge, to promote heat pump longevity, a rain leader (gutter), or rain shield, will be necessary.

Maintain Proper Clearances Around Heater

• For maximum efficiency, proper air flow clearances around heater must be maintained.

• It is important to keep the area immediately adjacent to the heat pump clear of items such as

shrubs and bushes, lawn furniture, chemicals containers, etc. These items can prevent air from circulating fully through the heater, and will result in inefficient operation or damage to the heat pump.

• In addition, do not place objects on top of the heat pump; doing so will block the air from exiting

the heater, and will result in damage to the compressor and fan motor.

• Proper clearances are also necessary in order to access the working parts of your heater. A

heater that is easy to "get to," will be a heater that is easy to maintain; service and maintenance personnel will thank you for keeping the area around your heater unobstructed.

• Please see diagrams, below, for specific clearance requirements.

AINRUN-OFF

UST BE DIRECTED

WAY FROM

EATER

30” M

LEARANCE

VERHANG WITH

UTTER

INIMUM

, F

RONT

5FT. M

INIMUM CLEARANCE

VERHEAD

SQ MODELS, 12-INCHES

ALL OTHER, 6-INCHES

6” M

INIMUM CLEARANCE

(REAR)

SQ MODELS, 12-INCHES; ALL OTHER, 6-INCHES

12-

NCHES

(

SIDE

)

NCHES

6-I

(REAR)

EAR

30-I

NCHES

(

FRONT

12-

NCHES

SIDE

(

)

SIDE VIEW (NO SCALE)

FRONT-REAR-OVERHEAD

TOP VIEW (NO SCALE)

FRONT-SIDES-REAR

MAINTENANCE

& OPERATION (continued)

Heating Tips

Heating in Cooler Weather...

Late night and early morning, generally being the coolest times of the day, are least efficient for heating. For most efficient heating operation, heat pumps should be timed to operate during the warmest, daylight portions of the day. Conversely, if cooling a pool, it is best to run the equipment at night. Please set water pump and heat pump controls accordingly.

Pool/Spa Blankets...

A “solar” blanket will significantly reduce your heating bills. Check with the installing dealer to see if your heat pump was sized to be used in conjunction with a blanket. Blanketed pools will typically lose only 3 - 4° of heat per night versus 8 - 10° overnight with an un-blanketed pool. Reductions of 40-60% on heating bills can be achieved by using blankets. (Idea...Contact AquaCal Customer Support (800-786-7751) to learn about Liquid Blanket innovations.)

Failure to heed the following may result in permanent

WARNING !

injury or death.

Improperly used, Pool-Spa blankets can become a drowning risk to people and pets. Blankets are not safety covers. They are not designed to support the weight of a person or pet. Never enter a pool until the blanket is completely removed (under no circumstances should anyone swim under the blanket). Follow all safety recommendations of the blanket manufacturer.

Pool and Spa Combination Heating...

Everything stated for heating a pool applies for heating a spa—only the volume of water being heated is different. Your heat pump comes equipped with two thermostats. One thermostat is for the pool and the other is for the spa. Simply position the pool and spa isolation valves as directed by your installer; select the appropriate thermostat (pool or spa), whichever you are heating, and with electrical power and water flow supplied to the heater, the water will be maintained at set point.

Your system can be automated with the addition of an optional Using this option will save you from having to change the thermostat selector switch each time you change from pool-to-spa and back again. Or, add a Universal Heater Controller (P.N. 0097TS) and gain not only automatic thermostat switching, but also automated spa/pool water valve operation. For details, contact the installer, the distributing dealer, or AquaCal Customer Support (800-786-7751).

External Flow Switch Kit (P.N. 0040S).

Spa Heating & Spa Setback Option...

Air blowing into your spa, while it is being brought to temperature, will very often neutralize or partially counteract the heat being put into the spa by the heater; this added heat loss equates to increased time to bring your spa to desired temperature. When heating a spa, be sure to turn off the air blower. Air induced through the spa jets should also be eliminated, during warm-up, whenever possible.

If your heater is being used to only heat a spa, the simply set the pool control at a point 10-15º F below desired spa heat temperature and select the pool thermostat. This method allows the spa–when not in use–to be held at a heated temperature, but somewhat lower than normal spa-use temperature. One would want to blanket the spa if using this setback method. Using spa setback will result in reduced warm up periods over full, cold starts.

POOL thermostat can be used as a setback control:

MAINTENANCE

& OPERATION (continued)

Calculating Initial Heating Time

The time it takes to initially warm your pool or spa depends on several factors.

First, determine how many gallons of water are to be heated. Knowing this, you can then compute the equivalent pounds of water involved, and the BTU's necessary to heat the volume of water to the desired temperature.

