Aputure LS 300x Product Manual

ai15858101745_LS_300x Product_Manual_EN.pdf 1 2020/4/2 下午2:49

LS 300x

Product Manual

English

ai15858101745_LS_300x Product_Manual_EN.pdf 2 2020/4/2 下午2:49

Foreword

Thank you for purchasing Aputure “Light Storm” LS 300x.

The Aputure LS 300x is a Bi-color Point Source LED Light
Fixture. We've taken all of your favorite features of the
daylight-balanced 300d II and added Expanded Bi-color CCT
control, making it the first Bowens Mount Bi-color LED that
can be used with optical modifiers properly.

IMPORTANT SAFETY INSTRUCTIONS

When using this unit, basic safety precautions should always
be followed, including the following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any fixture is used
by or near children. Do not leave the fixture unattended
while in use.

3. Care must be taken as burns can occur from touching hot
surfaces.

4. Do not operate the fixture if a cord is damaged, or if the
fixture has been dropped or damaged, until it has been
examined by qualified service personnel.

5. Position any power cables such that they will not be tripped
over, pulled, or put into contact with hot surfaces.

6. If an extension cord is necessary, a cord with an amperage
rating at least equal to that of the fixture should be used.
Cords rated for less amperage than the fixture may
overheat.

7. Always unplug the lighting fixture from the electrical outlet
before cleaning and servicing, or when not in use. Never
yank the cord to remove the plug from the outlet.

Detailed product manual for Light Storm can be found on www.aputure.com .

-1-

ai15858101745_LS_300x Product_Manual_EN.pdf 3 2020/4/2 下午2:49

8. Let the lighting fixture cool completely before storing.

9. To reduce the risk of electric shock, do not immerse this
fixture in water or any other liquids.

10. To reduce the risk of fire or electric shock, do not
disassemble this fixture. Contact [e-mail] or take
it to qualified service personnel when service or repair
work is required. Incorrect reassembly may cause electric
shock when the lighting fixture is in use.

11. The use of an accessory attachment not recommended
by the manufacturer may increase the risk of fire, electric
shock, or injury to any persons operating the fixture.

12. Power this fixture by connecting it to a grounded outlet.

13. Please remove the protective cover before powering on
the light.

14. Please remove the protection cover before using the
reflector.

CAUTION

15. Please do not block the ventilation and do
not look at the light directly when it is
powered on.

DO NOT TOUCH LED

Light Source Surface

16. Please do not place the LED lighting fixture near any
liquids or other flammable objects.

17. Only use a dry microfiber cloth to clean the product.

18. Please have the product checked by an authorized
service personnel agent if your product has a problem.

19. The malfunctions caused by unauthorized disassembly
are not covered under the warranty.

20. We recommend only using the original Aputure cable
accessories. Please note that our warranty for this
product does not apply to any repairs required due to
any malfunctions of unauthorized Aputure accessories,
although you may request such repairs for a fee.

-2-

ai15858101745_LS_300x Product_Manual_EN.pdf 4 2020/4/2 下午2:49

21. This product is certified by RoHS, CE, KC, PSE, and FCC.
Please operate the product in full compliance with the
operation standards. Please note that this warranty does
not apply to repairs arising from malfunctions, although
you may request such repairs on a chargeable basis.

22. The instructions and information in this manual are
based on thorough, controlled company testing
procedures. Further notice will not be given if the design
or specifications change.

SAVE THESE INSTRUCTIONS

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.

Warning:

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try reorient or relocate the receiving antenna.

-3-

ai15858101745_LS_300x Product_Manual_EN.pdf 5 2020/4/2 下午2:49

Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a dierent circuit than the receiver is
connected to.
Consult the dealer or an experienced radio/TV technician for help.

RF Warning Statement:

This device has been evaluated to meet general RF exposure requirements.

Check list

When you unbox the product, please make sure all the items listed below are included.
Otherwise, please contact the seller immediately.

