Page 1
LS 1
Product Manual
English
Page 2
Foreword
Thank you for purchasing the Light Storm
The Light Storm
manufactured carefully to have over 95 CRI value. Delicate design and elaborating production make a
robust but exquisite housing, which can fulll low forward heat of the xture.
solutions. You can use V-Mount or Anton Bauer battery in a location shooting. Besides, adapter
attached is for your indoor shooting.
temperature (
brightness and color temperature of
protocol. Light Storm, the best choice for your shooting.
LS 1
includes
LS 1s
and
LS 1c
. It is made of 1536 lamp beads which are designed and
LS 1
LS 1c
). Two antennas can cover all the surrounding within 360°. You can also control the
is with the ability to adjust the brightness and the color
LS 1
by a DMX console which is under the standard DMX512
Instructions
Please read this product manual carefully.
Keep this product manual. Always includes this product manual when passing the products on to
the third parties.
Heed all warnings and follow all instructions in this product manual as stated.
Please do not disassemble or modify the Light Storm
product malfunction.
Please do not handle with wet hands or immerse in or expose to water or rain, or it could result in
re or electric shock.
Please do not use the Light Storm
explosion.
Please keep all liquids and ammable gas away from the Light Storm.
Keep away from strong sunlight or other high temperature, or it may explode.
Please do not damage, disassemble, drag or wind power cable. Do not place heavy things on the
Light Storm, or it may cause re or electric shock.
Please clean the Light Storm
Use of original Aputure cable accessories is recommended. Please note that this warranty does not
apply to repairs arising out of the malfunction of non-original Aputure accessories, although you
may request such repairs on a chargeable basis.
The product is certicated by ROSH, CE and FCC. Please operate the product in full compliance with
the operation standards. Please note that this warranty does not apply to repairs arising from
malfunction, although you may request such repairs on a chargeable basis.
The instructions and information in this manual are based on thorough, controlled company testing
procedures. Further notice will not be given if the design or specications change.
LS 1
in the presence of ammable gas, or it could result in
LS 1
with a dry cloth.
Intended use
Intended use of the Light Storm
The user has read the instructions of this manual.
The user is using the products within the operating conditions and limitations described in this
product manual.
“Improper use” means using the products other than as described in these instructions or under
operating conditions which dier from those described herein.
Detailed product manual for Light Storm can be found on the movie solution page on www.aputure.com .
LS 1
means:
LS 1
LS 1
, or it could result in electric shock or
-1-
LS 1
oers dual power
Page 3
Item check list
Before starting, please check that all the following items have been included
with the Light Storm
immediately.
LS 1
. If anything is missing, contact your dealer
Hook
Clamp (5 PCS)
Light
Warranty Product manual
Tracing papers (10 PCS）
Controller box
（*Color temperature
wheel only for LS 1c）
ControllerButton battery
-2-
AC/DC adapter
Power cable
Magic strip
Connect cable
Buckle
Page 4
Nomenclature
1. Light
2. Controller box
3. Controller
Channel chosing button
Battery compartment
Eyelet bar
Socket
Power switch
Display window
Brightness wheel
Color temperature wheel
(*only for LS 1c)
DMX input/output
Channel indicators
Group A on/o
Group B on/o
Group C on/o
Group D on/o
Cable box Cooling ns
Antennas
(*The signal strength is the best
when pulling the antennas as
the picture's show.)
Battery Mount
(*Anton Bauer or V-mount)
DC power socket
-3-
U-frameLED beadsBarn door frame Barn door
tube
Group A brightness button
Group B brightness button
Group C brightness button
Group C color temperature button
Group D brightness button
Group D color temperature button
Clamp handleHook Supporting
Tilt knob
Page 5
4. Display window
Channels indicator
Groups indicator
Channel setting button
DMX channel setting button(+)
Group setting button
DMX channel setting button(-)
DMX indicator
Brightness percent indicator
Color temperature indicator
(*only for LS 1c)
DMX model setting button
Installations
1. Install the hook
2. Install the light
1) Turn around the clamp handle to install the light on the tripod.