Next, find the approximate BTU output of your heat pump at the current ambient air temperature; see product literature at: www.aquacal.com, or contact AquaCal Customer Support (800-786-7751).

Finally, decide upon the temperature at which you plan to maintain your pool or spa.

The following work sheet can be used to calculate approximately how long it will take your heater to bring your pool or spa up to temperature. Keep in mind heating times will vary somewhat due to weather conditions during the period that the heater is in use; use of a pool blanket can dramatically improve heat up and heat maintenance performance.

Pool Volume (Length X Width X Average Depth) = _________ Pool Cubic Feet

X Gallons per cubic ft.(7.5) = _________ Pool Gallonage

X Pounds per Gallon (8.3) = _________ Pounds of Water

How many degrees do you want to raise the temperature of the pool?

# of Degrees _________ X Pounds of Water (per above) = __________ BTU’s Required

BTU’s Required (per above) ________

Optional Cold Weather Adjustment Factor:

Hrs. of Operation (per above) ______ X 1.25 (60º F outside air (O.A.) Temperature Factor) =

______Hrs. of Operation at 60º F O.A.

÷ BTU Output of Heater = ______ Hrs. of Operation

At Start Up: Continuous Circulator Pump Operation Required

When starting a heat pump for the first time, it must be permitted to operate, continuously, until the desired water temperature is attained. This may take several hours, to several days, depending upon the size of the pool or spa and weather conditions.

If a time clock or similar device controls the operating times of the water circulating pump, temporarily override the water pump controller, allowing for 24-hour, continuous water pump operation.

Once the body of water has reached the desired temperature, the water pump controller can be reset.

MAINTENANCE

& OPERATION (continued)

Seasonal Use & Shut Down

During the Swim Season:

• During the swim season, even if the pool or spa is not in use, allow water to flow through the

heater. Doing so eliminates the need to reposition valves when you do wish to heat the pool or spa.

• During periods when heating or cooling is not desired, leave heater controls in the OFF position.

Important !!!

Information Critical to the

Survival of Your Heater

Follows...

Freeze Protection & Extended Shut Down:

In areas where freezing conditions are a rare occurrence, allow the filtration system to run continuously throughout the freeze period. Typically, during light freeze conditions, circulating (moving) water will not freeze.

In areas where freezing conditions are prevalent and sustained, the heat pump ized; please refer to winterizing instructions, below, and on the following pages.

Winterizing for Hard Freeze Conditions:

CAUTION !

Failure to properly winterize heat pump may result in serious equipment damage. Freeze damage is not covered under the heat pump warranty.

CAUTION !

While the plumbing connections are in the winterized condition (not fully tightened), it is imperative pool/spa water loose plumbing connections may result in damage to circulating pump, pool/spa structure, and/or other equipment.

not be circulated through the heat pump. Loss of water through

Failure to heed the following can result in damage to equipment and/or property.

MUST be winter-

(Winterizing continued on page following)

MAINTENANCE

& OPERATION (continued)

Winterizing Procedure:

1. Disconnect all electrical power to the heater; turn OFF circulating pump.

2. At the two (2) connection unions, disconnect the plumbing to the heater (removal is counterclockwise).

3. Locate the hand drain plug at lower, front corner of heater. See figure below. (position may vary between models). Remove plug.

4. Permit all of the water to drain out of the condenser and then replace the plug; thread the plug in clockwise until just snug, then apply an additional 1/8 turn.

5. To prevent insects and vermin from entering the plumbing during the winterized period, partially reconnect the two (2) plumbing connection unions: couple each union one or two threads; this will permit condensation to drain, but will prevent most insects and animals from entering the plumbing circuit.

Next Season: To ready the heat pump for use, simply retighten plumbing connection unions.

6. Hand-tight is generally sufficient.

LOCATION OF EXTERNAL DRAIN PLUG

CAUTION !

-EXACT LOCATION

WILL VARY BY MODEL-

Failure to heed the following can result in damage to equipment and/or property.

While the plumbing connections are in the winterized condition (not fully tightened), it is imperative pool/spa water not be circulated through the heat pump. Loss of water through loose plumbing connections may result in damage to circulating pump, pool-spa structure, and/or other equipment.