Protection

Cover (1 pc)

Paracord

Strap(1 pc)

300x Lamp
Head (1 pc)

VA-Remote RC1+

(1 pc)

Cable Tie Cable Tie

Neutrik® powerCON AC
Power Cable (6m) (1 pc)

Cable Relief Hook

(1 pc)

55° Hyper-Reflector

(1 pc)

5-Pin Male-to-Female

XLR Head Cable (3m) (1 pc)

Quick-Release

"Lightning Clamp"

-4-

(1 pc)

Control Box

(1 pc)

Carrying Case

(1 pc)

ai15858101745_LS_300x Product_Manual_EN.pdf 6 2020/4/2 下午2:49

Product Details

1. Light

Bowens Mount

Release Latch

Bowens Mount

LED Light Source
Optical Blending
Prism

55° Hyper-Reflector

Label

Made in China

UID

5-Pin Male XLR Receiver

Yoke

Cable Relief Hook

Ratcheting Disk

Brake Handle

2. Controller box

Paracord Strap Plate

OLED Display

Channel Setting /

FX: Intensity Selection

Lighting Control Mode /

FX: Lighting Eects Toggle

Brightness Control Wheel

/ Menu Button

CCT Control Wheel

/ Preset Button

Power Button

T-Handle
/ Baby Pin

Mounting Screw

Group Setting /
FX: Frequency Selection

Wireless Control Selection
/ FX: Trigger

-5-

Baby Pin Receiver/Mounting
Column (5/8in. / 16mm)

Antenna Box

Floor Stand

USB Port

Quick-Release
Plate

Battery Plate

(*Anton Bauer or
V-mount)

Floor Stand

ai15858101745_LS_300x Product_Manual_EN.pdf 7 2020/4/2 下午2:49

PUSH

5-Pin Female XLR Power Output

3. VA-Remote RC1+

Channel Indicators

Group A On/O

Group B On/O

Group C On/O

FX Button

Group D On/O

Channel Selector

CR2302 Battery Compartment

Installations

1. Installing the cable relief hook

DMX IN Port DMX OUT PortNeutrik®

powerCON

Power Input

Group A Dimming Controls

Group B Dimming Controls

Group C Dimming Controls

Group C Frequency & CCT Controls

Group D Dimming Controls

Group D Frequency & CCT Controls

PUSH

-6-

Notice: Always remove the protection cover prior to turning on the light. Always re-install the cover when packing it away.

ai15858101745_LS_300x Product_Manual_EN.pdf 8 2020/4/2 下午2:49

2. Attaching/detaching the protection cover

Pull back the retaining pin, rotate the cover clockwise, then detach the cover.
To reattach the cover, insert it into the Bowens mount and rotate counterclockwise.

3. Attaching/detaching the Hyper-Reflector

To install the reflector, pull back the retaining pin, insert the reflector into the Bowens
mount, and rotate it counterclockwise as shown in the following pictures.
To remove the reflector, pull back the retaining pin and rotate the reflector clockwise.

4. Setting up the Light

Mount the light onto a light stand, then fix it in place using the T-Handle/Mounting
Screw on the Baby Pin Receiver/Mounting Column (5/8in. / 16mm). Then loosen/tighten
the handbrake locking mechanism on the yoke to adjust the fixture's angle of tilt.

-7-

* Hang the cable from the head cable relief hook

* Disconnect the XLR head cable by pushing down on the locking tabs on the female XLR connectors,

PUSH

ai15858101745_LS_300x Product_Manual_EN.pdf 9 2020/4/2 下午2:49

5. Instructions for the Quick-Release "Lightning Clamp"

1) Clamp the Lightning Clamp onto a light stand.

2) To attach the control box, rotate the release lever to unlock the quick-release
baseplate, then mount the control box onto the Lightning Clamp (the release
lever will automatically spring back).

3) To remove the control box, grasp it firmly, then unlock the quick-release plate by
turning the release lever, and detach the control box.

1

2

1

2

Specifications

Weight

* The Quick-Release "Lightning Clamp" can clamp onto square or round pipe with a
diameter between 2-5cm or 0.79-1.97in.

670g / 1.48lbs 10.35x8.74x12.5cm / 4.07x3.44x4.92in

Sizes (L*W *H)

6. Connect the light to the control box

Connect the light to the control box using the 5-Pin Male-to-Female XLR Head Cable.

XLR Locking SlotXLR Locking Slot

XLR Locking Tab

then remove the cable.

XLR Locking Tab

to manage and reduce tension on the cable.