2) Set the light at a specic angle, and pull or turn around the tilt knob to fasten the light.
-4-
Page 6
3. Insert the connect cable dot to dot to power the light .
*Tie the connect cable around the hook
4. Power the controller box
1) Powered by the adapter
AC 100V-240V
Locking
spring
* Please pull the power adapter out by pushing the locking spring down on the controller box.
-5-
Locking
slot
Page 7
2) Powered by the battery
V-Mount Battery Anton Bauer Battery
* Battery output current ≥ 8A;
* Please choose the model of the Light Storm by your battery need.
5. Clip the tracing paper by the clamps
6. Insert the button battery to power the controller.
-6-
Page 8
Operations
1. Press power switch to turn on the Light Storm
LS 1.
*“Channel 1 ,Group A” is by default.
*The brightness is 10% and the color temperature is 3200K
(LS 1c)
by default.
2. Manual controlled by the controller box
1) Brightness adjustment and display
2) Color temperature adjustment and display
3. Remote controlled by the controller
You can control the LS 1 of channel 2, group C according to the following directions.
1) The controller box setting
*1) Channel setting and display
-7-
(*only for LS 1c)
Page 9
*2) Group setting and display
2) The controller setting and display
Press ( ) to set the channel 2
“ ” indicator lights
The controller setting is nished.
*The Light Storm has three channels (1/2/3) and four groups (A、B、C、D).
3) Brightness and color temperature adjustment
Press ( or ) of group C to adjust the brightness and ( or ) of group C to adjust the
color temperature. The brightness varies in 1%, and the color temperature varies in 100k at one press.
Brightness changes between 10 and 100; Color temperature changes between 32 and 55
-8-
(olny for LS 1c).
(*only for LS 1c)
Page 10
4.The DMX control
1) Connect a standard DMX console
OUTPUT
DMX512
DMX512
Only one Light Storm
OUTPUT
DMX512
DMX512
One by one
* See the interface denition of the DMX as the picture shows:
ground
ground
empty
-9-
groundempty
negative
ground
positive
Page 11
2) The DMX setting
*1) Press DMX model setting button on the controller box to enter into the DMX model.
*2) Press the DMX channel setting button (+/-) on the controller box to your needed DMX channel.
3) The standard DMX console control
Control the Light Storm by the standard console within the same DMX channel setting as above.
* Channel 1 is by default when in DMX model.
* DMX channel is between 1 and 512, but is between 1 and 511 for the Light Storm
LS 1c.
Tips and trouble setting
Please turn o the Light Storm
Please do not look at the Light Storm
Please do not keep touching the Light Storm
you injured.
Keep a distance of over 10 meters away from the Light Storm
Suggest to take out of the button battery of the controller if do not use the controller for a long
period .
LS 1
before removing batteries.
LS 1
straightly, or it could damage your eyes.
LS 1
over 5 minutes during lighting, or it could make
LS 1
.
-10-
Page 12
Specifications
Model
Operation Current
Power Supply
Power Input
Beam Angle
Color Temperature
Average Life Span
Cooling Mode
Radio Frequency
Channels
Groups
Remote Range
Light
Sizes
(L*W*H)
Controller box
Anton Bauer Battery
Controller box
(V-Mount)
Brightness (average)
Model
LS 1c
LS 1s
LS 1c
8A
LS 1s
8A
DC 15V DC 15V
120W
45°
3200K-5500K
≥100,000 hours
Natural convection heat transfer
120W
25°
5500K
2.4GHz
1/2/3
A/B/C/D
≤100m
377.8*320.7*33.2 mm
238.0*118.7*48.1 mm
238.0*118.7*59.6 mm
Distance LUX
Footcandles
0.5m
1m
0.5m
1m
(*vertical antennas included)
(*vertical antennas included)
2323
697
2788
929
25000
7500
30000
10000
-11-
Loading...