MAINTENANCE

& OPERATION (continued)

Planned Maintenance Program

Just as you would have yearly service performed on your air-conditioning system, regular inspection and maintenance of your AquaCal heat pump will insure highest operating efficiencies. A regularly maintained heater will protect your investment, and will potentially extend the useful life of your heat pump far beyond the warranty period. Our expertly trained factory service technicians offer comprehensive maintenance procedures designed to insure your heat pump–over the coming years–will continue to operate efficiently and reliably.*

The 20-Point Planned Maintenance Service Includes the Following:

> Check Water Flow

> Clean Evaporator Coil

> Check Relay Contacts

> Check Capacitor Values

> Check Refrigerant Levels

> Clean Heat Pump Cabinet

> Check Fan Blade Clearances

> Check Flow/Pressure Switch

> Check Electrical Connections

> Check Proper Voltage To Unit

> Oil Fan Motor (As Applicable)

> Check Fan Motor Amperage Draw

> Check Pool & Spa Water Chemistry

> Check and Clean Condensate Drains

> Check Compressor Amperage Draw

> Check Water Pump Amperage Draw

> Acid Wash Source Coil (As Applicable)

> Check Air Temperature Change Through Evaporator

> Check Operating Controls and Temperature Sensors

> Check Water Temperature Change Through Condenser

We recommend Preventive Maintenance be performed starting one (1) year after the installation of the

heater.

* FACTORY PM SERVICE NOT AVAILABLE IN ALL REGIONS; PLEASE CONTACT AQUACAL CUSTOMER SUPPORT FOR ADDITIONAL

INFORMATION

(800) 786-7751.

TROUBLESHOOTING

Heat Pump Fails to Operate...

Is the display illuminated?

If not, ensure the main breaker (located at the power supply panel) and the disconnect switch (located near the heat pump) are both turned ON.

Is the code “FLO” displayed?

If so, check to be sure that the circulating pump is operating and the filter is clean. There may also be a valve positioned incorrectly allowing water to bypass the heat pump. Be sure water is flowing through the heater.

Is the Pool or Spa thermostat selected for the correct body of water to be heated, and have you tried selecting a higher temperature setting?

If not, the actual water temperature may be above that of the selected thermostat. Raise the desired water temperature above the actual water temperature; the fan should start, and after approximately four (4) minutes, the “Heating” light should illuminate. If the heat pump still fails to start, and the unit is not in defrost (heat-only unit defrost display code is: “FS”), contact AquaCal Customer Support: 800-786-7751.

Also see page 51...

“Error Codes”

Heat Pump Running... but is it Heating?

Is the air blowing out of the top of the unit noticeably cooler than the surrounding air?

(With heating indicator light illuminated, a 9°F to 12°F difference is typical.) If not, contact AquaCal for service at: 800-786-7751. But first, be sure all air coil surfaces are free from obstructions– low roof overhangs, landscaping, walls, fences, etc., can restrict air flow. The heat pump needs good airflow to operate at peak efficiency.

How many hours/day does the circulating pump operate?

Cooler weather conditions, or heating to a higher than normal temperature, may necessitate running the heat pump for a longer period of time. Was the heater sized considering the use of a pool blanket (check with installing dealer)? A blanket can be useful in permitting shorter run times, in turn leading to substantial energy cost savings.

What is the outside air temperature?

The heat pump may be in the defrost mode if air temperatures are below 50°F. With Heat-Only models, if the heater is in defrost, the code: ”FS” will be displayed. If air temperatures are not cold, but the heater remains in defrost, contact AquaCal Customer Support at: 800-786-7751.

Water Coming from the Heat Pump...

Is it a leak or just condensation from normal operation? Here's how to find out.

Test the water draining out the heater base for the presence of the sanitizer being used in the pool or spa. Using a water test kit, or a test strip, check a sample of the water for chlorine or bromine. If the sample tests positive for sanitizer, call AquaCal for service at: 800-786-7751. If the test is negative, the water is probably harmless condensate.

Or, as an alternate method, shut the heat pump off, leaving the circulation pump running. Within a few hours, there should be a marked reduction in the amount of water seen around the bottom of the heat pump. If the water appears to be drying up, the water is probably harmless condensate, indicative of normal operation.

NOTE: The water test method will

produce the sanitizing agent.

CAUTION! If after testing, a water leak is suspected, immediately shut OFF the water pump and

contact AquaCal Customer Support: 800-786-7751.

not be effective if an ionizer or ozone generator is being used to

TROUBLESHOOTING FLOWCHART

Display is illuminated. If

"FLO" is dis play ed,

check to be s ure the

check to be sure the

circulating pump is

operating and the f ilter

circulating pump is

is clean. There m ay

operating and the f ilter

is clean. There m ay

also be a valv e

positioned incorrectly.

Be certain water is

f lowing through the

Be certain water is

heater.

f lowing through the

heater.

Heat Pump Fails to Operate

START

Yes No

Isthe Display Illum inated?,

START

Isthe Display Illum inated?,

If not, ensure the main

breaker (located at the

power supply panel)

breaker (located at the

and the disc onnect

power supply panel)

and the disc onnect

switch (locat ed near

the heat pump) are

both turned ON .

Problem

Solved.

(Verif y water

temperature

(Verif y water

temperature

settings are as

desired.)