-8-

xture's maximum output. Plugging the light into AC

or using two batteries allows you to utilize the light's full output. When powering the light from a single battery, you mus

* Do not use non-14.4v batteries (batteries with voltages outside of the 12-16.8V range). Using higher voltage batteries will

cations mentioned above. If non-compatible

* Customers can choose V-Mount or A-Mount battery plates for their control boxes upon purchase according to their needs.

PUSH

ai15858101745_LS_300x Product_Manual_EN.pdf 10 2020/4/2 下午2:49

7. Powering up the controller

1) Powering by AC

AC 100V-240V

1

~

~

To disconnect the Neutrik® powerCon cable, pull back on the yellow release tab on the
cable connector, and rotate the connector counterclockwise.

2) Powering by Batteries

Neutrik® powerCON

Male Connector

2

Neutrik® powerCON Female

Locking Connector

* Batteries: Voltage 12~16.8V; Recommended ≥15A continuous discharge.
* The LS 300x can be operated using a single battery for up to half of the 

battery on the right side of the of the control box, or the light will not turn on.

damage the power supply and the lighting xture.
* Only use batteries that support the necessary continuous current discharge speci
batteries are used, the batteries will enter a protection state and the lighting xture will not operate as intended.

V-Mount Battery Anton Bauer Battery

-9-

power

t install the

ai15858101745_LS_300x Product_Manual_EN.pdf 11 2020/4/2 下午2:49

8. Insert the button battery to power VA-Remote RC1+

Remove battery compartment Install button battery and insert

it into the VA-Remote RC1+

Operations

1. Press the power button to turn the light on and o

CCT

Battery Level/
AC Power Symbol

Channels

Groups

Wireless Control Mode

Remaining Operating
Time

Dimming Curve

Brightness

* Default: Channel 1 , Group A

2. Manual Control

1) Rotate the Brightness Control Wheel to adjust the intensity of the light
from 0-100%.

-

+

-10-

* As of writing this the Fireworks eect worked in a CCT range presets include three choices of

3200K/5600K/Random.

** When controlling the lightning eect, short press the Trigger button to single trigger the lighting

eect; long press the Trigger button to enter the Lightning Cycle Mode.

ai15858101745_LS_300x Product_Manual_EN.pdf 12 2020/4/2 下午2:49

2) Rotate the CCT Control Wheel to adjust the color temperature of the light
from 2700K-6500K.

-

+

3) Lighting FX Mode

Press and hold the Eects button for 2 seconds to activate Lighting FX mode, then
short press the Eects button to toggle between Paparazzi, Fireworks, Faulty Bulb,
Lightning, TV, Pulsing, Strobe, Explosion, Fire, etc.

a. Paparazzi Eect b. Fireworks Eect*

c. Faulty Bulb Eect d. Lightning Eect**

-11-

* As of writing this the TV eect worked in CCT range presets and you cannot set a fixed base CCT.
** When controlling the explosion eect, short press the Trigger button to single trigger the

lighting eect.

***As of writing this the Fire eect worked in CCT range presets and you cannot set a fixed base CCT.

ai15858101745_LS_300x Product_Manual_EN.pdf 13 2020/4/2 下午2:49

e. TV Eect*

g. Strobe Eect

f. Pulsing Eect

h. Explosion Eect**

i. Fire Eect***

When in Lighting FX mode, short press the "Intensity" button to enter Intensity
Adjustment Mode. Then rotate the Brightness Control Wheel to adjust the intensity
from 10%-100% as displayed on the screen.

-12-

* As of writing, you cannot set a fixed base CCT for certain eects, such as: Fireworks, TV, and Fire.

** If the light is powered o, upon turning on again, the light will resume its last saved setting.

*** When setting up the device with the Bluetooth mobile application, the corresponding name of the

fixture is LS 300x ****** (six digits + letters represent the fixture's serial number).

ai15858101745_LS_300x Product_Manual_EN.pdf 14 2020/4/2 下午2:49

When in Lighting FX mode, short press the "Frequency" button to enter Frequency
Adjustment Mode. Then rotate the Brightness Control Wheel to adjust the frequency
of the eect from 1 to 10 and R (Random) as displayed on the screen.

When in Lighting FX mode, rotate the CCT Control Wheel to adjust the base CCT of the
lighting eect from 2700K to 6500K as displayed on the screen.

4) Wireless Connectivity Modes

Press the Wireless/Trigger button in order to switch between 2.4GHz Wireless Remote
Control, Bluetooth SIG Mesh Sidus Link App Control***, and no wireless control.

-13-

ai15858101745_LS_300x Product_Manual_EN.pdf 15 2020/4/2 下午2:49

5) Press the MENU button to enter the system menu interface, as shown below.

6) DMX mode

Press the MENU button to enter the system menu, rotate the dimming wheel to
select DMX mode and press the MENU button again to enter DMX mode.

When in DMX mode, rotate the brightness control wheels to set the device's DMX
channel. Then press the MENU button to take you back to the Menu interface.

-

+

7) Dimming curve mode

Press the MENU button to enter the system menu, rotate the dimming wheel to
select Dimming Curve, and press the MENU button again to enter the dimming curve
selection menu. Using the wheel to choose from exponential (Exp), logarithmic (Log),
S-Curve, or linear dimming curves, and press the MENU button to make your
selection.

-14-

** When Studio Mode is active, the light will turn on as soon as it receives power, without having to

press the power button.

**** The light must be connected to your mobile device using the Sidus Link mobile application, and

not via your device's typical Bluetooth connection menu.

*** Studio Mode is active as the factory default.

* In "Force Mode" the fan will continuously spin at its maximum speed. In "Auto Mode" the fan will only

begin spinning when the light has reached 45°C.

ai15858101745_LS_300x Product_Manual_EN.pdf 16 2020/4/2 下午2:49

8)

Fan mode

Press the MENU button to enter the system menu, rotate the dimming wheel to select
Fan Mode, and press the MENU button again to enter Fan Mode. Use the wheel to select
between Force* and Auto, then press the MENU button to confirm your selection.

9) Studio mode

Press the MENU button to enter the system menu, rotate the dimming wheel to select
Studio Mode, and press the MENU button again to enter the Studio Mode** menu.
Once in the menu, use the wheel to choose between "YES"*** or "NO" and press the
MENU button to confirm your selection.

10) Bluetooth reset

(1) Press the MENU button to enter the system menu, rotate the dimming wheel to
select BT Reset. Press the MENU button again to enter the Bluetooth Menu. Use the
wheel to select "YES" to reset the Bluetooth pairing (the pop-up window displays the
current reset progress and is completed within 5 seconds); or select "NO" to return to
the previous menu.

(2) After resetting the light's Bluetooth connection, your mobile phone or tablet will be
able to connect to and control the light****.
(3) If the Bluetooth Reset fails, a [Reset Failed] screen will pop-up, and the light will
return to Bluetooth mode after 2 seconds.

-15-

* Only FAT16 and FAT32 storage formats can be used for firmware updates. Incompatible formats

will result in the screen displaying a format error and will return to the main menu.

** DO NOT unplug the light or the USB flash drive during the update process. In the case of an

unexpected power failure, DO NOT remove the USB flash drive. When the power is restored, the

fixture will automatically resume the update process. After successfully updating the firmware,

the fixture will automatically restart.

* The factory default language is English.

ai15858101745_LS_300x Product_Manual_EN.pdf 17 2020/4/2 下午2:49

11)

Language

Press the MENU button to enter the system menu, rotate the dimming wheel to select
Language, and press the MENU button again to enter the Language menu*. Use the
wheel to select from the available languages. Initial languages include "English" and
"Chinese".

12)

USB Mode

(1) The control box has a built-in USB port for firmware updates (for both the control
box and lamp head). Insert a compatible USB* flash drive into the USB port.
(2) To update the light's firmware, press the MENU button to enter the system menu,
rotate the dimming wheel to select USB Mode, and press the MENU button again to
enter the Update menu. Use the wheel to select "YES" or "NO". If a USB flash drive
containing a firmware update is mounted in the USB port, the screen will display an
update progress bar**. If you choose “NO”, press MENU button then it will return the
menu interface.
(3) If a USB flash drive is not inserted into the USB port of the flash drive does not
contain a firmware upgrade file, entering the Update menu and choosing "YES" will
return you to the system menu interface.

13)

OTA Mode

You can also do an OTA wireless firmware update using the Sidus Link mobile app.

-16-

ects, while

ai15858101745_LS_300x Product_Manual_EN.pdf 18 2020/4/2 下午2:49

3. Remote Control

You can control the LS 300x from any channel or group configuration.

* Light Storm lights have three channels (1/2/3) and four groups (A/B/C/D).
* Only groups "C" or "D" can be used to control brightness, CCT and lighting e
groups "A" and "B" can only be used to control brightness.

1) Configuring channel and group settings on the control box

Press the CHANNEL button to toggle between channels 1, 2, & 3.

Press the GROUP button to toggle between groups A, B, C, & D.

2) Configuring channel settings on the remote

Press the CH button to toggle
between channels 1, 2, and 3)

“ ” indicator lights

-17-

* This remote will not work when the light is in DMX mode.

** The remote control will only control the operation of the light when the fixture is in 2.4Ghz Wireless

Control Mode.

* The remote control can only be used to adjust CCT if the lights are in groups C or D.

ai15858101745_LS_300x Product_Manual_EN.pdf 19 2020/4/2 下午2:49

3) Adjusting brightness

Press A/B/C/D to toggle the lights on or o, press ( / ) to adjust the brightness of
the light from 0 to 100% accordingly.

4) CCT Control

In normal light control mode, press the ( / ) buttons to adjust the light's output CCT.

In FX Mode, press the ( + / ) buttons to adjust the lights output CCT.

-18-

* The remote control can only be used to operate lighting eects if the lights are in groups C or D.

DMX512

PUSH

PUSH

PUSH

DMX512

ai15858101745_LS_300x Product_Manual_EN.pdf 20 2020/4/2 下午2:49

5) FX Control

Press the ( + / ) button to enter or exit lighting eect mode. Press the
( + / ) to toggle between dierent eects.
Press the ( / ) buttons to adjust the output of the light. Press the ( / ) buttons
to toggle the eect frequency.

Enter or Exit Eect Mode

a. Paparazzi Mode

b. Fireworks Mode

c. Faulty bulb Mode

d. Lightning Mode

e. TV Mode

f. Pulsing Mode

g. Strobe Mode

h. Explosion Mode
i. Fire Mode

4. Connecting to DMX

1) Connect a standard DMX controller

OUTPUT

OUTPUT

DMX512

DMX512

Connecting DMX to only one 300x

Daisy chaining multiple lights using DMX

-19-

* The default DMX channel is "001".

** The range of DMX channels is 1 to 512.

PUSH

PUSH

DMX512

ai15858101745_LS_300x Product_Manual_EN.pdf 21 2020/4/2 下午2:49

* The DMX interface schematic is shown in the pictures below:

234

1

5

Data 1+
(Primary Data Link)

Data 1­(Primary Data Link)

Signal Common

2) Channel Selection

In DMX mode, match the channel of your DMX controller with the light, and then adjust
accordingly.

5. Controlling Device Via DMX

1) Connect the DMX controller's OUTPUT to the 300x's controller INPUT
as shown in the figure below.

OUTPUT

DMX512

Data 2- (Optional
Secondary Data Link)

Data 2+ (Optional
Secondary Data Link)

Data 1+
(Primary Data Link)

Data 1­(Primary Data Link)

Signal Common

3

4

2

1

5

Data 2- (Optional
Secondary Data Link)

Data 2+ (Optional
Secondary Data Link)

-20-

ai15858101745_LS_300x Product_Manual_EN.pdf 22 2020/4/2 下午2:49

2) DMX Chart

DMX Channel Values / Functions

（6 DMX Channels）

Channel Value Function

1

0-255 Intensity 0 to 100%

0-5 2700K

6-10 2800K

11-15 2900K

16-20 3000K

21-25 3100K

26-30 3200K

31-35 3300K

36-40 3400K

41-45 3500K

46-50 3600K

2

51-55 3700K

56-60 3800K

61-65 3900K

66-70 4000K

71-75 4100K

76-80 4200K

81-85 4300K

86-90 4400K

91-95 4500K

96-100 4600K

Dimmer

CCT Control

2

101-105 4700K

106-110 4800K

111-115 4900K

116-120 5000K

121-126 5100K

126-130 5200K

131-135 5300K

136-140 5400K

141-145 5500K

146-150 5600K

151-155 5700K

156-160 5800K

161-165 5900K

166-170 6000K

171-175 6100K

176-180 6200K

181-185 6300K

186-190 6400K

191-195 6500K

196-255 Undefined

Frequency Control

0-19 1

20-39 2

40-59 3

60-79 4

-21-

* In DMX mode, intensity, CCT, FX frequency and lighting eects can only be controlled by a DMX

controller.

** When controlling multiple 300x lights independently (i.e., A and B), oset each light by 6 channels. If

you set light A at DMX 001, set light B at DMX 007, to control A and B separately on the DMX controller.

ai15858101745_LS_300x Product_Manual_EN.pdf 23 2020/4/2 下午2:49

80-99 5

100-119 6

120-139 7

3

140-159 8

160-179 9

180-199 10

200-219 R

220-255 Undefined

Mode Selection

0-127

4

128-255

0-19

20-39

40-59

6. Using the Sidus Link APP

You can download the Sidus Link app from the iOS App

Manual Mode

FX Mode

FX Control

Paparazzi

Fireworks

Faulty Bulb

60-79

80-99

100-119

5

120-139

140-159

160-178

180-255 Undefined

0 Start Point

1-127 Single Trigger

128-255

6

0

1-127

128-255

Lightning

TV

Pulsing

Strobe

Explosion

Fire

IN Lightning mode

Cycle Mode

IN Explosion mode

Start Point

Single Trigger

Undefined

Store or Google Play Store for enhance the functionality of
the light. Please visit sidus.link/app/help for more details
regarding how to use the app to control your Aputure
lights.

-22-

ai15858101745_LS_300x Product_Manual_EN.pdf 24 2020/4/2 下午2:49

Specifications

Operating Current

Power Supply

CRI

Radio Frequency Channels

Groups

Battery requirement APP Control Type Bluetooth

Light

Sizes

(L*W*H)

Controller box

Anton Bauer Battery

Controller box

(V-Mount)

3.5A

AC 100～240V

50/60Hz

≥96TLCI ≥95CQS

≥96

2.4GHz

A/B/C/D

12V-16.8V

15A

29.84*21.56*34.45cm / 11.75*8.49*13.56in

27.86*12.67*8.73cm / 10.97*4.99*3.44in

27.86*12.67*9.67cm / 10.97*4.99*3.81in

Power Consumption

Cooling Mode

Color Temperature

Remote Ability

350W maximum

Active Cooling

2700K~6500K

1/2/3

≤100m

-23-

ai15858101745_LS_300x Product_Manual_EN.pdf 25 2020/4/2 下午2:49

Photometrics

DistanceCCT

Bare Bulb

3200K

Hyper-Reflector

Bare Bulb

4300K

Hyper-Reflector

Bare Bulb

5500K

Hyper-Reflector

* This is an averaged result, the number might be slightly dierent on each light.

1m

474 (fc)

5100 (lux) 580 (lux) 220 (lux)

1505 (fc) 121 (fc) 42 (fc)

16200 (lux) 1300 (lux) 450 (lux)

697 (fc) 74 (fc) 32 (fc)

7500 (lux) 800 (lux) 350 (lux)

2257 (fc) 195 (fc) 65 (fc)

24300 (lux) 2100 (lux) 700 (lux)

585 (fc) 65 (fc) 23 (fc)

6300 (lux) 700 (lux) 250 (lux)

1904 (fc) 158 (fc) 51 (fc)

20500 (lux) 1700 (lux) 550 (lux)

3m 5m

54 (fc) 20 (fc)

Trademarks

Bowens is a trademark registered by Bowens in China and other countries.
Anton Bauer is a trademark registered by Anton Bauer in the US and other countries.
Neutrik® is a trademark registered by Neutrik® in the US and other countries.

-24-

ai15858101745_LS_300x Product_Manual_EN.pdf 26 2020/4/2 下午2:49

Add

:

F/3, Building 21, Longjun Industrial Estate, Heping West Road, Shenzhen, Guangdong

Aputure Imaging Industries Co.,Ltd.

Inspection: Qualified

Aputure Imaging Industries Co., Ltd.

Add: F/3, Building 21, Longjun industrial estate,

HePing West Road, Shenzhen, Guangdong

E-MAIL: [e-mail]

Sales Contact: (86)0755-83285569-613

Buyer Phone

Buyer Add

Franchiser Seal

Purchase Date

Buyer Name

Serial No.

Item Name

date of purchase. For more details of warranty vis it www.aputure.com

from defects in material and workmanship for a period of one (1) year after the

Aputure Imaging Industries Co., Ltd. warrants the original consumer purchaser