Yes

Is the heater

operating correc tly ?

operating c orrect ly ?

Is the heater

operating correctly ?

Yes

Is the Pool or Spa

therm ost at s elect ed f or

the correct body of water to be heated,

the correct body of

and hav e y ou tried

water to be heated,

and hav e y ou tried

selecting a higher

temperature sett ing?

temperature setting?

NoYes

The heater is equipped

with a f iv e minute

delay . Wait at least

f ive minut es to allow

delay . Wait at leas t

the timer to reset.

five minutes to allow

the timer to reset.

Is the unit operating

correctly ?

Contact

AquaCal

for Assistance at

AquaCal

800-786-7751

TROUBLESHOOTING FLOWCHART

Does the display read : "FS" ?

Heat Pump Running... but is it Heating?

(Assumes Heating Indicator Light is Illuminated)

START

Is the air being discharged

degrees cooler than the

outside air?

rises.

Yes

Is the air being discharged

out of the top of the heat er 9-12

out of the top of the heater 9-12

HEAT ONLY MODELS: "FS"

display ed indicates air

temperature m ay be too low to

support the heat er's

operation. Heater will remain in

def rost unt il air temperat ure

HEAT-COOL MO DE LS: "F S"

indicat es heater is def rosting.

Yes

Is the pool pum p ti mer

set to allow extended

operation of the heater?

HEAT ONLY MODELS: Has t he air

tem perature rem ained abov e

38ºF for sev eral hours and "FS"

38ºF f or sev eral hours and "F S"

has been dis played t hroughout

the period?

HEAT-COOL MO D E LS : H a s "FS"

HEAT-COOL MODELS: Has "FS"

remained dis played longer than

5-minut es (I f y es , shut heater

HEAT ONLY MOD ELS : Ambient

condit ions too cold to operate

HEAT ONLY MOD ELS: Ambient

condit ions too cold to operate

heater.

HEAT-COOL MOD ELS : "FS"

HEAT-COOL MO DE LS: "F S"

display ed f or 5-minutes or less

indicat es normal def rost

display ed f or 5-minutes or less

heater.

operation.

indicat es normal def ros t

operation.

the period?

5-minut es (I f y es , s hut heater

of f. )?

Yes

Ext end the pool pum p's

time required in c ooler

hours of operation t o

Ext end the pool pump' s

accommodate

hours of operation to

accommodate

additional heater run

time required in cooler

condit ions.

Is the heater

perf orming

adequately ?

Proble m

Solv e d.

Call AquaCal

for Assistance:

800-786-7751.

Yes

Problem

Solv ed.

800-786-7751.

TROUBLESHOOTING FLOWCHART

Water Coming from Heat Pump

When the heater is operating,

it is normal to produce up to 8

gallons of condensation

gallons of condensat ion

(water) per hour. If water

drainage seems excessiv e,

proceed to TE STIN G.

drainage seems exces siv e,

proceed to TE STIN G.

Sanitizer Test

Did t he test result s

Did t he t est result s

indicate the presence

of sanitizer?

Yes

START

Has the "Heat ing" lamp been

If using chlorine or bromine as a pool/s pa sanit izer,

use a test strip or test k it t o determ ine whether t he

If using chlorine or bromine as a pool/s pa sanit izer,

water is from the pool or is normal condens ation.

use a test strip or test k it t o determ ine whether t he

water is from the pool or is normal c ondensation.

An alternativ e method of determining a water leak in

An alternativ e method of det ermining a water leak in

the heater is to t urn the heat er of f f or a few hours,

leav e t he water pump running, and see if water

the heater is to t urn the heat er of f f or a few hours,

continues to come f rom the heater.

leav e t he water pump running, and see if water

continues to come f rom the heater.

START

illuminated?

Has the "Heat ing" lamp been

illuminated?

TESTIN G:

TES TIN G:

This would

indicate the water

present is f rom

normal

condensation.

If heater has not run recently ,

and water is coming

and water is com ing

f rom the heater, heater m ay

f rom the heater, heat er may

hav e a water leak.

hav e a water leak .

Turn- Off Tes t

Does water cont inue

to drain f rom t he heater

to drain f rom the heater

af ter the heater has been

off for several hours?

of f f or sev eral hours?

Yes

Proble m

Solved.

Solv ed.

Shut off Water Pump

and Call AquaCal for

Assistance:

800-786-7751

Yes

Models:

100, 110 120, 135, and 155

101, 111, 121, and 156

HEATING ONLY

HEATING - COOLING

INSTALLER-SPECIFIC

INFORMATION

FOLLOWS

Installation

Specifications

Controls Configuration

+ 184 hidden pages

Aquacal 135, 111, 101, 110, 156 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual